Search Documents

By Vijia K. Karra

The goal of aggregates producing companies across the United States is to ensure their workers go home safely each day. At the National Institute for Occupational Safety and Health (NIOSH), researchers are pursuing this vision of safety and health through a fact-finding approach for reducing injury illness in various mineral sectors. Surveillance data from Mine Safety and Health Administration (MSHA) has been the source for such analyses. It helps to focus research efforts on key machinery, workers, and their tasks. The second installment of this two-part series follows last month's focus on crushed stone.

By Thomas Varley

Data on the consumption of reagents used in .flotation during the year 1925, in metallurgical plants in the United States, are presented in this paper. Previous reports have covered the same subject for the years 1916, 1919, 1923 and 1924. The data contained herein show departures most radical from even the 1924 practice. Flotation has developed rapidly and on a more scientific basis than ever before. Perhaps more fundamental and useful data have been uncovered during the past two years than in all the years the art has been practiced.

Jan 1, 1926

In the past, mine management has been concerned with removing water from active mining sections primarily because it hampered the movement of mining equipment and aggravated the working condition of the miners. Pumping water to sumps and gravity drainage by ditching have proven successful in mines for minimizing section down time due to water influx. However, with the advent of more strict pollution laws the mining engineer must now be concerned with keeping water out of the section and also with preventing it from causing pollution. A review of the handbooks and textbooks used in the mining engineering curricula reveals that little has been written concerning acid mine water prevention or control in underground coal mines. Additionally, the review of the curricula of mining schools indicates they are not teaching the engineering students the necessary techniques of mine water management as they relate to the abatement of mine water pollution.

Jan 1, 1970

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Table

Jan 1, 1977

By F. E. Wormser

"Arsenic has been recently quoted at 10 1/2 - 11 cents per pound, an increase over the prevailing price of last fall, when arsenic was cents, as against pre-war prices around 4 cents is evidently a sustained demand for this material. The following statements are intended to summarize briefly some particulars regarding arsenic.Commercial arsenic is the white arsenious oxide (As203). This is the form in which it is generally marketed, as the uses of arsenic demand its industrial application in this form. Arsenic as an element finds rather restricted use in the hardening of lead shot, ere it is to some extent replacing the use of antimony, while white arsenic is employed in a variety of manufacturing processes, chief of which is the manufacture of insecticides and sprays. The poisonous nature of most arsenic compounds, the commonly known ones being paris green and lead arsenate, and its relative cheapness, make arsenic a material suitable for this purpose. The stimulation of agriculture during the war greatly increased the demand for arsenical insecticide. Glass making consumes a large amount of arsenic as it has been impart increased brilliancy to the glass. Crude commercial arsenic is often used to kill weeds along railroad tracks. Arsenious oxide is used also for preserving hides, while the disulphide, AS2S2), finds an application in dehairing hides for the finest grade leather, as it least affects the product. Orpiment (As233), is used in textile dyeing. Wall paints and wall paper formerly consumed considerable arsenic in the form of paris green, but this use has been largely,given up due to the poisonous nature of the dust from the product. Sodium arsenate for a similar reason, is now little used in printing where it had found application. The great objection to arsenical yes and paints is the risk of poisoning from use of the manufactured article. Sodium arsenite is the principal poisonous in¬gredient of many cattle and sheep dips. Arsenic compounds are also used medicinally."

Jan 1, 1920

Provide room-and-pillar operators with practical in- formation and guidelines concerning multiple-seam mine design to reduce ground problems associated with the interaction of adjacent working.

Jan 1, 1994

By R. V. Ramani, A. S. C. Owili-eger

The Federal Coal Mine Health and Safety Act of 1969 (sec. 303 (b)) stipulates that no working section of the mine shall contain more than 0.5 percent carbon dioxide and no harmful quantities of other noxious or poisonous gases such as the oxides of nitrogen. The concentration of methane should at all times be maintained below one percent. A split of air returning from any working section shall contain no more than 1.5 percent of methane (sec. 303 (i) (2)) and air that has passed by an opening of any abandoned area shall not be used to ventilate any working place in the coal mine if such air contains more than 0.25 percent of methane (sec. 303 (j)). Methane concentration in the returns from the bleeder entries should not exceed 2.0 percent (sec. 303 (i) (3)), and no air that has passed through an opening which is inaccessible for examination shall be used to ventilate any active areas. While the air quantity requirements alone can easily be met, the governing condition in most mines is the dilution requirements for quality control. A sufficient quantity of air is required to render harmless and carry away noxious and respirable pollutants. In recent years, changes in coal extraction methods, rates of advance, location of available reserves, position of prominent methane sources and horizons, and geological sequences have contributed sig¬nificantly to alterations in rates, patterns and character of numerous methane emissions. Gas production of 10 to 15 million standard cubic feet per day is not uncommon from deep mines (Cervik, 1969). Thus, because of the large capital outlay involved in the instal¬lation and subsequent remedial actions of methane drainage systems, knowledge of gaseous flow patterns and storage characteristics of the

Jan 1, 1974

By Robert F. Chaiken, Thomas H. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Optical technologies have progressed rapidly in the past 15 years. One application of laser technology in underground coal mines currently under evaluation is the remote measurement of explosive methane gas. Federal regulations require that atmospheric monitoring systems used in gassy underground mines where permissible equipment is required shall be intrinsically safe. Mine Safety and Health Administration criteria for the evaluation and testing of intrinsically safe apparatus and associated apparatus contain no specific guidance for optoelectronic components such as diode lasers. The National Institute for Occupational Safety and Health is conducting a study to help provide a scientific basis for developing appropriate safety guidelines for optical equipment in under- ground coal mines. Results of experiments involving ignition of methane-air mixtures by collections of small heated particles of Pittsburgh seam coal and black iron oxide are reported. The inert but more strongly absorbing iron oxide targets consistently ignited methane-air mixtures at lower powers than the coal targets. Minimum observed igniting powers for laser energy delivered by 200, 400 and 800 pm core fiber optic cables and directed onto iron oxide targets in methane-air atmospheres were 0.6, 1.1, and 2.2 W, respectively. Comparisons with the results of other researchers are made. A thermal layer theoretical approach to describing the process is included as an appendix.

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By Lauren Roberts, Lewis Martin, John Goris

The Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health (NIOSH) and Thiessen Team USA, Spokane, WA, have developed a pull claw that can be attached to any accessible friction bolt ring to test the performance (i.e., load-carrying capacity) of bolts without the use of a pull collar. This would allow true random testing of friction bolts, which need to be evaluated to determine if they are still providing an adequate level of support months or years after installation. Such support is critical to maintaining safe working conditions for underground miners.

Jan 1, 2004

By S. P. Howell

The Bureau of lines as repeatedly called attention to dangerous practices in the transportation and opening of kogs of black blasting powder. In 1914 Diwin Higgins (Prevention of Accidents from Explosives in Metal inos, Miners' Circular 19, Bureau of Mines, p. 15) stated "canisters should always be opened by removing the bung. To use a pick or other sharp tool for cutting a hole in the canister is dangerous. After the necessary amount of powder has boon taken out, the canister should be kept closed. The powdor should always be handled at a safe distance from an open light." In 1919, Geo. S. Rice (onthly Statement of Coal line Fatalities for June, 1919, Bureau of Mines, pp. 16 to 18) calls attention to the dangers that arise in underground transportation and handling of explosives, and calls special attmtion to the danger of hauling explosives in motor trips; the unnecessary risk involved in hauling men on the trip at the same time, and the necessity of keeping open lights away from black blasting powder. In 1919 the writer (Sensitiveness of Explosives to Frictional Impact, Tech. Paper 234, Bureau of Mines, pp. 13, 15) called attention to the fact that black blasting powder is not as sensitive to frictional impact as the nitro-glycerin dynamites and the gelatin dynamites. Black powder may be ignited by direct impact and the writer believes that this may occur without presupposing a preliminary spark. It is well known, however, that black blasting powder is very sensitive to ignition by spark flame, or heated materials, and these may be produced by an electric current, by an open light, by incandescent particles from a pipe, cigar, or cigarette, by the tearing of metal sheets or scraping of metal against metal, and possibly, by other means. -- The above discussion will serve to introduce a newly recognized hazard the ignition of black blasting powder by the forcible opening of kegs with wodden tools. The details of three accidents in which kegs of black blasting powder ex- ploded instantly when a wooden tool was driven forcibly through the top of the kegs are as follows: 1. In 1915, a powder man employed by a coal mining company stated that he was opening a 25-pound log of black blasting powder by driving a hole in the top with a wooden sprag when the powder in the leg ho was opening ignitod. This caused the ignition of fifty-two additional 25-pound logs of the powder, and the fatal burning of this and another powder man. The ono making this statement lived five hours after the explosion.

Sep 1, 1920

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

By J. R. Thoenen

This circular is part IV of the third paper (entitled "Sand and Gravel Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part I discussed the use of power shovels, draglines, and excavator cranes; part II discussed the use of power scrapers, slackline cableway excavators and hydraulic monitors; and part III discussed the use of hydraulic, clamshell, ladder, and dipper dredges. This circular discusses haulage equipment in general, particularly the use of industrial cars with locomotives or hoists as the motive power. Part V, to follow, will discuss the use of other types of haulage equipment.

Oct 1, 1935

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workman enter those places, but dine to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

By V. P. Bhavanandan, S. B. Dubbs

The mucus secreted in the respiratory tract provides the first barrier against inhaled particulate and gaseous toxicants. The major component of mucus which is responsible for the physical properties and protective functions of the respiratory mucus is mucin. We have initiated investigations to determine the effects of coal mine dust on the synthesis of respiratory mucin by rat trachea under in vitro and in vivo conditions. In this study we have established optimum conditions-:ro-r~ the asceptic growth and mucin secretion of rat tracheal explants in culture. The best outgrowth of ciliated epithelial cells and maximum mucin production was obtained in CMRL 1066 medium containing 10% fetal calf serum. The explants continued to secrete mucin even after three weeks in culture. For the estimation and characterization of mucins the tracheae were cultured in the presence of [3H] glucosamine and [35S] sulfate or [14C]leucine. The mucins were isolated from the medium by gel filtration, treatment with hyaluronidase, ion exchange chromatography and CsBr density gradient centrifugation. Precipitation of polyanionic material in the culture media with cetyl pyridinium chloride and fractional extraction with NaCl also yielded mucin free of glycosaminoglycans, but in low yields. The tritium label in the purified mucin was distributed in sialic acid (50%) galactosamine (37%) and glucosamaine (13%). The density of purified mucin as determined by CsBr gradient centrifugation was about l.43g per ml in comparison to l.46g per ml for human respiratory mucin with a carbohydrate content of about 80% by weight. Alkaline borohydride treatment released saccharides which contained about 80% of the radioactivity. The effect of adding varying amounts of coal dust to the culture medium is under investigation. (Supported by U.S. Bureau of Mines Grant G1135142, Project 4210).

Jan 1, 1989

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947

By Fred N. Kissell, Jon C. Volkwein

In This Chapter [How inert gas works to prevent methane explosions How inert gas is generated and delivered at highwall mines Volume and quality requirements for inert gas at highwall mines How an inert gas system is operated and Precautions to take during mining to prevent methane explosions] This chapter discusses a method, originally developed by Volkwein and Ulery [1993], to prevent methane explosions during highwall mining. In highwall mining, a horizontal auger or a mining machine enters the coal seam from a surface mine pit at the bottom of a highwall, and the coal is mined out from a series of parallel holes. Explosions can be prevented by injecting inert gas into each hole as it is mined. Coal near the surface has lost most of its methane gas over time. However, in recent years, surface mining has been used for deeper reserves of coal. This trend toward mining deeper reserves has increased the chance of encountering methane, and methane explosions at highwall mining operations have resulted in injuries. HOW INERT GAS WORKS TO PREVENT METHANE EXPLOSIONS A methane explosion requires the presence of sufficient amounts of both methane and oxygen, as well as an ignition source. If the methane cannot be reduced and the ignition source cannot be eliminated, then explosions may be prevented by adding an inert gas, which contains little to no oxygen, to the mixture [FWQA 1970]. Just how much inert gas must be added depends on the mining rate, as well as the composition of the inert gas. An explosibility diagram can be used to show whether a methane mixture is explosive after inert gas is added [Zabetakis et al. 1959] (Figure 10–1). This diagram indicates that gas mixtures fall into one of three range categories—explosive, explosive when mixed with air, and nonexplosive—depending on the percentage of methane and percentage of “effective inert.” Effective inert is calculated from the percentage of “excess nitrogen”3 and percentage of carbon dioxide in the mixture.

Jan 6, 2006

By A. E. Wells

"When the United States entered the World War, the heavy requirements for sulphuric acid in the manufacture of explosives made necessary a definite knowledge of the sulphuric acid capacity of the country. The Bureau of Mines, under the authority conferred by the explosives regulation act, made a thorough survey of the sulphuric acid situation. In this work, which was personally directed by the writer, comprehensive data were collected on the situation and capacities of the various acid plants, sources of supply of raw materials (brimstone, pyrite, pyrrohotite, zinc ores and concentrates, waste sulphur dioxide gases from copper smelting, and spent oxide from gas works), the principal points in regard to manufacturing processes (chamber and contact) and the uses of the acid. The results of this investigaion have recently been published by the Bureau of Mines, as Bulletin 184, entitled ""The Manufacture of Sulphuric Acid in the United States"" by A. E. Wells and D. E. Fogg. The following paragraphs on the uses of sulphuric acid are abstracted from this bulletin.Sulphuric acid is one of the most important of all chemicals, not only because of the large quantities manufactured but also because of the wide use of the acid in many different industrial works. Sulphuric acid is to the chemical industry what iron is to metallurgy. The general public, however, does not realize this fact, for sulphuric acid does not appear in the finished product as does iron and steel, but is only a means to an end. It is essential in many industries, such for example as in the manufacture of phosphate fertilizers, explosives, dyes and petroleum products. In recent years in the United States, especially in the East, the demand for sulphuric acid for chemical and metallurgical industries has been an accurate and sensitive barometer of the general business conditions. This demand for acid responds much more quickly to a general slump or boom in the industrial world than does the demand for iron and steel."

Oct 1, 1920