Search Documents

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Rose L. Ballard

This chapter summarizes data on crude non fuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal non fuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production, The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1986

By M. R. Geer

The ever-increasing need to guard against stream pollution has intensified interest in the problems of handling and disposing of flotation tailing. Therefore, the Bureau of Mines investigated the possibility of using crushed washery refuse to adsorb the free water in thickened flotation tailings on a bench scale and then in a pilot plant because the conventional methods of disposing of coal flotation tailings--impounding them or filtering them so they are dry enough to be conveyed to the refuse dump--are sometimes either impractical because of space limitations or costly because of low filter capacity. Most of the refuse samples tested were of similar mineralogical composition and exhibited similar water retention capability. The amount of crushed refuse required to adsorb the water in a particular tailing was influenced greatly by the fineness of the solids in the tailing and hence the percentage of solids to which it could be thickened. The ratio of crushed refuse to tailing solids required to provide a mixture dry enough to be carried on an inclined conveyor belt varied from 2.4 to 6.4. Several chemical agents that were tested were very effective in turning the free water in tailings into a stable gel. Fly ash also was very effective in adsorbing water.

Jan 1, 1968

By Charles L. Kusik

As part of an effort to establish processes that could be exploited in case of adverse changes in international chromium production and trading patterns, this study was sponsored by the Federal Emergency Management Agency (formerly the Federal Preparedness Agency) through the Bureau of Mines, to experimentally determine the feasibility of recovering chromium from critical scrap metals containing significant quantities of this element. Based on a conceptual pyrometallurgical chromium recovery flowsheet developed at Arthur D. Little, Inc., the experimental program described in this report demonstrated key process steps for the recovery of chromium as ferrochromium in a batch process. The process involves oxidation of chromium into a slag phase, subsequent separation of the slag phase from the remaining metal, followed by reduction of chromium from the slag phase to produce ferrochromium.

Jan 1, 1981

By Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine seals can be remotely constructed in underground coal mines, through vertical boreholes, when direct access to a fire is impossible or considered to be too dangerous. This method has great merit because boreholes can be drilled to specific mine areas and seals can be positioned close to a fire zone. The technology however, can be largely ineffective if the constructed seals do not provide effective barriers to airflow or cannot be used to impound water and other inert materials. Unfortunately, no viable alternatives exist to sealing the entire mine at the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Lake Lynn Laboratory (LLL). Under this effort, Howard Concrete Pumping Company and GAI Consultants, Inc. have joined forces to evaluate a potentially significant improvement to the current state-of-the-art. This paper will cover development of novel technology for remote mine seal construction, evaluation of the materials used, construction practice, and follow-up testing.

By C. B. Manula, R. L. Sanford, R. A. Rivell

The need for a large capacity, high speed computer is more apparent in the revised model than in the original one. Core storage requirements for data and model logic have at least tripled. This dictates the use of one of the large modern machines such as the IBM 360-370 series or the Univac 1108 and 1110, which handle the model without the need for extensive program overlay. Computer time is expensive on these machines, however, and comprehensive analysis has gone into optimizing computer execution time consistent with model information flow sensitivity. For example, revised locomotive tramming routines have been developed which will significantly cut execution time compared to the previous version. Transceiver Applications The computer coding for the model has been developed to enable program execution and testing using a remote terminal on a time sharing system. In fact, nearly all of the coding, debugging, testing and modifications have been performed from a terminal during develop¬ment. The gaming options described in the Model Input Section of this report have been designed so that they are easily changed by the user from any remote site. One restriction on remote applications which could arise, however, is where highly detailed output options are specified, resulting in a large amount of output records which could be handled more efficiently on a high speed printer.

Jan 1, 1974

By R. L. Montgomery

Electronegativities of the rare-earth elements were calculated from heats of formation. The values obtained from different compounds varied widely. The postulates of Pauling's electronegativity theory were interpreted for bonds that are primarily ionic; the study showed that many compounds obey rules of the form expected. Revised electronegativity values are given for the more electropositive elements, including the rare-earth metals (which are near magnesium in electronegativity). Estimates of un-known heats of formation are made from electronegativities and are compared with other estimates. INTRODUCTION Calculation of the electronegativities of the rare-earth elements is interesting to show how these metals stand relative to the other metals and to each other, and also possibly to systematize the thermochemical data on them.

Jan 1, 1960

By R. B. Prater

Research by the Bureau of Mines includes efforts to devise means for maximum recovery of critical and strategic metals from primary and secondary domestic resources. As part of that effort, the Bureau developed a hydrometallurgical process to recover Co, Ni, and Cu from Missouri lead-smelter matte. The process includes leaching with H2S04 plus Mn02 as an oxidizing agent, liquor purification, selective precipitation of CuS, (Co,Ni)S, and MnC03, and crystallization of Na2S04&apos; This report is concerned primarily with liquor purification, in which As and Fe are removed from the leach liquor by pH adjustment and filtration. Two variations of the purification step are described. One variation provides liquor containing <1 mg/L As and Fe but requires two solid-liquid separations, The other is achieved with only one solid-liquid separation but leads to a lower degree of purification.

Jan 1, 1987

By L. W. Higley

Particulates generated in electric furnace (EF) steelmaking constitute approximately 1 to 2 pct of the charge. This flue dust is a rich source of zinc (values are substantially higher than in ore), but although there are several processes for recovering the metal, none are considered economic in the United States. This report reviews extraction technology and presents results of Bureau of Mines reduction-volatilization tests on pelletized EF dusts which achieved high recoveries of zinc. The data are sufficiently encouraging to warrant consideration of EF dusts as raw material for primary zinc smelters.

Jan 1, 1977

By Ann G. Kim

Methane in coal constitutes a serious hazard during mining. Draining the methane from large blocks of coal in advance of mining is an effective method of improving the safety and efficiency of coal mining. Because of the similarity of the two gases, drained methane can be recovered and added to pipeline supplies of natural gas. To effectively apply advance drainage techniques and recover drained gas, a gross estimate of the methane content of coal is necessary. Using data from previous investigations, the virgin reserves of the Pittsburgh coal in the central and southwestern parts of Washington County, Pa., are estimated at over 1.5 billion tons, with a methane content of 50 to 100 fts/ton. The Pittsburgh bed in this area of approximately 265 mi2 contains over 130 billion ft3 of methane.

Jan 1, 1974

This chapter describes the adverse health effects associated with exposure to respirable coal mine dust. Epidemiological studies of underground and surface coal miners in the United States and other countries are discussed. Also discussed are animal studies that add to our understanding of particle deposition and retention in the lungs and associated disease responses. This chapter emphasizes studies that (1) were performed since the passage of the Federal Coal Mine Health and Safety Act of 1969 [P.L. 91- 173], (2) used standardized methods of exposure monitoring and disease classification, and (3) investigated exposure-response relationships between respirable coal mine dust exposure and disease. Several published review articles contain further discussion of health effects studies of coal miners [Attfield and Wagner 1992b; Petsonk and Attfield 1994; Cotes and Steel 1987; Merchant et al. 1986; Morgan and Lapp 1976; Morgan 1975].

Jan 1, 1997

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

By J. J. Cummins

Green River oil shale previously extracted by benzene was heated at 150°, 200°, 250°, 300°, and 350° C for 0.5 to 360 days to determine the rate at which kerogen degrades to thermal products, the types of thermal products formed, and the effect of prolonged low-temperature heating (preheating) upon subsequent assay yields. Thermal decomposition of kerogen at 150° to 350° C is treated as a first-order reaction. The specific reaction rate for kerogen decomposition increases from 2.2 X 10-4 per day at 150° C to 2.0 X 10-1 per day at 350° C. The calculated kerogen activation energy is 19 kcal. Variations in the rate of formation of individual type components of the pyrolytic products were found. Carbon balances show an increase in the amount of kerogen converted to bitumen and oil (from assay of preheated oil shale) as the temperature of preheating increased from 150° to 350° C. Total product from shale preheated at temperatures of 150° and 200° C gave less than 100 percent of Fischer assay yields while the total products from shale preheated at temperatures of 250° to 350° C gave greater than 100 percent of Fischer assay yields.

Jan 1, 1972

By B. W. Gandrud

[The meaning of the term "bauxite&apos; has always been somewhat vague and indefinite, and the term has been used in various applications to denote sometimes a rock, sometimes a mineral, but more frequently an ore. It seems logical to think of bauxite as an ore, however, because a very large part (probably at least 85 per cent) of the entire world&apos;s production of bauxite is at present being used as a source of aluminum and aluminum chemicals. In the United States there are two districts that, produce bauxite - the Arkansas district and the Alabama-Georgia-Tennessee-Mississippi district. The deposits in Mississippi have been discovered recently and are riot as yet productive but it seems reasonable to consider them as apart of the-district hat includes the deposits of Alabama, Georgia, and Tennessee. The, two districts are often referred to as the Arkansas field and the Appalachian field. Of these two the Arkansas field has been by far the largest producer, and at present over 90 per cent of the bauxite production of they United States comes from the Arkansas field. The bauxite industry in the Appalachian field had its beginning in 1889, and since that time the total production of the states of Alabama, Georgia, and Tennessee has been, nearly a million tons. The production of bauxite in this field has languished in the last five, or six, years, and In 1927 its production was only about 14,000 tons, according to Harder4. The recent decrease in production is due mainly to the fact that many .of the known deposits of commercial-grade ore have become exhausted. There are, however, considerable quantities of low-grade bauxite in the Appalachian field, but these have not been available because there has been no satisfactory way of concentrating low-grade bauxite. The quantity, of low-grade material in the Appalachian field is probably, fully as large as the tonnage of commercial ore which the field has already produced.]

Jan 1, 1928

The current procedure for measuring the concentration of respirable coal mine dust is as follows. Each filter is preweighed by the filter manufacturer to ±0.1 mg. Following sampling with the Coal Mine Dust Personal Sample Unit (CPSU) at 2.0 L/min, the filter with coal mine dust is sent to MSHA for weighing. The current MSHA procedure for weighing respirable dust samples uses a Mettler Model AE163 analytical balance in conjunction with an automatic weighing system with a precision of ±0.02 mg [Tomb 19901. Each balance is calibrated twice per day. Quality control for the automatic weighing system includes the systematic weighing of one in eight filters on a second Mettler AE163 balance. Tolerance is set at ±0.1 mg between the two weighings of the same sample. Weights are truncated at the 0.1 mg level (e.g., 3.457 mg is truncated to 3.4 mg) [Bowman et al. 19851. The difference of the two truncated weights is then recorded as the weight of coal dust deposited. The respirable concentration (mg/m3) is computed by multiplying by a correction equal to 1.38 and dividing by the volume of air sampled (2.0 L/min x sampling time [min]).

Jan 1, 1997

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By F. E. Spencer

This Bureau of Mines report provides a complete mathematical description of the algorithm employed by a general multiphase chemical equilibrium program developed particularly for the purpose of studying problems in coal combustion, although the generality of the program will allow its application to any equilibrium system in which an appreciable gas phase is present. When applied to coal combustion problems, the program predicts composition and quantity of slag and unconsumed carbon phases as well as calculates accurately the composition of the gas phase including trace species such as free electrons and ions which are important for predicting electrical properties.

Jan 1, 1973

By Jamie Girard Dwyer, Edward McHugh, Stanley Miller, Jeffrey Whyatt

This user&apos;s guide covers the operation of a suite of three computer programs-Bplane, Bstepp, and Bwedge. These programs can be used to evaluate the potential for plane shear, step-path, and wedge failures along the crest of a slope bench. Such failures reduce the width of a catch bench and may compromise the bench&apos;s ability to catch rolling or sliding material before it reaches miners working below. The Bplane and Bwedge programs address sliding of blocks defined by continuous planar joints. The Bstepp program examines sliding of blocks defined by more complex failure surfaces that include steeply dipping cross joints and may even include breaks across small bridges of intact rock. The programs are applicable to jointed rock masses where the joints are small relative to the overall slope and form a number of sets with uniform statistical characteristics within a slope sector. The theoretical basis, application, and operation of these programs are described.

Jan 3, 2007

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By J. D. Davis

Coke Since the beginning of manufacturing of metallurgical coke in the United States, which dates from about 1859, Pennsylvania has main tamed supremacy in coke production Available statistics for the year 1880 show an output of 3,338,300 short tons, which was neatly trebled by the end of the succeeding 10 years. From this time on the increase was steady, though not rapid, and in 1922 the total production was 13,991,892 tons, which is approximately 37 per cent of the total coke production of the United States. The main reason for the rapid development of the coke industry in Pennsylvania lies in the abundance of coals particularly adapted to beehive coking, for which purpose the Pittsburgh bed in the Connellsville district has long been looked upon as standard At first practically all metallurgical coke was made in beehive ovens, the only exception being the short lived and wasteful method of coking in piles, byproduct owns did not make then appearance until after 1893 The suitability of a beehive coking coal cannot be accurately predicted from its chemical analysis, but it can be said, perhaps, that the volatile matter should be about 32 per cent, and that the oxygen content should not be mole than 10 pet cent or less than 4 per cent The sulphur and phosphorus content should be small-not over 1 25 per cent sulphur and under 0 02 pen cent phosphorus-and the ash content should not be over 7 per cent The Pittsburgh bed at Connellsvnlle fills these requirements well, as may be seen from the following representative analysis. Analysts of coal from Pittsburgh bed Moisture 1 70 Volatile matter 31 10 Fixed carbon 59 80 Ash 7 40 Sulphur 0 85 B t u 13,990

Jan 1, 1928