Search Documents

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By Frank E. Cash

Large quantities of explosives are consumed in the underground mining of ores in the Lake Superior district. Because of the recognized danger of accidentally releasing the potential highly destructive forces contained, the safes possible procedure in the transportation, storage, and use of explosives is necessary. Underground magazines recently constructed in the district give evidence of the earnest desire of the mine operators to incorporate all possible safe-guards in the storage of explosives, including a careful choice of location and arrangement in the plan of the magazine.

Jan 1, 1946

By A. J. Kraemer

For a number of years the Bureau of Mines has conducted semi-annual survey to determine the changes in the characteristics of the rotor gasoline being sold in the United States. Certain cities have been decided upon as points of origin of samples. Tare choice of these cities has been governed by their situation as the representative of a more or less definitely bounded marketing territory. Samples have been taken on or about the fifteenth day of January and July of each year. In the collection of the samples an attempt has been made to get a representation of the important types of motor fuel being sold, and also to tame into consideration the proportion of tie total consumption that is supplied by the different marketers. It is therefore felt that the survey affords a reliable indication of the quality of the gasoline being sold throughout the United States at the time of sampling. The figures in Table I, below, were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points, and the 1C per cent having the lowest end points were averaged. These averages are represented in the table as the "Maximum 10 per cent" and the "Minimum 10 per cent", respectively. The same scheme was used in the succeeding surveys.

Jan 1, 1925

By Arthur L. Murray

"While serving as surgeon with rescue car No 11 of the U. S. Bureau of Mines, the writer visited the principal metal-mining camps of Utah during the latter part of 1919. In visiting the mines, meeting and conversing with miners, and talking over the medical situation with physicians in the various camps, the number of cases of lead poisoning encountered was great enough to attract attention.With a view to procuring more definite information as to the number and distribution of cases of lead poisoning throughout the State, a study of the records of the State Board of Health was undertaken. Utah had no ordinance re¬quiring the reporting of occupational diseases, so it was not possible to secure data an cases A study of the mortality records by years gave the following results.:Year Deaths from lead poisoning.1910,11911,01912,21913,11914,61915,41916,11917,31918,11919,2These few deaths would seem to indicate a fairly low case rate, but when it is realized that lead poisoning is rarely an immediate cause of death and that the train of sequelae in this disease frequently leads to chronic involvemeets of the digestive, nervous, circulatory or genito-urinary systems, it is apparent that the number of deaths showing lead poisoning as the cause can not be taken as an index of the cases prevalent. The time elapsing between the presence of the active signs of lead poisoning and the terminal illness from pathologic conditions excited by lead absorption may be years, and the initial cause, lead poisoning, is frequently lost sight if entirely, hence the death certificate shows no evidence of the primary cause."

Aug 1, 1921

By Perry G. Cotter

The objective of this investigation was to synthesize and investigate the properties of a high-temperature refractory material based on a combination of boron, silica, and magnesium. A magnesium-thermic reaction was used for the synthesis. X-ray examination of the product indicates that the crystalline portion of the composition is a combination of magnesium borides, magnesium silicate, and magnesium orthoborate. Chemical analysis of a representative sample shows, in weight-percent, boron 17.6, silicon 23.9, magnesium 17.8, and chromium 0.5. The balance is largely oxygen. The composition is resistant to high temperatures under oxidizing conditions and is stable in water, hydrochloric acid, and hydrogen. It has a low density (less than 3 grams per cubic centimeter) and a hardness value in the range of quartz. It has a melting point above 1,700° C. and can be hot-pressed to shape in the temperature range between 1,200° and 1,350° C. The properties described in this paper indicate that the material may have some uses as a high-temperature refractory, and because of its boron content it may have some value as a thermal-neutron-absorption material.

Jan 1, 1961

By E. P. Youngman

The mining laws referred to by those who furnished the reports mentioned in the preceding paragraph are : General Austrian Mining Law of 1854 and the Law of 1868 , which prescribes for Hungary (as well as for Transylvania ) the full text and decisions of the General Austrian Mining Law; Government Decree 18346 , 1859 ; Parliamentary Decree of 1861 ; the Law of 1871 ; the Commercial Code , Law 37 of 1875 ; the Industrial Lar of 1884 ; the Law of 1386 ; the Decree of the High Court of Justice , 5540 , of 1399 ; Laws 6 and 7 of 1911 ; Law of 1921 ; Laws 23 and 24 of 1922 ; Laws 5 and 21 of 1927 ; and Law 40 of 1928. ( Lev 21 of 1927 and Law 40 of 1928 are labor laws . ) A compilation of the mining laws of Hungary , " Magyar Banya Jog , " or the " Hungarian Mining Law, " was made use of in part . This volume is the second edition of a school textbook , which ras prepared by Dr. Bela Balkay and Dr. Imre Szeoke , and which was published by the Apollo Press ( V. , Sas -utca 13 , Budapest ) in 1909 .

Jun 1, 1931

By H. A. Doerner

The Rare and Precious Metals Station of the U. S. Bureau of Mines has investigated several cases in which widely divergent amounts of molybdenum were reported by a number of custom laboratories to which quartered portions of the same sample had been sent for analysis . On an oxidized lead ore containing considerable vanadium and a little molybdenum , the amount of the latter reported ranged from 3.14 to 0.24 per cent M003 . The high results were due to the fact that vanadium was estimated with , and reported as , molybdenum . When analyzed by the method described in this paper , 0.15 per cent Moog was found, which is a fair agreement with the lowest figure previously reported . In another and more unusual example , a fine- grained rock containing considerable graphite was submitted for analysis . As a white residue could not be obtained by treating this material with acid , several chemists decomposed the ore by a prolonged fusion with soda ash and nitre and leached the melt with hot water in crder to insure the dissolution of any and all the molybdenum present . After precipitating and filtering the silica from the solution , acetic acid , ammonium acetate , and lead acetate were added to precipitate lead molybdate . The solution contained phosphorous derived from the ore , which precipitated as lead phosphate . The latter was mistaken for , and reported as , molybdenum. As two different chemists used essentially the same procedure , their results , although incorrect , checked . Other chemists using different methods found no molybdenum . From these and other instances it is evident that reputable and conscientious assayers may make serious errors in determining molybdenum, and even duplication of results by different chemists does not necessarily insure against error . The elements most likely to cause trouble are vanadium, tungsten, uranium , arsenic , antimony , titanium, tin , phosphorous , and chromium . The precautions necessary to eliminate these and other impurities vary with the type of ore and the method of analysis . Most texts present methods of limited application and omit or fail to emphasize adequately such precautions . No one method can be given that will best fit every case , but the following procedure has been selected as being the simplest reliable method for such occasional determinations of molybdenum in an ore as are encountered in customs work.

Sep 1, 1930

By H. H. Schrenk

"One phase of the Bureau of Mines' work in the field of health and safety is the promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To promote the development of such devices the Bureau has established schedules of minimum requirements for oxygen breathing apparatus3/ gas masks/, supplied-air respirators5/ (hose masks, airline respirators, and abrasive blasting helmets, hoods, or masks), and mechanical-filter respirators6/.Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules.As a prerequisite to such submittal, the Bureau requires a statement that the device is completely developed and of the design and material the manufacturer believes suitable for a finished marketable device; that the device has been subjected to inspections and tests such as described in the schedules, and that it met those requirements when tested by the manufacturer or his testing agency; and a. statement regarding the nature, adequacy, and continuity of control of the quality of the respirator. If the manufacturer can satisfy these requirements, and if the device, when tested by the Bureau, meets its requirements, a certificate of approval is granted by the Bureau of Mines. The approved devices bear distinguishing marks that indicate that they have been approved, the purpose for which they are approved, and the limitations of their use. If it is found at any time that approved devices purchased in the oven market and tested do not meet the requirements of the schedule, the Bureau may rescind that approval. Lists7/ of approved devices are published periodically for the convenient information of the public.Respiratory equipment may be divided into two main groups: (1). Those that afford protection by removing atmospheric contaminants and (2) those by which a respirable atmosphere from an uncontaminated source is supplied to the wearer.The devices that protect by the removal of contaminants may be divided into two subgroups: (1) Those that protect against gaseous contaminants and (2) those that protect against particulate matter. There may, of course, be combinations of these two.The devices by which a respirable atmosphere is furnished to the wearer also may be divided into two subgroups: (1) The self-contained type, by which the supply of oxygen, or material from which the oxygen can be generated is carried by the wearer, and (2) the hose type, by which air is supplied to the wearer through a hose or tube."

Sep 1, 1939

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.

By J. T. McCartney

"INTRODUCTION The surface areas of the finest fractions of a pulverized material are disproportionately larger than their weights. For instance, Pesrott and Kinney 3/ showed that, in a sample of minus 200-mesh coal, particles that are about 2 microns in diameter represent 15 percent of the entire surface area but only 1.5 percent of the total weight. Because the sur- face area is the dominating factor in the behavior of finely divided materials in many practical processes, the role of the finest particles is of great importance. The oxidation and combustion of pulverized coal, both in the dry form and in suspension in oils, and the hydrogenation to fluid hydrocarbons of mixtures of pulverized coal and heavy oil are reactions in which the surface area of the coal particles has considerable influence. This investigation of the size distribution of fine coal particles was conducted with the hope that such processes would thereby be better understood. The results should also be of value in the study of the crushing and fracture of coal."

Sep 1, 1945

By D. Harrington

Examination of numberous disasters , such as fires or explosions , and the evidence at coroner's inquests following such disasters in several States , have shown the writer how frequently men in charge of the operation and safety of mines have forgotten, or have failed to learn , details of safe mining practices , After securing a position of trust as superintendent , or a certificate of competency to act as shot -firer , fire boss , or mine foreman, some men seem to have felt it unnecessary to keep safety principles in mind , or to keep abreast of current progress in safety ; they have concentrated on getting out maximum tonnage at minimum cost . • In coroner's inquests , the testimony after disasters has shown that firebosses , foreman , and coal -mine superintendents are noticeably lacking in knowledge of the provisions of the State mining law relating to fans or doors , frequency of crosscuts , nature of stoppings necessary , electrical equipment , records of daily mine examinations , quantity of air required , or splitting and overcasting .

Jul 1, 1922

By Eugene T. Sheridan

This circular presents data on individual plants of the fuel-briquet and packaged-fuel industries that responded to the Bureau of Mines annual economic survey and reported production for 1959. The companies named herein represent virtually all producers of processed fuels of mineral origin. A few small companies may not have been canvassed or failed to respond, however, as some plants operate intermittently, and the survey is voluntary. No consideration was given to size of the plant and all plants that reported commercial production were included. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, fabricated from fine-sized mineral fuels by mixing with binders and compressing into small individual shapes. Briquets usually are produced as small, pillow-shaped pieces, 2 to 4 inches long, weighing 2 to 4 ounces. Packaged fuel consists of 3- to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. The overall size of a popular package is 10-112 x 7 x 3-1/2 inches. Briquets are durable, may be stored outdoors, and shipped and used as bulk fuel. Packaged fuel is fragile, and must be stored indoors to keep it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times as a supplement to other fuels. Package fuel is burned without removing the paper and referred to as the "white-glove" fuel.

Jan 1, 1960

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.