Search Documents

By Robert L. Jones, Clifford Dunham

"INTRODUCTION The Wah Wah mine was examined 3/ by the Bureau of Mines in September, and a project was started in November 1942. Assistance was given by the Federal Geological Survey in formulating proposals and plans, and two geoloists were assigned to map the surface and underground workings in October 1942.HISTORYThe Pine Grove mining district was organized in 1S73, but no work was done there until it was reorganized in 1879, after which it is reported that a little ore was shipped. The Wah Wah Mining Co. was incorporated September 2, 1937. Prior to that time, predecessor organizations had spent approximately $122,000 on the property now held by this company. The board of directors of the Wah Wah Mining Co. approved expenditure of $47,652.14 from September 1937 to June 1942 for development. This work was confined to the Tasso shaft and connecting levels. Shipments in 1939 amounted to 925.789 dry tons with a gross value of $12,477.83. This ore contained 20,130 pounds lead, 1,390 pounds copper, 7,434 ounces silver, and 65.09 ounces gold. The mine was idle from July 1941 to November 1942, when, the Bureau initiated a project to unwater the Tasso shaft and proceed with the exploratory work as outlined in the War Minerals Report."

Apr 1, 1946

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By Miles B. Royert

Crude Minnesota taconite was charged in the Bureau of Mines experimental blast furnace so that smelting characteristics of such highly siliceous raw materials could be studied and smelting costs compared with those of a standard Mesabi ore. The Bureau recognized that the highly siliceous nature of the crude ore and its relatively low metallic content would be serious economic deterrents to commercial use of the raw taconite, but compensating factors would be low capital investment in production facilities, large tonnage available on short notice, high recoveries of iron, and low delivered cost. Crude taconite smelted readily in the experimental blast furnace. Coke consumption per ton of metallic product was very high, compared with the average established requirements for smelting normal grades of metalliferous raw materials. Slag rates were also inordinately high. Metal quality was erratic as to silicon, and sulfur contents were objectionably high.

Jan 1, 1961

By Jerry W. Ramsey

The Bureau of Mines examined a low-, a medium-, and a high-volatile Pennsylvania anthracite by densimetric methods using four mesh si.s of each anthracite. Using high-pressure mercury the macropore volumes and distributions of these pore volumes determined, densities in mercury were calculated, and specific pore vo1.r. ware obtained from these mercury densities in conjunction with helium densities. The helium densities were also used with the ultimate analyses of these anthracites in calculating structural parameters by statistical densimetric methods. The effect of 106 or 108 rads of gamma irradiation in the presence of air and in vacuum upon the properties studied with two mesh sizes of each anthracite. Results of the statistical densimetric method seem to show some breakdown of condensed ring structural units at the lower irradiation level, with subsequent polymerization at the longer period of gamma irradiation. The structural parameters obtained also indicated that in going from high- to low-volatile anthracite, either the number of condensed rings per structural unit increased, or the degree of polymerization increased.

Jan 1, 1965

In 2007, a total of 4,639 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 31.2% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,051; 44.2%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=373; 8.0%), followed by Texas (n=352; 7.6%).

Aug 1, 2009

By Stephen A. Swan

Certain types of mobile surface mining equipment are required to be equipped with rollover protective structures (ROPS) capable of protecting the operator in case of a rollover accident. The Bureau of Mines has developed ROPS performance criteria for wheeled front-end loaders. This report reviews the development of rollover test procedures and subsequent testing of ROPS for 52,000-, 286,000-, and 390,000-lb gross vehicle weight (GVW) loaders. The program consisted of both dynamic (roll) and static tests to assist in the development of the ROPS performance criteria. Each test included extensive instrumentation and photographic documentation to fully evaluate the performance of the ROPS. Data summarizing side, longitudinal, and vertical force and deflections are included. The data indicate that for loaders in excess of 240,000 lb, GVW, a side force-to-mass ratio of 1.0 and an energy-to-mass ratio of 6.0 appear to be adequate criteria to protect an operator in the event of a 5400 rollover. For smaller machines, Society of Automotive Engineers (SAE) 11040 performance criteria provide adequate protection. Longitudinal loading, though not ad-dressed in previous ROPS performance criteria, was shown to be a potentially significant factor in ROPS failure. Longitudinal loading and energy criteria equal to 80 pct of side loading criteria are recommended.

Jan 1, 1988

By Albert F. Baker

Techniques were developed and circuitry was assembled for measuring the total and volume resistances to the flow of electric current through solid specimens of anthracite. The two-, three-, and four-terminal test methods demonstrated the extreme sensitivity of resistivity to differences in anthracite characteristics and showed response to changes resulting from variations in structure, temperature, and moisture content.

Jan 1, 1966

By J. J. Forbes

The Act of Congress authorizing the establishment of the United States Bureau of Mines became effective July 1, 1910. One of the most important duties Congress delegated to the Bureau in this Act was the study of health and safety conditions in the mineral industries. Early investigations of these conditions revealed the need of prompt Care of injured employees, as, under the difficulties inherent in their occupation, seemingly unimportant wounds if not treated promptly might become infected and cause permanent disability or even death. Many seriously injured persons brought out of mines and plants by fellow workers ignorant of approved methods of giving first aid or of safe means of transportation have been caused suffering and have had injuries accentuated to such a degree as to bring about permanent disability or death. The need of general instruction in first aid thus became apparent. BRIEF HISTORY OF FIRST-AID WORK The education of miners in the United States in first aid probably was conducted systematically first by the anthracite industry in Pennsylvania. Subsequently, first-aid training was carried on actively in Alabama and Indiana. Meanwhile, a general training campaign was carried on among industrial workers by the American Red Cross Society; when the Bureau of Mines began its nation-wide campaign of instructing employees of the mineral industries, the Red Cross turned over that part of its industrial training work to the Bureau but continued to cooperate by furnishing surgeons as judges in important first-aid contests and demonstr tions and assisted for a number of years in determining training methods.

Jan 1, 1937

By Roger J. Morrell

Disk-cutter experiments were performed on five rock types ranging in compressive strength from 9,000 psi to 27,000 psi. A specially constructed testing machine called a linear-cutter apparatus (LCA) was designed to load and traverse a free-rolling disk cutter across a sawed rock surface. The LCA was instrumented to measure the vertical and horizontal forces acting on the cutter during the run.. The ability of disk cutters to fragment rock was determined for both 60--degree and 90-degree cutting-edge angles, and relationships and regression equations were developed to predict cutter performance based on rock physical properties and applied forces,

Jan 1, 1970

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By W. W. Adams

"A recent paper prepared by the writer summarized the results of an analysis of the accident records of 34 metal mines for the calendar year 1925. The present paper summarizes the results of a similar analysis of the accident records of 59 coal mines for the same year. This summary is based upon reports furnished to the Bureau of Mines, Department of Commerce, by operating companies that par¬ticipated in the National Safety Competition of 1925.The purpose of the Competition was to establish the lowest accident-severity rate, thus showing the smallest loss of time from accidents in proportion to total number of man-hours worked. The reports covered all lost-time accidents that occurred during the year, that is, all accidents that disabled an employee beyond the day or shift on which the accident occurred. Detailed information for each of the 59 coal mines is given in the appended table. Each mine employed at least fifty men underground; over half of than employed more than 200 men underground. Hence the accident records should be typical of those of large-scale mining operations in general where the company is devoting special attention to accident-prevention work. The mines covered by the reports are situated in eleven States: Alabama, Illinois, Indiana, Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Utah, Washington, and West Virginia.A tabulation of the reports covering the 59 mines showed an accident-frequency rate of 123 per million hours of ""exposure* and an accident-severity rate of 10.214 per thousand hours of exposure3. The total volume of exposure or employment was 29,117,561 hours, representing the equivalent of work of 12,000 men for three hundred 8-hour shifts. The records covered employment and accident above ground as well as underground, although they did not include stripping or open-pit mining. Accidents during the year resulted in 33 deaths, 1 permanent total disability, 28 permanent partial disabilities, and 3,510 temporary injuries. These accidents represented a loss of tine equal to 297,417 man days. In arriving at this lost-time equivalent, each fatality and permanent total disability was weighted at 6,000 lost days (see footnote 3), as specified in the scale adopted by the International Association of Industrial Accident Boards and Commissions; permanent partial disabilities were weighted according to nature of injury, in accordance with the scale adopted by the :Board; temporary injuries were weighted according to the actual number of calendar days during which the employee was incapacitated as a result of the injury."

Nov 1, 1926

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By D. W. Boley

This report contains the results of an analysis of the Logan oilfield, Hocking County, Ohio, and predicts the recovery of oil from the Clinton sand by waterflooding. Core analyses, electrical and radioactivity well-survey logs, reservoir-fluid analysis, and geologic and production data were used for this study. Considered in the evaluation were the reservoir geometry, depth, lithology, continuity of the rock properties, fluid saturations, fluid characteristics, rock wettability, and relative permeability-fluid saturation relationships. The study indicates that a properly engineered waterflood should recover approximately 135 barrels per acre-foot of effective sand. The predicted recovery warrants the initiation of a pilot waterflood in this field.

Jan 1, 1965

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By R. Wiebe

During a recent investigation the authors were interested in determining: (1) How many points were necessary to locate the deviation curve for copper-constantan thermocouples within an accuracy of about 0.05° C., used in connection with the, "standard" thermocouple of L. H. Adams (2) Whether copper-constantan thermocouples showing considerable deviations from the "standard" were consistent throughout their calibration. (3) How reliable the extrapolated portion is - that is, the interval between -183 and -220° C. of the "standard" thermocouple.

Jan 1, 1931

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

By Raymond B. Ladoo

Garnets are usually found well crystallized in the cubic system , the principal forms being rhombic dodecahedrons , tetragonal trisoctahedrons or combinations of the two , and hexoctahedrons . They also occur as rounded disseminated glassy grains and in compact massive , laminated or gramlar aggregates . They vary greatly in color , but the most common garnets , almandite and andradite , are most often found of a dark red or reddish brown color .

Apr 1, 1922

By Raymond B. Ladoo

Toward the end of 1920 , the average grades of ground feldspar offered to the pottery industry were so poor and so generally unsatisfactory that many of the largest consumers decided to take active steps for their own protection . A few of the potters made arrangements to grind their own feldspar , while others asked the Bureau of Mines to make a detailed study of the problem and to suggest methods of improvement . Accordingly such a study was undertaken, the partial results of which are outlined in this preliminary report . The outstanding features of the present feldspar industry which are of interest in this connection are stated below. (1 ) Many grinding companies do not own or control all or even a major part of their sources of crude material , but buy in job lots from many sources . (2 ) There is great need of more adequate engineering and chemical control over mines and mills . ( 3) ~ Out of date , inefficient methods and equipment for mining and grinding are in common use . (4) Little or no cooperation exists between feldspar producers , but on the contrary many feldspar companies are exceedingly secretive . This tends towards (a) preservation of obsolete methods ; ( b ) want of knowledge of the essential features of production , market requirements , and the relation between total milling and consuming capacities of the country; ( c ) inefficient and often mistaken trade practices ; ( d) unprofitable and even ruinous competition in dull periods . (5) The small size of many feldspar deposits precludes maintenance of an efficient organization at each individual mine . ( 6 ) Many of the best deposits of feldspar situated close to railroads are becoming depleted , which results in gradual lowering of grades , and increase in cost for better grades . (7) There is a lack of exact mowledge of the ceramic properties and behaviour of feldspar by some consumers , which results in ( a) purchase of feldspar on the basis of price alone , thus encouraging low production costs at the expense of quality , and ( b) inefficient and expensive cross- hauling of both crude and ground feldspar .

Jan 1, 1922

By A. L. Engel

In the period of 1942-1945, medium-grade, oxidized, lead-silver ore was mined and shipped from the Diamond district near Eureka, Nev. An encouraging tonnage of low-grade ore was developed during these operations and partly blocked-out for future mining. If the low-grade ore could be treated profitably, further development of the district would result, and production of an important strategic metal might be increased. A representative sample of Diamond district ore was obtained through the Reno office of the Mining Division for the studies described in this report. The sample consisted of lumps and fines of a highly altered siliceous rock containing much earthy red hematite and some granular black hematite. Examination with the binocular microscope showed the lead carbonate mineral, cerussite, in seams and disseminated in the hematite. No zinc or silver minerals were identified, and no sulfide minerals were present. Analyses of the ore showed:

Jan 1, 1951