Search Documents

By R. R. Faddick

A mineral slurry data hank has been compiled, containing slurry pipelining data on sixteen ores, concentrates, and tailings. The data bank it in the form of a computer print-out all they necessary system constants and headloss data for each mineral commodity. The purpose of the data bank was to assist in the development of a universal head loss correlation for mineral slurries, if such a thing exists. Present headloss correlations were tested and found to be inconsistent for the various mineral slurries. Consequently, a different approach was taken, that of compiling a library or Stanton diagrams relating friction factor and Reynolds numbers for a given slurry in a given pipe diameter. The advantages of the diagrams arc demonstrated and discussed. While this correlation shows excellent potential, it is necessary that additional work, both theoretical and experimental, be performed. In addition, two equations are given from which a design velocity may be obtained to minimize deposition or formation of bedload. The equations are based on data taken from the mineral slurry data bank.

Jan 1, 1972

By Thomas Fraser, William L. Crentz

"INTRODUCTION Sulfur is a most damaging impurity in many of our American coals. From the older coal industry of Europe and Britain we can apparently learn but little about the problem of preparing and using high-sulfur coal. Although washing has long been established there for controlling ash content, sulfur is referred to rarely, as the important deposits are singularly low in sulfur.On the other hand, widely distributed coal deposits of America differ tremendously in sulfur content. Many of the more extensive beds contain too much sulfur for metallurgical use, and almost everywhere except in the Rocky Mountain and Pacific coast regions sulfur control is at least a potential problem. American coal-preparation engineers are confronted not only with great variations in the total quantity of sulfur in coal but with an intricately varying pattern of the physical and chemical forms in which the sulfur occurs. It must be conceded that the baffling problem of sulfur reduction in coal is as yet substantially unsolved, for there are but few isolated instances in which we have been able to prepare a satisfactory metallurgical fuel from coals containing as much as 2.0 percent sulfur in the raw state.It has been assumed generally that organic sulfur, being chemically combined with carbonaceous matter, is distributed throughout the coal matter and that it remains unchanged in the clean-coal part of the product during washing.Sulfur that may be washed out of the coal is that part that is combined with the iron in pyrite lenticles associated with the coal. In most of our coals it has been found that, besides the visible bands, lenses, and flakes of pyrite, extremely small and even microscopic particles of pyrite 4/ are distributed through the coal matter. Only the free, relatively coarse pyrite particles .are removed by conventional coal-washing devices, and usually most of the sulfur is still left in the product."

Dec 1, 1947

By R. Hogg, S. Chander

"The distribution of the wettability of coals of different rank was determined by measurements of contact angles for individual particles. The contact angle was estimated from the equilibrium partitioning of a particle at the water/air interface. Using this technique contact angles were determined for a larger number of particles from a given sample and a frequency distribution of contact angle was obtained. The contact angle distribution was broad for all the coals tested with included an anthracite, a hvA bituminous and a sub-bituminous coal. In comparison, spherical particles of polymethylmethacrylaie gave a much narrower distribution. The distribution for irregular polyethylene particles was somewhat broader than that for the polymethylmethacrylate spheres but broader than that for the polymethylmethacrylate spheres but considerably narrower than that for coal. The broader wetting distribution for coal was attributed to differences in surface chemical properties.INTRODUCTIONA knowledge of the wetting properties of coals is very useful in coal cleaning by flotation and other processes in which separations are based on differential surface properties. The various methods available for measuring wetting characteristics include: contact angle, 1-2 time, time, 3-5 bubble attachment, 6 film flotation,7 displacement pressure, 8-9 penetration rate, 10-11 bubble pick-up, 12 induction time, 13 imbibition time, 14 and calorimetry. 15-16 Of all these methods, however, the measure¬ment of contact angle by the sessile drop and captive bubble techniques have been most widely used. Brady and Gauger"" demonstrated through the use of the contact angle method that the natural hydrophobicity of coal varied greatly from sample to sample. Subsequent experiments showed that this difference correlated well with rank, the larger contact angles generally being associated with the higher rank coals. 18-19 More recent studies by Aplan and co-workers' show that the wettability of various ranks of coals as determined by sessile drop and captive bubble methods is a more complex function of rank. The hydrophobicity of coal usually increases with rank up to about 80% fixed carbon (dmmf) and then decreases."

Mar 1, 1992

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By Benjamin W. Haynes

Analytical procedures are described for the quantitative determination of 16 elements (As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn) and 7 ionic species (NH4, C032-, CI-, F-, NO3-, P043-, SO42-), identification of major and minor mineral components, and measurement of physical properties associated with manganese nodules and nodule processing reject waste materials. Compound identification methods discussed include X-ray diffraction, infrared spectroscopy, scanning and transmission electron microscopy, selective area electron diffraction, and optical and reflected light microscopy. Methods for elemental analysis include atomic absorption spectrophotometry, inductively coupled plasma emission spectroscopy, neutron activation analysis, fluorescent X-ray spectrography, and ion chromatography. Thermal gravimetric analysis, ultraviolet-visible spectrophotometry, ion specific electrodes, and standard wet chemical procedures are briefly discussed. Physical properties determined in manganese nodule materials include grain size distribution, specific gravity, triaxial shear, permeability, maximum density, Atterberg limits, and slurry density. The results of a round-robin analysis of an ammonia process waste material and manganese nodule standards demonstrate the applicability of the discussed methods. Tests discussed for the evaluation of the waste materials for disposal options include the Environmental Protection Agency (EPA) EP toxicity test, the ASTM shake extraction test, and the U.S. Army Corps of Engineers EPA seawater elutriant test.

Jan 1, 1983

By R. L. Rock

The Bureau of Mines conducted radiation-ventilation studies in six large underground uranium mines to investigate the extent of radon-daughter exposure experienced by the miners and to analyze the ventilation systems to set what changes were required to achieve recommended radiation standards. The studies entailed tracing and measuring the mines' ventilating air, quantitatively and qualitaitively, from its entrance into the mines, through production areas, and lack to the surface. Pressures consumed in creating airflow through mine circuits were determined by altimeter surveys. Air quantities were measured with anemometers or by chemical smoke cloud methods. Air quantities delivered through tubing were determined using U-tube water gages to magnahelic gages to measure velocity pressures. Radon-daughters were filtered from mine air to measure alpha activity; activity levels were converted to "working levels," the established unit for reporting miner exposure. Attention was given to locating unnecessary contamination influx sources and recirculating air. The radiation-ventilation surveys showed that where basic principles of food ventilation were not followed, high alpha radiation levels invariably resulted. Some mines required more primary air for controlling radiation levels throughout active areas, but more efficient use of available air was generally possible. Premature contamination of intake air was prevalent where development Openings intersected ore or passed by worked-out stopes. Several auxiliary systems were inefficient in secondary distribution, recirculating air already too highly contaminated for ventilation. Many got these common problems can be traced try the lack of dine planning with radiation control in mind.

Jan 1, 1969

As part of its regular program to provide timely information on domestic mineral commodities, the Bureau of Mines conducted an engineering appraisal of more than 1,300 lode and placer gold deposits in the United States to deter-mine their gold production potential. While these deposits were estimated to contain over 400 million ounces of gold, only 9 million ounces, or slightly more than 2 percent, was found to be producible at $35 per ounce under prevailing mining and metallurgical technologies. The study revealed that any significant increase in available gold in the United States is most likely to come from the discovery of new sources, intensive exploration and development of the more promising known mineralized areas, and development of new or improved mining and metallurgical techniques.

Jan 1, 1967

By R. G. Knickerbocker

[The Electromet l'.ur.::ic'l.l LC:tt:n~ to:!'"' of' the BUl~6au 0: M_nes, Boulder City, ..rev. I invest~.f-'8tes th~ r.: nc= I (l.op itr. in tr.e redon around Boulder Dam, and thi" p2pe:.. ., 'est.3nttl t rt") d.c-velo !l'\CtltR of n seriAl of studies on "Joron uineral~ mario n.~ t~l"'t f1tn.: ... o]

Jan 1, 1940

By E. L. Burwell

Preliminary results of an in situ oil shale retorting experiment conducted by the Bureau of Mines in a shallow bed of Green River oil shale at Rock Springs, Sweetwater County, Wyo., are described. Eleven wells were drilled into a 20-ft-thick section of the shale lying between 68 and 88 It deep, and attempts were made to connect the wells through the shale with a fracture system created by application of high-voltage electricity (electro-linking), hydraulic fracturing, and explosive fracturing. Ignition of the shale through the central well was easily achieved with a propane burner, and shale oil began to collect in three wells within 3 hours. Propane injection was discontinued after 7 days, and combustion continues, although attempts to control the direction of the combustion front have been unsuccessful. Production rates as high as 4 ½ barrels of nil per day have been recorded, but too little is known about underground conditions to permit an estimate of recovery efficiency at this time.

Jan 1, 1969

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Diesel-powered locomotives designed specifically for underground operation were used in the construction of some of the tunnels that comprise the Delaware Aqueduct in New York State. Before this there had been limited use of Diesel-powered equipment such as trucks, bulldozers, and shovels in tunnel construction in various parts of the country, but this equipment was used without modification for underground use and, in some instances, appar¬ently without due consideration of the hazards that might be created by the introduction of fuel-burning equipment into confined underground spaces.As certain definite advantages were apparent if Diesel haulage could be used in tunnel construction in some sections of the Aqueduct, the contractors who were to construct the tunnels in these sections were desirous of using, this type of haulage equipment if it could be used with safety. This matter was given careful consideration by the various agencies concerned with the establishment of safe practices on the Aqueduct project before tunnel driving was started. Of chief concern were the quantities of toxic or objectionable materials that would be discharged into the tunnel air by the exhaust of the locomotives and the volume of ventilating air that would be required to dilute these exhaust gas products to concentrations permissible in the atmosphere of working places."

Jan 1, 1947

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009

By James J. Jessop, Richard E. Thill, Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 1992

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By Warren Hastings

This paper describes the methods and costs, in units of labor end materials, of sinking a 7 compartment vertical shaft 1,261 feet through a fractured, water-saturated formation. The shaft, designed for hoisting 2,500 tons a day, is at Friedensville, Lehigh County, Pa., approximately 6 miles south of Allentown and Bethlehem. It was sunk by the E. J. Longyear Co. under contract to the New Jersey Zinc Co. Preparation for shaft sinking W8A begun July 1, 1947, and sinking was completed August 18, 1952. A total of 604,858 man hours was required to sink the shaft.

Jan 1, 1954

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By John C. Machisak

INJURY data and experience, with related employment statistics, at coal mines in the United States for 1958 are presented in this publication under the following general sections: (A) General injury experience: Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location. (B) Selected injury experience: Tables 7 to 38: Current data on principal agencies of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience by States: Tables 39 to 43: Current data on injuries, their causes, rates of occurrence and severity; employment and production data by work location, by States. (D) Major disasters: Table 44: Data on major disasters from 1949 to 1958. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 45 to 49: Data on fatalities and their causes at bituminous coal, lignite, and anthracite mines from the earliest records through 1958.

Jan 1, 1961

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989

By Engelmann. William H.

In pursuit of innovative methods to improve mining productivity, the Bureau of Mines is investigating the use of inorganic salts as drilling fluid additives for penetration enhancement. Laboratory diamond drilling tests were performed on Westerly Granite with aluminum chloride solutions and on Sioux Quartzite with aluminum nitrate and aluminum, calcium, sodium, and zirconium chloride solutions as drilling fluid additives. These drilling results were compared with the average drilling performance using distilled, deionized water on Sioux Quartzite (12 replicate tests) and Westerly Granite (3 replicate tests). Maximum in-creases in penetration per given time and bit life were obtained when drilling with zero point of charge (ZPC) concentration solutions of each additive. For Sioux Quartzite, maximum increases in penetration and bit life ranged from 96 to 115 pct and 64 to 99 pct, respectively. For Westerly Granite, maximum increases in penetration of 155 and 165 pct and bit life of 109 and 136 pct were obtained at or near ZPC aluminum chloride concentrations of quartz (7.3 x 10-7 mol/L AIC13) and alkali feldspars (1.1 to 1.5 x 10-6 mol/L AIC13), respectively. This simultaneous increase in penetration per time together with extended bit life should result in increased productivity and reduced bit costs.

Jan 1, 1987

By L. M. Demers, D. C. Kuhn

"Kuhn, Douglas C., and Laurence M. Demers. Effect of surfactant on basal and silica-induced eicosanoid production by the alveolar macrophage. Am. J . Physiol. 269 (Lung Cell. Mol. Physiol. 13): L165-Ll 70, 1995.-Infiammation and fibrosis subsequent to the inhalation of certain mineral dust particles has been suggested to result from the activation of eicosanoid synthesis by the alveolar macrophage (AM). To determine if surfactant modifies dust-induced generation of eicosanoids by the AM, we evaluated the effect of the surfactant lipid dipalmitoyl lecithin (DPL) on the production of eicosanoids by rat AM exposed to respirable silica dust in vitro. During the first 24-h exposure period, DPL alone significantly increased basal production of eicosanoids but completely inhibited silica-induced thromboxane A2 synthesis. In contrast, leukotriene B4 (LTB4 ) production was only partially reduced by DPL. During a second 24-h exposure period, LTB4 production in response to the highest dose of silica remained significantly elevated in the presence of DPL. Similar results were obtained when the surfactant preparation Survanta was evaluated. These results suggest that 1 ) DPL and Survanta independently activate AM eicosanoid production, 2) DPL and Survanta modulate the response of the AM to silica dust, and 3) L TB4 may be the most important eicosanoid mediator of the long-term effects of silica dust exposure on lung pathophysiology. THE OXYGENATED METABOLITES of arachidonic acid (AA) (here collectively termed eicosanoids) have been implicated as important regulators of lung physiology and are thought to be involved in pathophysiological sequelae such as acute respiratory distress syndrome, asthma, and the pulmonary complications of sepsis (20). This role is manifested through both direct effects on lung physiology as well as through an indirect modulatory effect on the release of other mediators of lung injury, in particular profibrotic cytokines such as the interleukins and tumor necrosis factor (15). Recently, exaggerated eicosanoid production by both the alveolar macrophage (AM) and the type II epithelial cell has been demonstrated to result from the exposure of these cells to several particulates, including crystalline silica (quartz) dust (5, 9, 17). These observations have led to the suggestion that eicosanoids play a major role in the etiology of pneumoconioses.Another secretory component of the pulmonary environment, surfactant, has been shown to modulate crucial AM functions, such as bactericidal activity and the recruitment of circulating immune cells (25). Indeed, an important feature of the lung's reaction to inhaled mineral dust is an increase in surfactant production, perhaps as a compensatory or protective response (1, 16). In addition, the alteration of the surface properties of mineral dust by surfactant or its components has been shown to influence the biochemical response of the AM to the dust, perhaps by altering the surface charge of the dust particle (11, 29, 32). And recently, Wallace et al. (28) have shown that the coating of mineral dust with surfactant, and its subsequent removal by lysosomal phospholipase, unmasks differences in dust cytotoxicity that are not apparent when AM are exposed to uncoated dust. Thus it appears that the inclusion of surfactant in in vitro exposure studies may be important in evaluating both the absolute levels of eicosanoid production by the normal and dust-exposed AM and the temporal relationship between dust exposure and the production of inflammatory mediators by the AM. Therefore, we characterized the effects of the surfactants dipalmitoyl lecithin (DPL; the primary lipid component of natural surfactant) and Survanta (a commercially available surfactant derived from bovine lung) on basal and silica-induced AM eicosanoid production during two 24-h periods after exposure to dust particles to both allow the enzymatic removal of surfactant from the particle surface and evaluate the k"

Dec 1, 1996

By G. V. Sullivan

This report summarizes the results of metallurgical investigations by the Federal Bureau of Mines of manganese oxide ore, averaging 23 to 25 percent manganese, stockpiled at the Butte-Philipsburg depot of General Services Administration (GSA). The oxide ores were stockpiled in two general classifications, straight oxide ore and mixed oxide-carbonate ore. Continuous-circuit flotation tests at the Albany (Oreg.) Metallurgy Research Center of the Bureau of Mines showed that each of these ore types could be concentrated by an oil-emulsion scheme to produce a concentrate that could be sintered to meet program specifications. About 88 percent of the manganese was recovered in the concentrate from the straight oxide sample, with the sintered concentrate containing 48 percent Mn. The sintered concentrate from the mixed oxide-carbonate sample contained 41 percent Mn with a recovery in the concentrate of 95 percent.

Jan 1, 1961