Search Documents

By Gopala N. Krishnan

The most promising candidate for the recovery of alumina from non-bauxitic sources is the leaching of clay by HCL acid followed by crystallization of aluminum chloride hexahydrate (ACH) by hydrogen chloride sparging. Hydrothermal precipitation of boehmite ( ?-A100H) from aluminum chloride solution will simplify the process, will reduce energy consumption and will eliminate corrosion problems involved in calcination of ACH to obtain alumina. This report summarizes the results of Phase I of a program to study the precipitation of boehmite from AlC13 solutions. The amount of boehmite precipitation from dilute A1C13 solutions (5 wt%) is . negligible below 200°C. Above 200°C the precipitation increases with increasing temperature approaching 40% at 300°C. Addition of HCl acid to the dilute A1C13 solution even in small quantities drastically reduces boehmite precipitation. Solution impurities such as Fe, Ca, Mg, or Na substantially promote the precipitation of boehmite. No precipitation is observed from concentrated A1C13 solution (30wt%) representing the leach liquor.

Jan 1, 1980

By R. G. Nelson

This report covers investigations of the Bureau of Mines for the period of June 15, 1952, to June 15, 1953, on a research project for the Materials Laboratory, Wright Patterson Air Force Base, Dayton, Ohio. The primary purpose of this investigation was to make high-purity chromium-base alloys having room-temperature ductility and high-temperature strength. The Nonferrous Metals Branch of the Bureau of Mines, Albany, Oreg., has, during the past 7 years, developed on a laboratory scale a hydrogen treatment method for making high-purity chromium that can be fabricated into thin sheet and wire. This material can be bent at room temperature. The object of this investigation was to use this material to develop improved chromium-rich alloys for high-temperature uses.

Jan 1, 1955

By W. P. Diamond

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development program. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By H. William Zeller

The Bureau of Mines is conducting research to determine whether the use of chemical surfactants improves respirable coal dust control and is evaluating laboratory test criteria for selecting effective surfactants. This publication presents the results from wetting effectiveness tests with emphasis on the capillary rise test. The test variables investigated included coal particle size, type of surfactant, surfactant concentration, test duration, and mineral con-tent of the water. In addition to the rise test, measurements of con-tact angle, zeta potential, and sink time for various coal and surfactant combinations were conducted. No significant correlations among the four wetting tests were observed, a surprising result which implies that each test type measures specific aspects of the wetting phenomenon and also that each test type should only be used to select surfactants for specific applications. For example, the rise test shows solution penetration into porous materials, and the sink test discriminates among surfactants for dispersing finely ground materials into suspension. Another important conclusion is that combinations of agents retain their individual wetting properties, allowing mixtures to be for-mulated to perform well in both rise and sink tests.

Jan 1, 1983

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels'. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner's head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

By Robert E. Wood

The temperature dependency of the low-density viscosity coefficients, ?°T, of helium and of nitrogen, 100° to 1,000° K, is correlated with empirical equations, and the temperature and composition dependencies of the low-density viscosity coefficients, ?°T, of helium-nitrogen mixtures are correlated with the Chapman-Enskog expressions by using the Lennard-Jones (6:12) potential function. The residual viscosity, ?T,P - ?°T (the difference between the viscosity of a compressed gas and the dilute gas at a given temperature), was found to be a function of the thermal pressure coefficient, (?P/?T)V, and two parameters, a and 1, which are characteristic of gas composition. The equation ?T, P = ?°T + a [(?P/?T)V]ß represented 1,340 higher pressure experimental viscosity values with a mean absolute deviation of 0.86 percent, and this equation was used to compute viscosities of the gaseous helium-nitrogen system for a range of temperatures and pressures including those encountered in Bureau of Mines helium purification processes and in a crude-helium conservation gas reservoir. Tabular viscosities for helium, nitrogen, and 13 helium-nitrogen mixtures are presented for 110 temperatures, 133° to 740' K, and 49 pressures in the range 1 to 240 atmospheres. The accuracy of the tabulated viscosities varies because correlation parameters were obtained from experimental data of unequal reliability. It is estimated that uncertainties in the computed viscosity values are ±5 percent for the region 325° to 740° K, ±2 percent for the region 183° to 325° K, and ±5 percent for temperatures below 183° K. The latter uncertainty may rise to y10 percent as critical conditions are approached.

Jan 1, 1970

By Albert W. Cox

This paper, one of a series prepared for the United States Bureau of Mines discussing the methods used in mining, crushing, and grinding materials for cement manufacture, deals particularly with the methods used at the Security plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of, total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scone of the cost tabulations shall ensue.

Jan 1, 1932

By R. H. Storch

"A preliminary examination of the Bi-Metallic molybdenum prospect was made in October 1944, as a result of which it was recommended that a trench exploration project be undertaken on the property. This report presents the information obtained from project work done during June 1945.In its program of exploration of mineral deposits, the Bureau of Lanes has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and. economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, special acknowledgment is due S. H. Lorain, chief, Albany Division, Mining Branch, for aid in preparing the report.The property is situated in the NW1/4, sec. 26, T. 39 N., R. 29 E. about 21 miles northeast of Tonasket. Tonasket (population 643), the nearest town, is a way point on a branch line of the Great Northern Railway. The prospect is reached by a good gravel road through Havillah to Vincent's ranch, about 3 miles northeast of Havillah. From the ranch, an abandoned dirt road extends to the portal of the Moly alit, about 1 mile distant. The mine road could be kept open without difficulty if properly graded and surfaced."

Aug 1, 1946

By Louis H. Berkelhamer

"INTRODUCTION The method of differential thermal analysis suggested by Le Chatelier (1)1 in 1887 has recently emerged as an outstanding means of studying the constitution of various substances, particularly clays, soils, and miscellaneous hydrous materials (2). The literature ably discusses the applications and results obtained but has paid too little attention to specific details of construction of the apparatus. Knowledge of the apparatus is of importance to the experienced research man as is extremely useful to the novice v ho ventures into this field of analysis. Further, it is generally acknowledged that the variations in design and conditions of operation are one of the essential causes for differences in characteristic temperatures as reported by various investigators. A step forward in the elimination of such differences is the publication of the details of construction and operation of a simple and inexpensive apparatus that has proved useful at the southern Experiment station of the Bureau of Mines, where it was used in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jul 1, 1944

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By Frederick C. Trutt

A guide to the development and utilization of an interactive mine-power-system fault program (Z-bus by algorithm) is presented. Theoretical foundations, as well as implementation considerations are discussed with respect to the mine-power system. Alternative Kron reduction techniques are presented along with a triangular-storage method for storage conservation. Program capabilities include the analysis of balanced and unbalanced (line-to-line, line-to-ground, and line-to-line-to-ground) fault situations using symmetrical component theory. To account for phase shifting in delta-wye transformers and zero-sequence network constructions, transformer and load configurations are specified by the user. The positive-and zero-sequence connections needed for network conformity are automatically constructed with the required impedances.

Jan 1, 1979

By Oliver Bowles

A conviction is growing that depressions and other adverse conditions are not entirely unavoidable if a knowledge of past achievements and shortcomings is intelligently, applied in shaping the course of industry. Mineral producers have available a source of such knowledge concerning; their industry in the statistical records of the United States Bureau of Mines, and by scanning, this increasingly exact history can obtain information on which to found a more stable future. This paper contains a brief history, covering more than 50 years, of the activities of the nonmetallic mineral industries as a group, followed by short histories of each of the more important commodities in which are noted the circumstances that lave influenced their development.

Jan 1, 1933

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By Lloyd A. Morley

The performance of electrical grounding systems in open-pit metal mines is evaluated, using techniques which are described thoroughly. The normal electrical distribution and grounding practices used in metallic open-pit mines are reviewed and compared with coal mine usage. The results are used to generate the included recommendations for Federal Regulations concerning open-pit metal mine grounding systems.

Jan 1, 1976

By G. W. Grove, O. V. SIMPSON

During the years 1945, 1946 , 1947 , and up to July 1, 1948, only one death was caused by mine fires in bituminous - coal mines of the United States . The one fatality occurred in an Illinois mine in December 1945, and , therefore, there had been a period of 2-1/2 years in which no deaths occurred as the result of mine fires . Moreover, 1946 was the first year since 1930 in which no deaths occurred from mine fires . This record is markedly better than that of 1944 , when 89 fatalities and great property damage were caused by mine fires in bituminous - coal mines and 16 additional men were killed by an explosion that occurred while they were attempting to seal a mine fire .

Apr 1, 1949

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By H. D. Baylor

This is the first of a series of papers describing mining methods and costs at cement plant quarries throughout the United States and deals directly with those methods employed and costs obtained at the quarry of the Louisville Cement Co. located at Speed, Ind. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Mr. J. M. Buohheit, superintendent of quarries, and Mr. H. E. Schoonover, quarry engineer, in furnishing data and in compiling this report.

Jan 1, 1930

By Richard J. Leary

The inputs of capital and labor to support future iron ore production were developed by the Bureau of Mines from projections of iron demand and estimates of capital and labor requirements. Trends in technologic change and the organization of production were analyzed. Labor requirement schedules for iron ore mining and beneficiating were constructed from aggregate inter-temporal trends and 1970 cross-sectional analysis of mines and mills. A sup-ply schedule of the capital requirement for mine-mill-pellet plants was developed from U.S. and Canadian experience. The structure of demand for iron to the year 2000 was examined as well as the availability of resources. Projections of capital and labor requirements to 2000 were constructed under two international patterns of iron ore supply to the United States. The most likely model is for a continuation of the 70 percent United States-30 percent foreign shares, expanding at an average 2.0 percent growth rate to 2000, and supported by a cumulative gross capital investment of $3.8 billion constant 1967 dollars and a labor force in the United States of 29,800 by 2000. The information content of projections is discussed, and the possible effects of international forces on supply are considered. A generalized methodology for estimating capital and labor requirements in other mineral industries also is included.

Jan 1, 1975

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010