Search Documents

By Robert B. McElwaine

"The demand for barite has increased greatly in the last 10 years, especially during World War II. Depletion of oil reserves and subsequent increase in deep drilling created a heavy demand by the oil industry for barite to be used as drilling mud. The great increase in demand for barite gave impetus to the development of a, deposit of impure barite near, Magnet Cove in Hot Spring County, Ark.The critical condition of the national barite supply early in 1944 led the War Production Board to recommend that the Bureau of Mines attempt to prove the existence of a large reserve tonnage of barite in the Magnet Cove area and arch for new deposits. To carry out this program, the Bureau explored on newly reported. Barite deposits in southern Montgomery County, Ark. The Gap Mountain, Fancy Hill, and Sulphur Mountain barite deposits were investigated. Eight diamond core-drill holes and 1,336 linear feet of surface trenching were completed, and barite samples obtained were analyzed, A study of the Montgomery County barnse district indicates that the lenticular bodies of barite replace a favorable host rock near the base of the Stanley shale formation. Barite is exposed along the side of anticlinal mountains where erosion has truncated the beds on the limbs of the associated synclines. An appreciable amount of barite suitable for commercial use has been indicated by trenching and core drilling. The Gap Mountain and Fancy Hill deposits are controlled by the Magnet Cove Barium Corp. and Baroid Sales Division of National Load Co., respectively. The ore is similar to that of the Magnet Cove area and is amenable to concentration by a flotation process. Mining of these deposits had not been begun by the time the Bureau completed its exploration project."

Nov 1, 1946

By E. J. Lintner

This paper is one of a series being prepared by the Bureau of Mines describing; gypsum mining and crushing methods and costs at various operations throughout the, United States. These papers are designed to dissemminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole; on the other hand, operating costs are essential to the technical discussion and. study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the mining and primary crushing methods employed at the plant of the Ebsary Gypsum Co., Inc., Wheatland, Monroe County, N. Y. This company is capable of maintaining a maximum yearly production of 220,000 tons of crushed gypsum, thereby ranking as one of the largest gypsum operators of the State. The methods and practices employed typify the standard methods followed by gypsum producers in western Now York State, The bed of gypsum mined lies only 35 feet beneath the surface and is above average thickness for this vicinity.

Jan 1, 1937

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

By J. H. Hedges

During the World War Leadville was an important producer of manganese and maganiferous ores for then steel industry. Normally, the market for these ores is limited to the requirements of the local steel mill at Pueblo for low-grade ores used in making, basic pig iron containing 1 to 2 percent Mr and spiegoloison containing 20 percent Mn, but during the war and a brief period of postwar readjustment, a good deal of 25- to 40-percent manganese ore qua shipped to in-stern steel-manufacturing centers. Throughout the active life of the camp, manganiferous iron ore carrying a little silver and lead and sometimes as such as 35 percent Mn was chipped to load smelters for flux. The total reordered production is 936,024 tons of metallurgical ore shinned to steel mills and 2,576,514 tons of fluxing ore, much of it of metallurgical grade.

Jan 1, 1940

These proceedings consist of an overview of the underground metal and nonmetal mina fire protection research currently being conducted by the Bureau of Mines. The following papers address the areas of prompt, reliable fire detection, fire planning and warning, fire suppression, and personnel protection. Selected topics are included here that cover fire protection systems for shafts, underground fueling areas, and mobile underground mining equipment; spontaneous combustion, improved stench, and product-of-combustion fire warning systems; computer-aided ventilation modeling; fire doors; and an investigation of fire hazards in mine timbers. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By Ronald B. Hollenbeck

The value of mineral production in Alabama continued to increase and reached a new high of $260 million, 3 percent above the previous high established in 1967. Record high values were reported for bentonite, crushed marble, lime, miscellaneous clay, portland cement, salt, sand and gravel, and scrap mica. The value of coal, total cement, petroleum, and stone accounted for 87 percent of the State&apos;s total value of mineral production. Alabama ranked second among the States in the production of bauxite and scrap mica and third in kaolin, masonry cement, and native asphalt.

Jan 1, 1970

By B. W. Gandrud

This is the first report published by the Bureau of Mines on washability characteristics of coal from beds in Tennessee. It is based principally upon screen-sizing and float-and-sink tests of raw coal from a bed on the Cumberland Plateau. Stripping operations were undertaken recently on this bed by the Cumberland Collieries, Inc., near Chalybeate,Van Buren County, Tenn. The bed has not been definitely correlated, but it may be an extension of the Sewanee bed, which has been mined extensively in the Tracy City district to the south-vest and at points near Dunlap and Pikeville to the southeast and east. It was spoken of by officials of the Cumberland Collieries as the Sewanee bed at the time of sampling for this study. In a letter dated October 16, 1948, W. D. Hardeman, geologist of the Department of Conservation, Nashville, Tenn., states: "The stripping operations of the Cumberland Collieries near the old postoffice at Chalybeate are, I am fairly certain, in the upper part of the Whitwell shale, which carries the Sewanee coal. This coal may be a stray seam, but it probably can be correlated with the Sewanee coal, which is mined farther east. "There are no detailed geologic maps or reports covering the area, and this opinion is based on what was observed in visiting the strip mines in that general vicinity." The laboratory work upon which this report is based was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the Cumberland Collieries, Inc.

Jan 1, 1949

By S. J. Broderick

[The discovery in 1934 that carbonaceous materials, such as coal, peat, and lignite, when treated with concentrated sulfuric acid, were given cation or bate-exchange properties opened up a field of new materials with many interesting possibilities. These hydrogen exchangers, as they were called, were so superior to the impractical hydrogen exchangers made from natural and synthetic zeolites tat they were accepted immediately by the water-conditioning industry. A noteworthy advantage of the carbonaceous exchangers is that they are nonsiliceous, hence they do not give up silica to the water as do the natural and synthetic Zeolites, especially if the hard water is corrosive. For this reason the new exchangers found immediate favor in boiler-feed-water conditioning.]

Jan 1, 1941

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau&apos;s programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau&apos;s contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Commun¬ications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By BUREAU OF MINES

This report is submitted in accordance with the provisions or une Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1951 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: Oil from Coal. R. I. 4865, Part I - R. I. 4866, Part II - Oil from Oil Shale. Identical in each report, the introduction summarizes research progress made in 1951 under the entire Synthetic Liquid Fuels program. A free copy of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Jul 1, 1952

By L. C. IlsLey

Permissible electric nine lamps are approved with the. understanding that if actively marketed they will be listed in Bureau of Mines publications so that state mine departments, compensation bureaus, mine operators, miners, and others interested in safety equipment for mines may know the permissible lamps available and the important safety features of each. The last list of permissible electric mine lamps was issued as Report of Investigations 33045 in June 1936, a supplement to Bulletin 332.6 All lamps described in Bulletin 332 are either obsolete or have been materially modified, as covered by extensions of the original approvals. These modified lamps and the new designs approved since 1930-totaling 12 cap lamps and 23 lamps of miscellaneous types-comprise the present list of actively marketed permissible electric mine lamps. This bulletin presents the Bureau&apos;s test requirements and procedure relative to permissible electric mine lamps and describes briefly the lamps, giving tabulated details of each.

Jan 1, 1942

By Walter D. Holland

This document is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended to provide above ground metal and nonmetal mining employees with training which will assist them in performing their work safely and healthfully. A document entitled, "Airborne Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas," is used as a manual for the students during the course. The unique features of the teaching guide are thumb rules for recognizing hazardous situations, candidate contamin¬ants for each work area and descriptions of control devices and work procedures.

Jan 1, 1977

By Irving Hartmann, Edward Thomas

"INTRODUCTION Adoption of rubber-tire shuttle cars underground in conjunction with mobile coal-loading machines has introduced new problems in the control of dust on mine roadways. Where this type of loading and transportation is used, development and extraction are generally rapid, with the result that much coal is spilled from the shuttle cars during normal operation, Coal in the roadways from this source and from sloughing of the ribs is ground to fine dust by the wheels of the 'shuttle cars and by the treads of the loading and mining machines. The coal dust usually is somewhat contaminated by pulverized rock, and the mixture could not be loaded with the run-of-mine coal without undue contamination of the product even if it were cleaned up promptly.The presence of large quantities of fine, loose dust, which is constantly stirred up and kept in suspension in air by the traffic, constitutes a grave explosion hazard, reduces visibility along the roadways, and is physiologically harmful to the workmen who breathe the air. From the operating standpoint the loose material is undesirable along the roadways because it provides poor traction for the trucks and thereby increases wear and power consumption. The dust-explosion hazard could be eliminated or reduced by frequent application of sufficient rock dust on the roadbed; but this would not remedy the other difficulties, and in fact it might intensify them. Where practicable, the most direct and effective safety measure is to clean up and remove promptly all dust that forms and settles on the roadways. Unfortunately, in many cases this procedure is not feasible. A third Suggested remedy is to prevent dispersal of the dust into the air and to promote its consolidation on the floor by wetting the dust particles.During the past few years several mines have used calcium chloride on shuttle-car roadways to allay the dust thereon. When exposed to the' humid atmosphere of the mine this salt absorbs Moisture from the air and deliquesces, and in this way wets the dust on the floor of the roadway. In a survey conducted in coal mines in southern West Virginia and in eastern Kentucky where calcium chloride has been in use, somewhat conflicting re- ports were received regarding the merits of the application, and several operators have abandoned the practice either because of actual or assumed disadvantages. The purpose of the study described in this report was to collect and correlate evidence and, on the basis of experimental data obtained in the field and in laboratory tests, to present a clearer picture of the factors involved in the allaying of dust by use of salts."

Sep 1, 1945