Search Documents

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Viktor Aranovich, Thomas E. Brown

The Almalyk Integrated Mining and Metallurgical Plant is located near Tashkant in Uzbekistan and is one of the former Soviet Union's largest copper producers. Almalyk consumes about 10,000 metric tonnes of explosives annually and expects this requirement to double by the end of the century as they implement a program to boost mine output.

Jan 1, 1998

By M. Araos

Non-ideal explosives can be characterised by different methods like velocity of detonation measurement, double pipe tests, underwater tests, aquarium tests, etc., to name a few. Both aquarium and velocity of detonation tests were selected to characterise a non-ideal explosive that is based on hydrogen peroxide, fuel, and void sensitisation. The detonation process in an aquarium of this sensitised explosive was captured at 80,000 frames per second using a high-speed camera. The explosive product was detonated using 51mm (2inches) diameter acrylic pipe charges. The product was detonated at different densities in an aquarium (cube box containing water). An aquarium provides a homogenous confinement for the detonation of explosives and more importantly, allows observing the shock wave as it changes the refraction index of water. The analysis of the video footage allowed the calculation of the velocity of detonation, pressure, gas rate release, and how the shock wave's shape in water changes with densities. It is suggested that the calculation of the rate of gas release could be related to the bubble data obtained from underwater tests.

Jan 1, 2024

By James T. Ludwiczak

Drilling and blasting in a Karst (sinkholes and mud seams) environment has long been a problem for blasters, miners, quarry operators, contractors, and developers. While one cannot change the geological conditions, one can take some measures during the bidding process and the initial preparation of the blasting program to help reduce some of the problems. During the geotechnical investigation and developing the test/core drilling grid, the owner/developer needs to take some additional measures that will provide important data to the blaster to help reduce the problems associated with blasting this type of geology. The owner/developer must also understand that, due to the geologic conditions, the results of the blasting will not be ideal and there may be additional blast-related costs. If provided the proper geologic data, the blaster can develop drilling patterns and blast designs that will help reduce some of the more problematic areas.

Jan 1, 2005

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Tapan Goswami, Brent Geoff

Mining multiple steeply sloping coal seams introduces challenges in terms of safety and productivity. Work on steeply sloping surfaces for the processes of bench preparation, mark-out, drilling, loading and blast tie-up, coal cleaning and recovery is inherently hazardous. Furthermore, a large number of mining cycles is usually necessary, as small rounds are required and each layer is separately drilled, loaded, blasted and excavated. This exposes personnel and machines to additional risks and also incurs higher unit costs of mining as machine productivity is reduced. A case study is presented of a mine in New South Wales, Australia where three coal seams are separated by layers of inter-burden rock. Due to the unfavourable sloping nature of the coal seams the conventional practice was to drill and blast each layer separately.

Jan 1, 2010

By David Cheung, S. Paul Singh

"The characteristics of a blasted muck pile can have a significant effect on the productivity and economyof loading and hauling operations. Poorly fragmented and tight muck piles, caused by insufficientdisplacement of the broken rock, lead to higher digging and hauling costs. Therefore muck pile must be tailored to suit the loading and hauling equipment. In order to achieve this objective, it is imperative to understand the relevant muck pile characteristics and factors governing them. In general, muck pile characteristics are governed by the blast design parameters, rock mass geology, explosive characteristics and post-blasting requirements."

Jan 1, 2017

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Randall M. Wheeler

Computer analyses of single hole signatures are often used to help blasting operators predict the type of ground vibration effects that may be produced from production blasts incorporating various delay intervals. Frequency analyses of single hole waveforms and subsequent multi-hole waveform simulations can allow an operator to determine the best type of delay intervals to use in order to minimize low frequency ground vibrations.

Jan 1, 1989

By Tyler Ross, John Tatom, Lon Lantis

The Institute of Makers of Explosives (IME) began development of a Quantitative Risk Assessment (QRA) tool, IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk), in 2005 as a technology transfer effort with the United States Department of Defense (US DoD). Version 2.0 of the software has been developed over the last two years and introduces many new features and upgrades. Key upgrades include a new map-based user interface, new debris density hazard models, a metric version, and additional user options referred to as “conservatism switches”.

Jan 1, 2014

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By C E. Johnson, S Hosein

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as a consequence of the shock wave created by the detention of the explosive charge in a blast hole. In an attempt to evaluate these hypotheses, an investigation was undertaken over a 4-year period with the aim of determining the precise origin of air overpressure. The research was carried out at a chalk quarry in the North of England.

Jan 1, 2017

By Francisco Sena Leite, Thomas Palangio, Vinicius Miranda

With an increasing pressure to find efficiencies in the mining industry, operations are looking for continuous improvement tools to validate blasting procedures, a crucial and often overlooked area of the process. Using case studies completed at both small and large-scale mining operations, this technical paper proposes a practical methodology for pattern expansion studies, taking into account terrain parameters, rock quality and explosive strength. This technical paper will use a series of tools geared towards an economical continuous improvement procedure, using UAV particle size analysis to optimize blasting based on “generalized reduced gradient” for non-linear problems, with cost savings being the main objective. For the validation of this methodology, one scenario was created based on the operation’s budget: an economical continuous improvement plan that relied on manual data collection methods in order to baseline and optimize procedures.

Jan 1, 2018

By Yeon-Ho Jin, Eui-Haeng Heo, Yun-Seok Park, Sung-Oong Choi, Hyung-Dong Min, Min-Su Jeong, Seung-Joong Lee

As rock fragmentation in bench blasting can affect the following process such as loading, hauling and crushing, its good control is essential for assessment of blasting efficiency and production cost.

Jan 1, 2015

By S. Klerkx, R Battulwar, J Valencia, J Sattarvand, E Emami, M. Soleymani Shishvan

A new technology for energy distribution optimization, supported by NIOSH.

Feb 1, 2020

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lie Company’s new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002