Search Documents

By Bryan Papillon, Karl Christopherson

In order to improve vibrations from quarry blasting, a new technique and timing pattern was established and applied to the particular geology. By shooting a single representative borehole one full second ahead of the production blast, a signature waveform can be isolated and analyzed. Multiple productionsignature blasts were performed. Encroaching residences require quarries to adjust their blasting techniques to reduce vibrations and raise frequencies. A signature hole inherently poses problems to quarries. Blasting one single hole from a production bench poses safety issues to wall stability; vibration issues to close neighbors; and budget issues to the quarry operator. Results showed that the new timing pattern reduced vibrations through timing optimization without a loss in quarry production. Therefore, this technique of vibration analysis employing a production-signature hole is successful in creating a timing pattern that meets the quarry’s goals.

Jan 1, 2008

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By R Mancini, G Borla

This paper analyses the first results of a part of an EEC research project ("Blasting control for underground mining"). This research that involves three universities (Paris, Torino and Leoben) has been carried out at the Eisenerz test mine in Austria. In the experimental campaign here reviewed, parallel holes rounds have been fired "decomposed", which means with enough delay between the explosions of the successive blastholes groups to allow for a separate evaluation of their effects on the rock. The seismic effects have been recorded by geophones placed at small distance from the blast, the aim being to find out correlations between the features of the seismogram and the good or poor performance of the single blastholes, or of the groups pertaining to the same delay. Indeed, the seismogram is the only safe and cheaply obtainable description of what happens during the blast. The seismogram should be transformed in a diagnostic tool in the round 'calibration' stage, and in a routine control device during excavation.

Jan 1, 1995

By H Leonard Mangum, Victor C. Bryan, Dan McCutchen

Recently there has been an unprecedented marketing effort to promote the advantages of various non-electric initiation systems. This activity has probably been influenced by a major manufacturer's decision to discontinue electric detonator production. Subsequently, distributors of explosive materials, rather than introducing new electric detonator brands, are emphasizing the use of existing non-electric systems. In many cases, such methods fill the need of explosive users in the quarry industry. However, the use of any initiation system should be based on performance, rather than the bent of the market or convenience to the supplier. This analysis is an evaluation of the performance of non-electric systems with emphasis on double trunk line and loop (redundant), as compared to precise electric detonators in use by Martin Marietta. Redundant non-electric detonators, even though more costly, offer the most reliable method of non-electric initiation. However, state-of-the-art precise electric detonators give the best overall performance, except in an environment involving extraneous electricity.

Jan 1, 1990

By C M. Deosthale, V N. Pangal, M N. Rao

New Mangalore Port is the most important port in Karnataka State, on the west coast of India on Arabian Sea. It handles export of iron ore, granite, coffee, spices etc and imports of crude oil, fertilizers etc. Since 1991, after economic liberalisation by the Government of India, the exports and imports at this port got a boost. Hence the Port Trust felt the need to increase the draught by about 3 to 5 meters for access to bigger ships. In response to a global tender in 1995, the Dutch Dredging Company got the contract to remove 30,000 cu.m of hard granite bed rock, covering 28,000 sq.mtr. area for the Turning Circle and oil Jetty. The operations of drilling, blasting and dredging were to be carried out to deepen the area to about 15 m draught without affecting the normal trade at the Port. This was a time bound contract to avoid interruption by severe Monsoon rains.

Jan 1, 1999

By D O. Doehring, W A. Charlie, W A. Lewis

The detonation of explosive charges releases large quantities of energy that can produce rock and soil deformations far from the detonation point Extensive data are available on blasting in general and on the performance of certain structures subjected to blast vibrations. However, only limited information is available on the performance of earthfill dams and other hydraulic structures subjected to blasting. The limited data indicate that, whatever the cause, one or several cycles of repeated strains in earthfill dams may cause residual porewater pressure increases. Limiting the peak particle velocity to less than 2.5 cm/s for operating dams constructed of or having foundations consisting of saturated, loose sands or silts and to less than 5 cm/s for other earthfill dams, should keep strains below the threshold strains required for residual porewater pressure increases to occur. Porewater pressures should be monitored throughout a blasting operation, and they should be allowed to dissipate, if necessary, before subsequent charges are detonated.

Jan 1, 1987

By Katherine L. Heineken, Timothy J. Tope, Kim David Murphy

One method for small arms disposal is the use of a deactivation furnace or explosive waste incinerator. There are numerous hurdles a facility typically encounters to get the furnace or incinerator fully operational and permitted. For example, one Department of Defense installation was in the permitting process 7 years, which included numerous facility upgrades and modifications. This paper will discuss the technical approach for proactively addressing permitting issues and requirements and will identify potential pitfalls to avoid as well as ways to reduce costs. For example, when determining the waste profile, the facility should forecast its treatment needs (taking into account the net explosive weight limits of the furnace/incinerator) and then classify the wastes into "chemical families" based on the type and composition of the wastes. One waste from each family should then be selected for potential inclusion in the trial burn. Modeling the waste disposal can help to narrow down the number of wastes requiring characterization during a trial burn, as well as the number of analyses.

Jan 1, 1997

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

By Michael S. Wieland, Thomas C. Ruhe

Delay blasting in underground coal results in shock waves traveling through the coal that can damage delay charges remaining in the blast pattern. Undetonated explosives which are dynamically desensitized or react sympathetically from shock wave impact ruin blast results. Such malfunctions, sometimes manifest as misfires, more frequently are covert weak detonations, and result in poor coal breakage and fumes with above normal toxicity. To reduce these mining hazards and resolve charge performance problems, the Bureau of Mines has developed and tested forty prototype rugged explosives in the laboratory. Rugged explosives work properly under difficult circumstances because they not only retain their shock initiation sensitivity but also are resistant to shock damage. This research investigation resulted in one candidate emulsion explosive, formulation #37, which passed all the permissibility tests required by MSHA approval regulations. However, approval was not granted because it reached shelf-life (would not shoot properly) seven months into testing. For research purposes, the remaining tests were conducted with a second batch of formulation #37. This paper discusses the prototype rugged explosive composition and permissibility test results. Where possible, for reference purposes, comparisons are made to a commercial product that has been approved. Further research work is required to overcome the noted deficiency of short shelf-life.

Jan 1, 1992

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By John F. Vynne

This paper will discuss the application of available monitoring technology on blasthole drills with the goal being to reduce costs and increase productivity. Case studies from the monitoring of blasthole drills in North American open pit mines will be used to illustrate the ability to meet these objectives.

Jan 1, 1997

By Michael S. Wieland

Toxic fume concentrations from industrial mining explosives depend somewhat upon the type of rock (or other strata) confinement. Though traditional detonation theory disregards this influence, the work principal from thermodynamics reveals it, when the violent interactions that transpire within the rock blast are taken into proper account. Resolution of the work principle technique requires total thermodynamic equilibrium under constraint, so the nonequilibrium dynamics is rendered in that way, using an old trick from theoretical mechanics that revises the representation of forces. The rock pressure reduces to a four-component sum: the rock compressive strength and natural atmospheric pressure, as reckoned quasi-statically, and the gravitational influence and reversed inertial resistance, as reckoned dynamically. Tabulated specie concentrations and graphical trends reveal the dependency upon rock pressure, rock temperature and the fuel-oil percentage in ammonium nitrate mixtures (ANFO), used to illustrate the model. Rigid-wall test chambers have notable ullage (residual space), where rapid expansion influences the reaction quenching, yielding a fume spectrum unlike that for rock confinement; reported rock tests are therefore used for comparisons. For the thermodynamic regime where quenching occurs, seven concentrations are resolved, including carbon monoxide (CO) and total nitrogen oxides (NOX). Their trends yield inferences regarding the way unwanted charge desensitization from transitory hole-to-hole wave impact in conjunction with reduced rock pressure can yield nasty toxic fumes, the dark rusty cloud phenomenon!

Jan 1, 2005

By Lyle Avey

For the purpose of this paper, testwork and general pre-splitting practice will be discussed for the Chimney Creek Mine.

Jan 1, 1990

By Barbara A. Sciever, John H. Sr Schue

Riverboat gambling has caused quite a sensation among people since its talk of coming to Illinois. The year 1992 marked the start of an era for people that had a penchant for gambling, it was the year that riverboat gambling was legalized in the State of Illinois.

Jan 1, 1995

By Jaak J. K Daemen, Carol Geertson

A portion of a tailings impoundment may need to be removed with the expansion of an open-pit mine in northeastern Nevada. The tailings are saturated and consist of fine silty soil. During the removal of the tailings, they would have no support structure and vibrations induced by blasting in the pit could lead to slope failures.

Jan 1, 1998

By R R. Vendebeek

The continuing evolution of explosives has most recently introduced emulsion explosives and heavy ANFO's to the market place. An explosives engineer has a multiplicity of explosives to choose from: dynamites, slurries, water gels, emulsions, ANFO's, and mixtures of some of these products.

Jan 1, 1987

By Frederick R. Cosgrave

Blasting near buried Natural Gas pipelines has always been an area of great concern. Given the many variables that the blaster must contend with in determining how to break the rock while trying to keep the vibration low and doing so while not compromising the pipeline.

Jan 1, 1995

By Tom Short

The contract to drive twin 4,100 foot (1250.5m) long tunnels under the existing Cumberland Gap highway was awarded to a Joint Venture of S.A. Healy of Chicago, Illinois and Lodigiani USA of Fairfax, Virginia in January of 1991 under a $51.8 million bid. Due to very complex geological conditions, there were six distinct categories of excavation, the New Austrian Method of ground support was utilized throughout.

Jan 1, 1993

By Anne Charline Sauvage

Blast designers and blasters need to know the rock mass influence on blast to increase explosive effi-ciency and to optimize costs, but also to succeed in limiting blast emissions (vibration, overpressure, flyrock) This paper presents an applied approach which makes it possible to structure the information con-cerning the rock mass and the blasting.

Jan 1, 2013