Search Documents

By Chad Ducey

The proper utilization of energy in an explosive column is of paramount importance to the success of any blast. Historically, Powder Factor (the weight of explosive per mass or volume of material to be blasted or its inverse), has dictated the blast design. The concept of Energy Factor is a more effective method to design a blast. In order to utilize explosives efficiently, the energy contained in any given product must be quantified. The Powder Factor method, although historically successful, assumes that a pound of cast pentolite affects the material to be blasted the same as a pound of ammonium nitrate / me1 oil (ANFO.) Years of experience and scientific testing have led the blaster in the field to believe otherwise. The next logical technological step is Energy Factor. The Energy Factor method that will be discussed in this paper takes into consideration not only the weight of the explosive, but also the weight strength (Cal/g) and the density (g/cc) to yield a constant relative Energy Factor. The result of such a method is a factor that can be used in the field exactly the same as Powder Factor, but that reflects the relative energy of any given product in terms that will reflect the relative cost benefit of that explosive selection. The Energy Factors associated with different available explosives make it possible to compare the difference in the amount of energy per loaded pound in each unit length of borehole. This paper will examine the concept of Energy Factor in an in depth manner and also compare this quantification method to that of Powder Factor. It will also demonstrate the value of using Energy Factor and how it can improve the efficiency of a blast design. The misconceptions that come along with using Powder Factor will be examined and comparisons will be made between boreholes loaded using Powder Factor and those that are loaded using Energy Factor. This paper will clearly define the differences between these blast design methods and allow the reader to realize the production, quality, and economic advantages of using the Energy Factor method.

Jan 1, 2000

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987

By AN Gupta, N V. Srinivasa Rao

Initiating devices like detonators use sensitive primary explosives. Successful detonation of secondary explosive is achieved by suitable source of energy from primaries. The most widely used primaries contain toxic lead azide and lead styphnate, dinitrodiphenol or tetracine. All these primaries are very sensitive to friction, impact and heat. The handling of these chemicals is very hazardous and many accidents reported in detonator manufacturing were from these primaries only. In addition to this high sensitivity, lead azide and lead styphnate contain lead which is toxic.

Jan 1, 2014

By Peter F. Bayer, Fred C. Drury

This paper deals with explosives regulations in the State of Wisconsin. As has been typical elsewhere, there has been considerable pressure to add additional restrictions over blasting in Wisconsin. What we believe to be a novel approach to the problem has been developed and is being implemented. Members of this Society have been instrumental in this approach whereby the emphasis of the regulations is directed at permissible levels of blasting resultants rather than at specific methods of blasting. It is our intent that this paper serve as a guide to others who may become involved in similar regulatory review in other states.

Jan 1, 1984

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By M-C. Lee, Shomaker, R. Turcotte, B. Short

This research program was undertaken to better understand the factors causing abnormal NOx fumes generation from blasting operations in surface coal mining. More specifically, unusual quantities of nitrogen dioxide and nitric oxide have been observed at several surface coal mines in the Powder River Basin, Wyoming. All these mining operations have several points in common: (i) Blasting is performed using gravity loaded emulsions or emulsion/ANFO blends (ii) Unusual NOx (Oxides of Nitrogen) emissions are observed mostly when blasting is conducted in the overburden as opposed to the coal seam itself (iii) The overburden consists of very weakly consolidated ground strata, providing relatively weak confinement conditions for the explosives, and (iv) Significant ground water is observed.

Jan 1, 2002

By Satish Kate

Mining of Iron Ore in India is done by Surface Mining methods and most of the deposits are massive and are occurring in Hills, surrounded by green forest cover. While majority of iron ore produced are from mechanized mining systems, some quantities are also produced from semimechanised mines. In mechanized mines, apart from state-of-the-art level of mechanization, the Run-off-Mine ore is subjected to multi-stage crushing, screening and washing/beneficiation, for improving the grade and ensure segregating of different size range. The steel plants within the country have been operating their own captive mines, where both lumps and fines are used in their furnaces. In case of mines, which exclusively supply ores to export market, the lumps produced yield very high price and thus efforts are being made to maximize lumps recovery. The mine, where the author had been associated, is an export-oriented mine which supplies iron-ore to Japanese steel plants.

Jan 1, 2004

By W. J. Birch

The dedicated documenting of blast design and vibration monitoring results forms part of the best practice methodology for today’s blasting operators. This allows regression curves to be constantly updated and in turn compatible charge weight determinations are based upon the most current data. The point can arise however when so much data becomes agglomerated that variations in blast design, geology or monitoring location response and their effects can pass unobserved and start to have an adverse effect on the forecasting capability of the regression due to a deterioration of the standard error statistic. The simple solution would be to only compile like-for-like blasting returns, but this prospect can quickly become unworkable due to the number of potential variables. In addition it is very difficult to spot subtle variations by simply examining a standard scaled-distance curve mainly due to the intrinsic data scatter that is always present together with the logarithmic nature of the regression curve. If indeed a variation is thought to be apparent, how can the degree and magnitude of its influence to be quantified? The Likelihood Ratio Test when applied to regression data can diagnose subtle variations between data sub-sets and provides a comparative statistic as to the degree of variation. By analysing datasets in such a way, levels of compatibility are obtained, indicating which sets can be combined in order to increase prediction capability.

Jan 1, 2004

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Martin Chenoweth

The Metropolitan Water District of Southern California (MWD) is undertaking one of the nations largest water management projects. The Eastside Reservoir Project is being built to insure a supply of water to Southern California in the event of earthquake damage to the aqueducts supplying the region. An 800,000-acre-ft lake will result from the three dams, closing off the valley between two parallel ridges. The single largest contract of the project, the West Dam, was awarded to the joint venture of Atkinson Construction Co., Washington Construction Co. (Morrison Knudsen Co.), and HB Zachry Co. Over 50 million bank cubic yards of rock must be drilled and shot on this contract alone. AWZ relies on the TechBASE database management system for documenting drilling and blasting. The database format of TechBASE allows all production parameters to be linked to the location of the activity. This allows parameters such as drill penetration or boulder production to be analyzed for geologic trends that can either be exploited or dealt with. Shot locations are stored as 3D polygons in a polygon table. Production and cost data are stored in flat tables. Shot names are unique and link the polygon table to the flat table. This allows typical database queries to be made by date, location, cost or any production parameter. The output from these queries can be presented in table, graph and as map formats. The map output is particularly helpful in quantifying geologic conditions and blast performance. The ability to transform the data into information has been very helpful. The ability to present this information graphically has been invaluable.

Jan 1, 2000

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By George P. Schivley

The careful positioning of the drill rigs that drill the holes into which explosives are then loaded is critical to the success of the subsequent blast. Today a system of satellites in space, each transmitting radio signals, is being used to provide the data to allow for tracking and positioning of various types of ground-based mobile equipment. The system is the Global Positioning System or GPS for short. This paper focuses on the application of GPS to surface mining and in particular the navigating of rotary drills from hole-to-hole and their final precise positioning to drill each blast hole.

Jan 1, 1996

By Karl E. Burgher

Accidental explosions occur throughout the world. They can happen at chemical plants, fireworks plants, grain depots, or as a result of collisions involving volatile or hazardous chemicals. It is interesting, as we know as blasters, that we can take two very harmless products and mix them under certain conditions and produce a violent explosion. It is often very difficult for the investigator to determine the magnitudes of blasts after the fact. However, an estimate must be made to settle vibration and airblast damage claims. The blasting consultant or technical representative is often called upon to act as an expert to mitigate these claims.

Jan 1, 1993

By Corry Goumans, Dan Agostino

Photo 1. Demolition work on the Pitt River Bridge. The drill crew is using the 3800 Gardner Denver Air Track to drill the holes on the Bridge turning dolphin. The barge in the background is used for support.

Jan 1, 2013

By R Mancini

Explosive charge action on the medium is intrinsically dynamic (fast rising and fast vanishing). On the contrary, information available on rock strength is drawn from static behaviour, and it's commonly used to characterise the rock, even in blasting problems.

Jan 1, 1995

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By He Guangyi

During rock blasting in extending deep cutting from Jiu Li Mountain to Dong Zhuang Village in Jiao Zhi Railway line, we have drilled deep hole with large scale diving drilling machine and successfully carried on controlled blasting. This has provided new experiences for rock blasting in extending existing cutting. The aim of this article is to provide an introduction to bench height, blast holes arrangement, powder charge calculation, and detonating technique during blasting.

Jan 1, 1997

By Lawrence C. Schneider

In the past decade regulations governing the manufacture, distribution, storage, and use of explosives have proliferated. These laws have been developed by a host of federal agencies with no coordination. The result has been contradictory and impractical standards, which once adopted, are resistant to change or repeal. The current OSHA standards are one example which is examined in detail. The Commonwealth of Kentucky has made progress in modifying these standards, and still providing protection to the blaster and the public.

Jan 1, 1981

By Feng Shuyu Yang Nianhua

According to the results of high speed photography tests, particle velocity measurement tests and the digital calculation with TP2 software, the shape of shock wave, the declined laws of the shock wave propagation speed and the peak particle velocity are described and analyzed in detail. New viewpoints about the theories of blasting fragmentation based on analysis of the progressive pictures of the fracture region are given. The formula for calculating the depth of fracture regions is established on the basis of the new viewpoints.

Jan 1, 1997

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987