Search Documents

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

"The goal of the work was verification of bacterial leaching on the samples of black coal. From the results obtained it was clear that the coal is very well leached by Thiobacillus ferrooxidans and this technology can be used for coal desulphurization. A leaching time of one month is required, to remove 65% of total sulphur and 85% of pyritic sulphur.Microscopic evaluation of samples from Jaworzno showed, that it should be classed as a coal with low coalification, probably from black coal hemiphase. Macerals of the liptinite group were well distinguishable; they were of a dark brown colour. Evidence of coal mass oxidation was apparent on the fresh sample; in the test samples (during bacterial leaching) small grains were oxidised."

Jan 1, 2003

By M. Barsky, E. Barsky

A study was conducted to elucidate the relationship between the hovering velocity and the particle settling velocity. The experiments were carried out in a water medium on five materials ranging in density from 1.070 to 4.000 kg/m3. Analysis of the results with allowance for the distribution of stream velocities over the cross section of the pipe revealed that the final settling velocity of the particles was equal to their local hovering velocity (on the stream axis), and not to the average velocity of vertical flow as is generally believed. It therefore follows that the kinetic structure of the stream must be taken into account when constructing theoretical models of the process for purposes of computation. In addition, the optimal stream velocity is not always equal to the hovering velocity and in fact is governed by other factors as well. Illustration is provided by the results of a study conducted in a vertical cascade classifier comprising eleven identical stages. The feed material was introduced at each stage successively beginning with the topmost (i* = 1 ) and ending with the lowermost (i* = 11). First, the stream velocity that yields optimum separation conditions at each stage of the cascade (i.e. k=50%, k being the yield of a given size class in the fines for a single stage) was sought. Subsequently the conditions of optimal separation for the instrument as a whole were determined (i.e. F(x) = 50%, F(x) being the yield of a given size class for the entire instrument). The results of the study are presented in the table.

Jan 1, 2003

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

By Sarah K. DeBono, Alan J. Monaghan, Emmanuel V. Manlapig, Gregory J. Harbort

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber."

Jan 1, 2003

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"During 2000 Mintek Developed the PlantStar plant wide control platform for the minerals processing industry. The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.Processes with long dead times, like a feed belt to a mill, are difficult to control. The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.Often there are more variables on a plant that need to be controlled (process variables) than there are variables to control them with (manipulated variables). Process constraints are often reached and violated. Safety control loops are necessary to prevent constraints being reached. The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. It continuously perturb the solids feed rate to learn ‘where’ on the curve the mill ‘was’ and then to drive it continuously toward the middle, maximum power drawn. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads by cutting the solids feed to a minimum if the power drop below a specified threshold. Once the power rises above the threshold the solids feed is increased again to an intermediate value from where it start the perturbations again to find the maximum. This makes the milling circuit easier to operate."

Jan 1, 2003

By Jeremy Bosman, Niel Lourens

"Cyclones are used in four main applications in primary wet heavy mineral processing plants i.e. upfront desliming, densifying, and concentrate stacking and tails deposition.UPFRONT DESLIMINGMany heavy mineral ore bodies are associated with high slimes varying from 15 to 60%. The increased viscosities arising from the slimes impact negatively on heavy mineral recovery in the spiral plant. Recoveries can be reduced by up to 10%. Cyclones have proven to be able to remove slime efficiently with acceptable loss of valuable heavy mineral in the overflow. For low slime applications, typically below 25%, it is possible to achieve the desired results using a single stage of cyclones, whilst for higher slimes, two stages of cyclones are required. The overflow of the primary stage is retreated through a second stage to minimize heavy mineral loss."

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a generic global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. As a point of departure we propose that it is not possible to place metals in the context of the sustainable development of society without paying due regard to the entire metals value chain. Thus, the starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions around the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions. The aim of these case studies is to highlight to the minerals processing and metals refining industries their potential role in a more sustainable global society.

Jan 1, 2003

By Francesco Montanari, Gianni Schena

"Recent improvements in X-ray computed tomography allow investigation of objects several tens of millimetres in dimension with spatial resolutions in the order of a few microns. These improvements are made possible by coupling the micro-focus technology adopted by some of the latest cone-beam X-ray sources with an increase in the efficiency of the detectors. The micro-focus technology allows the production of clearer images at high magnification by reducing the penumbra (fuzziness) associated with larger focal spot size.Even higher resolutions can be expected in the next few years with the commercialisation of nano-focus X-ray tubes. In practice one can inspect a system of fine composite particles and analyze the different mineralogical phases in each individual particle. Computed tomography allows accurate liberation studies, e.g. providing liberation spectra or washability data in tens of minutes. However, on-line application of micro-focus computed tomography is unlikely in the foreseeable future, despite rapid development.Dual-energy (DE) radiography is another X-ray technique, which allows retrieval of the volumetric content of valuable components in two-phase particles in a fraction of a second. A digital radiograph of a single two-phase particle produces a grey level image, where the luminosity of the pixels is determined by the sum of the attenuation levels of all the structures. Thus morphological and compositional effects concur to produce the radiographic image, which does not allow retrieval of the composition of the particle, as the 3D-structure of the particle is compressed into a 2D-image, with an obvious loss of information. Thus, in principle it is not possible to discriminate between thick, comparatively penetrable, and thin, comparatively impenetrable mineralogical components."

Jan 1, 2003

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By Natalie J. Shackleton, Deryck de Vaux, Cyril T. O’Connor, Vratislav Malysiak

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. The objective of the study was to investigate the effect surface passivation and inadvertent activation have on flotation and how this can be managed so as to increase the separation of pentlandite and pyroxene. The aim was to minimise the percentage pyroxene reporting to the concentrate and simultaneously maximise the pentlandite recovery. The testwork incorporates the addition of an activator (copper sulphate), a complexing agent, such as DETA (diethylenetriamine) and a dispersant (polyphosphate) at pH 6 and pH 9 in an attempt to alleviate the surface passivation of pentlandite and inadvertent activation of pyroxene. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion."

Jan 1, 2003

By J. Langwaldt

Ammonium-nitrate is a main component in blasting agents and dissolved ammonium residues may be discharged with mine water. The European Union aims to reach a good state of the water quality and recommends ammonium content below 0.5 mg/L for drinking water. Natural zeolites adsorb ammonium from water. In this work, the removal of low-concentration ammonium by commercial natural zeolites was studied in continuous tests. Natural zeolites made up between 83% and 95% of the mineral composition. The major zeolite minerals were chabazite and clinoptiolites and minor amounts of erionite and mordenite were as well present. The five natural zeolite samples, 500~710 µm, were conditioned to obtain zeolites in the Na-form. Ammonium adsorption onto natural zeolites depends mainly on the zeolite mineral type. The chabazite containing zeolite was superior over the four clinoptiolite samples for the removal of low concentrations of ammonium from water (pH of 7.5, flow 5 mL/min, room temperature). The adsorption capacity of chabazite was 48.3 mg NH4+/g zeolites, i.e. 73% of the theoretical exchange capacity 69 mg NH4+/g, during duration over 107 days and almost 6700 bed volumes exchanged. The four tested clinoptiolites had an ad-sorption capacity of 15.7mg to 25.0 mg NH4+/g zeolites. The natural zeolites were rapidly regenerated by an alkaline sodium chloride solution fed to the columns.

Jan 1, 2014

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duval

"The monoalkyl ethers of polyethylene glycols are universal flotation reagents because they can be used as collectors, frothers, surfactants, and depressants. Their collecting power was demonstrated for different minerals including coal and quartz.It was confirmed in this work that monoalkyl ethers of polyethylene glycols could be used as collector in flotation of quartz in a monobubble Hallimond cell. Since feldspar does not float in the same cell, it was also shown that selective separation of quartz and feldspar in the Hallimond tube is possible. However, a trail to use the monoalkyl ethers of polyethylene glycols compounds for separation of quartz and feldspar by flotation of mixture of these minerals in a Mechanobr laboratory flotation machine was futile, indicating that these reagents required special environment for flotation.Most probable parameter responsible for a decrease in quartz flotation in the flotation machine is the hydrodynamics of process, and different adsorption/desorption conditions. To prove this, another series of experiments was carried out to separate quartz and feldspar, in which a laboratory flotation column was utilized. The performance of the flotation column was in between that of in the Hallimond tube and flotation machine. These experiments confirmed that the hydrodynamics of flotation plays a vital role in flotation of quartz with monoalkyl ethers of polyethylene glycol compounds."

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted Xray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system. The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations."

Jan 1, 2003

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

"The work in the paper introduces a 2-dimensional finite element model for analyzing particular material processing in a roller press. Two basic roller geometries are considered: (a) smooth rolls (used for milling and compaction) and (b) rolls with cavities, commonly used for briquetting. A model is presented that is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables.MODEL, RESULTS AND CONCLUSIONSAn associated Gurson model was employed as a constitutive model for the material. The calibration of the model was based on experimental results from an instrumented compaction die. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Powder River Basin sub bituminous coal fines with moisture content 9% was used as a model material.Two finite element models have been set up, one for the briquetting roll and one for the “equivalent” flat roll. Approximately 3200 plain strain continuum elements with reduced integration (CPE4R) were used. Lagrangian-Eulerian (ALE) approach in conjunction with judiciously applied remeshing was employed with the commercially-available, dynamic explicit version of ABAQUS finite element code.Comparison of model predictions with experiment shows that there is an agreement in terms of the general trends of experimental values recorded on laboratory roller presses. Gurson model overpredicts stresses at low densities and, as a consequence, overpredicts roll force and roll torque."

Jan 1, 2003

By Dominic Howarth, Diana Drinkwater, Don McKee

At a time when the mining and minerals industry across the world is undergoing unprecedented change, the very fabric of the tertiary education system which is the principal source of trained professionals to the industry is in decline in many countries. The change sweeping the industry is globalisation as evidenced by the emergence of a relatively small number of increasingly dominant corporations with operations in most of the major mining countries. The education sector is struggling to provide sufficient graduates as the viability of small mining schools declines. That is only part of the problem as the global operating industry is increasingly seeking graduates who are comfortable working in different countries and cultures. One obvious response to the industry needs and developments is for the education sector to consider how it can best respond to the global opportunities. This paper presents the case for a global education network which is based on a network of international thinking Universities and which makes use of the latest in educational thinking and technologies to provide a quality education and in the process produce graduates fitted for international careers.

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003