Search Documents

By G. J. Mei

Separation of hematite and iron-containing silicate gangue - aegirine by Flotation using fatty acid collector and (NH4)2SiF6 depressant was investigated in this paper. The flotation tests with single minerals show Ammonium hexafluorosilicate (AHFS) is a selective depressant for aegirine in hematite flotation in weakly acidic medium, which can strongly reduce the flotation recovery of aegirine in the pH range of 4~5 while has no evident effect on the flotation of hematite. The results of flotation tests with actual ores show the separation of hematite from aegirine gangue by forth flotation was possible, and good selectivity was achieved. Chemisorptions were observed on aegirine mineral surface treated by AHFS solution by using SEM and IR spectrum measurements. On the basis of coordination chemistry, a comprehensive mechanism, which reasonably explains the selective depression of AHFS for iron-containing silicate, is also proposed.

Jan 1, 2014

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By Sushanta Majumder

The physico-chemical characteristics of raw materials used for the production of iron ore pellets have a strong influence on the productivity of pelletization operations and on the quality of pellets. Since iron ores from different sources are used for making iron ore pellets and since the quality of the ores varies with time, there is a need to optimize and control pellet plant operations on a regular basis to achieve optimum productivity while maintaining pellet quality within the desirable specifications. In order to achieve this objective, a model-based on-line optimization system was implemented on two industrial scale induration furnaces. The optimization system consists of a rigorous mathematical model of the induration process, a model for the permeability of the bed of pellets, a statistical model for the quality of iron ore pellets and an optimization module based on sequential quadratic programming. The rigorous model is tested on-line using the wind-box temperature available real-time. The process was optimized to enhance induration furnace productivity for the given constraints on pellet quality parameters such as the cold compressive strength (CCS) and Tumble Index (TI), and other equipment design parameters. Process variables such as induration machine speed, cold air flow rate and hood temperature profile were used as the optimization variables. The on-line optimization system was successfully implemented in two industrial induration furnaces and lead to enhanced productivity. Details of the on-line optimization system and results of process optimization will be presented.

Sep 1, 2012

By A. Buchanan, M. Mirnezami, A. L. Restrepo, J. A. Finch, M. S. Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally revealed two aggregation maxima at pH 8-10 and 10-12. From measurements on sphalerite and silica suspensions the double maxima were replicated by Zn ions (pH 8-10) and Mg ions (pH 10-12) corresponding to the presence of zinc hydroxide and magnesium hydroxide, respectively. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By E. Barsky

Physical principles of two-phase flows with a polyfractional solid phase have not received a sufficient theoretical interpretation as yet. Two-phase flows in the separation mode with a counter-flow of particles are even more complicated. Only statistical methods give an insight into general regularities of such processes. These processes can be interpreted best by analogy with the statistical model of an ideal gas developed by L. Boltzmann, although here a number of difficulties arise. The notion of a statistical system for such flows is substantiated. A mathematical estimation of a statistical system is presented. New notions are introduced, namely, potential extraction of a system and lifting factor. A relationship having the physical meaning of entropy is derived for a two-phase flow in the separation modes. The connection of this new entropy with flow parameters, such as the number of particles, separation factor and chaotizing factor, is established. Properties of this entropy are analyzed, as well as the analogy and difference between this entropy and Boltzmann?s entropy. The notion is formulated and the definition of the chaotizing factor of a process is suggested. In the framework of a statistical approach to two-phase flows in the separation mode, the notion of flow mobility has been formulated. Principal regularities of mass transfer in zone/apparatus sys-tem are analyzed. Principal ideas of a cellular model of the process are formulated, and main relationships for its description are derived. Proceeding from the cellular model, a dependence describing the degree of fractional separation of a narrow size grade is found. The analysis of this dependence makes it possible to reveal the crucial role of the Froude criterion for gravitational separation processes. It is found empirically that this parameter is a basis for the affinization of separation curves (Barsky E, Barsky M, 2006; Barsky, 1980).

Jan 1, 2014

By Ajay K. Jha1

Drilling and Blasting are two important unit operations in the production cycle of a mine and a strong link exists between these two and other unit operations/subsystems like loading, transportation, and crushing. Under the present concept of ? Mine to Mill?, it is important to optimize the drilling and blasting operations by applying scientific approach to drilling and blasting using sophisticated instruments and new technologies, which depends heavily on Information technology (IT) to meet this imperative. Development of innovative models and software has lead to blast optimization process. Till date, the blast results are evaluated in terms of available empirical approaches like powder factor, which are too simple to exclude some key parameters or lack in providing reliability because of non-availability of user friendly IT enabled techniques. Although with the help of developed approaches, formulation of user-friendly software to assist the site engineers in effective post blast assessment has started but there is a dearth of holistic approach to design an optimum blast considering the techno-economic feasibility of the subsystems and the geo-mining conditions to achieve blast optimization. The science of IT enablement in drilling and blasting is capable to build innovative models for achieving blast performances which will be doped with productivity, economy and safety with due regard to environment. The present paper discusses the use of existing IT enablement in various mines of India citing the Indian scenario and the future requirements for achieving the techno-economics in overall mining operations.

Sep 1, 2012

By S. Koca

Vast amount of fly ash, bottom ash and slags, are produced each year due to coal combustion in thermal power plants. These products consist of mainly unburned carbon and inorganic compound (such as: silica, alumina, iron oxides, magnesium oxide, phosphorus oxide etc.). These are valuable minerals and can be recycled or recovered if properly processed. One third of the material find application as an ingredient in cement and other construction products, the rest is held in dams or similar dumps, which results in a hazardous impact on the environment, polluting soil and ground water. The unproductive use of land, the associated long term financial burden maintenance and negative environmental impacts have led to realization that alternative uses for combustion by-products as a value added product beyond incorporation in construction materials are needed. At present, there is an intensive search to increase their uses. Other uses of coal combustion residues include as raw material in brick and ceramic tile fabrication, as filler in plastics and paints, extraction of valuable mineral materials, production of zeolites and soil and mine waste treatments. Separation of unburned carbon from bottom ashes by means of flotation was conducted in order to increase the possibility of the recycling of coal combustion wastes. In the flotation experiments collector, dispersant and frother amount, pulp density and pH were tested as variables. After first stage flotation experiments, at optimum conditions, the carbon content was reduced down to 5.58 % in the tailings fraction. This fraction meets the industrial specifications and can be utilized as a cement additive. At the same conditions the carbon content of the concentrate increased to 44.72 % at a carbon recovery of 65.81 %. After the cleaner stage flotation experiment the carbon content of the product is enhanced to 62.53 %. This fraction can be blended back into the coal feed to the power plant boilers.

Jan 1, 2014

By Ho-Seok Jeon

The separation in gravity concentrators is based on the density difference between valuable and gangue minerals. In addition to density, many auxiliary parameters like particle size, shape, feed rate, pulp density etc. plays an important role in the separation. The performance efficiency of gravity units is largely based on the interference of such auxiliary parameters during separation. Many gravity concentrators are used for the beneficiation of cassiterite ores and performance of which are varying with different feed material, particle size and required enrichment from the unit. Selection of gravity units is generally based on laboratory testing and data collected from the previous experience. In the present investigation cassiterite ore collected from Uljin deposit, South Korea has been subjected to various gravity units like jig, spiral, and Knelson concentrator with the intension to pre-concentrate the ore. Second stage concentration was carried out using shaking tables. The article mainly summarizes performance evaluation methods employed for gravity concentrators. Selection of gravity circuit for the beneficiation of cassiterite was made on the basis of the recovery-grade curve, and Tromp curve methods. Keywords: cassiterite, gravity concentration, recovery-grade curve, sink-float test, tromp curve

Sep 1, 2012

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimisation.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By M. Tang

The phosphate ore sample was taken from the iron tailings after recovering most of magnetite by magnetic separation in Longlin, Yunnan Province of China. Batch flotation tests had been conducted to upgrade the phosphate concentrate by conventional fatty acids reagents under 70% -75 µm of the particle size; however, the unsatisfied results (P2O5 grade of 27.84% and recovery of 49.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than15 kg/t soda ash and 2 kg/t sodium silicate at only one-staged roughing. Based on the analysis of X-ray diffraction (XRD) for the sample, most of gangues are clay, quartz, and chlorite, which may easy to over-grind and deteriorate the flotation process either on reagents consumption or slurry fluidity or viscosity. A hydro-cyclone had been introduced to pre-concentrate the phosphate ore by scrubbing the slime before flotation, which can result obviously in reducing the dosages of soda ash from 15 Kg/t to 4 Kg/t, and raising the grade of P2O5 in the concentrate from 27.84% to 36.13% at the expense of about 4% recovery of P2O5. They also substantially reduced the time of sedimentation of concentrate after flotation from ~10 to ~1 min. In this paper, the effects on the recovery of P2O5 by the different dosages of flotation reagents with or without de-sliming were studied, with the objective of determining the different effects on the functions of flotation reagents by slime during flotation. Keywords: de-sliming, phosphate, soda ash, flotation

Sep 1, 2012

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By A. De1

Because of the extremely low utilization of strain energy in the breakage of solid particles, the energy efficiency prevalent in comminution technology is extremely poor. Schoenert considered that single-particle comminution under slow compression is the most energy-efficient mode of comminution and that energy efficiency should be compared to that. The usual method for grinding minerals and cement has been the ball mill, in which the hit-and-miss aspect of loose-bed comminution severely reduces energy efficiency. The fine grinding of minerals is a particularly energy-intensive process. Schoenert showed that the energy consumed in the comminution of particles in confined beds is second only to that of single-particle comminution under slow compression and developed the method of conducting particle-bed comminution continuously in a high-pressure roll mill. Since its first industrial installation in 1985, the high-pressure roll mill has established itself as the comminution device of choice for significantly improving the productivity and energy efficiency of size reduction from coarse size feeds down to products finer than 20 microns. The first of several hundred installations were in cement plants. The preliminary design and optimization of the industrial operation of high-pressure grinding roll (HPGR) systems, owing to the continuous nature of the device, cannot be efficiently done through laboratory experiments and needs to be achieved through proper system modeling. While the energetics of size reduction in high-pressure grinding rolls has been modeled very well, no model exists for the macroscopic variables in HPGR comminution. In high-pressure roll mill grinding, size reduction results from confined particle-bed comminution under compressive stresses such that the daughter particles produced are highly fractured, stressed, or otherwise weakened. This paper attempts to relate the comminution / compaction behavior for confined particle-bed under compression in a piston-die press with the macroscopic variables in HPGR comminution. A model describing the pressure-densification relationship is presented and used to accurately simulate the macroscopic variables in high-pressure grinding rolls, utilizing experimental data for particle-bed comminution with the piston-die press. The accuracy of the predictive simulations strongly suggests that, starting with a few batch-mode laboratory-scale experiments, it should be possible not only to identify the optimal operating conditions for existing operations but also to successfully design new industrial high- pressure grinding roll systems.

Sep 1, 2012

By N. S. Voiloshnikova

Large-scale continuous ?Resin-In-Pulp? process tests were conducted at Irgiredmet. The object for testing was the sample of oxidized gold ore from one of Siberian deposit. Weak-base ion ex-change resin PuroGold was used as adsorbent. The duration of ?Resin-In-Pulp? tests was sufficient for a completing of three cycles ?Adsorption/Elution?. Gold in feed was 0.95 mg/L. Gold in solid phase of adsorption tails? 0.065 g/t. Gold in liquid phase of adsorption tails? 0.026 mg/L. Total gold in adsorption tails ?0.11 g/t. Gold recovery ?94.3 %. The use of regenerated resin had practically no effect on gold losses with adsorption tails. Alkaline cyanide solution (NaCN-20g/L, NaOH- 5g/L) was used as eluent for gold elution from loaded resin. Elution temperature ?60 °C. Number of eluent bed volumes passed ?10. Loaded resin analysis was following (g/ton): Au? 1700~1250; Ag? 400~460; Cu? 250~450; Zn? 5100~9600; Fe? 860~1200. Elution efficiency: Au? 95.3%~97.8%; Ag? 84.0%~88.0%; Cu? 84.0%~88.0%; Zn? 97.0%~99.0%. Although high zinc resin loading was shown zinc was eluted efficiently. The adsorption properties of fresh PuroGold resin, PuroGold resin after 3 cycle ?Adsorp-tion-Elution?cycles in comparison with AM-2B resin were tested. It was shown from adsorption isotherms that selectivity of PuroGold resin slightly less in comparison with AM-2B resin mainly due to its higher zinc adsorption properties. It was founded on base of test results that adsorption properties of PuroGold resin was practically constant during three ?Adsorption/Elution? cycles. Gold may be efficiently recovered by resin tested. There were no difficulties during gold elution from loaded resin and its regeneration. PuroGold resin was recommended for industrial use in RIP process. Process design criteria were developed and plant design is on progress at the moment.

Jan 1, 2014

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

"This research represents a shift away from empirical models that lock the industry into 50-year old inefficiencies with little response to operating variability. The mechanistic and intrinsically dynamic mill model under development steps up to a new paradigm using the latest computing capabilities and physical understanding of breakage and transport to transform predictive capabilities for design, optimisation and on-line control with variable feed. The milling process is broken down into discrete sub-processes, each of which can be modelled as an object in the whole model and in the model code. These objects can be upgraded or exchanged without having to rewrite or restructure the remainder of the code. Sub-processes include: feed into mill; transport along mill; presentation to impacting events; range of impacting forces; probability of being impacted in different zones in the mill as a function of particle size and density; suspension in slurry; and discharge out of the mill. The unit and processes surrounding the mill (feed and recycle conveyors, slurry pump and pipe, cyclone and recycle crusher) have also been modelled, in order to incorporate the effect of recirculating load coming from a cyclone or a recycle pebble crusher, respectively for ball mills or SAG mills. Each unit is modelled dynamically and PID controllers have been added to control pumping flowrate from sump and water addition for cyclone feed dilution. The paper demonstrates the predictive capability of a dynamic, mechanistic model and is used to test the sensitivity to the sub-processes, comparing different formulations and highlighting the aspects that require further development. Validation on pilot tests and application to industrial data is presented. This approach is currently undergoing industrial trial on sites, for use in on-line model-informed process control. Considerable further development is required to incorporate the full mechanistic structure planned for this model."

Jan 1, 2018