Search Documents

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By Ray Everson, Henry Kasaini

"Adsorption of Pd (II) anions on the surface of activated carbon (Norit 0.8) occurred at high proton concentration (0.01 – 2.5M, HCl) in the feed and averaged 27 mg/g. The adsorption process was interpreted in terms of surface ionisation and adsorption model. Enthalpy of adsorption averaged 0.4 kJ/mole indicative of an instantaneous physical adsorption process. We found that the Toth isotherm fit the adsorption data fairly accurately. A combination of the Langmuir and Freundlich equations yields an effective three-parameter Toth equation (1) which is frequently used to describe adsorption on heterogeneous surfaces.Figure 1 shows the comparison between experimental results and the model isotherms. We found that Langmuir isotherms underestimated the adsorption capacity on the porous surface while the Freundlich isotherm overestimated adsorption. Furthermore, the surface coverage at equilibrium was well described by both the Langmuir and Toth isotherms. But, Freundlich isotherm predicted a surface fraction coverage that was higher than unit. Based on better prediction of surface coverage and a reasonable fit to adsorption data, we concluded that the Toth isotherm best described the adsorption data of palladium. The adsorption process was limited by mass transfer resistance through the external film. We estimated the rate constant from equation (2), where e, ?b, and rp are porosity, fluid density and particle radius, respectively"

Jan 1, 2003

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By Johan Nell, Paul den Hoed

"Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and hightitania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes.When large proportions (30 wt%) of carbon are added to the charge, then the reactionTiO2 + 2C + 2Cl2 = TiCl4 + 2COis favoured overTiO2 + C + 2Cl2 = TiCl4 + CO2Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites."

Jan 1, 2003

By Nicolás Luis, Qi Liu, Gonzalo Montes-Atenas

"The prediction of froth flotation performance is still an unresolved topic. Classic industrial models based on particle size, elemental and mineralogical information provides recovery results with deviations that may become significant. One possible reason for this deviation may be the fact that the current liberation analysis provided by electron microscope based techniques does not take into account the outmost surface layer composition of liberated particles. In order to complete the description provided by the liberation analysis, other spectroscopy techniques measuring the extreme surface of the minerals can be tested. For instance, X-ray Photoelectron Spectroscopy (XPS) is a technique which measures the first tens of nanometers providing elemental composition over the particle surface and allows resolving the elemental associations present at the surface sample. However, this information needs to be statistically robust, reproducible and most importantly representative of what is occurring in the process. The aim of this research work is to develop a statistical model based on particle population to evaluate the feasibility of turning the XPS technique into a metallurgical tool. The model consists of classic statistical population arranged in a bed of heterogeneous particles with a known grade and mineral liberation. The simulations showed that the XPS results statistically followed a well-defined pattern. The statistical results were confronted with pilot plant results obtained from a rougher bank when processing a copper sulfide ore from a Chilean mine site. It was observed that the probability function distribution was in agreement with the experimental data. Further analysis on how the XPS results provide valuable information improve the computation of froth flotation recoveries is also discussed."

Jan 1, 2014

By N. ??dyanik, Z. Kugukaldinova, O. Mishurina, Y. Glazkova, E. Mullina

"This paper describes the process flow of a selective processing method for acidic mine waters formed in the copper sulfide industry and characterized by a high content of copper, iron, and manganese ions. The proposed method comprises a series of sequential processes: the 1st stage is the recovery of Cu2+ ions by precipitation, the 2nd stage is the recovery of Fe2+ and Fe3+ ions as a dispersed phase by acid-base precipitation, followed by recovery in the 3rd stage of Mn2+ ions by converting Mn2+ with an oxidizing agent into insoluble forms of manganese and subsequent recovery of the dispersed phase by electroflotation. The developed method was tested on the acidic tailing storage facility (TSF) water of a mining project in the Urals region. The practical results of the implementation of the developed method have shown that its implementation will allow to recover copper, iron, and manganese in the form of salable products with a simultaneous decrease in their concentrations in adjacent water bodies down to the applicable MPCs. The process is a simple one, does not require any sophisticated expensive equipment and can be implemented either as a standalone solution or as part of existing treatment facilities. INTRODUCTION As a result of unsustainable utilization of natural resources in Russia, only a small fraction is processed into commodity products, while the rest is systematically dumped as emissions, effluents, and other wastes, polluting the environment. By amount of waste and concentration of valuable components, those wastes can be classified as aqueous technogenic resources [1, 2]. Therefore, the development of processing methods for this mineral resource category is an urgent and priority task that will significantly improve the industry’s profitability and the environmental conditions in the respective regions. MATERIALS AND METHODS Following research methods were mainly applied in this study: lab-scale and pilot-scale tests in a diaphragmless two-chamber electric flotation cell; for solutions and recoverable process products — chemical analysis using photometric determination techniques for metal cations and atomic adsorption determination techniques for the processing products. The phase composition of the precipitates formed in the process was investigated by X-ray phase analysis in the general-purpose diffractometer with a copper anode DRON-1."

Jan 1, 2018

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By Ricardo Duque-Soto, Gonzalo Montes-Atenas

The depletion of water resources has posed an enormous challenge to the continuity of many mine sites, particularly those located in arid zones worldwide. In Chile, the use of seawater has been foreseen as one possibility to solve this problem. Nevertheless, the direct use of high ionic strength solutions such as those present in the sea has been found to have some drawbacks. Specifically, rhe extraction of copper from complex ores using high ionic strength solutions such as that of seawater has become one of the most relevant topics in the field of copper hydrometallurgy. This study aims to determine the effect of the degree of salinity on copper extraction kinetics in mixed oxide-sulfide ores. A leach protocol was implemented to study the extraction kinetics, varying the degree of salinity of the medium and the temperature. A thermodynamic model was developed to explain differences in the metal extraction. It was found that the ionic strength impacted positively the copper extraction, probably due to the reduction of the effective concentration in solution due to ionic interactions enhancing the diffusive mass transport of copper ions. This effect is observed to be enhanced when up to an overall salinity values close to 20gpl.

Jan 1, 2014

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014