Search Documents

By Hidekatsu Takeuchi, Masaru Sakakibara, Shigeo Tanabe, Kenji Harada, Akihiko Suzuki, Shoji Morihana

"Deep mixing (DM) method, one of the most commonly used solidification methods, is based on the principle of solidifying soft ground. It can be classified into two categories such as Cement Deep Mixing (CDM) method and Dry Jet Mixing (DJM) method which apply hardening agent in slurry condition and in powdery condition respectively. In recent years, DM methods have undergone changes that have evolved them from the traditional method to meet the needs of the diversifying market. Among them, the Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method is a DM method which mixes a cement-type hardening agent in slurry condition mechanically with soils in situ and incorporates the innovative technique, “atomized ejection” that has been developed to allow faster installation of larger diameter columns without sacrificing quality compared with conventional methods. At this technique, the atomized hardening agent is discharged together with compressed air through a device incorporated into the mixing blade. It also has advantages of performing the works with low-displacement of the surrounding soils in consideration of environmental friendliness and with higher penetration capability against hard ground.This paper presents the technological outline of the above-mentioned CI-CMC method, focusing on the atomized-ejection technique, followed by some construction examples, applied to the self-earth-retaining wall, to the hard ground and the area adjacent to the existing structures.INTRODUCTIONAccording to the accumulation of its case histories, Deep Mixing method has been receiving the demands of its application to more challenging conditions, such as harder ground condition, and requirement of lower displacement of the surrounding ground during its operation. In addition, to match its price against the other cheaper methods and widely receive its benefit of higher quality, the cost reduction of Deep Mixing is also one of the major challenges. For the cost reduction, higher productivity and lower consumption of the material to obtain the equivalent strength and homogeneity with the conventional method are required.The Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method has been developed to meet these demands. CI-CMC incorporates the mist ejection that has been developed to achieve faster installation of larger diameter columns without sacrificing quality compared with the existing methods. Normally, we obtain cement columns of about 1.0 m in diameter by using Deep Mixing method. To increase the productivity, it is not preferable to drastically increase the penetration and withdrawal speed of the mixing blades because of the hardness of the ground and restriction by minimum number of passage of rotating blades per a certain height of the soil cement. Instead, the expansion of diameter of the columns will simply increase the productivity. The development of the new mist ejection system, as shown in Photo 1, has enabled the diameter of soil cement columns to 2.0 m on single axis while 1.6 m on double axes. Mist ejection means that the hardening agent slurry is sprayed into the ground in mist form together with compressed air thereby achieving homogeneous mixing and reducing the resistance on rotating blades."

Jan 1, 2015

By Rudolph P. Frizzi

The current trend of increasing augered cast-in-place (ACIP) pile diameter, length, and load carrying capacities demonstrates improvements in installation equipment, increased acceptance, and that quality control is being successfully implemented by the parties involved in the ACIP pile construction process. Quality control is essential for ACEP piles since 24- to 36-in-dia (610-to 915-mm-dia) piles are currently being constructed to sustain design compressive loads of 800 to 900 kips (3555 to 4000 kN). This paper presents a summary of ACIP pile quality control procedures and methods beginning in the design and bid process, through ACIP pile installation, to post-construction. The results of a recent survey of contractors, engineers, equipment suppliers, and researchers routinely involved with ACIP piles in the United States, Europe, and the Middle East are included to address current trends in ACIP piles and quality control.

Jan 1, 2001

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Paul Doherty

It is known that the axial capacity of a displacement piles installed in clay varies with time. Consolidation theory suggests that dissipation of porewater pressure set-up during pile installation would lead to increased effective stress and hence higher pile resistance. In recent years a number of case histories have reported time dependent capacity increases for piles installed in sand. Although there is some debate regarding the physical mechanisms controlling this phenomenon, known as ageing, it is unrelated to pore pressure dissipation as piles in sand are installed in primarily drained conditions. A series of field tests designed to investigate ageing effects in soft clay are presented in this paper. Full-scale load tests on 6m long 250 mm square concrete piles, which were driven into soft clay are described. The piles were first tested approximately 100 days after installation, at which stage full equalization of the excess pore pressures had occurred. Static load tests were then performed up to 10 years after pile installation. The piles exhibited significant ageing, with their shaft resistance increasing by up to 66% over a 10 year period. Possible mechanisms for such aging characteristics are explored.

Jan 1, 2011

By James G. Ulinski, Sebastian Lobo-Guerrero, Vishal B. Patel

"Recently modified design equations used in the transportation industry to calculate side friction and end bearing capacity for drilled shafts are now providing more realistic estimations of capacities than did previous methods. Using multiple case studies and test results from various projects, a more realistic design approach was formulated by the Federal Highway Administration (FHWA), which resulted in greater values of ultimate capacity for side friction and end bearing and in a more efficient design overall.In 2010, the FHWA published GEC-10 – Drilled Shafts: Construction Procedures and LRFD Design Methods, which illustrates a different method of calculating side friction and end bearing resistance and results in greater values for design. In 2014, the Association of State Highway and Transportation Officials (AASHTO) adopted the method put forth by FHWA, which was included in its LRFD Bridge Design th Specifications, 7 Edition. The Pennsylvania Department of Transportation (PennDOT) recently adopted and incorporated the similar methodology as AASHTO for calculating side friction and end bearing for drilled shafts in rock, and these changes are reflected in the 2015 edition of the PennDOT Design Manual, Part 4 (DM-4). This article discusses the past and current design methodology along with a project case study with results from Osterberg Cell (O-cell) load testing, which presents a comparison between the design resistances of ultimate side friction and end bearing and the measured capacities at failure.The Old and the NewEditions of the AASHTO LRFD Bridge Design Manual from 2012 and earlier estimated ultimate side resistance, qs, in rock using the following equation (modified from Horvath and Kenney, 1979):qs=0.65aEpa(qu/pa)0.5 < 7.8pa(f ’c/pa)0.5 where: qu is the uniaxial compressive strength of the rock in ksf; pa is the atmospheric pressure in ksf; aE is the reduction factor to account for jointing in rock; and f ’c is the compressive strength of the concrete in ksi. For intact rock, previous versions of the AASHTO manual required that the ultimate end bearing resistance, qp, was calculated using the following equation: qp=2.5qu."

Jan 1, 2017

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Patrick J. Lydon, Gregory A. Terri

"The recently opened Mansueto Library at the University of Chicago campus was a 2012 OPA runner-up. The dramatic elliptical shaped dome of this structure tells only part of this structure’s story. The underground automated storage and book retrieval system below ground required excavations as deep as 55 ft (17 m). The system that allows the University to store many of its publications well below grade also required an approximately 50 ft (15 m) clear span for the perimeter walls between the lower level and street level slabs. The latter requirement allows the conveyors to operate freely to retrieve and transport publications up to the lobby level. The design-assist-build team worked together to develop the most cost-effective solution for below-grade work in this challenging urban and geologic environment.The perimeter of the new oval-shaped library is over 620 ft (189 m) long and sits in a central location on campus—adjacent to the Regenstein Library and two city streets and the Henry Moore sculpture, which commemorates the location of the first self-sustaining controlled nuclear reaction. The new library construction not only had to meet challenging structural and geotechnical requirements, but also had to be sensitive to its active and historic surroundings. The soils at the site consist of about 25 ft (7.6 m) of sand, followed by lean clay, generally increasing in stiffness to the top of the dolomitic limestone. Five to 10 ft (1.5 to 3 m) pockets of saturated sand also lie on the north side of the site at about 45 ft (13.7 m) below grade. The top of weathered rock varies in elevation from 59 ft (18 m) below grade in the south to 69 ft (21 m) in the north. There is 1 to 2 ft (30 to 60 cm) of weathered rock. Groundwater at the site is about 7 ft (2 m) below grade.The new structure would extend 55 ft (17 m) below grade through saturated sand strata and into weathered rock for part of the structure’s footprint, so it was critical that the new permanent retention system minimize groundwater seepage laterally through the structure’s wall as well as piping through the weathered rock below the structure. The perimeter walls had to be very stiff to minimize ground movement around the structure’s perimeter due to the significant clear span between slabs."

Jan 1, 2013

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By Dzianis Proshchanka, Yoshi Izumi, Koji Mitani, Ayuna Kitaura

"A new pile driving and drilling navigation system has been developed. It utilizes the commonly used surveying total station, combined with an innovative reticle. Conventional crosshairs have been replaced by a concentrically circular reticle called Baum. It allows for easily performed measurements of central axes of cylindrical objects such as piles, chimneys, electricity poles, etc. This provides several significant advantages compared to other existing systems. It is cost-effective as only one operator is required to control deviations in positioning and inclination. Furthermore, repetitive reinstallation of the instrument is not required for every pile driven or hole drilled. It is also a safer method, as workers have no need to be near a pile driver or drilling machine to perform the measurements. With Baum Station, necessary measurements can be performed away from the actual work area. Moreover, it is highly accurate with real-time solutions, as three-dimensional orientation information for the pile/drill is obtained simultaneously with the pile being driven or the hole being drilled. This allows for the highest levels of precision-control and correction to minimize eccentricity of the intended center positioning.INTRODUCTIONBackgroundIn foundation construction for structures, pile foundations are widely used for deep bearing strata. There are two patterns to driving piles: vertically or obliquely to the ground. The shapes of the piles are normally cylindrical. Vertical pile foundations are employed as the foundations of many structures due to their high workability. There is a problem however, which is that this method does not bear measurement data as construction accuracy is visually checked. On the other hand, tilted pile foundations are rarely employed because it is too difficult to ensure construction accuracy. In addition, commonly used percussion methods create noise and vibrations when the piles are hit, while there are advantages that thinner piles are available, ensuring earthquake-resistance, as tilted piles curb horizontal displacements of structures, which may be caused by earthquake ground motion. However, current requirements of cost reduction bring professional attention to tilted pile foundations, which can be driven reasonably and economically with much research of tilted piles having been carried out to improve their capacity. Also, a method of screwing piling has been developed, which produces small amounts of noise and vibrations. This method has solved tasks of workability and environmental burdens, and is becoming more and more common. However, there is a necessity to develop a method to accurately measure angles of piles’ axes in order to drive piles into the ground with appropriate angles. It is also expected to find out a way to control construction information, such as correction amount and driving record."

Jan 1, 2017

By Karl A. Higgins

In August 2004, the long-awaited National Harbor project in the DC metro area sprang to life with the design of Gaylord National Resort and Convention Center. When the project was in its final stages of construction in 2007, it was noted as largest building development of the east Coast and the 4th largest Building project in the U.S. The final construction costs were above $900M and it served as the catalyst for the overall National Harbor development which added another $1B in construction costs over the next few years. The Gaylord Hotel is supported by approximately 150,000 linear-feet of driven precast concrete piling, one of a handful of major DC area projects in the early 2000s that were supported by this pile type. The project overall was a success, but the fast-paced construction schedule created significant challenges to the designers and contractors. Piling installation was the first major building construction task, and it did not start out well. While the test piles were installed without damage, when production pile driving began in the summer of 2005, pile head and body breakage soon became evident. Typical of most highprofile projects, there are many stakeholders involved and an equal number of opinions on why the piles were breaking. The financial and contractual implications of starting the project off awkwardly were evident to all. The pile driving criteria was scrutinized by the contractor, and the engineer’s had reservations about the size and type of the hammers used for pile driving. Ultimately, it was proven the leading cause of pile breakage was neither the pile driving criteria nor equipment, rather the pile materials themselves. The author of this paper is also the Geotechnical Engineer of Record for Gaylord National and many of the adjacent National Harbor buildings including the recently completed MGM casino. About 100 piles were damaged during Gaylord’s construction some requiring multiple piles for replacements. Over the past decade or so, rumors on the causes of the pile breakage have spread in the market, with some alleging this pile type is not compatible with the geologic setting. I have purposely avoided writing this case-study due to the controversy surrounding the subject, but now some 15 years later it seems appropriate to do so considering DFI’s annual conference location. This will be a fact-based assessment of pile breakage at Gaylord and will also include a comparison to the neighboring buildings where far fewer driven piles were damaged, once a more appropriate concrete mix design was required. The pre-cast supplier is no longer in business.

By Daniel P. Stare, Lucian P. Spiteri, Christopher M. Hallahan, James C. Myers

Buckeye Lake Dam was substantially remediated between 2015 and 2018 as a result of unacceptable dam safety performance. A permanent seepage cutoff, consisting primarily of a soil mixed cutoff wall (SMCW) with occasional sections of steel sheet piling, was constructed along the dam alignment. Closures were required at the terminus of the soil mix elements with existing structures or coffer cells, and at locations where new sheet piling was constructed parallel to the new soil mixed cutoff wall, creating a short circuit seepage path. The original proposed design to construct these closures included permeation grouting methods with chemical grouts. However, a combination of multiple chemical grout types, multiple grout pipes, and an extensive post-grouting verification program was required to ensure the design intent was achieved. After award of the project, the specialty grouting contractor elected to evaluate jet grouting as an alternative closure construction method. The advantages of the jet grouting option offered potential schedule and cost savings to the project as well as a superior product for seepage reduction, given the mixed soil conditions at the site. This paper presents an examination of the site conditions and project goals for the construction of the proposed closure elements for the rehabilitation of Buckeye Lake Dam. Descriptions of the original and alternative treatment methods are provided, with expected performance results. A description of the relative strengths and deficiencies of each method, as well as the feasibility and constructability of each method is provided. The implementation of the jet grouting program is presented, including a discussion of the design elements, quality control test methods, movement monitoring, and verification test methods. This paper also examines the risks associated with jet grouting and how those risks were mitigated during the grouting operations. HISTORY Buckeye Lake is situated approximately 28 miles east of Columbus, Ohio and is managed and operated by the Ohio Department of Natural Resources (ODNR) as part of the Ohio State Parks system. The lake is impounded by natural features that exist along the south and east banks of the reservoir, and by the embankment structure constructed along the north and west banks of the reservoir (see Fig. 1). The reservoir site was originally a natural swamp and the original purpose of the constructed dam and reservoir was to provide water to the Ohio and Erie Canal System. Several dam alignments and configurations were constructed during its early history; however, the original embankment is comprised of homogeneous earthen fill. The embankment is 15 ft (4.6 m) high and extends 4.1 miles (6.6 km) from the North Shore abutment along the east, continuing to the abutment at Lieb’s Island to the West. Several spillway and outlet structures exist along the embankment alignment. Most noteworthy are Seller’s Spillway and Amil Spillway. Fig. 2 is a Plan View of the embankment alignment and appurtenant structures at Buckeye Lake.

Jan 1, 2019

By Kim Chan, Bryn Thomas, Ben Dening

"Increased rail capacity is required into Kooragang Coal Terminal near Newcastle, NSW, Australia to relieve rail traffic congestion and improve management of train arrivals. An additional arrivals track is proposed on new embankment within a heavily constrained site located between existing railway tracks, a high pressure gas pipeline located 7m beyond the toe of the embankment and an environmentally sensitive wetland area. Ground conditions at the site consist of deep soft estuarine clays, a soil profile which is consistently encountered throughout this part of the east coast of Australia. Upon determining that a ground improvement solution was required to ensure global embankment stability, various solutions were considered including a piled viaduct, retaining walls, dry deep soil mix (DSM) columns and concrete injected columns (CICs). DSM columns were adopted as the design solution, a decision which was driven by the presence of sensitive infrastructure and a confined site. DSM offered further advantages including reduced impacts on temporary working platform design, where the use of a thinner platform could be justified owing to the lower track loads of a DSM rig relative to other ground improvement techniques.INTRODUCTIONThis paper presents a case study of the design of DSM ground improvement works to provide support for and enable safe construction of a new railway embankment over deep soft soils with a number of nearby infrastructure and other constraints. The project site is approximately 1km long and is constrained by existing railway tracks, a high pressure gas pipeline and a wetland area of ecological significance. Due to the site constraints and ground conditions, a number of ground improvement techniques were considered during the design process, with DSM columns eventually adopted. This paper discusses the design development and the particular suitability of the technique for use in this application.SITE DESCRIPTIONLandformThe site is located along the northern boundary of the Kooragang Coal Terminal (KCT) at Kooragang Island (KI), a collection of former islands located near the mouth of the Hunter River, north of Newcastle, NSW. The topography of the original area was generally flat with mudflats, swamps and mangroves existing along tidal water courses. Subsequent dredged fill reclamation and development has amalgamated the previous islands into the current KI. The site area extends over numerous channel infills including the buried former course of the Moschetto Channel (paleochannel).Figure 1 shows the proposed 1km long new rail corridor construction area in relation to the various natural and man-made site constraints including existing tracks, the high pressure gas pipeline, the wetland area and the existing reclaimed area."

Jan 1, 2015

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Lee R. Buhagiar

As a result of the increased seismic risk and the highly variable geology of Christchurch, finding costeffective foundation solutions has been a challenge for the Canterbury rebuild. The soil profile in Christchurch comprises both terrestrial (Springston Formation) and marine (Christchurch Formation) alluvial deposits with a high groundwater table. The result is a highly variable and interbedded soil profile which is prone to liquefaction and static settlement. Vibro-replacement stone columns are very effective in mitigating liquefaction in clean sand. However, the author’s experience has shown that vibro-replacement stone columns are also effective for treating silty and soft soil layers. Vibroreplacement stone columns can be used to treat these soft soils by increasing the composite soil stiffness and providing a load transfer path to the underlying dense soils. Another challenge encountered in the Canterbury rebuild is the cost of redevelopment of brownfield sites with contaminated fill. The costs of disposing this fill often make projects too expensive. Vibro-replacement stone columns have been used successfully to treat contaminated fill, providing a treated soil profile with uniform performance and reducing the cost of disposing of contaminated fill. This paper looks at several case studies in Christchurch, with highly variable soil profiles, where vibro-replacement stone columns have been used successfully to treat multiple soil layers, from contaminated fill to silty soils and soft and non-liquefiable silt.

Nov 1, 2022