Search Documents

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By Greg Nutson, Jeremy Butkovich, Bill Perkins, Hollie Ellis, Paul Bott

"Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.INTRODUCTIONThe Evergreen Point Bridge conveys State Route (SR) 520 2.6 miles (4.2 kilometers [km]) from Seattle to Medina across Lake Washington. The bridge is located in a seismically active area, and the Washington State Department of Transportation (WSDOT) has determined that the western half of the 1960s-era bridge (the “west approach”) is vulnerable to earthquake damage. WSDOT has begun preliminary design to replace the west approach bridge.The west approach extends about 6,100 feet (1,900 meters [m]) east from Seattle’s Montlake neighborhood, over Union Bay and Foster Island, then into Lake Washington proper (Figure 1). Approximately 5,600 feet (1,700 m) of the replacement bridge would be constructed over water. Subsurface conditions along the bridge alignment consist of 5 to 80 feet (2 to 24 m) of very soft peat and clay, over very dense/hard sand and clay. Multiple pile supported columns support the existing bridge. The new bridge would be supported by 8- to 10- foot-diameter (2.4 to 3.0 m) drilled shafts that extend about 50 feet (15 m) into the underlying very dense/hard soil. To reduce seismic demands on the bridge superstructure, WSDOT has decided to incorporate a base-isolation system into the bridge design."

Jan 1, 2017

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017

Jan 1, 1987

By Larry Rayburn

Augercast piles evolved in the late forties from the process of pressure grouting open holes backfilled with stone. In 1956, a patent was issued for a cast in situ pile by pumping high pressure grout through hollow-stem, continuous flight auger as the auger is gradually withdrawn from the ground. The patent rights expired in 1973 and the use of auger-cast piles greatly expanded with most large deep foundation contractors now installing augercast piles. At one time augercast piles had a bad reputation, partly because of not having a blow count to give some engineers a confidence factor and there were some quality issues. Over the years the quality issues have been eliminated and I am sure the augercast is the most installed pile in private industry and is now being used by some State Agencies.

Jan 1, 2005

By Howard A. Perko, Melinda J. Hummel

"Hydraulically jacked piles, herein referred to as jacked piles, are commonly used for underpinning existing structures to arrest settlement or augment an existing foundation for higher loads. They consist of steel pipe segments coupled together and jacked into the ground using a hydraulic ram. Pipe sections can vary in size from 3"" diameter to 18"" diameter or larger. Jacking resistance is typically provided by dead loads of existing structures. This type of piling system has been utilized for foundation underpinning, repair, and augmentation for more than 120 years, yet little has been published on the capacity, installation standards, and reliability of these systems. Pile load tests from a number of projects are presented and analysed. The data show that previous methods of jacked pile capacity and depth prediction are crude at best. Empirical relationships between capacity, depth, soil type, and standard penetration resistance blow count contain a high degree of scatter. Scatter in the data indicate capacity prediction for jacked piles needs further research and refinement.INTRODUCTIONPush pier, resistance pile, steel pier, and jacked pile are some of the names often applied to hydraulically jacked piles used for underpinning. The term ‘jacked pile’ is more common in building codes and will be used herein. Although jacked piles can be installed for new construction, this paper is focused on piles used for support of existing structures.Jacked piles consist of short segments of pipe or structural steel tube that are coupled together and forced into the ground using a hydraulic ram fastened to or beneath a footing, stem wall, or grade beam of an existing structure. In this way, the weight of the structure provides the resistance necessary to force the pile into the ground. A factor of safety can be achieved in design by redundancy, which is consecutively installing more than one jacked pile to support the same portion of foundation. Installing jacked piles consecutively using the same dead load and then releasing the load after each pile installation allows one to continue adding piles to the same general area until a total aggregate capacity is achieved to account for anticipated dead plus live loads and a desired factor of safety for that area.An engineering schematic of an example jacked pile connected to a footing foundation is shown in Figure 1. Modern jacked piles typically incorporate a steel bracket. There are many sizes and styles of brackets available. Some categories include plate brackets that bolt to the outside of an existing foundation wall, wide and narrow angle brackets that extend under existing footings, pin brackets for attachment to structural steel, and reverse angle brackets for attachment to footing and wall. Table 1 lists example brackets and their benefits."

Jan 1, 2017

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By Nozomu Kotake, Rakshya Shrestha, Ralph Griffin, Stefanos Papadopulos, Jeff Fippin, Sushil Kafle

Direct Power Compaction (DPC) is a deep Vibro-compaction method used for liquefaction mitigation. In DPC, H-beams are used as vibrating rods penetrating deep into the ground, and a vibrating force is applied directly to the tip of these H-beams to densify the loose ground. A characteristic feature of DPC is the use of a flapping plate installed at the base of the H-beam to enhance the compaction efficiency during penetration. In addition, 2-rod and 4-rod type equipment have been developed to improve productivity and enable rapid construction. DPC was selected as the most suitable and cost-effective technique to mitigate liquefaction hazards in two projects in the San Francisco Bay Area, one on Alameda Island and another on Treasure Island. Both sites were capped with hydraulically placed sand fills. Liquefaction analyses indicated excessive liquefaction-induced settlements and large lateral spread without ground improvement. Densification using DPC was performed up to depths of 42 ft to reduce the liquefaction potential of the sand fill to acceptable levels and to allow planned improvements. Cone penetration tests were conducted before and after DPC to evaluate its performance. This paper describes the equipment and process involved in DPC and discusses its application in terms of subsurface conditions and geotechnical design considerations.

Sep 8, 2021

By Shahriar Vahdani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles of highway, including seven bridges, three cut-and-cover tunnels, and an undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles from the San Andreas Fault, which is capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. At the Tennessee Hollow bridge section up to 30 feet of loose sands and soft clays are present. Concerns are raised that standalone drilled piers will experience excessive lateral soil loads from liquefaction-induced lateral spreading pressure resulting in excessive pier head displacement of up to 8 inches. Ground improvement by Cement Deep Soil Mixing (CDSM) is proposed to provide additional foundation stiffness. This paper presents the methodology to: 1) assess the effectiveness of the ground improvement in resisting lateral spreading, and 2) optimize ground improvement design at individual bridge bents based on local site condition. A series of 3-D numerical analyses are conducted and the results show that drilled piers with CDSM ground improvement are capable of withstanding seismic demands from lateral spreading and the lateral pier head displacement is reduced to less than 2 inches. The adopted analytical approach is efficient at modifying design for individual bents and can be considered for future pier foundation design in seismically active areas. IntroductionThe Tennessee Hollow bridge section (Low Viaduct) is an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. As shown on Figure 1, the project site is located about 5.6 miles east of the San Andreas Fault and 12.5 miles west of the Hayward Fault. The Low Viaduct will span over a future wetland habitat subject to tidal fluctuations and potential scouring."

Jan 1, 2014

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950's, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Greg Plutko

Laboratory testing has shown that the Marsh Funnel test can be significantly impacted by long-chain polymer entanglement. In general, shorter hydration time leads to more chain entanglement which in-turn, leads to higher marsh funnel values that values seen for longer mixing. This trend makes it very difficult to predict funnel-viscosity on successive days. Data is presented which helps to explain this chain interaction effect on Marsh Funnel data and how it differs from traditional Fann viscosity. The data suggest that this long-chain polymer entanglement occurs more in samples with less hydration time and decreases as hydration time increases. There is also suggestion that higher polymer concentrations have a greater drop-off in marsh funnel viscosity for a given aging length than do lower solids slurries. Fann rheology was shown to be much less impacted by the hydration time of the PHPA polymers than was Marsh Funnel viscosity. This suggests that the Marsh Funnel viscosity is impacted by some aspect of the slurry that does not affect Fann rheology as strongly. It is known from literature that longer-chained polymers have more potential to entangle and our data support the theory that the Marsh funnel viscosity is greatly impacted by this polymer-chain ‘roping’ entanglement.

By Adrian Gygax, Sarah Gaib, Rod Kostaschuk

The British Columbia Ministry of Transportation and Infrastructure (Ministry) recently completed a slope stabilization project at Ten Mile Slide on Highway 99. The highway is an essential part of the road network connecting the British Columbia (BC) coast with the interior of the province. The landslide was first identified in the mid-1980s and has retrogressed more than 250 m upslope since then, leading to continual and expensive repairs to the highway. The Ministry engaged BGC Engineering Ltd. (BGC) and their structural sub-consultant Gygax Engineering Associates Ltd. (GEA) to develop a stabilization scheme that would halt the slide with an acceptable level of residual risk. The design required careful consideration of construction stages and the stresses induced in the structural components as the slide movement was progressively stopped as construction advanced. Four stabilization design options were shortlisted with the preferred option selected in Fall 2016. The selected solution comprised the construction of five rows of post-tensioned soil anchors upslope of the highway and a tied-back concrete tangent pile retaining wall for the roadway itself as well as reconstruction of the highway alignment, grade and drainage through the slide. Works were installed by top-down construction within defined time allowances stipulated in the contract. Significant engineering was undertaken beyond standard design processes for this complex project, such as comprehensive geotechnical investigations, aerial and terrestrial laser scanning and change detection analyses, pre-production test anchors, detailed geo-structural numerical modelling and due diligence activities to validate and optimize the design. The stabilization works have been very successful with the slide response being as predicted and the highway operating again as full two-lane service.

Oct 1, 2022

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Soorkty Elarabi

The aim of this paper is to discuss the impact of end bearing plate on the capacity of micropile. Preliminary studies have been made in Sudan in specific area of cohesive soil. Experimental works were carried on a number of micropiles with and without end bearing plate. Same diameters, lengths and techniques of placing cement grout are considered, there after the axial load test applied to find out the capacities of micropiles in both cases. Deduced results in each case show that the end bearing plate has no positive impact on micropile capacity.

Oct 1, 2022

By Seyyed Mehdi Radeghi Mehrjou

The current work investigates the behavior of inclined micropiles under seismic loads. The dynamic finite element method (FEM) was employed. Rayleigh damping was applied to the soil, and elastic beam elements were employed to model the micropiles. The micropile structure was assumed to have one degree of freedom as a column with concentrated mass. The numerical modeling of micropiles was performed to explore the effects of their inclination on their seismic performance within homogeneous soils with uniform stiffness. In addition, the effect of soil stiffness was studied by considering various stiffness in soil depth. The results from the studies have shown significant effects on the dynamic amplification and internal seismic-induced loads of inclined micropiles.

Sep 1, 2022

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By Leykam Chris J., Jacobs Scott. A.

"Construction of the New NY Bridge over the Hudson River 25 miles north of New York City is one of the largest civil infrastructure projects presently underway in the United States (formerly Tappan Zee Hudson River Crossing). The $3.14 billion Design-Build contract is also the largest ever awarded by the state of New York using an Alternative Project Delivery method, and the first major public project to use Design-Build. The new 3.1 mile long bridge will replace the existing Governor Malcolm Wilson Tappan Zee Bridge with a modern twin crossing featuring: Iconic side by side cable stay main spans; significant deck widths accommodating eight lanes of regular traffic, wide shoulders, and a shared use pedestrian and bike path; foundation with excess capacity to fully support a future rail bridge; more than 1,000 large diameter pipe piles driven in deep glacial deposits; drilled shafts installed through steep blast-rock slopes on the east shore landings. Geotechnical challenges included varied bedrock and glacial till surfaces with steep slopes and depths in excess of 750 ft.The purpose of this paper is to highlight major features of the New NY Bridge project with specific focus on the design and construction of the foundations supporting the approach and main span structures from abutment to abutment, provide background on alternative project delivery in NY, as well as provide an overview of the design-build process as it was applied to foundation delivery.The 3.1 mile Governor Malcolm Wilson Tappan Zee Bridge was constructed across the Hudson River connecting Nyack and Tarrytown (Rockland and Westchester Counties). Construction started in March 1952 and was completed in 1955 for a cost of $81 million. The seven lane crossing first opened to traffic on December 15, 1955 and coincided with the opening of a 28 mile segment of highway I-87 / I-287 between Suffern NY and Yonkers NY. The bridge is part of the extensive 574 mile New York State Thruway road system owned and operated by the New York State Thruway Authority (NYSTA)."

Jan 1, 2016

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021