Search Documents

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By Ryan Higbie, King Chin, Matthew Anderson, Mike Huggins, Rian Johnson, Dave Sinsheimer

"The Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of New Orleans’ extensive hurricane risk-reduction system constructed following Hurricane Katrina. The project consists of three discrete pump stations and flood gates on the shore of Lake Pontchartrain which provide a storm surge barrier and pump rainwater from the City of New Orleans’ primary drainage canals. The depth of the pump station structures ranged between 39 and 45 feet below sea-level. USACE developed the PCCP project for design-build delivery; granting the project team latitude to develop innovative, cost effective solutions for the project. The use of OPEN CELLTM cofferdams to construct the pump station structures was one such innovation. OPEN CELL structures utilize the strength of the retained soil to anchor cellular sheet pile face arcs; allowing a free-field of construction within the cofferdam. This cofferdam design did not require ground improvement or dewatering around the perimeter of the cofferdam. The free-field cofferdams streamlined construction and large equipment installation within the structures with no encumbrance from internal bracing. Meticulous force-based design, soil-structure numerical modeling, and physical testing were all techniques used to present and gain USACE acceptance of the design on this vital element of the work.PROJECT DESCRIPTIONThe Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of the City of New Orleans’ extensive hurricane risk-reductions system constructed following Hurricane Katrina in 2005. The project encompasses three separate pump stations and floodgate structures located at the mouths of three outfall canals (17th Street, Orleans, and London) on the south shore of Lake Pontchartrain. These three canals, running from the south to north, act as the primary conduits for discharging water from the New Orleans area. Prior to Hurricane Katrina, these canals were operated with pump stations two to three miles upstream of the mouths at Lake Pontchartrain. This left long stretches of levee on each side of the canals exposed to storm surges entering from the lake. Three levee failures occurred along these canals during Katrina; two at London Canal and one at 17th Street Canal. The failures resulted in major flooding of the surrounding neighborhoods, significant damages, and loss of life.Following initial canal levee repairs after Hurricane Katrina, USACE, in partnership with the Louisiana Coastal Protection and Restoration Authority (CPRA), took action to move the line of flood protection to the mouths of these three canals at the edge of the lake. By cutting off the storm surges from Lake Pontchartrain at the entrance to the canal, over ten miles of canal levee would no longer be exposed to storm surge water elevations, significantly decreasing the risk of failure."

Jan 1, 2017

By J. M. N. P. C. Teles, Venda Oliveira P. J., Correia A. A. S.

"AbstractA laboratory work was performed to study the mechanical behavior of a Portuguese soft soil chemically stabilized with binders and reinforced with metallic fibers when subjected to tensile stresses. To this end and in order to compare the tensile strength results done by two different tests, there were conducted two types of experimental tests: Tensile Split Strength Tests (TS) and Direct Tensile Strength Tests (T). The samples tested had the same binder quantity and different fiber contents, which allowed the characterization of the tensile behavior of the stabilized and reinforced soil, as well as the definition of the best fiber content. Results show that the binder is the main parameter controlling the behavior of the stabilized and reinforced soil until failure, while the influence of the fibers is noticed mainly at the post-failure behavior. The comparison between the tensile strength done by T and TS tests shows that the tensile split test can be used to estimate the tensile strength, although its results are lower than those obtained by the direct tensile tests in general.IntroductionDue to its poor mechanical characteristics, the construction on soft soils presents difficulties that require the use of soil improvement techniques such as chemical stabilization. However, even when mixed with binders, the tensile strength of the stabilized soil is poor, requiring, in certain cases, the use of expensive steel reinforcement or metallic beams, with obvious impact on the final cost of the work. Thus, for the cases where the tensile strength is a design requirement, the soil stabilization should be design with another element, whose primary role is to give tensile strength to the improved soil (Teles 2013).To fill the lack of published studies focused on soft soils both chemically stabilized and reinforced with metallic fibers, the present research aims to analyze the behavior of the improved soil when subjected to tensile stresses. To support the research there were conducted direct tensile tests (T) to directly measure the tensile strength of the samples and tensile split tests (TS) or Brazilian tests to obtain it indirectly. The samples tested had the same binder quantity but five different fiber contents in order to study the influence of the fibers in the improved soil behavior. In addition, a comparison between the results of both tests was made."

Jan 1, 2014

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002

By George K. Burke

Underpinning of a structure has been traditionally expensive, time consuming, and, in many cases, caused as much settlement to the existing structure as it was trying to prevent. As underpinning is normally one of the initial tasks and on the critical path on a construction project, there is immense pressure on the subcontractor to speed up his operation so the new structure can proceed; this can cause an adversarial relationship to develop between the owner, engineers, general contractor and subcontractor. Since its introduction to the North American market in the late 1980's, Jet Grouting has not solved all these problems, but where utilized, has shown economical benefits, a faster and safer installation, and a minimal movement of the structures being underpinned. A history of the development of jet grouting is presented; a comparison of this technique versus other grouting methods, a description of the jet grouting system with emphasis on the triple rod systems; case histories of jet grouting used for underpinning and conclusions and references are included to follow the program's themes of: - Recognizing Solutions to Today's Problems - Defining Tomorrows Challenges - Putting America on a Solid Foundation

Jan 1, 1991

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

Jan 1, 1994

By Mike Fabius

The Lakehead Region Conservation Authority is responsible for slopes along the Kaministiquia River, one of the largest tributaries to Lake Superior in Canada. After arresting toe erosion for a mile of riverbank, the remainder of the slope required stabilization to stop further crest regression and to protect the houses, street and services at the top. Stabilization of the 100 ft. high slope was tendered as design-build with a target safety factor of 1.3 and a design life of 75 years. The successful bid was a system of 1.4 inch diameter soil nails up to 40 feet long, installed perpendicular to the slope on a 3 to 5 foot grid. The conventional shotcrete facing was replaced with a ?green? biotechnical facing and special transverse plate heads on the nails. The key to keeping costs low proved to be installation with light equipment working on the slope, and driving the nails without drilling or grouting. Rather than tension, the design was based on bending in the nails, similar to a laterally loaded flexible pile. The paper describes the design and installation of this innovative system. The design is discussed in terms of soil properties, nail resistance as it varies with depth, failure modes, corrosion protection, root design and nail head design. Construction challenges are discussed. The system is compared to an adjacent anchored soldier pile wall built along the same slope 20 years ago. Post construction monitoring results confirm predicted performance.

Jan 1, 2006

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By Howard A. Perko

Soldier pile and lagging is a conventional means of temporary excavation shoring. Timber lagging design has traditionally been based upon the designer's experience or empirical rules. One such method is the Goldberg Zoino chart used by the Federal Highway Administration. Most of these methods restrict the designer to a consistent soil profile, certain pile spacing, construction grade timber lagging, and limited depth. The methods do not take into account surcharge loads or a variety of other factors that could arise. A designer working outside of ordinary circumstances with unusual loads, varying soil conditions, or alternate lagging materials has difficulty estimating lateral earth pressures. In rigid earth retention systems, lateral earth pressure is generally assumed to be constant along the length of the wall. In soldier pile and lagging systems, the lagging is often considerably less stiff than the steel soldier piles. As the lagging deflects, the soil tends to bridge between the stiffer elements resulting in a lower pressure on the lagging. Several previously published methods by others for determining this reduced pressure are summarized and discussed. These methods typically consist of using a portion of the active earth pressure in several different pressure distributions. A simple theoretical model is presented for determination of lateral earth pressures on wood lagging. The model is based on a three-dimensional "silo" shaped sliding wedge analysis. Results of the model are compared with other published methods. The model compares well with these methods which cover the normal spectrum of design situations. In addition, the model can be used to estimate lateral earth pressures outside typical situations.

Jan 1, 2008

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Philip Dubbeling

Conventional dynamic sheetpiling techniques are ill-suited to urban development because of the emission of excessive noise and ground vibrations. Drilled shafts and slurry walls alleviate some of these environmental concerns but add additional problems due to large bulky machines, reliance on dusty concrete plants and urban trucking grief. To solve these problems, pre-fabricated sheetpiles are hydraulically jacked-in by reaction principle using a compact and lightweight press-in machine, a so called the "Silent Piler". Through scientific analysis, definition and systemization of press-in machines and methods, new construction concepts such as the one-step approach, implant structures, functional design and life cycle design have been developed to comply with new basic construction principles.

Jan 1, 2006

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012