Search Documents

By V. C. Pandolfelli, S. F. Santos, L. A. Rodrigues

Under conditions of stable crack propagation at room temperature, the elastic energy stored in ceramic materials is converted mainly to surface energy. However, at high temperatures, creep may also occur in such materials, in which case it will present a ductile behavior. This paper discusses the brittle-ductile transition of a refractory material. Stable crack propagation and creep tests were carried out under a three-point bending device. A commercial ceramic containing 63 wt-% of SiO2 and 31 wt-% of Al2O3 was used as testing material. The results revealed that the change in behavior from brittle to ductile was caused by softening of a vitreous phase present in the material's microstructure.

Jan 1, 2004

By C. G. Kemsley

THE ore as hoisted is very wet, and difficulty was experienced i~ screening it to remove the fines before going to the secondary crusher. In fact, the fines had a tendency to form balls and roll down the screen, and only a small percentage was removed. Their inclusion with the other ore going to the Symons secondary crusher caused excessive spring action and pounding between the adjustment ring and main frame, resulting in abnormal wear between the two. To overcome this, it was decided to wash the fines through the primary screen, and use an Akins classifier to de-water the screenings, pumping the overflow from the classifier up to the mill and discharging the oversize onto the mill-feed belt.

Jan 1, 1945

By V. Pouyafar

Semi-Solid metal alloys, as used in SSM processing, have a special microstructure of globular solid particles suspended in a liquid matrix, which makes them behave differently in forming processes. The sensitivity of semi-solid slurries to temperature variations and their history and rate dependant behavior, make process design and control difficult. Precise selection of the process parameters is necessary in part production. Therefore, a numerical analysis and simulation of the process can be a valuable tool in process design. In this work we proposed a structural dependent model to account for the thixotropic behavior of semi-solid metals. The parameters of the model were then determined using rheometery tests. The results show a good agreement between the model and the experiments.

Oct 1, 2011

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006

By T. Velea

The most widespread methods for producing metallic copper are smelting of copper sulphide concentrates (which generates various types of polluting substances) and the hydrometallurgical route which consists of leaching in sulphate and chloride media (usually employing high temperature, high-pressure and special equipments). This paper presents a process, called VEPE, which consists of oxidizing copper sulphide concentrates in weak alkaline media (Na2C03 orland NaOH solutions), under low pressure and with air sparging. The oxidized concentrate contains less than 0.4% S. Copper is recovered from the oxidized concentrate by the standard leaching-solvent extraction-electrowinning route, with a total efficiency of 98% extraction. The proposed technology could represent a good opportunity to recover copper from sulphide concentrates in a clean, simple and profitable way.

Jan 1, 2007

Over the years, efficient on-line monitoring of performance and status of an electrolytic copper refining process has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Recent innovative developments by Kennecott Utah Copper Corporation and Outokumpu Technology in wireless cell voltage and individual cell temperature sensing opens new possibilities to improve and modernize tank house management. This paper describes the powerful Outokumpu CellSenseTM refinery monitoring system for efficient interpretation of data produced by wireless CellSensorTM system with traditional refinery measurements. Examples from commercial tank house installations demonstrate the benefits of the system to improved process control and operation. The Outokumpu CellSenseTM monitoring system is simple to operate and accessible to all the plant operation teams.

Jan 1, 2007

By M. Özer, F. Boylu, G. Önal

In this study, the fine coal waste subjected to the experiments is taken from the waste stockpile of Soma Coal Plant. The possibilities of its evaluation and the production of clean coal were investigated. For this purpose, Reichert Coal Spiral and Shaking Table are used. The minus 1 mm coal waste includes 60.43% ash and 50% minus 38 micron material by weight. The microscopic observations of the screen fractions were shown that the clay minerals are in fine sizes and the coarser size fractions contain silica and carbonate minerals as ash forming materials. The tests were conducted after desliming. The commercial grade clean coal product containing 29-35% ash with a calorific value of 3800-4200 kcal/kg (15.91-17.58 MJ/kg) was obtained by gravity methods.

Jan 1, 2004

By S. Theobald

Semi-finished copper and copper-alloy products are typically produced by casting, subsequent hot rolling or extruding and further cold working by rolling and drawing. The technological properties of the products depend not only on the chemical composition of the alloys but also on process parameters such as annealing conditions and degree of deformation. In each production step, measuring and control technology is an important tool for optimizing processes and ensuring constant high quality. This paper follows the product all the way from testing incoming scrap packages, chemical analysis of melts, mould level control in casting, non-destructive testing technologies in cold forming processes, controlling geometrical properties in the production process, to the final tests of technological properties. All test methods are focused on the applications and requirements of our customers, as the examples show.

Jan 1, 2007

By G. Plascencia, A. Warczok, M. Zamalloa, T. Utigard, N. Behnood

The objective of this investigation was to investigate interactions between high-grade copper mattes and Rexal 60DB direct bonded basic bricks. The infiltration and attack of Rexal 60DB bricks by copper matte and continuous converter matte was investigated in laboratory tests at temperatures up to 1300 °C. The brick dissolution and infiltration tests did not show any significant difference between the 70% Cu and the 81% Cu mattes. More metallic copper was visible in the pores in the case of 81% Cu matte. An important mechanism for direct-bonded magnesia-chrome brick destruction is that oxysulphides start to infiltrate the brick, followed by slow oxidation of the matte producing metallic copper and cuprous oxide, which then react with MgO and Cr2O3, primarily attacking the direct bonds of the brick.

Jan 1, 2004

By J. E. Moran

A groupd of French capitalists, La Compagnie Française des Mines d'Or du Canada, has undertaken the considerable task of developing Otter creek, in the Atlin district, B.C., by hydraulic mining methods. It has long been known that the gravels of this stream carry sufficiently high values in gold to make it attractive as a mining venture, but it was impossible to ignore the existence of formidable natural obstacles to hydraulicing them, and these needed to be taken into serious account before embarking upon any costly programme of development. The tide to the Otter Creek leases was originally held by Mr. H. Maluin, a French engineer well known throughout the north, to whom was to fall the task of financing whatever programme might be decided upon. It was he, too, who would have to assume the responsibility of finally passing judgment upon the practicability of the various devises for overcoming the adverse natural conditions. With an infinite attention to detail, which I believe to be a characteristic of the French people generally, he studied his problem and was finally able to submit to his financial backers a programme which left the very minimum possible to the hazard of accident or chance. Dr. Mandy, on his visit to Otter creek this season, expressed the opinion that our method of opening this difficult creek presented certain features which might be successfully applied in placer operations elsewhere in British Columbia, and it is largely for this reason that the present paper has been prepared. I shall set forth, as well as I can, the practices which have enabled us to overcome rather easily some of the obstacles which nature had unkindly placed in the path which we must take. The natural flow of water in Otter creek is far too little to deal success-fully with the rather excessive amount of glacial drift overburden which lies directly over the gold-bearing gravels. For this natural defect, the only remedy was to procure more water. This we have clone through a system of flumes and ditches, totalling between ten and eleven miles in length, which bring to the mine a supply of water adequate for our needs.

Jan 1, 1932

By A. Rahimi

The smelting plant at Sarcheshmeh Copper complex commenced working with two reverbatory furnaces, four pierce smith converters, two anode furnace and one holding furnace having a known capacity of 420 metric tons of anodic copper according to the initial design in 1982 (1361 Iranian calendar). During the period from the commencement date up until now, the smelting plant has undergone changes for improvement and enhanced production by substituting holding furnace with another anode furnace, installing the fifth converter and utilizing oxyfuel burners on the ceiling of the reverberatory furnaces. According to the different operational processes in reverberatory, converter and anode furnaces different types of corrosion mechanisms and degradation can be observed in the refractories of copper smelting furnaces. In the case of reverberatory furnaces, the corrosion and degradation of refractories may be factors such as hot corrosion by melt, corrosion attack by the constituents of burning fuel, degradation of sidewalk exposed to mechanical stresses of the feed charge and the hydrostatic pressure exerted by the melt inside the furnace, all of which are due to the unique operational condition governing the reverberatory furnaces environment, i.e. burning fuel atmosphere, charge concentration and combination, furnace temperature, calm melt condition, etc. In the case of converter furnaces, the most likely corrosion and degradation of refractories may be due to the chemical reaction between the melt and degradation of tuyere zones due to sever movement of the melt and mechanical strikes of the punch rod. Also the most essential corrosion reaction occurs around the mouth of the converter because of the mechanical strikes by the cleaning device and thermal heat shock. Other parts inside the furnace are corroded due to the reactions between the fayalite slag and the furnace refractory. In anode furnaces the degradation mechanism is mostly related to the gaseous corrosion (penetration of natural gas or liquid gas inside the refractory structure due to the long period of reduction processes and refining stages. Finally another important factor responsible for destruction of refractories in these furnaces is the copper oxide slag together with the fume constituents of burning fuels.

Jan 1, 2004

By N. Verbaan, Ph. Henry, S. Lamotte

Hydrometal(lurgy) provides an adequate technology to reintroduce otherwise lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Three case studies at an integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed. (1) Non-ferrous leach residues are treated by a leach-SX process to recover their minor metals (Ge) contents. The remaining acid waste solution is used by the fertilizer industry nearby. (2) Residual low quality acid and caustic are used in the processing of zinc industry cements to produce copper, nickel, cobalt and zinc concentrates by several consecutive selective leach - precipitation processes. (3) Copper anode slimes are treated and their precious metal contents are recovered. Depending on the composition of the slimes, separate or combined concentrates of copper, bismuth, tellurium/selenium and silver/precious metals can be produced.

Jan 1, 2004

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By T. H. Etsell, P. C. Holloway

The fly ash produced by oil sands operations in northern Alberta represents a large, high-grade, potential resource for vanadium production in Canada. After extensive batch testing at the University of Alberta, a conceptual process flowsheet for the recovery of vanadium from oil sands fly ash has been developed. The various unit operations for this process, including decarbonization, roasting, leaching, desilication, precipitation, salt recovery and byproduct recovery, are described. Processes for the recovery of molybdenum and ammonium chloride from waste streams from this process, are proposed, as are potential uses for the ash residue; these byproducts represent significant potential sources of secondary revenue while reducing the environmental impact from the process. A preliminary economic analysis for vanadium recovery from oil sands fly ash using this process is also included and several major economic factors influencing its commercialization are discussed.

Jan 1, 2004

By Z. Mubarok

An overview of the problems encountered the electrorefining of copper anodes containing high levels of nickel and antimony is presented. Our investigations have been focusing on the passivation behaviour of the anodes with high contents of Ni, Sb, Sn, and Pb, the formations of kupferglimmer and floating slimes. The results of linear voltammetry, chronopotentiometry and electrolysis test revealed a noticeable lower resistance of the anodes to passivation in comparison to those with lower contents of Ni, Sb, Sn, and Pb. Anode containing kupferglimmer exhibited oxygen gas evolution during the passivation state. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) indicated that tin can replace and/or join antimony in the kupferglimmer structure. Under specified experimental conditions, floating slimes precipitations took place with high Ni, Sb, Sn, and Pb anodes prior to the end of one anode period.

Jan 1, 2007

By F. Golestani-Fard, A. A. Nourbakhsh

In this paper microstructural development of nitride-Bonded SIC refractories is reported in presence of Al203, Mg() and Urea additives .The samples were prepared by mixing, shaping and firing at 1400-1500°c in a controlled atmosphere furnace. Phase analysis, microscopic observation and mechanical evaluation were taken for microstructural investigations. The strength of samples doped with Al203 was first increased and then decreased at higher amount of Al2O3 additions. The addition of MgO decreased the strength while the urea showed an improving effect on strength. These phenomena could be attributed to microstructural evolution and mainly to liquid phase formation and grain morphology. It was found that the additives such as Al203, MO and urea could modify the microstructure in terms of phase formation and texture modification, which in terms influences the mechanical behavior.

Jan 1, 2004

By T. Maruyama

Tamano Refinery started its operation in 1972 with the cathode production capacity of 84,000 tons per year. After several expansions, the production capacity increased to 228,000 tons per year in 2001. In this paper, we are introducing our next expansion projects starting October 2006. The project expands the production capacity of cathode from 228,000 tons to 260,000 tons per year. The main modification of this project is the conversion to the ISA process and the installation of additional seventy-two cells in the No.2 Tankhouse. The No.1 Tankhouse remains the same, using the conventional process. Half of our starting sheet cells are converted to commercial cells. The other expansions are to enlarge our purification plant. And the incidental facilities are enlarged, for example, circulation tanks, heat exchangers, filtration system, etc. Finally, this paper describes those improvements to our refinery performance and preparing for future expansions.

Jan 1, 2007

By Y. Vermeulen, J. Simoes, P. Guillo, A. Di Donate

New design techniques have been developed to optimize continuous casting (CC) refractory components. The overall objective is to increase CC productivity as well as steel quality by using optimized refractory from tundish-to-mold. These techniques allow the prediction of steel and refractory chemical interactions and, thus, steel chemistry evolution as well as build up and corrosion occurrence. Specific fluido-dynamic models (CFD) have also been developed to better take into account the physical parameters at the steel/refractory interface and to optimize steel flow control. The CFD model can be coupled with refractory chemical interactions to simulate steel chemical evolution. These two different approaches result in shape and material modifications. They are completed by dedicated thermal stress analysis in order to improve thermal shock resistance. The mechanical FEA evaluations take into account specific mechanical behavior of refractory components as well as high temperature evolution of their properties.

Jan 1, 2004

By Michel Aubertin

Mining activities can produce large volumes of waste rock, which are typically deposited in piles on the soil surface, above the water table. Such piles can cover areas of several tens of hectares and can reach over a hundred meters in height. For hard rock mines, the waste rock grain size can vary from silty particles to metre-scale blocks. The internal structure of a pile constructed on a relatively flat surface typically includes two main zones. The first zone corresponds to the heart of the pile, and is formed by several sub-horizontal stratifications (with dense and loose layers) due to the heavy mine equipment traffic which induces local compaction and degradation of the waste rock. The second zone corresponds to regions where waste rocks are deposited by push-dumping or end-dumping close to the external flank of the pile, inducing grain size segregation along the slope. Depending on the deposition sequence, grain size distribution and bench height, a gradation may then be observed, with coarser particles (with cobbles and blocks) near the base and finer particles near the crest, together with inclined stratifications due to the advance of the deposition face. These internal features affect the distribution and flow of water (and air) in the pile. To assess the internal distribution of material properties within the pile, a combination of several tools is usually required which can provide information on the hydrogeological and geochemical characteristics of the waste rock. In this regard, geophysical tools are very interesting because they can lead to a threedimensional mapping of property variations. The information gathered from a combination of appropriately selected techniques can be used to construct numerical models to further study unsaturated water flow and reactive transport. Such simulations help better understand the pile response in its actual and future states, which in turn provides input to adjust the deposition sequence, to plan for closure, and to select an in situ groundwater monitoring strategy. The presentation will give an overview of techniques that have been developed to characterise material properties in the laboratory and in the field, and to obtain a general picture of a pile?s internal structure. Additional results on unsaturated reactive transport modelling will also be shown to illustrate how the internal pile structure may influence its hydro-geochemical and environmental response.

Nov 1, 2008