Search Documents

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By O. Kodym

The paper has focused on possibilities of interconnecting information sources concerning monitoring & control of mining industry technical processes (TP), and the related safety hazards. The key issue is the comprehensiveness of the information presented to users. Information can be presented by virtual reality means, when the seemingly true presentation of the production process scene along with user friendly presentation of related information is available. The user in its role of a process supervisor is not only a mere scene observer but, thanks to the interactive functions of virtual environment, he participates in the scene of his control. As such his control and management abilities increase because he can absorb, more easily understand and asses the information provided.

Aug 1, 2013

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By V. Panayotov, M. Panayotova

"Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals and their ability to float is extremely important. The approach presented in this work allows us to draw predictive models for an effective flotation, suitable choice of reagents regime and expected technological results before the minerals enter the flotation process. Attempts to adjust the technological regime in already begun flotation are often unsuccessful because the basic physicochemical processes have already taken place. Mineral processing can be optimized on the basis of objective and basic parameters, decisive for the efficiency of the process - the state of the surface of the mineral; assessment of: minerals flotation ability, the need to apply and the type of needed pretreatment, and expected technological results. The theoretical foundations of such an approach are presented in the work, as well as supporting them experimental results, and information on practical implementation in lead-zinc and copper-pyrite ores selection.INTRODUCTIONIncreasing impoverishment of ores of nonferrous metals incoming to the flotation and rising costs for obtaining the final product lead to the inevitable question - will the mineral processing process be beneficial economically, technologically feasible and environmentally safe and what is the way to improve its efficiency. Some of the possible solutions are already in practice - new more efficient and less energy consuming flotation machines and equipment, new - more efficient and selective reagents, new combinations of flotation regimens, and so on.Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals (sulphides and oxides - most of them with semiconductor properties) and their ability to float is extremely important. This is the subject of research, started in the 60s of the previous century and continuing to the present day. Such dependence would enable a realistic assessment of flotation ability (flotability) of minerals before their flotation processing. The basic dependence, displayed by the researchers as Hoberg (1975), Chanturia and Shafeev (1977), Chanturia and Lunin (1983), etc., represents a relationship between bulk properties of minerals and their flotability, considering especially the concentration of the main charge carriers, namely electrons or holes. The bulk properties are practically constant for minerals from a given field. But the 'main arena' of the flotation process is actually the mineral surface (Carta, 1970; Rao, Labonte, & Finch, 1992; Panayotov, 1999; Rao, 2003; Hu, Sun & Wang, 2010). Therefore, we introduce a methodology for studying the surface of minerals, which methodology gives the degree of semiconductor bands bending on the surface and respectively - the charge of the mineral surface and its ability to interact with reagent-collector. The latter can be used to select the most optimal reagent for the corresponding mineral."

Jan 1, 2016

By V. M. Robb, F. Walraven, L. J. Robb

"The old Albert Silver Mine is a polymetallic deposit comprising concentrations of CuPb- Zn-Ag-U-F within a set of sub-parallel quartz-hematite veins which occur within the fine-grained apical phase of the 2050 Ma old A-type Bushveld granites. Mineralization occurs as an early pyritechalcopyrite- arsenopyrite-galena-sphalerite-(argentiferous) tetrahedrite paragenesis followed by a later, more oxidized assemblage comprising chlorite-hematite-fluorite-pitchblende. Accumulation of metals appears to have taken place at the interface between a coarse-grained porphyritic granite and an overlying fine-grained phase: veins occur in the latter and represent leakage of magmatic fluids from the differentiated, water-saturated, subjacent granite.Mineralization processes in the Bushveld granites are believed to be related to long-lived circulation of dominantly magmatic fluids stimulated by the high heat productive capacity of the host rocks. Endo- and exogranitic tin-tungsten and base metal mineralization formed during an evolving hydrothermal system that lasted for several hundred million years, forming innumerable small- to mediumscale polymetallic deposits. At the Albert Silver Mine, unroofmg of the cover sequences at circa 1600 Ma to 1700 Ma resulted in the incursion of lower-temperature, high-f02 meteoric fluids which remobilized the earlier sulfides and introduced the paragenetically late U-F mineralization."

Jan 1, 1994

By M. Piard

Fires and explosions are not likely to originate in clean gobs above pillar faces steadily driven through a solid panel in order to effect a complete extraction. As. to the storage which such a process implies where the market is intermittent, its cost will never equal that of abandoning large pillars in a fully developed property. Much less will that cost, thanks to the big sizes obtained, ever approach that of cleaning wet and dirty crushings robbed at great expense from small pillars exposed to many years of roof pressure. Even thick seams under bad roof may be fully extracted without the help of filling material. Fatal accidents from falls of roof owing to the great height of excavations, losses in coal, and the danger from fire, have compelled operators in South Staffordshire, England, to discontinue the stall-and-pillar system at one time supreme in the district, and to successfully adopt the following plan: A retreating' longwall is run along the top coal, as the first working; the bottom coal is taken in the same manner, after the fallen roof has become sufficiently consolidated to allow the mine to be reopened. A similar plan is suggested in this paper in order to deal with the outcropping and pitching seams found in the Kootenay measures.

Jan 1, 1930

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By I. J. Burgess, B. C. Barlow

"The electrodissolution of nickel pellets with different controlled electrical variables was investigated in an effort to mitigate plating residue in Watts bath based electroplating cells. During galvanostatic dissolution at 0.4 A dm-2, the anode potential was seen to oscillate between passive and pitting potentials. In-situ microscopy and ex-situ characterization has shown that lacy-pit formation and large, partially perforated, pit covers form during the potential decay from pitting potentials. In general, covered pitting at low current density shows increased plating residue. Using potential pulses is one way to maintain greater control over surface pitting by creating a higher density of pit nuclei while at the same time controlling their growth. Pits generated from a series potential pulses were examined ex situ for a range of pulse times and stages of pit growth were identified. An alternative method of anode dissolution was devised using potential pulses and duty cycles that allowed average current densities comparable to industrial plating conditions to be achieved. By restricting the time at pitting potentials to 0.05 s, plating residue was reduced more than six-fold in comparison to an equivalent galvanostatic experiment run at a comparable current density.INTRODUCTIONIn typical galvanostatic (direct current) nickel electroplating cells employing soluble anodes, some amount of plating residue is produced which consists of metallic nickel and impurities that detach from the bulk in the form of small fines. Significant buildup of residue requires plating operations be halted and the anode assembly cleaned of residue before operation can resume. While variables in the refining process have been shown to affect plating residue, more precise control of electrochemical variables may provide an attractive route to mitigation of residue."

Jan 1, 2016

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By Jose A. Jimenez

"Mining operations generate an enormous amount of data that is difficult to organize, analyze and act on. These data require an extremely broad range of experts to investigate and manage the cross-disciplinary information. The data collects in paper files, diverse databases, historians, stand-alone applications, and excel files. This collection of sources represents everything from monthly, weekly, or daily inputs to real-time feeds or sporadic unscheduled entries. With the operational complexities ever increasing and fewer engineers per mine, an efficient operation is becoming more and more challenging. Engineers are typically burdened with data collection, clean up, and administrative efforts leaving very limited time for engineering assessment and/or optimization analysis. Often optimization becomes limited to the analysis of equipment uptime through existing field automation systems. A great portion of the field data is tucked away in historians seldom reaching those engineers who might leverage the data. Few mine operators have the time or budget to re-architect their operations data collection or management practice, so solutions must enable improvements without requiring expensive or time-consuming implementation. This presentation highlights examples where the aforementioned challenges are addressed using a solution framework designed to enable: 1) data integration and connectivity, 2) monitoring and opportunity recognition, and 3) engineering workflow automation. The initiative extends the concepts and success proven in the automation market segment to all disciplines across the mine operations. INTRODUCTIONThe mining industry by its very nature spends a great deal of its capital on equipment maintenance and replacement. In addition, periodic shutdowns due to equipment failure are typically very costly in terms of interrupted operations. Keeping mining equipment running at peak performance and avoiding costly shutdowns can make a huge difference in the overall return from mining operations. Today, information can be make available that can go a long way towards spotting equipment issues and permitting timely intervention to avoid costly unplanned shutdowns. That said, gathering all of the information from numerous points on many different pieces of equipment necessary to enhance overall equipment effectiveness presents its own daunting issues."

Jan 1, 2016

By R. F. Errington

"Radioactive minerals are found together with the more familiar ore minerals in veins, gossans, and pegmatites, Since they have a peculiar property, that of giving off penetrating radiation, the simplest means of field detection is by the use of some radiation detector.The two principal radioactive elements one may encounter are uranium and thorium. These may occur separately or together. At present there is very little demand for thorium and hence radioactive occurrences should be examined with some care to determine which element is present. To do this it may be necessary to have a chemical analysis made of samples from the occurrence. Uranium minerals that do not carry appreciable thorium have a conventional occurrence in quartz or carbonate veins. They are distinctive in appearance. Pitchblende, the principal ore, is hard, black, and very heavy. It weathers readily to soft, powdery minerals •brilliantly coloured orange, yellow, and sometimes green. It may be associated with familiar minerals such _as native silver, nickel-cobalt sulphides and arsenides, chalcopyrite, and hematite.It is the purpose of this paper to review very briefly the types of radiation detectors available .and to draw some general conclusions as to the types most suitable for particular applications.The highly penetrating gamma radiation is the most useful for detection of radioactive mineralization. The alpha rays have little or no penetration, and beta rays are stopped by thicknesses of a millimeter or so of material. We shall confine our remarks principally to those instruments intended to detect gamma radiation. These are of three types."

Jan 1, 1950

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By Christina Graf

A synthesis of colloidal gold shell particles with a silica core is described. Small gold nanoclusters were attached to the functionalized surface of colloidal silica particles. Reductive growth and coalescence of these clusters lead to the formation of a closed gold layer. By variation of the thickness of this gold layer and the radius of the shell it is possible to adjust the plasmon resonance of the gold shell particles over the whole visible and infrared region of the spectrum. The optical properties of the particles made are in good agreement with theoretical calculations for coreshell particles. Due to their low polydispersity these gold shell particles form in solution large crystals with submicron lattice constants. It is also possible to produce hollow gold shells by dissolution of the silica core. A new method to coat the silica core gold shell particles with an additional outer silica shell is also presented. This allows due to a reduction in the Van-der-Waals forces to make more permanent dried crystals and facilitates functionalization of the particles for use in various photonic applications.

Oct 1, 2003

By Michael Davies

Mined Material Management Meeting or Missing the Mark? o you agree that we have the technology to consistently design robust M3 facilities? ?YES your experience do these M3 facilities perform as expected during operations? ?USUALLY hat can be done to improve performance, e.g. better communications between project and operating teams, discontinuity between design and operational input by designers, others? ?UNDERSTANDINGWHY THINGS GO WRONG an we identify the key characteristics of ?good M3 facilities?, i.e. ones that are performing well? Can we identify ?good M3 facilities?, i.e. ones that perform well and can be held up as examples? ?WITHOUT QUESTION?? your opinion, for what reason do they not perform as expected? ?NO SINGLE REASON??..

May 1, 2010

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

By Bong Sun You

AZ31 magnesium plate of 300mm in width and 40mm in thickness was produced by horizontal continuous casting machine, and its microstructures were analyzed on the surface and in the plate interior. The defect formation on the surface and subsurface, such as side cracks, buckling, pores and segregation, was very sensitive to the casting condition and processing parameters. Especially, casting speed and secondary cooling were the most dominant parameters to control the solidification behavior of magnesium melt, for example the position and shape of the solid/liquid interface in the mould. The cyclic marks on the surface were obvious because the plate were drawn by 4-step cycle and can not be removed. The average grain size of as cast plate measured as 50-65µm at the near surface and 300-400µm in the center of the plate was relatively small because secondary cooling water was applied to control the surface quality resulting in rapid solidification of the melt in the mould.

Jan 1, 2006

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019