Search Documents

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

A pre-flotation process of the Kupferschiefer ore with only frothers produces a concentrate enriched in carbonaceous matter and tailings for further upgrading steps. A partial removal of easy-to-float components of the feed before the main enrichments steps by flotation (rougher, scavenger) improves overall efficiency of separation of valuable elements from the ore. Since the types and doses of frother used for pre-flotation effect the process, the aim of this study was to determine the influence of selected frothers on the efficiency and selectivity of the Kupferschiefer ore processed by KGHM Polska Miedz S.A. A series of pre-flotation tests in the presence of different poly(propylene glycols) ethers, poly(ethylene glycols) ethers and aliphatic alcohols were conducted. The obtained results indicated that the types and doses of frother determine the flotation selectivity of copper and total organic carbon. The evaluation of the pre-flotation process was based on the analysis of selectivity parameters calculated from the recoveryrecovery Fuerstenau upgrading curves as well as the values of copper and organic carbon grades in the flotation products. It was shown that pre-flotation performed in the laboratory scale using a suitable frother provides higher overall flotation selectivity of organic carbon with lower overall flotation recovery of copper in comparison to flotation without the pre-flotation step. Thus, the pre-flotation process improves the quality and quantity of the final concentrates produced from the Kupferschiefer ore.

Jan 1, 2016

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By Timothy W. Ellis, Abbas H. Mirza, R. David Prengaman

Recycled lead, i.e. material produced by the recycling of lead-acid batteries, has become the primary source of lead in much of the world. This has been important to the recycled lead industry as other uses have dwindled, e.g. lead based pigments, chemicals, fuel additives, solders and CRT glasses. Presently, battery manufacturing accounts for greater than 85% of lead consumption worldwide while recycled lead accounts for approximately the same market share of lead supply. Battery manufacturing and production of recycled lead are intimately coupled. In 2007, of all the industrial base metals, lead from lead-acid batteries had the highest recycling rate in North America at greater than 95%. In this paper we will review some of the processes and technologies used in a modern lead acid battery recycling facility, and how recycled lead has become the material of choice for battery construction through the development of a recovery and refining process that exceeds the industry requirements. We will also briefly review an advanced air emissions treatment system in a modern lead recycling plant that demonstrates the feasibility of a new maximum available control technology (MACT) for secondary lead smelters.

Jan 1, 2011

By A. Bauer, P. Katsabanis, M. Baker

The principal results from a previous paper presented at the Mine Accident Prevention Association of Ontario in 1987 (1) are summarized here. It is concluded that the selection of explosives in mines experiencing sulphide ignitions is important and that aluminized explosives should be avoided because of their high explosion temperatures and their detonation products. The duration of the blast is also critical and secondary blasts should not occur simultaneously with nearby priroa:ty blasts.

May 11, 1988

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By J. Warner, K. A. Hughes, P. E. R. Blanchard, J. Esslifie-Dughan, J. W. Reid

Tailings management plays an important role in reducing the environmental impact of Orano Canada’s uranium mining operations in Northern Saskatchewan. Uranium ores mined from Northern Saskatchewan are often associated with large amounts (10-20 wt%) of other harmful elements, such as arsenic and nickel. The JEB Tailings Management Facility (TMF) located at McClean Lake, Saskatchewan is designed to prevent potentially harmful water-soluble elements, particularly arsenic, from contaminating the surrounding environment by promoting the formation of water-insoluble minerals. It is therefore important to determine which arsenic-containing mineral species are present in the TMF and how they evolve over time. Researchers at the Canadian Light Source (Saskatoon, Saskatchewan) were successful in identifying the arsenic mineral species present in tailings samples collected from the TMF in 2013 using X-ray absorption near-edge structure (XANES) spectroscopy. XANES analysis verified that the majority of arsenic species in the TMF existed as amorphous and crystalline ferric arsenates with minor amounts of arsenite and arsenide species. Herein, XANES is again used to analyze a new set of tailings samples collected from the TMF in 2018, specifically focusing on the difference in the distribution of arsenic species in old and new tailings.

Jan 1, 2020

By René Dufour

Jusqu?à son acquisition par MM René Dufour et Alain Robin en 1994, les claims miniers et les droits de surface de la propriété étaient détenus depuis 1953 par la société Québec Columbium, une filiale de la socité américaine Kennecott Copper qui y a réalisé d?importants travaux miniers. En 1995 la compagnie NIOCAN inc. fut incorporée; ses actions furent inscrites à la bourse de Montréal en 1997, et à la bourse de Toronto en décembre 1999. Jusqu?à maintenant, NIOCAN a investi plus de 7 millions de dollars dans le développement de sa propriété minière de niobium située à quelques 40 kilomètres au nord-ouest de Montréal. Le haut rendement économique des deux gisements principaux que compte exploiter la compagnie, le S-60 et le HWM-2, a été établie par des études de faisabilité effectuées par le consortium Met-Chem/SNC-Lavalin. La mission que s?est donnée NIOCAN inc. consiste à mettre en production ses deux gisements et à devenir ainsi productrice de ferroniobium dans les plus brefs délais. Figure 2 Le projet est présentement à un stade avancé d?obtention du certificat d?autorisation du ministère de l?Environnement. À plus long terme, la compagnie compte aussi exploiter les sous-produits de ses gisements (apatite, forsterite, magnétite, calcaire et terres rares).

May 1, 2003

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By G. D. Ruttan

"LYNN LAKE, in northern Manitoba, has become Canada's second nickel-producing area. The discovery by Sherritt Gordon Mines of nickel ore in an entirely new district was the result of systematic prospecting of a belt of volcanics and sediments situated 100 to 150 miles north of the Company's former copper-zinc mine at Sherridon, Manitoba.Prospecting in this area was begun in 1937 and continued each year until 1941, when Austin McVeigh, a company prospector, found a patch of sulphides on a gabbro outcrop near a small lake named Lynn Lake. Samples from this sulphide indicated nickel and copper in significant amount. In 1943, magnetometer work disclosed a number of weak anomalies in low ground near the discovery. In 1945, staking was followed by geophysical surveys and diamond drilling, which continued through 1947. During this period the A, B, E, EL, and Corebodies were located and partly outlined. The discovery of the high-grade ""EL"" orebody in January 1947 was the turning point in the estabishment of the mine. Subsequent development, including additional exploration on surface and under-ground, evolution of a new metallurgical process, financing, erection of a mining and milling plant, hydro-electric power development, building of a rail line from Sherridon (by Canadian National Railways) and a refinery at Fort Saskatchewan, Alberta, culminated in August 1954, when the first shipment of nickel left the refinery. This paper, presented at the 1955 Annual General Meeting of the C.l.M. in Toronto, was one of a symposium covering the whole operation."

Jan 1, 1949

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By Y. Béliveau

Emission of perfluorocarbon gases, CF4 and C2F6, produced during anode effects from aluminum electrolytic cells are a significant part of the total equivalent CO2 emitted by aluminum plants. With the current concerns about global warming, the reduction of these PFC gases is a key issue in reducing greenhouse gases for a smelter and achieving GHG emission agreement goals. This paper will present the approach taken by the Alcoa vertical-stud Soderberg plant in Baie-Comeau to reduce GHG emissions generated during anode effects and close emission gaps with other Alcoa Soderberg plants. The approach has been to adapt the existing technology in place at the Baie-Comeau Soderberg plant. PFC emissions were lowered by reducing both the anode effect duration and frequency through different methods. Examples of change include: implementing skimming practices and wider side crust break area for better alumina dissolution in bath, increasing the ratio between reacted and pure alumina, reducing the time to declare anode effects in the potrooms, implementing best work practices and finally educating the workforce on the importance of reducing PFC emissions.

Jan 1, 2007

By W. B. Dingle

"IntroductionMANY PAPERS presented on developments in the Canadian Petroleum Industry •during the past few years have commenced with this general sentence: ""The past year has been a record •one for the oil industry in Canada, with new records being set in nearly all phases •of exploration and development ,activity"". This sentence applies equally well to 1951. It is not possible to outline all the details of the broken records in exploration, development, and production but general comparisons can be made. There are several significant developments that have stolen the spotlight during 1951, some of which were foreseen in 1950 and some which were not. Among the high-lights were the following:(1) The greatly •expanded activity in the search for gas, which was touched off by the new Alberta regulations covering gas leases and reservations.(2) The discovery of commercial oil production in the Williston basin of North Dakota and Manitoba, which will have far reaching effects on Canadian oil.(3) The greatly increased activity in northern Alberta, northwestern British Columbia, the southern Northwest Territories, Saskatchewan, and Manitoba.(4) The new discoveries in the general central Alberta area.(5) The granting •of a permit for an oil pipeline to the Pacific coast.(6) The arrival of Western Canadian crude in central Ontario.(7) The number of new refineries completed, commenced, or proposed.(8) The present •and proposed expansion in the petrochemical industry.Most of the remarks made on various exploration and development •activities will refer to Western Canada operations, primarily because the greatest •activity and the most significant developments have been there. Eastern Canada exploration and development operations were at a slightly higher level than in 1950."

Jan 1, 1952

By G. E. Rowan

"DURING the dark ages, the cherished dream of chemists was to find a process for converting base metal into gold. Many a wealthy-but-gullible patron lost a fortune in the search. Men who work with metals today are a bit more realistic. I haven't heard of a metallurgist who expects to develop any one alloy that will resist all corrosive media. In the field of stain-less steels, there are about forty different types of alloys that are used where corrosion is a •problem.A stainless product is ordinarily selected because it offers one or more of the following qualities:(1) Resistance to corrosion (2) Resistance to oxidation at high temperatures (3) Good mechanical properties at room temperature (4) Good mechanical properties at high or low temperature (5) Attractive appearance (6) Ease of maintenanceToday we are interested in discussing the stainless steel family of alloys because of their .ability to resist corrosion. We• will not try to explain the Theory of Corrosion. Let us assume that, when surface potential and oxide formations are properly controlled, iron will resist attack in various chemi.cal solutions. The addition of alloying elements to iron does this for stainless steels. The principal stainless alloys used by various Canadian industries are listed in the accompanying Table."

Jan 1, 1959

By R. A. Nemchek

ABSTRACT Concentrator plant design has evolved from large numbers of small grinding mills to small numbers of large mills. Consequently, plant performance often hinges on the productivity of a single large semi-autogenous grinding mill. Industry attempts to address the grinding mills’ critical nature frequently result in specifications that can be made simpler, more economical, and better focused on the project’s goals. This paper surveys current specification writing practices and proposes an improved approach recognizing that product design, procurement, manufacturing, and quality are interrelated in a successful project. The lessons learned here can apply to all types of machinery specifications.

Jan 1, 2014

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By Walker. P. W. A.

Abstract -The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.2160Jo W03 and 0.020% Mo. The deposit is uneconomic at current tungsten prices.

Jan 1, 1994

By Anthony T. Eyton

Intelligent Systems: Advantages for Mining ? Increased safety (reduced risk to workers) ? Increased productivity (reduced downtime) ? Reduced maintenance costs ? Customized solutions for different mines ? Growing acceptance among mine managers A Typical Precarn Project ? Meets definition of intelligent systems ? Involves at least two Precarn members ? a technology developer partner and a user partner ? in a true collaboration ? Involves at least one university and may have various other players ? Leads to a demonstrated prototype ? Costs $2-4 million, and lasts 12-30 months ? Gets up to 40% of its funding from Precarn (max. $1 m) ? Produces new intellectual property -- owned by the project team

May 1, 2002

By Ram Song, Yohei Harada, Shinji Kumai, Kazuho Otsuka

"Recently, vertical-type high-speed twin-roll casting (HSTRC) has been developed. The HSTRC shows extremely high cooling rates over 1,000 K/s even at the mid-thickness area. The fabricated strip has many metallurgical characteristics; super-saturation of alloying elements, fine solidified structure, and homogeneous distribution of fine constituent particles. In Al-Mn based alloys, the Mn alloying element can be supersaturated in the a-Al matrix and also form Mn-containing constituent particles during solidification. The Mn supersaturation and the distribution of primary/secondary particles in cast products affect the metallurgical behavior in the down-stream processing and can improve mechanical properties of the final products. In this study, Al-Mn based alloy strips were fabricated by HSTRC with various Mn contents. The solidified microstructure, constituent particles and its distribution, and Mn solubility were investigated in the as-cast condition. Due to the high cooling rate of HSTRC, fine constituent particles were homogeneously distributed, and coarse intermetallics were not observed. Mn solid solubility was estimated by electrical conductivity. The estimated Mn solubility was equivalent between strip surface and mid-thickness area.INTRODUCTION Al-Mn based alloys, as non-heat treatable wrought aluminum alloys, are widely used in packaging and heat exchanger for automobile industry. Besides Mn, Al-Mn based alloys often contain Fe and/or Si as alloying elements or natural impurities. During solidification, Mn can be super-saturated in the Al matrix, and also form Mn-containing constituent particles. Additionally, in the subsequent thermal-mechanical processes such as homogenization, rolling, and intermediate annealing, Mn in solid solution precipitates out of the Al matrix as secondary particles. The size, distribution, type, and the amount of dispersoids including constituent particles affect to texture evolution, recrystallization behavior, and final mechanical properties of wrought Al-Mn based alloys (Huang et al., 2016; Huang & Marthinsen, 2015; Engler et al., 1995; Muggerud et al., 2013). Therefore, controlling the initial level of Mn super-saturation and the distribution of constituent particles are important in the cast Al-Mn based alloys."

Jan 1, 2018