Search Documents

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

By F. Bélanger, P. Fournier

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northeast of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 60,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill. This paper will highlight the impact of a pre-detox thickener on the cyanide consumption in a gold leach/CIP circuit. While the pre-detox thickener was built with the intention to reduce the cyanide consumption, the opposite effect was observed when the thickener was put temporarily offline. It will show how the re-circulation of a dilute stream of cyanide into the grinding circuit, increases the overall slurry temperature and by the same effect, increases the dissolved copper concentration in the leaching circuit which subsequently increases the cyanide consumption.INTRODUCTION The processing plant is using a conventional gravity, cyanidation and carbon-in-pulp processing facility currently operating at approximately 60,000 mtpd. The comminution process is based on two parallel SABC lines, each fed from an individual reclaim tunnel. Cyclone overflow from the two ball mill circuits is directed to the pre-leach thickener. The thickener underflow is distributed to two (4) parallel leach trains of 5 tanks each, each leach train providing 29 hours of leaching retention time. After leaching, the gold in solution is recovered in a carrousel CIP circuit consisting of two (2) parallel leach trains. Tails from each CIP circuit are combined and sent to a pre-detox thickener to recover as much cyanide solution as is economically practical before being diluted and fed to a cyanide destruction system. The detoxified tailings are sent to the Tailing Management Area (TMA) for settling and retention. The excess water from the TMA is reclaimed and recycled back to the processing plant. The pre-detox thickener is designed to thicken the leach tails slurry to 64% solids with the overflow being recycled to the grinding circuit. It is estimated that the pre-detox thickener will recover 60% of the cyanide in the CIP discharge solution. It is also designed to reduce the SO2 consumption by diluting the thickener U/F to 50% solid using the tailing pond reclaim water which has very little cyanide content."

Jan 1, 2019

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By N. N. Rulyov

"Starting from fundamental principles of colloid-hydrodynamic theory of disperse systems we have shown that application of strongly non-uniform hydrodynamic fields allows to achieve not only faster rates of flocculation of suspension, but also supports significant improvements in the quality of clarified water and separation characteristics of solid phase. Specifically, it has been experimentally proven that the new treatment method based on these principles (then termed as ""ultra-flocculation"") allows:•,Increase the output of thickeners and pressure filters by 1,5-1,7 times;•,Decrease solids fall through into the filtrate in the process of vacuum filtration by 2¬3,5 times;•,Improve the rate of purification of water phase in the upright thickener by 1,5-1,9 times;•,Decrease flocculant consumption by 1,5-3 times;•,Increase the effective operational life time of cloth filters by 3-4 times;•,Ensure sustainable operation of separation equipment, i.e. decrease the sensitivity of process to variation in suspension concentration, as well as to variations of suspension composition and dispersion characteristics;•,Apply flocculant solutions of concentration 2-3 times higher, thus increasing the capacity of equipment used for solutions preparation."

Jan 1, 2004

By Michael Hopp

The beginning of the electroforming technology dates itself on the beginning of the industrial revolution 1800 to 1820 approximately. Basis was the existence of electricity in order to be able to drive the electro-form-process. With the development of the electroforming, big names of the science-history, like Michael Faraday (1791? 1867), Sir Humphry Davy (1778?1829), Max Schlöter (1878?1946), Werner von Siemens (1816?1892), and many others. Already about 1840, the first monograph originated to electroforming (38). While in the first years the electro-forming most extensive only to the coating of art - or other usefulness-objects was used. At the beginning of the 20th century the formation of objects from pure metals became more and more, later also from alloys to application. One of the first bigger electroforming factory, the ?Württembergische Metallwarenfabrik? was working 1894 in Geislingen / Steige, Germany. In the industrial application, the electroforming-technology is to be imagined away for miscellaneous coatingtasks and the form-body-preparation no longer today (18). A little bit confusing is the german name ?galvano-technology?. It based on the Italian physiologist and naturalist Luigi Galvani (1737 ? 1798). This technically seen is however wrong, right, the name is electroforming. The physical bases were founded mainly by Michael Faraday and Sir Humphry Davy.

Oct 1, 2003

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By Jo Render

Expectations of your management approach ??Life of mine applicability ??Tailor scale of activity to scale of project ??Assess impacts, risks, and opportunities ??Use global good practice, backed up by rigorous analysis ??Support with trained monitoring and evaluation team ??Information infrastructure to allow ongoing trend analysis and tracking of progress ??Public reporting using standardized indicators Yes, we are talking about a ?management system?

May 1, 2011

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By H. F. Zurbrigg

"The Frood-Stobie Mine is by far the largest metal producer in the Sudbury area. Its efficient development was made possible by the consolidation of three mining properties that covered parts of the same ore body. They were known as the Frood Mine, the Frood Extension, and the Stobie Mine.The southwest or Frood portion of the orebody was discovered by Thomas Frood and A. J. Cockburn in 1884. Cockburn's interest was acquired by J. H. Metcalf and W. B. McAllister and patents were issued to Frood, Metcalf, and McAllister in 1884. The property was purchased by the Canadian Copper Company (lnco) in 1886.James Stobie discovered the northeast or Stobie part of the orebody in 1885. In 1886 Stobie and Rinaldo McConnell applied for the location and patent was issued in 1886. They sold the property to the Canadian Copper Company (lnco) the same year.The Frood Extension property included very little of the ore zone at surface but it covered ore down the dip from Frood. Frank Cochrane was granted title to the property in 1908 and sold it to the Mond Nickel Company in 1910. The title was transferred to the International Nickel Company in 1929 at the time of the Inco-Mond merger.Prior to 1930 the three properties produced a total of about 1 ,000,000 tons of ore from mining done during the periods 1887-1903, 1913-1915 and 1925-1929. Since 1929 the Frood-Stobie operation has produced more than 120,000,000 tons of ore, about half from open pits and half from square set and blast hole stoping. The current production rate is in excess of 6,000,000 tons per year.The principal products from the ore are nickel and copper. The by-products are iron ore, cobalt, platinum, palladium, rhodium, ruthenium, iridium, gold, silver, selenium, tellurium, and sulphuric acid."

Jan 1, 1949

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015

By F. T. M. White, W. A. Bardswick

"The parameters of airborne minerallic particulates which create industrial dustiness, together with the physiological hazards caused by their inhalation, are reviewed. Various techniques of dust sampling are discussed and analysed, and the parameters referred to above are classified as the basis for methods of assessing the physical, chemical and mineralogical characteristics of dust-particle suspensions. The paper surveys those methods of assessment currently accepted by various statutory authorities, and reviews other methods that warrant attention and newer techniques that are being developed."

Jan 1, 1969

By Louise Corriveau

A Targeted Geoscience Initiative transect in the eastern Grenville Province reveals an extensive VHMS-style cupriferous hydrothermal system among rhyolitic pyroclastic rocks of the Wakeham Group at La Romaine, Québec. The volcanic rocks outcrop sporadically along a < 10 km-wide by about 100 km-long belt correlated with the south-eastern extension of the Wakeham Group. This belt occurs among voluminous, magnetite-bearing, granitic gneiss. At Lake Musquaro, 1.51 Ga metarhyolitic to dacitic lapillistones and flows, locally with aluminous nodules and veins, are intruded by 1.49 Ga feldspar porphyries. This volcanic package was deposited on typical Wakeham Group arenite (< 1.52 Ga) interbedded with nodular, muscovite- and fibrolite-bearing gneiss, and minor marble hosting finely layered garnetiferous hornblendite, garnetite and magnetite-bearing coticule. The latter are interpreted as meta-exhalite and with the associated albitite (sodic alteration), aluminous veins (hydrothermal leaching) and magnetite-rich granitoids, they are key elements in the search for concealed mineral deposits in this area. At La Romaine, to the south, 1.5 Ga lapillistones outcrop structurally above metasediments and below a composite amphibolite unit of uncertain origin (lava or sills) with magnetite-rich (BIF?) units. An extensive zone of aluminous gneiss, with lapilli textures, provide evidences for severe hydrothermal leaching of the volcanic rocks prior to metamorphism. An adjacent siliceous vein-textured unit likely represent a zone of intense silicification (74 wt.% SiO2), while aluminous, hematite to magnetite-bearing veins in adjacent felsic gneiss (tuff?) preserve evidences for the sequence of alteration events. Despite granulite-facies metamorphism, the main characteristics of the amphibolite unit persist along the entire belt. This competent unit likely served as a cap rock; the garnetite, diopsidite and hornblendite it hosts provide effective guides to the sites of fluid discharge and mineralization. A number of Cu showings, modest in size, were discovered in this unit. Their systematic occurrence, in a structural-stratigraphic sense, indicates that this setting is attractive for mineral exploration despite high-grade metamorphism and deformation. Late-stage veins laden with fluorite crosscut these alteration zones, and are themselves metamorphosed, indicating that hydrothermal activity was polyphased. SHRIMP U-Pb ages obtained on detrital zircons (1 arenite) and on igneous zircons (5 volcanic rocks, 1 porphyry and 6 granitoids), pervasive arc-type geochemical signatures and presence of in situ rafts of barium-rich garnetite in the granitoids indicate that sedimentation and volcanism occurred between 1.52 and 1.49 Ga coevally with hydrothermal activity and emplacement of a sub-volcanic 1.5 Ga granitic batholith with early, 1.53 Ga tonalite intrusion. Such a geological context can sustain large-scale hydrothermal cells and development of VHMS, Cu-Fe oxides or SEDEX deposits.

May 1, 2003

By Robert Lamarre

In today?s environment, the availability of production equipment is a must to increase throughput and profits. For a number of mining organizations around the world, spare parts availability is key to achieving this goal. Fortunately, having less production equipment immobilized by a lack of spare parts does not equate to increases in inventory levels or in carrying costs. Advance operations research has shown a number of avenues to increase equipment availability while reducing total investment in stock. The presentation will explore these avenues by focusing on key inventory management changes that can be implemented by organizations to optimize their service and stocking levels. We have successfully applied our approaches in start-up mining projects, in mature projects and in end of life mining operations. We will illustrate our methodology using examples from our work with > 30 mining sites around the world.

Aug 1, 2013

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By S. W. Marcuson, P. J. Mackey

The 1973 Oil Embargo and succeeding disruptions in supply had a profound effect on energy costs and consumption patterns in the developed world. This was especially true in the USA where post World War II growth, fueled by low-cost imported oil, left the country dependent on uninterrupted oil shipments from the volatile Middle East. In this atmosphere, Professor H.H. Kellogg of Columbia University, convinced of the necessity of good environmental stewardship by the writings of the era’s leading environmentalists, developed a methodology for evaluating energy and process efficiency of metallurgical processes and wrote a series of papers describing and applying the techniques. One of these, "Energy Use in Sulfide Smelting of Copper" is recognized as a seminal work which both described the state of energy usage in copper smelting in the mid-1970’s and portended future developments. The background to these papers is examined and the current and past Cu-Ni matte smelting practices in Canada are examined in the context of the results. Data from early 20th century publications describing reverberatory and blast furnace operation is employed to show that energy consumption for much of the century was several multiples higher than that calculated for best reverberatory operation in the 1970’s.

Jan 1, 2015

By S. Shrestha

Magnesium-based alloys are of growing interest for many industrial applications due to their favourable strength-to-weight ratio and excellent castability. Mass reduction has advantages in many industrial sectors for example, in automotive, a reduction in mass improves fuel economy and can lead to more efficient mechanical systems by reducing the weight of moving parts like wheels, gears, pistons. However, the relatively poor corrosion and wear resistance limits the use of magnesium and its alloys in many potential applications. The patented Keronite® plasma electrolytic oxidation (PEO) process enables manufacturers to overcome such problems and, in its latest generation equipment has been developed to industrial realisation for high volume production. This paper presents microstructural characteristics and corrosion performance of two most widely used high pressure die-cast magnesium alloys AZ91D and AM6OB with a duplex corrosion protection coating system that comprised a thin Keronite pre-treatment followed by a subsequent automotive grade final powder coat.

Jan 1, 2006