Search Documents

By G. A. Frame, J. G. Patterson

The 24,000-tpd Frood-Stobie mill grinding circuit operation and control are described. Changes implemented during the past three years to improve grinding efficiency and capacity are discussed.

Jan 1, 1971

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By M. J. Young, C. A. Aird

"The Gem molybdenum prospect is situated at the head-waters of Clear creek, between the Fraser river and Harrison lake, about 30 miles north of• Harrison Hot Springs, B.C. Clear creek follows a deeply eroded fault zone southwesterly through the center of the claim group. Elevations range from 2,000 feet in the creek bed up the steep slopes flanking the creek to a height of 5,500 feet. The property lies within an area underlain by schists and gneisses which strike from north to west in a broad fold plunging steeply to the northeast. This metamorphic complex has been invaded by numerous bodies of grano-diorite, much of which is gneissic. A granite plug, roughly 2,400 by 4,000 feet in size, has intruded this broad fold just west of Clear creek and encloses a circular breccia pipe 1,500 feet in diameter. In the breccia pipe, fragments of metamorphic rocks, granite and quartz monzonite porphyry are firmly cemented in a matrix of quartz monzonite porphyry. All the above rocks are cut by numerous fractures filled by vuggy quartz veins, many of which contain molybdenite. Attentien was first drawn to the area by a quartz vein, 18 inches in width, known as the Gem vein, which consists of several laminated bands of quartz and molybdenite. Since 1964, exploration efforts have been directed toward attempting to outline a large, low-grade type of molybdenum deposit."

Jan 1, 1969

By David J. McDougall

"IntroductionThe production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with the Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivières (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about the Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian rather than the English-Canadian milieu, but whatever the reason, the other Quebec iron work s have been generally ignored. All but one of the Quebec blast furnaces could be described as ""preindustrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day.Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence river. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces."

Jan 1, 1983

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By M. Reda

Because of the adverse environmental effect of Chromate, Molybdate ions had been investigated as replacement for Chromate and the results had shown not to be encouraging. Film deposited from peroxopolymolybdate (from reaction of Molybdenum meta, with excess Hydrogen Peroxide), are more robust than that deposited from molybdate solutions. This was shown to be due to higher fraction of Mo (IV) and Mo (V) that form from Mo (VI) in the peroxopolymolybdate deposited film than the film deposited from Molybdate solutions. The peroxopolymolybdate film contains 40% un-hydrated molybdic acid, tetraperoxodimolybdate and tetra peroxo tetra molybdate. The protective properties of peroxopolymolybdate were shown to be due to the effectiveness of the un-hydrated molybdic acid.

Jan 1, 2010

By W. O. Karvinen

"In the Timmins area, a close spatial and chronological association exists between gold deposits and two major stratabound carbonate-rich members and related quartz-feldspar porphyries. Synvo/canic and metamorphogenic are the two main types of mineralization recognized. Synvolcanic ores include the stratiform quartz-ankerite ""veins"", pyritic carbonates and chert-carbonate-tuff sedimentary rocks and epigenetic ventrelated breccias and stringer zones. Metamorphogenic ores consist of quartz-carbonate fracture fillings in dilatant zones developed during various phases of regional deformation and metamorphism. They are classically epigenetic in character.The evidence suggests a primary syngenetic enrichment of gold on the ocean floor and in vent areas during submarine felsic volcanism and related exhalative-hydrothermal activity followed by further enrichment into quartz-carbonate stockworks during regional deformation and greenschist metamorphism.Although normally thin (a few hundred metres), carbonate members in Archean volcanic terrain represent intense hydrothermal activity which could have transported and enriched gold. They should be used to locate fossil vents and structurally favourable zones where economic concentrations of gold may be found."

Jan 1, 1982

By G. A. Davidson, P. G. Williams

"New developments in centrifugal slurry pump technology are discussed in relation to their importance for improving pump operation and reliability.Experimental data obtained by measuring the velocity of liquid flows in a slurry pump casing using Laser Doppler Velocimetry are presented. This demonstrates the importance of selecting pumps with the proper hydraulic design to provide optimum efficiency, maximum part life and minimum operating cost.The paper also discusses the use of new wear resistant materials, such as ceramic/metal composites, which can significantly improve the life of parts exposed to abrasive media. The results of laboratory attrition tests are presented. IntroductionCentrifugal slurry pumps are of primary importance for the hydro transport of abrasive and corrosive media in the mineral processing industry. As for all process equipment, slurry pumps must be carefully selected and operated to provide optimal performance. To achieve this, it is necessary to select equipment which will provide efficient and reliable operation for the specific service conditions and incorporates the best materials available to obtain maximum parts life.Abrasive wear of liquid end components is the most important aspect that distinguishes the design and application of slurry pumps from other types of pumps. It is therefore necessary to have a fundamental understanding of the mechanical interaction between pump components and the media being handled, as this will impact significantly on hydraulic design, mechanical reliability and selection of wear resistant materials. Recent advances in computational approaches'» have greatly improved the prediction of wear rates in pump casings by facilitating the solution of complex equations which describe the wear mechanisms mathematically. In conjunction with this, new experimental techniques allow researchers to measure flow fields in pump casings using non-invasive devices such as Laser Doppler velocimeters."

Jan 1, 1992

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By R. G. S. Mussi

An inclined cooling plate is utilized as a modification in the compocasting process of magnesium alloy and the mechanical properties of the composites obtained are studied in this work. Based on crystal separation theory, molten AZ91D is poured onto an inclined plate in order to produce solidification nuclei inside the fluid metal, and is mechanically stirred while reinforcement is added. Particulate SiC was utilized as reinforcement in quantities varying from 0 to 15%vol. Dispersion of the reinforcement was observed by macro and microstructure analysis. SiC was properly mixed into matrix until 15%vol., and Vickers hardness tests were carried out for the composites produced. Results obtained for hardness were shown to increase with reinforcement addition and comparable to those of traditional compocasting. Utilization of Inclined Cooling Plate produced good inclusion and homogenization of SiC through an AZ91D matrix, at lower temperatures and shorter times than traditional compocasting.

Jan 1, 2006

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By John Rowson, Caitlin Brown, Kebbi Hughes, Joseph Esslifie-Dughan

The McClean Lake mill in northern Saskatchewan, Canada, is operated by Orano Canada Inc. and has been in production for the last 20 years. The tailings preparation process at the mill has been designed with decommissioning in mind, to produce tailings that are geochemically stable over the long-term within the site’s tailings management facility. Twenty years of study have contributed to a detailed understanding of geochemical and geotechnical properties of the McClean Lake tailings. Validation of the tailings properties has occurred through in-situ sampling campaigns conducted initially every year, and later every five years. Each sampling campaign has applied the same rigorous sampling procedure to provide data with useful correlations year over year. Each campaign result compares elements such as the inherent variability of the tailings, consolidation of the tailings and variations in the tailings placement methods. We will discuss lessons learned from seven sampling campaigns over 20 years and present data to show the reliable tracking of geochemical evolution of the in-situ tailings over time; providing opportunities for continuous improvements.

Jan 1, 2020

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

Agenda ? Introduction ? Inmet?s Operations and Closed Properties ? Inmet?s SECA Philosophy ? Inmet?s SECA Framework ? The Business Case for TSM ? Inmet?s TSM Reporting ? Inmet?s 2004 TSM Performance ? Opportunities for Improvement ? What Have We Learned From The TSM Process So Far? ? Summary Introduction ? Inmet has evolved into a strong TSM supporter ? Inmet is confident that TSM can be successfully and cost effectively implemented by smaller companies ? Inmet?s reporting on economic, environmental and social performance was raised significantly in our 2003 Annual Report ? a signal our commitment to good performance and improvement in these areas ? Our 2004 Annual Report has been further enhanced with the inclusion of our TSM performance

Apr 1, 2005

By J. J. Taute, O. S. Tinkler, G. Zárate, K. C. Sole, J. Steeples

Global practice in copper solvent extraction is reviewed, based on individual plant operating data for 2018. The survey respondents account for almost 40% of global copper cathode production by solvent extraction and electrowinning. Regional trends in operating conditions, as related to the prevailing ore mineralogy, leaching processes, and life of mine are evaluated. The adoption and expansion of this technology in the African Copperbelt and Asia are assessed, together with the associated challenges of specific orebody characteristics. Trends in feed and electrolyte compositions and flow rates, and extractant and diluent selection, together with their impact on copper recovery are reviewed. The evolution of equipment design and associated ancillary processes are discussed, and new projects identified. INTRODUCTION Continuing from similar surveys carried out in 1997, 1999, 2003, 2007, and 2013 (Robinson, Davenport, & Jenkins, 1997; Jenkins, Davenport, Kennedy, & Robinson, 1999; Robinson, Sandoval, & Cook, 2003; Robinson, Moats, Davenport, Karcas, Demetrio, & Domic, 2007; Sole, Zarate, Steeples, Tinkler, & Robinson, 2013), global operating practice in copper solvent extraction (SX) in 2018 is reviewed. Contributing operations include established sites in the USA (8), Chile (9), Peru (2), Spain (1), Mexico (2), and Australia (2), as well as newer operations in Africa (7) and Asia (3). This survey represents 2018 copper cathode production of 1.91 Mt, or about 43% of world production by solvent extraction combined with electrowinning (SX–EW). Trends in operating conditions and performance, as well as equipment design and process technology choices are analysed. The significant expansion in production in the African Copper Belt is also discussed. There are currently about 130 operations worldwide producing some 4.6 Mt copper by SX–EW; of these, about half produced more than 10 000 t/a. Figure 1 shows global copper production by country. As it has for several decades, Chile remains dominant, with 36% of global production of cathode copper. Since 2005, the Democratic Republic of Congo (DRC) has increased production year on year, and now represents 23% of the global total (International Copper Study Group, 2017; Statistica, 2018). Copper production in Asia has grown significantly in the past decade, particularly since the ramp-up of Wanbao in Myanmar. There used to be numerous small copper SX plants in China (Schlesinger, King, Sole, & Davenport, 2011), although most of these have now shut down and Chinese production is lower than it was five years ago. The most important trend, however, is the rise of Chinese-owned mining companies, particularly in Central Africa, but also around the world more generally.

Jan 1, 2019

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By J. M. Shneerson

Gipronickel Institute, Saint-Petersburg will The copper concentrate was extracted from copper and nickel matte after its hydrometallurgical treatment and nickel removal. The concentrate containing 60-74% of copper was represented by two principal copper minerals, digenite and covellite. The oxidising leaching of this kind of concentrate was studied at the Gipronickel Institute. The effect of key parameters, such as temperature, oxygen partial pressure and initial solution compound, on the rate of copper dissolution and transfer of sulphur from sulphide to elemental form was investigated. It was shown that at temperatures about 90DC, the sulphur content of covellite converts to elemental form. Under autoclave conditions at 11ODC, the elemental sulphur dissolves as a sulphate-ion. At the temperature range from 50 to 90DC, the copper dissolution rate is in direct relation with temperature. By increasing the temperature to 130DC, this effect is reversed. Based on the research work, a technological flow sheet for the leaching of the copper concentrate was developed.

Jan 1, 2007

By H. Thalenhorst

For an advanced mineral exploration project that has a ?nugget? issue making the assessment of the deposit grade difficult, a bulk sampling program using a sample tower can provide information that is otherwise not obtainable prior to actual production. This information includes the verification of predicted resource grades for the bulk sample tonnage (and, indirectly, of the methods and parameters used for the grade estimate), confirmation of the physical and grade continuity of the mineralization, and geotechnical data for a future mining operation. The information gathered will improve the input of a feasibility study, particularly with respect to expected mining grades, which are the key economic parameter for most mining projects. The bulk sample rejects can be used for pilotscale metallurgical testwork. Bulk sampling is also useful in cases of potentially biased drill-hole assay results and in the reliable determination of ore grade before shipment of ore from production or development operations to an external beneficiation plant. This paper presents a practical bulk sampling and sample preparation protocol, lists design features for the sample tower, examines the sampling errors that will be encountered, provides information on quality control procedures, and looks at the costs and benefits of such a program, based on the experience of undertaking bulk sampling programs during the period of 1985 to 2008.

May 1, 2010