Search Documents

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992

By A. J. Brown

This paper presents an economic evaluation of resin ion exchange and solvent extraction for the purification and concentration of uraniferous solutions derived from sulphuric acid leaching operations. Capital and operating costs are related to the uranium tenors of pregnant solutions. The conclusions drawn herein apply only to cases where resin and liquid ion exchange are technically feasible process alternatives. It is shown that solvent extraction is economically favoured for pregnant solutions at tenors greater than 0.90 gpl U3O8. Pregnant solutions with tenors below 0.35 gpl U3O8 are best treated by resin ion exchange. Between these concentrations, the economics are marginal and the favoured process is indistinguishable within the limits of accuracy of this study.

Jan 1, 1979

By V. Labiouse, F. Orellana

"Hollow cylinder samples can be tested for both the characterization of rock properties and the physical modelling at reduced scale of engineering applications. Particularly, this type of experimental setup can be used to simulate different stress conditions around underground openings, as already developed in the petroleum engineering field e.g. to study the instabilities around deep wellbores during either drilling or the oil production phase. Some authors have also used this technique to successfully characterize the damaged zone around underground openings in the tunneling engineering field looking for an efficient design of their support.This article presents a new hollow cylinder testing device developed at the Rock Mechanics Laboratory of the Ecole Polytechnique Fédérale de Lausanne (EPFL), Switzerland. It allows a full and independent control of the confining pressure and pore water pressure conditions at both the inner and outer boundaries of Thick-Walled Hollow Cylindrical samples. In order to mimicking a tunnel excavation in a porous rock mass, after initial recovery of the in-situ stress and pore water pressure, the hollow cylinders are subjected to a decrease in the internal confining pressure. Moreover, X-Ray Computed Tomography scans of the specimens are performed through the testing cell before and after the mechanical unloading to monitor the displacements undergone and the sample damage. The equipment, testing procedure and data analysis techniques are briefly presented in the paper.The good performance of the apparatus has already been checked on weak rock specimens, among others on Boom and Opalinus Clay samples. In many configurations, the mechanical unloading is found to induce a Damaged Zone (DZ) around the central hole. Its geometry and extent show a great similarity with in-situ observations around tunnels driven in the Boom and Opalinus Clay formations. Such similarities contribute to increase confidence in the understanding and modelling of the ongoing processes."

Jan 1, 2015

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By M. A. Bergougnou, I. Inculet, K. I. Burgess

This paper describes the electrostatic methods of separating various minerals, reviews the principles of fluidization and outlines the technique of electrostatic sorting in fluidized beds. The application of the method to the benefication of coal is emphasized.

Jan 1, 1970

By Staff

The Tetreault mine, operated by the British Metal Corporation (Canada), Limited, holds a unique position in Canadian mining, being the only steady producer of zinc in Canada east of the Rocky mountains. Its importance in Canadian zinc production may be gauged with some accuracy, since, in 1927, it was responsible for over 13 per cent of the zinc output of the Dominion. In addition, it also made valuable contributions to the production of lead, silver, and gold. Location: Situated in the foothills of the Laurentian mountains, 600 feet above sea level, 20 miles from the St. Lawrence river, and 52 miles due west from the city of Quebec, the property is in the township of Montauban, county Portneuf, Province of Quebec, as shown in Figure I. The municipality of Montauban, immediately adjoining the mine, has a permanent population of 700 people and is six miles by road from Notre Dame station on the main line of the C.N. Rys. between Montreal and Chicoutimi-Notre Dame being n6 miles by rail from Montreal. Connection by 19 miles of dirt-and-gravel road with the Provincial highways&apos; system of Quebec Province, the city of Quebec, which is distant 78 miles, can be reached by automobile in less than three hours, while the distance to Montreal by road is 16o miles .

Jan 1, 1928

By D. J. McLaren

"Arctic Canada is one of the largest undeveloped terrains remaining in the world, and is in many ways unique. The ecological balance of the region is more delicate than tropical or temperate regions of similar size. This region is likely to be developed by research for and production of resources, primarily petroleum, in the immediate future. As well as sensitive terrain surface caused by permafrost in some areas, many large and small mammals and birds are also in a delicate balance with the environment. Small changes in this balance can have large effects.The probability of finding petroleum in different regions varies widely, but already there are good indications on the mainland and in the Islands that both oil and gas are present. Geophysical work in the offshore, particularly the Beaufort Sea, suggests further promising potential. Possible reserves in the Islands and mainland Arctic may amount to 50 or more billion barrels.A responsible approach to problems facing exploitation in an Arctic environment includes the careful monitoring by industry of likely effects of their activities. The Mackenzie Valley Pipeline Research Association test loop at Inuvik provides an example of such monitoring. Outside Canada, the operations at Prudhoe Bay on the north coast of Alaska show how major companies may operate responsibly and reduce environmental interference to a minim'.::at. Nevertheless, four variables must affect any decisions to be made concerning energy resource exploitation in the Arctic. These are man's need for energy, economic and industrial pressures to develop energy sources, the desire to preserve a deteriorating environment, and the role of government as representing all individuals in the country and their several points of view. Factors that must be taken into account in making any decisions include the importance of Canadian oil in a world picture, the need for alternative sources of energy in the near future, the depletion of nonrenewable resources at an accelerating rate and the increasing awareness that the major problems facing man have no direct technical solution and that social or political decisions must precede further techno-logical development."

Jan 1, 1971

By E. Roman E.

A novel anode slime purification process was developed and tested at pilot scale in the Chuquicamata Refinery. The process consists of three main stages: First, an atmospheric alkaline leaching at 90°C, under controlled pH and ORP operation parameters where metalloid impurities are preferentially removed from the anode slimes with high efficiency. In a second stage, alkaline washing of the mud leached with addition of reducing agent, with the intention of reducing the silver of the AgCl to metallic silver releasing the chloride, and finally, copper and other remaining impurities are leached out in mild conditions (60°C, one hour in sulphuric acid). In a side process Se, Te, and Sb are recovery with high efficiency from the alkaline liquor as chemical grade products. The global balance shows a high mass loss yielding a final product with high precious metal and low impurities content showing advantages in both a technical and economic point of view with a clear environmental sustainability. This treatment allows either the direct sale of the purified anode slimes or its pyrometallurgical treatment to obtain metal doré without emissions of Se, Sb and As. Chemical mechanisms for this novel process are also described.

Jan 1, 2007

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By K. C. Hendrick

The paper will review the significant developments in world copper over the past ten years and their impact on the Canadian industry. It will also examine the outlook for the future.

Jan 1, 1971

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By David J. Forrester

"CANMET’s research into underground coal mining is primarily conducted at the Cape Breton Coal Research Laboratory (CBCRL), established in 1981 to conduct safety research in underground coal mines. Located close to Canada’s largest underground coal producer, in the Sydney Coalfield of Nova Scotia, CBCRL’s program also includes the two western underground coal operations. CBCRL is a relatively small laboratory with a staff of thirteen — eight professionals and five support staff — with an annual budget of over $1 million. In order to maintain effective research response, flexibility is key and staff are increasingly working in project teams, crossing traditional section ties and also drawing from specialist expertise elsewhere within CANMET.CBCRL’s research activities have had a substantial impact on the Canadian underground coal mining industry, particularly in Cape Breton. CBCRL contributed to Cape Breton Development Corporation’s (CBDC’s) threefold reduction in lost-time accidents in the 1980s. Also, in the last four years alone, CBCRL’s work has enabled CBDC to save over $17 million in improved utilisation of reserves and cost savings. The work embraces the three traditional areas of mine environment, strata mechanics and mining technologies, however the current direction has been strongly influenced by recent external and internal factors. It is timely to review progress and recent directions."

Jan 1, 1996

By V. G. Papangelakis, G. A. Moldoveanu

The use of anhydrite (AH) seed, control of acidity levels and ageing were assessed as means to promote the conversion of freshly produced metastable gypsum generated in-situ to the less soluble anhydrite phase and force deposition of calcium sulphate on seed as opposed to on equipment as scale, while achieving lower terminal aqueous calcium concentration as well. It was found that moderate sulphuric acid levels (0.25M) and ageing in the presence of AH seed accelerated the gypsum-AH conversion, achieving 100% transformation of the metastable gypsum generated in situ to the more stable, less soluble AH in 6-7 days, while lower/nil acidity did not promote more than 30% AH conversion for 10 days, even in the presence of AH seed. These findings indicate that anhydrite seeding, ageing and incomplete neutralization are beneficial for scale control as well as achieving lower calcium levels, thus rendering the resulting solution more amenable for recycling.

Jan 1, 2015

An optimized long-term mine planning determines the best order of material extraction, so that the Net Present Value (NPV) becomes maximum. In the case of oil sands surface mining, one of the key constraints in NPV maximization is the volume of tailings slurry that will be generated downstream. Specifications of tailings slurry are also important from environmental perspective. Moreover, most of the material that will be used for the reclamation of tailings ponds in later periods is generated in extraction and processing of oil sands. In this paper, an integrated optimization framework is proposed to maximize the NPV of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. The proposed model is coded in Matlab and has been run using CPLEX for verification. The results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Aug 1, 2013

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By Gordon W. Parsons, Ross E. Sampson

"THIS PAPER will trace the work done in bringing the Munro underground ""A"" •Orebody into production to replace the open pit, which was scheduled to be completed early in 1959. Included will be an outline of the exploration work and early planning, and of the final decisions on mining methods. Some of the more detailed work will be described and reasons will be given for the decisions made regarding development work, mine ventilation, ground support, and equipment. Brief mention will be made of open pit operations, as these have had some influence on underground development. Also, some of the main geological features of the ore occurrence will be de-scri0bed, as these had to be taken into consideration when making decisions on ore development and mining methods.LOCATION AND HISTORYhe Munro mine of Canadian Johns-Manville is in Ontario, approximately 50 miles east of Timmins and 40 miles west of the Que-bec-Ontari-0 boundary. The producing orebody is in the southwestern part of Munro township. Property controlled by the Company extends nortl1westerly about 2¥2 miles into Beatty township, on which two other interesting asbestos-bearing zones have been partially expl-0red. Active exploration work on the property was started in March, 194.9, and continued until the summer of 1950."

Jan 1, 1960

By Tom Shumka

INTRODUCTION ?The Electro-Magnetic Crack Detection (EMCD) technique is an electromagnetic inspection method used for detecting and sizing surface breaking flaws. ?It works well on structural material or welds, ferrous or non-ferrous metals. ?EMCD?s rapid scanning is achieved using a hand-held probe. ?EMCD provides reliable crack detection and sizing (length and depth). Cracks can be sized accurately. ?EMCD dramatically reduces most cleaning requirements as there is no need to clean to bare metal. ?EMCD is capable of inspection through thin metallic coatings, or through non-conducting coatings up to 10mm thick. ?EMCD allows full data storage for back-up, off-line view and audit purposes.

Oct 1, 2010

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By I. B. Lambert

The guide has been developed by officials from resources and environment agencies in the Australian Government and the South Australian and Northern Territory Governments. It elaborates on the Australian Government?s policy that new uranium mines are to be approved subject to world best practice environmental and safety standards. The guide outlines the best practice principles and approaches that apply generally to mining in Australia, before giving more detailed consideration to best practice environmental protection and regulation for ISR mining.

Aug 1, 2010

By Heather Budney

Objectives 1. Evaluate the effectiveness of ON?s EA processes using criteria from the EA and policy sciences literature. 2. Recommend improvements to the EA processes and draw lessons from the ON case for the consideration of other jurisdictions. Evaluation Process 1. Chose criteria ? 14 primary criteria (Wood 2003) ? Subcriteria from Wood (2003) and Lasswell (1971) 2. Gathered information ? 6 key informant interviews ? Published literature, policies, legislation 3. Assessed criteria and formed Recommendations

May 1, 2008