Search Documents

By G. W. Harris, P. Mousset-Jones, J. Daemen

"To minimize ore dilution induced by blast movement in surface mines, it is necessary to quantify such movement. This will enable more accurate location of the grade boundaries beneath the surface of a blasted rock pile before excavation. A method has been developed and tested to accurately measure the direction and magnitude of subsurface blast movement. This technique uses a cesium vapour gradiometer and a real-time, differentially corrected GPS system to locate pre- and post-blast position of magnetically enhanced target objects placed within blastholes inside a bench. The procedure developed does not require the blasted rock to be disturbed, and the movement information is available within a sufficient time to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m, with the overall accuracy being measured as ±1 m (horizontally) and ± 1.2 m (vertically). IntroductionOre dilution is a critical concern for many mining operations. In some instances, it may be the cause of considerable mineral loss. Where the mineralization is finely grained, sedimentary and disseminated in nature, and exhibits no clearly defined visual ore/waste boundary, there is a heightened possibility for ore grade dilution. In most modern open pit gold mines, it is economically desirable to minimize dilution in the production process through the practice of selective mining by defining pre-blast ore digging boundaries, called digging polygons, on the preblast bench area. The polygons’ positions are defined by sampling the production drill holes, with the resultant assay and survey data being used to estimate the areas of specified grade content within the bench. Once the ore is blasted in the bench, the pre-blast locations of these digging polygons are flagged as designated areas on the broken ore pile. The purpose is for the loader operator to be able to recognize which areas of blasted rock are to be sent to the appropriate processing facility or to the waste dump."

Jan 1, 2001

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By T. Prietl

Metallurgical vessel linings are multilayered, consisting of refractory bodies, insulation materials, joints, and additional space to control for thermal expansion. A unique biaxial hot testing press (BHTP) was installed at the RHI Refractories Technology Center Leoben, Austria to enable the three-dimensional behaviour of complex vessel lining segments to be investigated under simulated service conditions. Using the BHTP, the heat up and thermo-mechanical behaviour of magnesia chromite brick lining segments with and without mortar filled joints were examined. The results obtained during the initial heat up provided validation of CFD modelling of the lining system. In addition, after the heat up and under steady state conditions, the lining behaviour during deformation-controlled compression and relaxation was examined. These analyses generated important data regarding the stiffness, joint compressibility, and brick damage of the lining segments after cyclic loading and unloading as well as the benefits of using mortar joints in the lining. These investigations were performed in collaboration with the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals, University of Leoben, Austria. The BHTP has been operational since November 2004 and is providing information regarding the thermo-mechanical behaviour of different lining segments.

Jan 1, 2007

By I. Lazaro Roche, J. Brunner, J. Busto, X. Martin, J. B. Decitre, S. Gaffet, F. Hivert

"Muon tomography allows investigating the subsurface. Muons being penetrative, the attenuation of the muon flux depends on the quantity of matter the particles travel through, hence on the rock density and thickness. For the Temporal Tomography of rock Density using Muon Measurements (T2DM2) project, the muon flux measurements are performed in LSBB URL (http://www.lsbb.eu) in order to study the hydrogeological processes in the unsaturated area of Fontaine-de-Vaucluse karst aquifer. The suitability of the muography for this study is here numerically demonstrated. In parallel to these simulations, muon flux measurements are carried out in the LSBB galleries by means of a set of four scintillator tanks and Micromegas detectors are developed. These detectors, here described, are adapted for underground and confined spaces as well as other environments. Their performances are particularly interesting and should contribute to the expansion of muon tomography in new application fields. INTRODUCTIONMuon tomography or muography is a method to image large volumes by measuring the absorption of cosmic ray muons. It uses, in a passive way, a natural radiation source: the muons which are charged particles produced in the atmosphere. Primary cosmic rays interact with atmospheric nuclei and produce a huge number of secondary particles, including muons. Due to their important mass compared to electrons, they are highly penetrating, reaching several hundreds of meters below the surface. Their attenuation depends on the quantity of matter they cross. That's why they are used to investigate the subsurface, muon absorption measurement allowing to estimate the in-situ density of the rock.Georges (Georges, 1955) proposed in 1955 to use the muons in order to study the density variations caused by the overburden over an Australian tunnel. In 1970, Alvarez (Alvarez, 1970) imaged the internal structure of Chephren Pyramid thanks to this method. The muon tomography has been particularly developed for volcanology (Nagamine, 1995; Tanaka, 2007; Lesparre, 2010; Carloganu, 2013) over the last twenty years. Since the beginning of the 2010's, a growing amount of projects that proposed to use the muons in various fields get underway: the CO2 storage (Kudryavtsev, 2012), the exploration of Mars (Kedar, 2013), etc."

Jan 1, 2015

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By A. W. Davis

Sapping and mining have constituted an important part of siege operations ever since powder came into general use in Europe. Before this period, famine was the main weapon in the hands of the besiegers, and the history of the middle ages is replete with accounts of sieges lasting two and three years. With the advent of explosives, a position impregnable to assault might be readily won by mining under, and blowing up, its defences. The natural offensive against this method of attack is to countermine and stop the attackers underground before their objective is reached. Thus developed the art of military mining. The French and British, in the Peninsular war, were adepts at this method of warfare, and the explosion of a mine and the formation of a breach were the usual preludes to the general assault of a position. In the Crimea, at Sebastopol, the British and Russians did a lot of underground fighting, as the old maps of their galleries, now in the museum at Chatham, will testify. In the siege of Port Arthur, in still later times, the Japanese and Russians were hard at it as well.

Jan 1, 1926

By K. E. Haque

"Radium is selectively leachable from uranium ores with various types of lixiviants. Among a number of lixiviants tried on Midwest Lake uranium ore, KCl provided the highest per cent of radium extraction (60%-65%). Leach results further confirmed that a certain portion of Ra is not amenable to KCl leaching. More than 99% of the dissolved radium could be removed by treating the KCl leach liquor with barite or with radium selective complex resin (XFS-43230 resin of Dow Chemical Inc.) or by precipitating as RaBaSO4. Uranium leachings from the Ra-preleached uranium ores indicate that radium leaching prior to uranium may be applied as an extension to the conventional or alternative (i.e. acid chloride) leaching process of uranium ores in order to yield environmentally acceptable tailings (in terms of radium in the solids).IntroductionAt present, radium is considered as an environmental issue, particularly for uranium ore mine mill operations, rather than a commercial commodity. Radium was once a highly priced commodity ($180/mg during the first great war) but now it hardly has any commercial value. Its principal applications were in the field of cancer treatment and in the manufacturing of lwninous dials for watches. Nowadays readily-available synthetic radioisotopes are finding applications in place of radium.Because of scarcity and high toxicity, further commercial applications have never been explored.Radium was first discovered and extracted from uranium ore by P. Curie, M. Curie and G. Bement in 1898. Radium is widely distributed in nature but in exceedingly minute quantities. It is one of the daughter products of uranium or thorium and its maximum concentration is 3.3 x 10-7 part/part of U(21). Because of its short half-life (approximately 1620 years) in a geological time scale, its occurrence in nature as a distinct mineral is most unlikely.The details of the original radium leaching process developed by the Curies and Bernont are in the literature. This process essentially involved the roasting of uranium ore with caustic. carbonate followed by sulphuric acid leaching. The precipitated RaSO4 and BaS04 were treated with boiling Na2CO3 to convert them into the corresponding carbonates which later were dissolved in HCI. RaCI2 and Ba02 were separated and concentrated from the chloride liquor by fractional crystallization. But, in the course of time several modifications were made or proposed to the original process. Regardless of the process employed 226Ra extraction from the uranium ore was seldom better than 90%, and further as much as 20% 2URa loss took place during the concentration and purification process."

Jan 1, 1987

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By David J. McDougall

"The production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with Les Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivieres (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about Les Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian milieu, but whatever the reason, the other Quebec iron works have been generally ignored. All but one of the Quebec blast furnaces could be described as ""pre-industrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day. Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence River. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces. Five of these, including Les Forges du St. Maurice, were located on or near the St. Maurice River which enters the St. Lawrence River from the north, and two, the St. Francis Forges and the Grantham Iron works were on or near the St. Francis River which enters the St. Lawrence from the south. In a general way deposits of bog iron ore in the St. Lawrence lowlands of Quebec were contained within the limits of the post-glacial Champlain Sea, with many clustered along the flanks of the St. Narcisse recessional moraine which is crossed by the St. Maurice and other near-by streams, and the Drummondville recessional moraine which is crossed by the St. Francis River."

Jan 1, 1999

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By Robert B. Parsons

"This article addresses the relationship between mine evaluation, the tax system, and economic risk. It is based on a paper presented by the author at recent seminars in Moscow and Tashkent on the subject of mine evaluation.IntroductionTaxation can have a strong influence on the feasibility of a mining project. For the most part, because metal prices are determined on a global basis, the mining concern is not able to pass on to its customers any portion of taxes which the concern has to pay. Taxes are a direct charge against the project. The purpose of the article is to highlight the various ways whereby different taxes can affect the financial viability of a mining operation.The first part of the paper identifies different forms of taxation, and the second part of the paper addresses the different forms of taxation in terms of risk analysis and impacts on the mining project. Finally, the third part of the paper makes brief mention of using the taxation system to provide incentives with respect to investment in mining activities."

Jan 1, 1993

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By Donald Brisebois

The mining of high-grade, narrow vein deposits is an important field of activity in the precious metal mining sector. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise dilution, the Thermal Fragmentation Mining Method enables the operator to extract a narrow mineralised corridor, 50 cm to 1 metre wide (according to the width of the vein), between two sub-level drifts. By inserting a strong burner powered by diesel fuel and compressed air into a pilot hole previously drilled directly into the vein, a thermal reaction is created, spalling the rock and enlarging the hole to 80 cm in diameter. The remaining ore between the thermal holes is broken loose using low powered explosives, leaving the waste walls intact. This patented method produces highly concentrated ore, resulting in 400% - 500% less dilution when compared to conventional mining methods. The mining method reduces the environmental affects of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a 2-person team (1 thermal fragmentation operator, 1 drilling operator) maximises the effectiveness of skilled personnel, and increases productivity and safety. The Thermal Fragmentation is currently employed in 3 mining operations in North America.

May 1, 2010

By Yves Pépin, Sylvain Lefebvre, Dimitrios Filippou, Guillaume Hudon

"Titanium dioxide pigment plants using the so-called “chloride process” produce considerable amounts of chloride waste, which contains predominantly iron chloride. In most cases, this waste is dissolved in a weak hydrochloric acid solution and then neutralised. The metal content of the waste is dumped as hydroxide sludge, while its chloride content is lost in an effluent.Rio Tinto Iron & Titanium has developed a new proprietary process whereby pure metallic iron and chlorine gas are recovered from chloride waste by electrolysis. This process uses a two compartment cell separated by an anion exchange membrane to prevent iron cycling between its trivalent and divalent valence. The cathode is made of titanium Grade 7, while the anode is a dimensionally stable one of the type “metal–mixed metal oxide” (MMO) for the evolution of chlorine gas. The catholyte is concentrated and pH-adjusted iron-rich chloride solution originating from chloride waste. The anolyte is recirculating solution containing alkali or alkali earth chlorides such as MgCl2, NaCl, etc. Current efficiencies above 90% can be achieved at temperatures about 80°C using catholyte solutions almost saturated in iron chloride and other chlorides.In this paper, we discuss the details of this process, and how this could be integrated within a chloride pigment plant for the treatment of chloride wastes."

Jan 1, 2016

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By G M. Thorpe

This paper discusses mine research at Inco, giving specific examples of research projects which illustrate the approach to mining problems. The first example covers the development of a new mining method, "undercut and fill," which was originated for mining badly broken-up pillars, but which is now rapidly replacing the square set method of pillar recovery. In the new method, ore is extracted in a series of successive horizontal cuts, progressing downward, a cut being completely mined and filled before the cut below is started. In the second example, improvements to the "cut and fill" method of mining are discussed. These improvements are the result of improved techniques and improved equipment, etc., with, in many cases, the former being made possible by the latter. The advances made have permitted the use of the "cut and fill" method at much greater depths than before. The third example is presented to illustrate research undertaken to obtain the earliest maximum advantage of the introduction of a new piece of equipment or material. For this purpose, the development of the "Under-ground use of AN /FO Blasting Agent " has been selected. Work on this project started in May, 1960, at a time when there was very little in-formation regarding the potentialities of AN /FO for underground blasting, either primary or secondary. By the end of 1961, AN /FO made up 64 per cent of the explosives used under-ground at Inco mines.

Jan 1, 1963

By Helmut Ehnes

Over 330 million accidents at work happen world wide every year, only counting those leading to more than four days absence. More than 350,000 end fatal. Two million people more die every year due to work-related diseases. To sum this up: around 2.4 million people die every year because of work conditions. Among many risky industries, mining stands out. While mining represents just 1% of employees globally, it unfortunately represents 8% of all occupational fatalities. Mining operations go along with a variety of hazards. Not only in large operations, as they first come to mind, but also in the manifold small scale mines, with an estimated 13 million labourers worldwide exposed to substances such as dust, mercury and other chemicals, while also dealing with poor ventilation, inadequate space and overexertion. But is the number of severe accidents and diseases inevitable or can we change this situation? We can make mining sustainably safer, but we need a successful strategy to do so. A high potential lies in Vision Zero. Vision Zero is a prevention strategy for a safe future without fatal or serious occupational diseases, work accidents and traffic accidents. First defined as early as in the 19th century by Eleuthère Irénée du Pont, its very successful elements were adopted by many European countries first aiming at road safety, then extended to safety and health at work. Vision Zero?s holistic elements cover technology, workplaces, rules, and people as fields of action. By focussing on severe and fatal accidents, its application increases the level of safety and health overall.

Aug 1, 2013