Search Documents

By J. J. Mather

NEPHELINE SYENITE is a feldspathic rock resembling granite in texture and hardness but it is white in colour and contains appreciable quantities of the mineral nepheline, the result of a silica deficiency. It is relatively common, with known occurrences in Russia, Scandinavia, India, Canada, United States, and other parts of the world. However, the particular deposit being mined at Nephton, Ontario, by American Nepheline Limited is unique in its remarkable uniformity and low content of iron bearing minerals, both qualities essential in a ceramic raw material. The orebody is a pear-shaped mass over five miles in length, up to a mile in width, rising in three prominent ridges as much as 300 feet above the surrounding lakestudded terrain. American Nepheline holdings, consisting of 2,200 acres, comprise some 85 per cent of the total mass.

Jan 1, 1957

By G. Stafford Whitby

N ATURAL gas is found in several provinces of Canada, particularly Ontario, New Brunswick, and Alberta. The largest producer is Alberta, and there the most important field is the Turner Valley, where some low-gravity crude oil and naphtha are associated with the gas. Last year there was produced from the Turner Valley field an average of 3,462 barrels, or about 450 tons, of oil a day. The gas flow from the wells in this field bears such a high ratio to the oil which comes from them that, despite the enforcement of a measure of conservation, it amounted to the vast quantity of 6,000 tons a day, or more than 2,000,000 tons a year. Prior to the application of any conservation measures, the gas flow was at one time of the order of 12,000 tons a day. The heat content of one ton of the gas is almost equal to that of two tons of coal. A certain amount, say, 10 per cent," of the gas is used in Calgary and surrounding towns and in re-pressuring the Bow Island gas field, but the greater part of it goes to waste. What are the possibilities of making use of this waste gas, in whole or part? The possibilities of using it profitably as fuel for domestic and industrial purposes have undoubtedly been carefully considered by the Company which now distributes a part of the gas to cities and towns in Alberta. But the relative sparness of the population and the cost of pipe lines makes such possibilities strictly limited. There are, however, distinct possibilities of making use of at !east a part of the gas for the production of a variety of chemical products and of liquid motor fuel. The present paper is devoted to outlining some of these possibilities. About three-quarters (by weight) of the Turner Valley waste gas consists of methane, the lightest and, chemically speaking, the simplest of hydrocarbon gases. The remaining quarter consists of heavier hydrocarbon gases-ethane, propane, and butane. Formerly, naphtha was separated from the well gas by a simple process of self-refrigeration. The gas coming from the wells at a pressure of, say, 1,200 to 1,800 lb., was passed through simple cylindrical vessels fitted with baffles and known as 'separators'. The pressure was allowed to drop to, say, 300 lb. in the separators, and the cooling effect secured by this expansion brought about separation of the naphtha. The naphtha thus obtained was 'wild', that is, it had a high vapour pressure owing to the presence in it of dissolved and liquefied gas. In order to reduce the vapour pressure to a level at which the naphtha could be shipped, this gas was removed either by distilling it out through a 'stabilizing' column or, according to the practice at many wells, merely by allowing the naphtha to 'weather' in open tanks (heated by coils if necessary) until the gas had been driven off in to the air.

Jan 1, 1936

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By Chi Zhang, Junyi Wu

"The use of permanent stainless steel cathodes for electrorefining and electrowinning of cathode copper had been introduced to the market long time ago and now is a well-accepted technology worldwide. During the last decades, the Chinese copper refinery industry had been growing rapidly and many large scaled production plants had been built. In the modern refineries, permanent stainless steel cathodes are introduced and used instead of traditional starter sheets. The most common steel grade used is austenitic stainless steel S31603 (316L/1.4404), while both S30403 (304L/1.4404) and N08904 (904L/1.4539) have been used depending on the actual working conditions, especially with regarding corrosion environment. While 316L permanent cathode functions well in many plants, different kind of problems, such corrosion and deformation, have been reported. There is therefore an increased need for more suitable material. New stainless steels, such as duplex stainless steels, with better properties have been tried and introduced into the application of permanent stainless steel cathode with satisfied results. The article introduces first the Chinese copper refinery industry and properties of duplex stainless steel in general, and then describes the development of using permanent duplex stainless steel cathode, including the actual working conditions, production of cathode sheets as well as the experiences of application in details. After more than one year’s usage, the advantages of permanent duplex stainless steel cathodes are clear seen.INTRODUCTIONChina has become a major player in the international copper market, accounting for around 40 percent of global refined copper demand. Despite the slowdown of the Chinese economy, the consumption of copper products will still increase, but with a medium and/or low growth which will be the new situation for the coming years. The average growth rate is expected to be around 5 percent per annual. In the coming Five-Year plan for National Economic and Social Development a number of initiatives will be finalized which will require massive amounts of copper. In 2015, the expected consumption of copper products will be over 9 million metric tons. The main driver of the consumption is the electric power industry which accounts nearly the half of the total consumption; followed by cooling application with 15% and transportation with nearly 10%, see figure 1."

Jan 1, 2016

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By Adriana Ramirez, Bradford C. Wesstrom, Blanca Olave

The Freeport McMoRan El Paso Copper Refinery optimizes electrolyte quality using a number of systems. The facility controls copper, arsenic, antimony and bismuth using electro-winning cells within the Tank House and Nickel Carbonate Plant Liberator Circuit (NCP). The NCP manages sulfuric acid content utilizing recycled electrolyte in the slimes autoclave as well as operation of the Acid Purification Unit, APU. The El Paso Refinery removes common sulfates using metal hydrolysis with sodium carbonate. Finally, a Mechanical Vapor Recompression, (MVR), at the water recovery plant removes sodium sulfate generated by the NCP. This paper will provide a summary of these operations. INTRODUCTION In the mid 1920’s Nichols Copper Company, in Laurel Hill, New York, recognized the need for a modern copper refining facility in the southwest. Because of the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the ideal location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Water is a precious commodity in the desert southwest, making conservation of this natural resource an important goal for the El Paso Operations. In the 1980’s, work on the treatment of slimes was improved through the use of pressure leaching of the refinery slimes using an autoclave. Due to the high tellurium content in the leached slimes solution, it was crucial to implement a method for its removal before the solution returns to the tank house electrolyte. A copper telluride cementation operation was installed for tellurium recovery and the ability for the recycle of the leachate and wash water to the refinery electrolyte. In October of 1997, ground was broken for the construction of the water recovery plant using an MVR to reuse process water, reducing water consumption by 25%. In 2002, electrolyte purification was further improved with the installation of an Acid Purification Unit, (APU) (Sheedy, Pajunen, & Wesstrom, 2007). The APU recycles 90% of the acids (both sulfuric and arsenic acids) back to the tank house electrolyte. The solution that passes through the APU is treated with soda ash to precipitate metals out of solution as carbonates and generates a sodium sulfate solution. This sodium sulfate solution is easily processed in the new water recovery plant, where the majority of the water recycles back into the plant as pure condensate. In 2012, the power plant at the refinery upgraded its Reverse Osmosis System to provide RO water to the tankhouse. This insured that the refinery would not have to bleed electrolyte for metals contained in well water such as: calcium, magnesium, iron and sodium chloride.

Jan 1, 2019

By Seungyeol Lee

Currently, a new construction method using a robotic system is widely spreading in construction sites. This study is related to the design of glazing robot?s teach pendant which can improve convenience of handling and hence improve the productivity through the efficient interaction between an operator and a robot while doing glazing works, e.g., curtain wall installing. The suitability of selection and arrangement of control switches was assessed according to mechanical motions of a glazing robot, and design guidelines for improving convenience and productivity were drawn up through questionnaires carried out by site operators. To verify the proposed design guidelines, working time comparison of the proposed teach pendant and the existing teach pendant was executed.

Aug 1, 2013

By David Davidson

Overview- Points To Be Addressed ? Review the building blocks of a successful and vibrant industrial economy ? China?s current position in the global economy ? China?s voracious appetite for raw materials ? Distortion in import/export trends ? Areas of strategic importance for China - Steel and its components - Agriculture self sufficiency - Energy now and for the future ? Do current valuation techniques fairly value ?strategic? assets? China ? The Economical Miracle - Massive shift in population from rural to urban - ?Middle class? growing rapidly, hence strong consumer growth - China is the manufacturing center for the world ? cheap labour and - modern facilities - Infrastructure build out ?US$585b stimulus package and 5 year plan - Rail ? 30,000 kms of new track planned by 2020 - Power ? 50% capacity increase, including 35 nuclear reactors - 100 major new airports - State of the art process and manufacturing facilities - Port capacity ? 100m TEU capacity increase by 2020 Class 1 national highway ? 35,000 km?s by 2020

May 1, 2010

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By A. P. Craig

"I HAVE BEEN looking forward to addressing this particular audience about Trans-Canada Pipe Lines because you men, more than most, understand the problems of the pioneer. Trans-Canada Pipe Lines qualifies as a pioneer on two counts: it is certainly pioneering a completely new industry in Canada -the long-distance transmission of natural gas -and it has at least a few of the problems that are expected and normal to any pioneering venture.This morning, I’m going to try to give you a sketchy picture of our project and a brief report on its current status and our progress to date; and then a broad picture of Canadian markets for natural gas.The physical characteristics of the Trans-Canada Pipe Lines project have been discussed so often that I am not going to take the time today to quote a lot of statistics on pipe sizes, miles, tons of steel, etc. Suffice it to say that this project, estimated to cost approximately $350,000,000, will be the longest large-diameter gas pipe-line ever built anywhere.Let me try to paint a broad picture of this great national project, using only a few basic 'round' figures.First, it involves exploration for and development of the natural gas fields in Alberta and other provinces -the cost of which will run into hundreds of millions of dollars.Then comes the gathering, stripping, and cleaning of the gas before it can be delivered to Trans-Canada. This will cost close to $100 million.Next we have the Trans-Canada Pipe Lines project for transmission of the gas to Eastern markets -estimated to cost $350,000,000 during the first three to four years and making natural gas economically available to one-half the population of Canada."

Jan 1, 1955

By L. R. Wilkinson, W. J. Howarth, G. J. Wenk

Over a period of three years, a cooperative program in Australia has resulted in the development of radioisotope immersion probes for the on-stream analysis of mineral slurries. Two basic probe types are now available on a commercial basis - fluorescence and absorption probes - and within each type there are a number of variations so that optimum sensitivities can be obtained for elements with atomic number greater than titanium (22), thus covering most metals of interest to modern metallurgy.

Jan 1, 1973

By M. Al Mukhtar, D. Hoxha, X. Brunetaud, D. P. Do, C. Auvray, L. Michel

"Mechanical behavior of rock joints is often the key factor governing the response of complex structures constructed in fractured rock masses such as underground openings or of objects assembling various stones blocks such as historical building walls or damaged marble statues. This paper aims at developing a theoretical model to describe the behavior of fresh joints based on the description of their morphology. The main idea of the model is to establish a link between the effective contact surface of joints and the frictional coefficient. Beginning from a chosen level of joint surface description where a joint is considered as “smooth”, the model describes the added friction with respect to the increase of the contact surface of the joints and the distribution of stress in these contacts. The model developed initially for asperities with regular geometry is firstly compared with existing models and then applied on fresh artificial joints. For that, healthy artificial joints have been characterised using in one hand classical CNL shearing tests and in another hand the morphology of joints. The joints surfaces are digitized before testing using a high resolution laser scanner (Konica Minelota Vivid 910) allowing to obtain a precision up to 10µm. From these scanned surfaces the morphology of joints is characterised on the profiles running in the direction of shearing and a mean value of friction is calculated using the developed model. This calculated value is then compared with that obtained from CNL shearing test and a good approximation is notedINTRODUCTIONThe role of the mechanical behavior of rock joints on the overall response of fractured rock masses is well established in many fields of engineering activity going from the stability of underground constructions (Souley M, Hoxha D, Homand F 1999), rock slope stability (Einstein H.H. Veneziano D., Baecher GB., O’Reilly K.J, 1983, Jaeger 1971), various rehabilitation of masonry construction, damaged stone artworks restoration (Michel L., Do D.P, Coignard B, Hoxha, 2014) and so on. In the same time the characterisation of the behavior of joints and their modeling is nowadays a dynamic field of research or/and investigations and many alternative approaches have been proposed (Barton, N.R. and Choubey, V. 1977, Tatone, S.A. Bryan, Grasselli Giovanni 2010, William C E. 2007). While empirical relations of shear strength with various parameters of the joint morphology are the most used in practice because of their simplicity (Barton. and Choubey, 1977, Barton 1973, Bandis S., Lumsden A. C. and Barton N. R. 1983) many other models of joint strength are developed based on mechanistic considerations (Haberfield CM, Johnston IW. 1994), multiscale approaches (Yang Z.Y., Di C.C., Yen K.C. 2001, Fardin N., O. Stephansson, Lanru Jing 2001) or micromechanical ones (A. Serrano, C. Olalla, R.A. Galindo 2014) to mention just a few of research trends on rock joints modeling."

Jan 1, 2015

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By John Campbell, William Trahant

"Total Quality Management (TQM) is becoming a reality in the mining industry. Widely adopted in the manufacturing and services industries, TQM has become the operating style of choice in numerous mining companies across the Americas and Australia. Iron Ore Company of Canada, Inco, MSA, Graniterock, Magma Copper, and CRA's Hamersly Iron - all are pioneers of TQM. These companies and others are confronting the challenges of implementing TQM and are managing the changes required of their people and cultures. What these companies are doing, why they are doing it, and how they are successfully managing the changes are the subjects of this paper.Driving the need for change in these organizations are a host of issues, some of which all mining companies are facing. Requirements from customers for ISO 9000 certification is becoming one of the initial motivators for Total Quality Management. These standards, commonly used in manufacturing throughout the European Community (EC), emphasize quality in the processes that create outputs, instead of just the outputs themselves. Iron Ore Company of Canada, for instance, responding to the requirement of one of its customers, British Steel, has become one of the first mining companies to meet the quality standard. Suppliers who meet the standards are highly desirable to customers who are themselves operating under the ISO or their national quality guidelines."

Jan 1, 1995

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By Robert A. Gault, T. Scott Ercit, Mehmet F. Taner

"Abstract -Vanadium mineralization occurs in oxide-rich horizons within the layered gabbro zones of the upper parts of the Bell River Complex, Matagami, Québec and the Lac Doré Complex, Chibougamau, Québec. The vanadium-rich horizons are well defined on the ground and in aeromagnetic surveys by their high magnetic susceptibility; consequently, magnetic susceptibility can be an indicator of vanadium mineralization. The main oxide minerals are ilmenite and titanian magnetite, containing 20% to 70% of volume and the ratio of titanian magnetite to ilmenite is relatively constant, ranging from about 1:1 to 2:1. Their sizes are less than 5 µm to greater than 1 mm to 2 mm, occurring as coarse- to medium-grained subhedral crystals intergrown with cumulate silicate minerals (plagioclase, pyroxene, etc.). Electron microprobe analyses indicate that the ilmenite grains are mineralogically and compositionally homogeneous and have low V contents (average 0.18% equivalent V2O5). In contrast, the titanian magnetite grains are inhomogeneous, consisting of trellisworks of ilmenite lamellae in Ti-poor, V-rich magnetite [less than 2 wt% TiO2, and 1.41% equiv. V2O5 (1.16% V2O3) for 20 analyses]. Thus, the magnetite is the principal ore mineral of vanadium; it hosts vanadium in the form of V3+, not V5+, as is commonly and erroneously reported. We have also devised a flowchart for the beneficiation of vanadium-titanium ores. Sommaire - La minéralisation de vanadium se trouve dans des horizons riches en minéraux oxydés de la partie supérieure des zones de gabbros lités des Complexes de la Rivière Bell, Matagami, Québec et du Lac Doré, Chibougamau, Québec. Des horizons riches en vanadium ont été bien définis sur le terrain et dans les levés aéromagnétiques par leur susceptibilité magnétique élevée; conséquemment, la susceptibilité magnétique est l’indicateur directe du contenu en vanadium. Les principaux minéraux oxydés sont l’ilménite et la magnétite titanifère, contenant 20% à 70% du volume et le rapport de magnétite titanifère à ilménite est relativement constant, allant d’environ 1:1 à 2:1. Leur dimension varie de 5 µm à plus grande que 1 mm à 2 mm, apparaissant sous forme de cristaux subidiomorphes, de grains grossiers à médiums, intercroissant avec la gangue silicatée (plagioclase, pyroxène, etc.) de la texture de cumulat. Les analyses à la microsonde électronique montrent que les grains d’ilménite sont minéralogiquement et chimiquement homogènes avec un faible contenu en V (moyenne 0.18% équiv. V2O5 ). Contrairement, les grains de magnétite titanifère sont hétérogènes, contenant des lamelles d’ilménite en "trellisworks"; ces grains sont pauvres en Ti et riches en V pour la portion magnétite de la magnétite titanifère [surtout contenant moins de 2 wt. % TiO2, et en moyenne 1.41% équiv. (1.16% V2O3) pour 20 analyses]. Ainsi, la magnétite est le principal minerai de vanadium; elle renferme du vanadium sous forme de V3+ et non de V5+, tel qu’il a été communément et à tort rapporté. Nous avons aussi défini un "flowchart" pour la bénéficiation des minerais de vanadium-titanium."

Jan 1, 1998

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002