Search Documents

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

By Dale Verran, Jared Orynik, Chad Sorba, David Bronkhorst

Denison Mines Corp. (“Denison”) has a 90% interest in the Wheeler River Uranium Project (“Wheeler River”) located along the eastern edge of the Athabasca Basin in northern Saskatchewan between the Key Lake mill and the McArthur River uranium mine. The project is host to the high-grade Phoenix and Gryphon uranium deposits, discovered by Denison in 2008 and 2014 respectively, which include combined Indicated Mineral Resources of 132.1 million pounds U3O8 (1,809,000 tonnes at an average grade of 3.3% U3O8). The Pre-Feasibility Study (“PFS”), completed in accordance with NI 43-101 in September 2018, is highlighted by the selection of the In-Situ Recovery (“ISR”) mining method for the development of the Phoenix deposit, with an estimated average operating cost of $4.33 (US$3.33) per pound U3O8. Phoenix is the highest-grade undeveloped uranium deposit known globally, including Indicated Mineral Resources of 166,000 tonnes at 19.1% U3O8 for 70.2 million pounds U3O8. The paper aims to provide a summary of Wheeler River and an overview of the proposed development of the Phoenix and Gryphon deposits according to the PFS completed for the Project. Further details regarding the PFS, including additional scientific and technical information are described in greater detail in the NI 43-101 Technical Report titled "Pre-Feasibility Study for the Wheeler River Uranium Project, Saskatchewan, Canada" dated October 30, 2018 with an effective date of September 24, 2018. A copy of this report is available on Denison's website and under its profile on SEDAR at www.sedar.com and on EDGAR at www.sec.gov/edgar.shtml.

Jan 1, 2020

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By G. W. Norval, V. G. Papangelakis, G. A. Moldoveanu

Smelting has been the primary method of treatment for refractory copper sulfide concentrates such as enargite (Cu3AsS4), but the pyrometallurgical processing generates elevated levels of volatile arsenic. The present research investigates a novel hydrometallurgical process of oxidative dissolution of enargite at ambient conditions in the presence of chlorine dioxide (ClO2), a very powerful oxidant generated in solution by the reaction between a strong acid (HCl or H2SO4) and sodium chlorite (NaClO2). The effects of initial oxidant concentration, particle size, agitation speed and temperature on dissolution kinetics and copper extraction were investigated. It was found that a stoichiometric ratio of ClO2:Cu3AsS4 = 9:1 were needed to completely and congruently dissolve the mineral with fast kinetics (<15 minutes) under ambient temperature. The dissolution extent (metal extraction) increases with increasing ClO2 concentration and decreasing particle size of solids, but is not influenced by temperature or agitation speed.

Jan 1, 2014

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012

By J. Lui

At its Copper Cliff Smelter, bulk nickel and copper concentrate is processed in two Inca flash furnaces and Peirce Smith converters to produce Bessemer matte containing 0.6%Fe. After slow cooling and Matte Separation, Bessemer matte is converted into three main products using magnetic separation and flotation technology: (1) a nickel containing chalcocite concentrate (MK); (2) two types of copper containing nickel sulfide (ME and MR); (3) metallics (MYN). MK is further processed in the Inca top blowing bottom stirring MK Reactor to produce semi-blister copper containing ~4%Ni and ~3±1 %S. The semi-blister copper is then purified in the multi-purpose vessels (MPV) to produce blister copper by reducing Ni, Fe and S content through oxidation. High melting point NiO is formed inside the MPVs. The accumulation of solid NiO and other oxides requires periodic cleaning by adding reductant and furnace matte, a unique process called "washout" at Inca. For many years, the reductant used for the "washout" process has been 15%Si Ferro-silicon. With increasing cost and limited suppliers for 15%FeSi, alternative reductants were pursued. This paper summarizes the development and commercialization of new alternative reductants for MPV "washout".

Jan 1, 2007

By A. G. Eccles

Western Mines&apos; milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine&apos;s location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines&apos; alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977

By J. D. Christian

WHEN mining development began in the Kirkland Lake camp, twenty-five years ago, there was very little information obtainable from surface showings as to the nature of the ore deposits. A length of almost a mile of the main &apos;break&apos; lay under the south arm of the lake, and elsewhere most of the outcrops were covered with glacial drift. Shafts were sunk on ore-bodies of uncertain value, either on the outcrop of the veins or-because of the lake to the north-in the south or hanging-wall. In the second year of the camp&apos;s development, the Great War broke out and retarded progress for its duration. He would have been a real optimist who, in those early years, could have foreseen mining at depths of more than a mile.

Jan 1, 1939

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson&apos;s ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013

By Jun Xiao, Xiaodong Li, Chunming He, Daixiong Chen

"Benzohydroxamic acid with double dentate can react with copper to form cyclic hydroxyl oxime acid copper chelate, indicating a good selectivity for copper oxide minerals flotation, especially for malachite. The flotation results of the pure malachite mineral show a strong synergistic collecting effect between hydroximic acid and xanthate at a ratio of 3.5:1, achieving a malachite recovery of 95.5% when certain sodium sulphide is used as a sulphidizing agent in the optimal pH range. Thanks to the synergistic collecting effect, the flotation recovery of malachite of a real refractory ore flotation ,can reach over 92% under the optimum condition, a 12% higher than the recovery achieved with the conventional collectors. In industrial application, the flotation of the copper oxide minerals is improved , leading to a high efficiency utilization of copper oxide resources.INTRODUCTIONBeneficiation of copper oxide ore is one of the recognized challenges in mineral processing industry. Copper oxide ore is a vital component of copper resource in the world, which has abundant reserves. Majority of sulphide deposits has oxidized zone on the top, and some deposits are oxidized to become the large and medium-sized oxide deposits (Willam & Chavez, 2001). Most copper oxide ores have problems in processing such as high slime consumption, poor floatability, complex ore property and low flotation recovery, so it is of great significance in beneficiation of copper oxide ores to develop an efficient collector, especially for malachite (Fu & Gu, 1997; Wen, 2010; Riet, Kier & Elford, 1980). At present, sulphidization-xanthate flotation is the most important method for treating copper oxide ore. In recent years, due to the decreasing ore grade, the utilization of refractory copper oxide ore draws more and more attention (Zhou, 2003), except for sulphidization-xanthate method, chelating flotation method (Lu, 2009), chemical beneficiation method (Lenormed, Salman & Yoon, 1979), microwave radiation flotation method, hydrothermal sulphidization-flotation method (Mao, Wen & Fang, 2014) and ammonia leaching of sulphide precipitation-flotation method (Lekang, Stevik & Bomo, 2003) have occurred."

Jan 1, 2016

By L. Xia, B. Hart, G. Gingras, M. Furlotte

Plant and laboratory test work was performed in order to optimize a copper/zinc flotation separation circuit at Matagami concentrator, Canada. The testing identified a significant difference between the laboratory testing and the plant flotation, particularly for the sphalerite recovery in the rougher copper concentrate. Tests indicate that sphalerite recovery of the flotation concentrate in the laboratory testing was significantly higher than in the plant. The ToF-SIMS surface analysis identifies surface species responsible for the discrepancy in Zn recovery. It shows that sphalerite flotation is in response to the collector attachment and a significant enrichment of Cu on the surface of sphalerite grains. A comparative surface chemical analysis was performed on both sphalerite and chalcopyrite grains from the plant flotation and laboratory testing in order to identify surface species variability between the two testing. Two significant observations were revealed. First, there is considerably more hydrophilic iron oxyhydroxide on sphalerite surface from the plant flotation sample relative to those from the lab testing. The secondary coating likely completely or partially passivates sphalerite surfaces, reducing Cu enrichment and hence sphalerite floatability. Secondly, comparing the surface chemistry on sphalerite and chalcopyrite, the hydrophilic iron oxyhydroxide species have preference for the sphalerite grains relative to chalcopyrite. Despite numerous studies on the effect of galvanic coupling during grinding, there is limited documented evidence on the effect of the milling environment on the flotation and plant operations. This observation suggests that interaction between sulphide minerals and grinding media have a significant influence on subsequent flotation. This paper discusses the results of a detailed surface chemical evaluation of sphalerite grains from both the plant and laboratory testing in the context of grinding environments and pulp chemistry.

Jan 1, 2016

By V. Shumila, T. Butler

Microseismic monitoring systems listen to a rockmass and record ground vibrations associated with brittle rock fracture. Modern systems record continuously and can identify as many as one thousand small and possibly larger magnitude events occurring each day from induced stress change and redistribution. This paper presents examples of the real time use of microseismic information in mining applications. It shows how alerts can quickly identify large magnitude events or unexpected clusters of seismicity and how seismic re-entry protocol can help to improve safety decisions. Additionally, newly developed advanced analysis techniques applied to mine seismic data sets are shown including the use of clustering methods to see into a cloud of seismic data to identify significant activity and quantify possible planar features. The use of source parameter trend analysis is shown to be a beneficial method for interpreting changes in relative stress levels. Seismic moment magnitude distributions are analyzed using the TGR (Truncated Gutenberg Richter) and TMD (Tapered Moment Distribution) methods to estimate bvalue and expected maximum magnitude. Seismic hazard analysis is shown as a useful way to simplify a dataset and highlight seismic hot spots. The rockmass response to excavation is a complicated spatial and temporal process and microseismic monitoring is a method that can be used to help understand the location and mechanics of failure occurring in the rock ultimately helping to improve safety and productivity at a mine site.

Jan 1, 2015

By W. R. Cowan

The Caledon Outwash is a large deposit of glaciofluvial gravel and sand located 55 km north west of down town Toronto. For the most part it was laid down in a meltwater channel fronting the Paris Moraine about 14,000 years ago. Applying the braided bar model of Eynon and Walker (1974) the principal facies present are imbricated coarse gravels (bar corefacies); crudely stratified, imbricated bar top sandy gravels; and trough crossbedded side channel sands and gravelly sands. Of lesser importance are crossbedded bar front gravels, shallow braided stream facies gravels, and stoss side facies sands and pebbly sands (rare). Lithologically these deposits are characterized by FIGURE I. Geological relationships of Caledon Outwash. Industrial Minerals in Canada up to 95% Ordovician limestone and siltstone in the gravel fraction. A siltstone content of up to 34% requires that beneficiation be carried out for the production of better quality aggregates. Resources remaining are estimated to exceed 500 million tonnes in 3000 ha of the most suitable part of the deposit. Present production is about 4.5 million tonnes per year, shared by several producers.

Jan 1, 1984

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

By Henk Dijkman, Wageningen University, Paula Gonzalez Contreras, Irene Sánchez-Andrea, Jan Weijma, Silvia Vega

"More than 20 years ago, Paques B.V. introduced innovative biotechnologies to recover metals and to remove sulfate from aqueous streams. These technologies find their origin in the exploration of microorganisms involved in the global sulfur cycle. Currently, several sulfur cycle biotechnologies are applied successfully at full-scale. The sulfur cycle is closely linked with the iron cycle, and also the latter offers opportunities for application of innovative biotechnology for the mining industry. Microorganisms of the natural iron cycle carry out reactions that are not feasible by chemical methods such as ferrous iron oxidation with oxygen at pH below 4. Iron oxidation with oxygen can be conducted using microorganisms living at pH between 0.5 and 7 and at temperatures between 0 and 95ºC. Remarkably these microorganisms can also carry out arsenite oxidation at similar acidic conditions and high temperatures. Making use of the extreme features of these microorganisms, Paques and Wageningen University have developed a biological process to precipitate arsenic as scorodite. This biological formation of scorodite is a novel combination of biological oxidation and biocrystallization. Depending on the level of saturation, biological oxidation rates and operational conditions, we could control the formation of the iron precipitates such as jarosite and scorodite. Currently new microorganisms have been harvested from hot springs and rock acid mine drainage to foster the growth of specialized microbial communities with potential high iron and arsenic oxidation capacities and higher resistance to other metals. In our paper we address the ongoing research and development of the bioscorodite process.THE USE OF IRON TO REMOVE ARSENIC In 2015 several environmental disasters related to the release of mine wastewater and tailings occurred. On August 5th, a waste water spill occurred from the Gold King Mine near Silverton, Colorado. A dam holding the tailing pond was damaged and spilled three million US gallons (11 ML) of mine wastewater and tailings, including elements such as cadmium, lead and arsenic, into Cement Creek, a tributary of the Animas River in Colorado. “At their peak, arsenic levels were 300 times the normal level and lead was 3,500 times the normal level” (The Guardian, 2015). In early November, another collapse of a mining dam in the Brazilian state of Minas Gerais spilled between ten and sixteen thousand US gallons of water and sediment after a dam failed from an iron ore mine. Arsenic and mercury polluted the Doce River, arsenic levels were found more than ten times above the legal limit in some places of the river (The Guardian, 2015). Waste production is inevitable during Mining. However, a preventive waste management strategy could have minimised waste production, maximised waste reuse and classified waste by their hazardous degree."

Jan 1, 2016

Arsenic bearing minerals such as enargite (Cu3AsS4) and tennantite (Cu12As4S13), which may associate with major copper minerals such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and bomite (Cu2FeS4), usually report to the copper concentrate in conventional flotation due to their similar flotation properties. Arsenic in a copper concentrate causes environmental problems and also problems in the subsequent pyrometallurgical process. Voltammetric studies were carried out to investigate the oxidation characteristics of enargite, tennantite, chalcopyrite, chalcocite and bomite. Contact angle measurements and micro-flotation tests were conducted to examine the flotation characteristics of enargite and chalcopyrite under controlled pulp potentials. Selective flotation of enargite from chalcopyrite under varied pulp potentials was conducted to investigate the feasibility of arsenic removal from a copper concentrate. The test results indicate that the non-arsenic bearing copper minerals ( chalcopyrite, chalcocite and bornite) were easier to oxidise than arsenic bearing minerals ( enargite and tennantite) in an alkaline solution. Enargite floated well at a potential as high as +0.45 V vs. SCE while chalcopyrite was completely depressed at a potential higher than +0.43 V vs. SCE. Selective flotation revealed that enargite can be successfully removed from chalcopyrite through controlling the pulp potential at +0.30 ~ +0.50 V vs. SCE.

Jan 1, 2007

By H. H. Bird

Kilembe is situated in the foothills of the Ruwenzori Mountains in Uganda. Precambrian stratiform copper de-posits are currently being mined at a rate of 90,000 tons per month. Complex ore structures and variable ground conditions have led to diverse mining methods in the past. New mining areas contain more shallow-dipping, highly contorted orebodies, in heavy ground. Cut-and-fill mining will be practised in the future. The geology, mining and milling are described.

Jan 1, 1968

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada&apos;s iron production was 1.85 per cent of the world&apos;s output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada&apos;s iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957

By R H. Hallam

The Mattagami mining district encompasses a favour-?able belt of folded Keewatin-type rocks, with intercalated sediments and intrusives of late Keewatin age. This environment has been subjected to periods of basic and acidic intrusion. The orebodies lie within the fold structure and are associated with faulting and shearing of considerable magnitude. The No. 1 orebody contains 60 to 70 per cent massive sulphides. The minerals, in their order of abundance, are generally: pyrite, sphalerite, pyrrhotite, magnetite and chalcopyrite. It is evident that the broad geological structure of the district is amenable to ore deposition. There are two ? prominent linear expressions which comprise this broad structure. Both strike directions lie at the edge of, or are related to, a complex gabbro-anorthosite-peridotite zone. The fact that eleven of the ore zones discovered to date coincide with the broad structure indicates its over-all importance. It is estimated that the production from Mattagami Lake Mines will be in the range of 600 to 700 tons of zinc concentrate and 70 tons of copper concentrate per day.

Jan 1, 1964