Search Documents

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973

By B Tadesse, L G. Dyer, K Ward

The Golden Mile ore deposit in Western Australia is one of the largest gold telluride deposits in the world. Approximately 20 per cent of the contained gold in the deposit is present as gold telluride minerals, the most prevalent being calaverite (AuTe2) and petzite (Ag3AuTe2). Telluride mineralogy in the Golden Mile orebody is fine grained and complex having formed due to hydrothermal deposition in the late paragenetic sequence. Nineteen tellurium bearing minerals have been identified including gold and silver as well as mercury, lead and nickel tellurides (Shackleton, Spry and Bateman, 2003). Extensive work has been completed on the flotation of gold, gold-silver alloys and gold ores however there is a lack of information detailing the difference between flotation of native gold and individual gold minerals (Dunne, 2016). Studies on the flotation behaviour of gold ores have focused primarily on the flotation of free gold and refractory sulfides (Teague, Van Deventer and Swaminathan, 1999).

Aug 24, 2022

By Sulanto J, Talonen T

In the mid 1960's Outokumpu considered building a lead Flash Smelter on the basis of Flash Smelting technology developed first in the late 1940s for smelting copper concentrates. Pilot scale tests were carried out and the process was found technically sound. The project was however not economically viable under Finnish conditions and it was cancelled. In 1981 pilot plant tests were restarted after many enquiries from the primary lead producers. All the know-how and development made in copper and nickel smelters was applied to the Lead Flash Smelting process and the tests were successful. Outokumpu has so far tested several types of lead concentrate with lead contents ranging from 28 to 75 per cent. The concentrate is oxidized and smelted to metallic lead and slag directly in the Flash Smelting Furnace using high oxygen enrichment of tonnage oxygen. Fossile fuel is used in the Flash Smelting Furnace in cases when the feed material does not contain enough latent heat to smelt the furnace products even though pure oxygen is used for oxidation. Thus the process results in a low consumption of extraneous energy. Use of oxygen results in a small gas flow but it is rich in sulphur dioxide. The gas treatment facilities and sulphur recovery plant will be small in size and low in investment cost. The process is flexible and can produce stable quality of products from different types of raw materials. Quality of lead bullion especially the sulphur content can be regulated over wide a range, from 0.1 per cent upwards according to the needs of the refinery.

Jan 1, 1984

Coal water mixture (CWM) is a mix of finely ground coal with water and a small amount of chemicals. It is a new way of transporting and handling coal. CWM can be transported, stored and burned like fuel oil in steam generating boilers. It also has some environmental advantages over both oil and bulk coal. A group comprising Ube Industries Limited, Nissho Iwai Corporation (both from Japan) and Coal & Allied Industries Limited has been working in Japan and Australia since 1987 on a joint feasibility study into the production, transport and marketing of CWM from Australia to Japan. The group has been studying the development of a large-scale CWM plant on Kooragang Island at the mouth of the Hunter River at Newcastle, NSW. The project concepts and engineering plans for the CWM plant are well advanced and other studies related to the project are continuing.

Jan 1, 1995

The patented "Epytensic" pump of Minnovation Ltd, a multiple piston pump, is used widely on shearer loaders and by partial high pressure watcr jet cutting strategically in relation to cutter picks not only improves cutting rates, but saves power and increases the life of gearboxes and picks, as well as improving dust suppression. The "Face Side Pump", also a piston pump, located on the ranging arm gearhead has advantages over gateroad pumps and shearer body pumps. The "Extraction Drum", hydraulic air mover system, linked with the above innovations and high pressure water, have further advantages in methane and dust removal. Some modifications providing these systems need workshop applications but most are possible underground with minimal changes to shearer profiles and advantages of minimising hosing, along with the other advantages stated.

Jan 1, 1991

By Weller KR

Completely dry or completely wet materials are comparatively easy to screen, but materials with moisture contents between these two extremes can present varying degrees of difficulty. The presence of moisture can impair the performance of a dry screening plant in a number of ways: ò agglomeration of fine undersize particles onto larger oversize particles, resulting in the fine particles being misplaced to the oversize; ò increasing attractive forces between particles that hinder stratification and particle presentation to the screen; and ò blinding of the screen apertures caused by fine moist particles clinging to the screen which reduces the effective aperture size and the open area of the screen. Test work on full-scale screens has shown that the agglomeration of fine particles onto larger particles only occurs once the equilibrium moisture content of the ore is exceeded, and that the quantity of adhering fines present is proportional to the surface area of the larger particles. An -adhering fines screen model has been developed from this work, and by using relationships derived between the model parameters and feed moisture content, the effect of changes in feed moisture on both product quality and operation of iron ore dry screening plants is predicted.

Jan 1, 1993

In current mining practices it is desirable to bring about a substantial increase in both rate of face advance and productivity, thus compelling the mine engineer to consider better and more productive ways of mining. Transportation plays a vital role in achieving improved productivity. This paper focuses on horizontal transportation systems. Horizontal transportation is defined from the shaft station area to the end of the stope cross-cut. Traditionally, horizontal transportation is inefficient in comparison to vertical transportation efficiencies and accounts for a high proportion of South African mine accidents. Thus, the role of horizontal transportation has been investigated in detail, as it offers the greatest chance for improvement. The purpose of the paper is to provide a best practice guideline for the design of horizontal underground transport systems. It is intended that the document be used by mine designers and planners as an aide memoir during the design process and benefit may well be gained from retrofit and reorganisation activity. The paper looks at transport systems suitable for deep level gold mining in South Africa and evaluates such items as management, scheduling, and haulage systems. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2003

Australasian mining companies expect a high standard of professionalism from their metals exploration teams. They also have, increasingly, a global perspective, employing explorationists of diverse cultural backgrounds and operating in diverse environments. Human resource development (HRD) of these professional explorationists needs to address all personal facets of functioning independently and interdependently in a modem working culture, as well as the needed technical competency. Creation of a learning organisation to promote this development is critical. Organisational consultants can support managers and supervisors as mentors facing the wide spectrum of development required by the explorationists; mentorship and guidance counselling can then complement training in the maturing of professionals from technical competence to professional independence and interdependence. Empowerment and clearly stated expectations are keys by which professionals can learn efficiently and effectively.

Jan 1, 1996

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

By McKenzie C, Michaux S

Modern quarrying operations focus attention on blasting operations as a critical component in the overall cost-effectiveness of quarrying. Generally, optimisation of blasting has been linked to the processes of drilling, explosive consumption, secondary breakage, and product haulage to the primary crusher. This approach gives no consideration to the impact of primary crusher feed size distribution on downstream processes, or on the quality (ie shape and strength) of the final product. Blasting operations can be manipulated to produce a wide range of muckpile size distribution. This paper presents the results of studies into the impact of muckpile fragmentation on downstream crushing and screening operations, and includes measurements of primary blast oversize and muckpile fragmentation, together with measurements of size distribution, circulating loads and flakiness for various process streams throughout a quarry processing plant. This paper is an extension of other studies investigating the prediction and control of fragmentation from blasting, and the role of explosive performance in controlling muckpile fragmentation.

Jan 1, 1995

By L Reynolds, N Whetter, S C. Cox

The Reefton Goldfield has had the largest hard-rock gold production (64 t Au) on the West Coast of the South Island of New Zealand, and is currently under renewed development by Oceana Gold. The gold predominantly occurs in variably sheared quartz veins that are associated with zones of tighter, shorter wavelength folds in the host Greenland Group metasediments. The quartz veins typically occur as a series of plunging shoots that align with specific fold limbs or fold hinge zones. Shear zones containing disseminated mineralisation and quartz veins have thickness variations that relate to the angular relationship between the shear and host-rock bedding. Exploration strategies and targeting can be developed around both types of structural control.

Jan 1, 2005

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

The Olympic Dam mineral discovery by Western Mining Corporation (WMC) in South Australia has been shown to contain one of the world's largest known deposits of copper and uranium; gold and silver are also present. Development of the deposit jointly by WMC and the BP Group is awaiting commitment, with planning based on initial production of gold in 1987 and copper and uranium in 1988.

Jan 1, 1985

The methods used by the Anglo American Corporation for analysis of long-term metal markets and prices are described. The principal factors affecting the relationships between production costs and metal prices are analysed. These are firstly the type of market, - speculative or consumer commodity, free market or subject to price control; and secondly the rate of growth of demand for the metal. It is shown that virtually all metals will have relatively low rates of demand growth for the foreseeable future, due to market saturation, increased economisation, substitution and product obsolescence. Metal prices have a clear dependance on production costs, however forecasting future costs is by no means simple; amongst other things, account must be taken of changing exchange rates, inflation rates, and the potential for operating more efficiently. The paper concludes by giving brief assessments of the long-term future for aluminium, copper, zinc, nickel and tin.

Jan 1, 1986

Detailed observations were made for two existing continuous miner and shuttlecar systems. A simple model for the shift average cycle consisted of three time components - delays, mining and transport. Cycle improvement and productivity improvement factors are derived and used to predict the theoretical improvement which the observed cycles could achieve. Various strategies of action ranging from short-term optimisation through to long-term planning for continuous haulage systems are evaluated. High potential for improvement is shown for a wide range of operating conditions. An overview is presented for systems, currently available or under active development, which can accept coal directly from continuous miners and offer continuous haulage to the surface. Systems are broadly classified as mechanical-roof mounted, mechanical-floor mounted and hydraulic transportation.

Jan 1, 1982

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By L J. Reynolds

Gold mineralisation at the Globe Progress deposit is hosted by a geologically complex zone of shearing and brecciation, within a package of deformed metasediments. Mineralisation styles range from quartz breccias and lodes to sheared clay pug zones and disseminated sulfides. A review of the diamond drill core intersections through the deposit indicates that critical hanging wall and footwall contacts can be a combination of sharp or gradational; visual or non-visual boundaries. Approximately 60 per cent of mineralised contacts can be confidently identified visually, particularly where associated with veining, distinct brecciation or shearing, and high sulfide content. However, the gold grade and distribution of disseminated mineralisation can be extremely difficult to estimate visually, with implications for resource estimation and grade control when mining. Using observed drill hole geology and assays, a new geologically based model for the gold mineralisation has been constructed for the deposit to reflect the expected variability of the mineralisation contacts. This new model will constrain resource estimation and also serve to act as a predictive model when open pit mining commences. Nevertheless, careful grade control practices such as drilling, trenching and supervised extraction of ore will be required to maximise ore recovery and minimise dilution during open cut mining.

Jan 1, 2006

The foundation of our industrial welfare lies in the success of our primary industries, and, so far as mining is concerned, it is hoped that for many years it will be a most important primary industry in Western Australia.

Jan 1, 1927

By Nightingale RJ

A column (50 cm 4) provided with a bell charging mechanism and a rectangular perspex insert was used to investigate the inter-relationship between charging pattern, size analysis and velocity profile for a number of charging methods. It is shown that a strong correspondence exists between size distribution and velocity profile for bell charged ore and coke and that decreased coke volumes cause higher pressure drops and increased central flow in beds with "V" shaped layers. It is also shown that a bell charged mixed burden exhibits greater segregation than when it is bell charged as layers and that when uniformly charged the mixed burden shows least segregation and a virtually flat velocity profile. A relationship is derived for "V" profile charges showing the extent of central segregation with furnace size.

Jan 1, 1975