Search Documents

The mineralogy, maero- and micro-textures of Thackaringa ore are simple and have many counterparts among base metal-quartz-siderite vein type deposits elsewhere.The ore consists predominantly of galena, sphalerlte, chalcopyrite, tetrahedrite, and arsenopyrite in a quartz and siderite gangue. Silver minerals, as such, appear to be lacking and silver values are no higher than in other sulphide ores of this type. These features contrast very markedly with those of the A.B.H. Consols Lode which appears to have emanated from the north end of the Broken Hill Main Lode Horizon during high grade regional metamorphism. The Consols Lode has been regarded as of Thackaringa type, and both are regarded as possibly arising from the remobilization of Main Lode Horizon ore. Whilst this may yet prove to be so it appears that the marked differences in mineral composition between the Consols and the Thackaringa types, would require somewhat different modes of regeneration.Thackaringa ore, as well as A.B.H. Consols ore, on this basis, would necessitate the development of a metahydrothermal ore fluid to account for their present apparently hydrothermal (or pseudo-hydrothermal) constitution...

Jan 1, 1967

By M Tessier, M Pahkala, L Sletmoe

The Red Lake mine is one of the richest gold mines in the world. The primary mining methods are overhand and underhand cut and fill. Starting in 2003, Goldcorp initiated an expansion program at the mine. The expansion includes a new 6.55 m diameter hoisting shaft currently under construction. The shaft will be driven to a length of over 2180 m. The shaft will be used as a primary ventilation intake to the mine. In addition to the new hoisting shaft, a return air raise is being driven approximately 1690 m from surface. This raise will be a parallel return to the existing mine infrastructure. This paper describes the ventilation and climatic analyses performed in support of the expansion project. The study included a full mine ventilation survey, in situ rock mass measurements, analysing options related to mine layout, airway sizing calculations, air heating options, and climatic simulations. Specifications were prepared for an air heating system and main and booster fans. Analyses were also performed related to heat in the stoping areas namely caused by auxiliary fans and backfill with high cement content.

Jan 1, 2005

The large, low grade, Kidston Gold Mine in North Queensland has achieved outstanding economies of scale and profitability. The total mineable ore reserve including mined to-date (as at December 1993) was 70.75 million tonnes at 1.54 grams gold per tonne. After nine years of mining, grade control mine production routinely reconciles against mill production and ore reserves to within five per cent of contained gold. The grade control system developed at Kidston is examined in detail, with emphasis on the geological thinking behind the strategies, as well as the development and application of a computerised, graphical production control and reporting system. Reconciliation procedures and results are explained, illustrating the success of geostatistical methods, as a risk management tool, in both ore reserves and production grade control.

Jan 1, 1994

By Dunne R. C

Column flotation is receiving increased interest from both an industrial and research perspective in Australia. The traditional overseas application as a molybdenum cleaning cell is being expanded and a number of new applications as cleaners, scavengers and roughers are emerging in Australia. The success of column flotation has hinged on the new understanding developing from the work of Finch- and coworkers at McGill University, Canada, particularly in relation to scale-up parameters and model development. The aspiring column flotation user in Australia now a has wealth of experience to draw on when deciding on the correct procedure to follow during the process evaluation and plant installation stages of development. However, some aspects relating to column design, such as aeration mechanisms, require careful evaluation.

Jan 1, 1987

By C Mroczek, B Mitchell

Perilya Broken Hill, from its inception, has budgeted for more than 2.0 million tonnes per year from the Southern Operations. This tonnage was planned to come from in excess of 100 stopes per year in a remnant mining environment with numerous mined voids and consequent mining challenges. To mine an average of two stopes per week requires patience, flexibility and detailed knowledge to best manage the potential risks and hazards. The evolution of the Perilya Broken Hill Mine Planning Process has necessitated the establishment of a process to identify and manage these risks during the planning stage in a reliable but efficient manner. This process is to ensure that vital steps for each stope are not missed, and that each personÆs work can be tracked by other members of the team. This paper outlines the planning process from resource to stope closure.

Jan 1, 2005

By Collins D. N

The Olympic Dam Copper Smelter Acid Plant is a hybrid plant capable of producing sulphuric acid from either sulphur burning, metallurgical gases or a combination of both. Commissioning of the Acid Plant on sulphur burning commenced in early April 1988 and commissioning on combined sulphur burning and metallurgical gas commenced in August 1988. During commissioning on sulphur burning a number of acid spills occurred due to balancing of tower flows and control of acid dilution. A number of other significant problems were encountered including failure of boiler gaskets, failure of strong acid pumps seals, the fracture of the teflon dilution water injector and the subsequent failing of the acid circulation pump, tank steel failures and various instrumentation problems. The Commissioning of the Acid Plant on metallurgical gases commenced in August and with the exception of the production of oleum in the boiler economizer was relatively trouble free. Oxygen Plant commissioning commenced in May 1988 and was without significant incident. An outline of the basic equipment for the Acid Plant and Oxygen Plant is presented together with aspects associated with the commisisoning of both plants.

Jan 1, 1989

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994

By Swift D. G

For some time the Electricity Trust of South Australia (ETSA) has been investigating the application of new mining methods and equipment to minimise the cost impact of the steadily increasing depth of mining brought about by the 20¦ dip of the coal seams at the Leigh Creek Coalfield. Exhaustive examination of all suitable mining systems showed that highly mechanised systems involving belt conveyors displayed no eco- nomic or operational advantages over shovel and truck methods. However, the configuration of the Leigh Creek coalfield allows for two quite different approaches to mining by shovel and truck. The current strip mining method involves removing overburden from the highwall in 60 m to 200 m wide strips to progressively expose the coal down dip, and requires all waste to be hauled to the surface. The alternative ter- race haulback method involves opening a boxcut to full depth at one end of the coalfield, then mining the full section along strike and placing the spoil in the mined out area. On a strictly economic basis, the latter is clearly advantageous, but the former has significant less tangible advantages. In deciding between the two methods ETSA is faced with the need to examine the applicability of each method under a wide range of possible future demands on the coalfield, and to assess the importance of many intangible factors.

Jan 1, 1989

By J O. Watson, V S. Vutukuri

This paper presents results of an investigation on acoustic emission characteristics of granite, sandstone and rock-like material in the unconfined compression and tensile tests. Both the acoustic emission signature and stress-stain curve are analysed in the experiments.The experimental results show that different acoustic emission characteristics are observed at different stress and deformation stages in unconfined compression and tensile testing. Extensive and unstable acoustic emission changes may be interpreted as indicating failure of the rock.

Jan 1, 1999

SPOT imagery acquired in May 1986 of the areas that include the Dugald River lead-zinc lode, northwest Queensland, Australia and the Ngwenalekau copper deposit, Botswana has been evaluated and compared with LANDSAT MSS imagery of the same areas. The data have been processed using band combinations, band ratioing, principal components analysis and classificatory techniques and the outputs compared with those of geobotanical, geochemical and biogeochemical data as well as geological information. For both study areas the image processing techniques cited have successfully distinguished discrete vegetation associations related to discrete surficial and bedrock geological units; and, notwithstanding the sharp contrasts between the nature of the geobotanical anomalies that in both areas occur over mineralised bedrock in Proterozoic sedimentary sequences, they have successfully identified the areas of anomalous vegetation over the mineral deposits. Greater vegetational and geological detail is revealed than on outputs generated from LANDSAT MSS data [see Cole, 1977, 1982(a) and (b)]. The additional information yielded by SPOT imagery compared with LANDSAT MSS imagery results from its greater spatial resolution - 20 metres as against 79 metres - and from ti fact that the three SPOT MSS spectral bands - 0.50 0.59um, 0.615-0.68um and 0.79-0.89um - respectivelc cover those sections of the electro-magnetic spectrum in which leaf pigments, notably chlorophyll, absorption for photosynthesis and leaf cell structure strongly influence reflectance. This accords opportunities for the detection of reflectance aberrations caused by stress due to drought and/or metal toxicity as well as for the identification of anomalous vegetation communities of moderate sizr These cannot be accurately discriminated on LANDSA I MSS imagery on which only very large geobotanical anomalies like that over the Lady Annie phosphate deposit in northwest Queensland [Cole, 1977, 1984; Cole and Owen-Jones, 19771 can be detected.

Jan 1, 1988

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By Ogilvie M

South Bulli is the oldest and largest underground coal mine in Australia. Two longwall units are in operation and current production is 2.5 to 3 million tonnes of run of mine product per year with a workforce of 600. Prior to 1984 a workforce of around 1,200 produced 1.5 million tonnes. Advances in technology can. of course, account for some of this gain, but the changes made in the human resources area are also seen as playing a major role in South Bulli emerging as a reasonably stable operation.The human resources strategy adopted recognises the value of the workforce and is aimed at not only fostering cooperation as all levels, but also making employees aware of the direct contribution they can make to the success of the enterprise.

Jan 1, 1991

By Napier-Munn TJ

The Whiten model of crushers is currently being refined and extended at the JKMRC, with particular reference to cone crushers. This paper describes the model as a predictor of crusher power draw, discusses the application of the model, and considers the relationship between power draw and crusher performance.

Jan 1, 1988

By Y Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, aO2-, and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of aO2-, which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions.

Jan 1, 2000

By T Lancaster

The Mount Gordon operation, consisting of the Esperanza open cut mine and the unique Mount Gordon Ferric Leach processing plant, is operated by Western Metals Copper Ltd at Mount Gordon, 125 km north east of Mt Isa. The processing plant treats predominantly the secondary copper sulphide minerals, chalcocite and covellite. The gangue consists of massive pyrite and a range of silicified siltstones. The processing plant utilises a conventional single stage SAG/cyclone milling circuit, followed by low-temperature/low-pressure autoclave oxidation to produce copper in solution. The pregnant leach solution is treated via conventional SX/EW technology to produce copper cathode. Currently the plant is operating at a nominal production rate of 48 500 tpa copper. The Mount Gordon Ferric Leach technology is the worlds first integrated pressure leach/SX/EW process to be used to treat copper sulphides on a full plant scale. In the last six months, July to December 2001, the plant has emerged from a two-year postcommissioning phase to achieve steady state operation. This has been characterised by high plant availability and consistent production performance in excess of the name plate capacity of 45 000 tonnes. Production rates will continue to increase over the next 12 months to over 50 000 tpa via a planned process of incremental improvements. The pressure leach circuit has consistently achieved availabilities exceeding 95 per cent over the past 18 months. Notwithstanding this, the leach circuit still has a much greater requirement for planned maintenance than SX/EW. For much of the Mount Gordon processing plantÆs operating life, the leaching process has constrained production. Recent developments arising from detailed mass and energy balance modelling have now significantly improved leach capability, resulting in the plant bottleneck being shifted to electrowinning. In order to balance the capabilities of the two circuits however, the surge capacity between leach and SX/EW was increased substantially. This effectively de-coupled the higher capability but lower availability leach circuit from the lower capability but higher availability SX/EW circuit. As a result, electrowinning utilisation has increased to in excess of 98 per cent, which is reflected in a higher overall plant throughput.

Jan 1, 2002

The treatment of nickel ores and concentrates and the subsequent processing to recover separate products of nickel and cobalt is one of the major interests at present in the mining industry. The increasing demand for nickel, and more recently also cobalt, has led to increased exploration for ore sources. Major discoveries have resulted in Canada and Australia. These deposits, as well as others already known, are presently being developed and the process technology tested and evaluated for applicability to the different mineralogical types - mainly sulphide, arsenide and oxide laterites. Concentrates may be treated by either hydro- or pyrometallurgical processes, while the nickel laterites are best suited to hydrometallurgical processing. However, if hydrometallurgy is used, once the ore or concentrate is leached the resultant solutions are then amenable to similar separation technologies for purification and recovery of high purity nickel and cobalt products. Solvent extraction, together with other separation processes such as precipitation, can produce high purity solutions of nickel and cobalt. The final products of these solutions may be nickel and cobalt cathodes, metal powders precipitates or salts, depending on the final process of electrowinning, hydrogen reduction, precipitation, or crystallisation Respectively.

Jan 1, 1996

By M D. Rosengren, G Gregor, M F. Young

Over the last 15 years the silver/lead/zinc ore treated at Mount Isa became increasingly complex and lower grade. Metal recoveries dropped dramatically, causing a serious decline in profitability. The ætraditionalÆ response of increasing tonnage to reduce unit cost was unsuccessful, since the additional tonnage was even lower quality ore. A major technical and capital program in the 1990s restored metallurgical performance, but business return was still too low and ore quality continued to decline. In 1996 a new, holistic approach integrated the steps of geology, mining, concentrating, smelting, and refining. Previous assumptions about æfixedÆ and æmarginalÆ costs in mining and processing were shown to be wrong. Detailed analysis showed that some ore sources were reducing profit. This led to a fundamental redesign and downsizing of both Mount Isa and Hilton mines. The result was dramatic increases in head grades, metallurgical performance and plant stability without any capital expenditure. The business is now smaller, but more profitable.

Jan 1, 1998

By Sheard SN, Tucker DH

Sampling procedures are an important aspect of geophysical exploration survey design. It is good practice that the selection of survey parameters ensures that the signal to noise ratio is optimised, while minimising survey cost.Sampling considerations for any geophysical method include the size of the target, scale of observation, aliasing associated with station and line spacing, nature and extent of overburden, and the presentation of data.As a guide to survey design, the specifics are discussed for three geophysical techniques in common use in mineral exploration; these include the magnetic method, transient electromagnetics and induced polarisation.

Jan 1, 1976

The Fiji islands are the world's most ac- cessible Cenozoic remnant arc. They provide occasional subaerial exposures of an arc frag- ment some 750 km long and 80 km wide, or about the size of the NE Japan volcanic arc. The fragment is one part of the former Vitiaz Arc which once connected Fiji to Vanuatu and Tonga. The Fijian portion has the most completely stu- died Tertiary section which contains a history of arc volcanism from the late Eocene to late Miocene (the Early and Mature Arc stages), a rich diversity of subsequent magmatic responses to the most recent episode of arc rifting (Ear- ly Rifting stage), and an example of transition from arc to intraplate volcanism as this rift- ing proceeded (Late Rifting stage). The arc fragment is surrounded by younger backarc ba- sins. The chemical composition of magmas in both the arc and backarc changed with time, but in opposite directions. In the arc, magmas be- came enriched in sialic components from the Early Arc to Early Rifting stages, whereas in the basins the magmas became more similar to mid-ocean ridge basalts (MORBs) with time. In southwest Fiji, the oldest backarc basin has subducted obliquely beneath the remnant arc du- ring the last 3 Ma, resulting in chemically ex- otic calcalkaline volcanism. During the last decade over 150 radiome- tric age measurements and 650 rock analyses, many with trace element and isotopic measure- ments, have been obtained for samples from Fi- ji, Tonga, and the surrounding seafloor (Figs. 1 and 2). These data are summarized, drawing from the publications of Colley and Hindle (1984), Gill et al. (1984), Hawkins and Melchi- or (1985), Kroencke (1984), Malahoff et al. (1984), Scholl et al. (1985) and Whelan et al. (1985), from the specific research papers refe- renced therein, and from the half dozen or so manuscripts currently in preparation by these people and others.

Jan 1, 1987

Large Off Highway Trucks operated in this country are generally of Diesel Electric Drive, this system tends to employ the familiar Electric Wheel. A number of fleets now employ the Traction Motor System as an alternative. An investigation is made of the operation of two such fleets. A brief description is given defining the components and their basic functions in each system. Available life history is presented and system reliability, maintainability and operator reaction is examined. Trlmnnnr rpm rn~r In the past large Off Highway Trucks operated in this country, that is those greater than say 120 tons, have tended to be driven by a Diesel Electric traction system. Although manufacturers are now offering mechanical or mechanical/hydraulic drives in the larger machines comments will be restricted to examining the Diesel Electric System. Since commencing operations in the mid 1960 period Hamersley Iron has made use of the diesel electric drive system using the familiar Electric Wheel. A departure was made at Tom Price with the purchase of the Wabco 3200 Series Trucks. These 235 ton capacity units employed a dual rear axle system with externally mounted motors. In 1976 a

Jan 1, 1982