Search Documents

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008

The Coal Corporation of New Zealand Ltd (CoalCorp) is the largest coal producer in New Zealand, with extensive properties in both the North and South Islands. CoalCorp's North Island operations are kilcmetres to the south of Auckland. opencasts, are located in the catchment wildlife, historical and scenic values. in this catchment is the single most mining operations. centred on Huntly, a town some 80 Five coal mines, four of which are of Lake Waahi, a lake with significant The discharges of mine lodgement water important environmental constraint on Throughout New Zealand the use of water is controlled by a statute called the Water and Soil Conservation Act 1967. All industrial water users are required to hold Water Rights, which are in effect licences to take, use, dam, divert or discharge water. Water Rights are obtained through a legally defined process and any potentially affected party has the per to object to their granting. A special tribunal hears the evidence for and against an application, and issues its decision, which is reviewable in a higher court on Appeal. Rights, if granted, are issued subject to conditions and, in the case of mining discharges, limits would be set on flaw rate, suspended solids concentrations, turbidity, pH and the concentrations of any potential toxicants. This paper presents a case study of an integrated, catchment wide water management plan for Lake Waahi, that was prepared by the author, and others while the author was in the employ of CoalCorp, and its predecessor, State Coal Mines. The author is grateful to CoalCorp for their permission to submit this paper.

Jan 1, 1988

By Nye P. B, Fisher N. H

At the second Empire Mining and Metallurgical Congress held in 1927, the Empire Council of Mining and Metallurgical Institutions was formed and it was proposed that the Council take steps to prepare a "Review of the Mineral Resources and Industries of the Empire." At the third congress in 1930, it was resolved that the proposal to institute the review should be submitted to the Imperial Conference held in 1930. This was done, and the Minerals Committee, of the Imperial Economic Committee compiled, an interimreport which was based on statistics of imports and exports, and did not consider resources and consumption.In 1942 the Institution of Mining and Metallurgy, London, wrote to the Empire Council and stated that it was desirable that the Council should be in a position to take part in decisions affecting the future of the mining and metallurgical industries. The Council communicated with the constituent Institutions regarding the nominations of two members then in England. Subsequently the Mining, Geological and Metallurgical ,Institute of India prepared a review of the mineral resources and industries of India and their post-war development, and the Empire Council forwarded a copy to the Australasian Institute of Mining and Metallurgy and asked if that Institute would submit a review on simjIar lines for Australia. The Australasian Institute arranged that the Australian review should be prepared by...

Jan 1, 1946

By T D. H McGrath, G Wardell-Johnson, E A. Oraby, W Staunton, A R. Bax, J J. Eksteen

"Gold ores often show significant inter-domain variation with respect to the gravity recoverable gold (GRG) content and the leach behaviour of the non-GRG component. Liberation assessment is extremely difficult for gold due to its malleability and the high sampling errors and poor test reproducibility resulting from gold’s high specific gravity and the low metal concentrations that occur in most gold ores. The use of microscopic techniques for the liberation assessment of gold is also impractical due to the high number of sampling errors and high cost of analysis.Curtin University’s Gold Technology Group has developed an online carbon-in-pulp/carbon-in-leach (CIP/CIL) simulation model called SIMCIL, which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach, which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The ILLM characterisation methodology, test work data analysis, interpretation and application of the ILLM test work data are discussed.CITATION:Bax, A R, McGrath, T D H, Eksteen, J J, Staunton, W, Oraby, E A, and Wardell-Johnson, G, 2016. An Integrated Liberation-leach Model and Ore Characterisation Procedure for Gold Ores, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A G. Dempster, B McKeown, S Saydam, J Coulton

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

The Tailings Leach Plant at Chingola employs a Leach/Solvent Extraction/Electro- winning process and contains the largest solvent extraction plant in the world, with design liquor flow rates of 55 m3/min. A pilot plant constructed to provide design data also indi- cated areas of uncertain operating and control performance and led to a decision to model the whole circuit to determine the overall dynamic behaviour and basic operating characteristics. Details of the plant flowsheet are given and the basic physical and chemical' equations required for the simulation defined. Each unit operation is considered separately and details of the mathematical models used for their simulation presented.

Jan 1, 1977

By M Wortley, A Cantarutti, G J. Clarke, C

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS¬ Expert system together with three VisioRockÖ online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS¬ is the first installation to incorporate Metso Minerals Process Technology-Asia PacificÆs (MMPT-AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS¬ logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

The efficiency with which it is expected that a particular coal may be burnt in a power station boiler significantly affects the value of the coal. Consequently many laboratory tests have been developed to provide data on the combustibility of coal. Computer modelling of coal combustion has also provided insight into limits on coal burn- out. Such modelling suggests that burnout of bituminous coal in a power station boiler will be strongly influenced by physical limits on the diffusion of oxygen to the individual coal particles. Coal chemical reactivity appears to be relatively less important. As a consequence of the diffusional limits, significant improvement in burnout is achieved either by producing less large p.f. particles or by providing sufficient furnace residence time to burn the large particles. Field data from a variety of power stations supports these cn.clusions. Burnout was also found to correlate well with volatile content for a number of coals from widely different sources. This is expected as the high vola- tile coals produce less residual char to be burned by the relatively slow heterogeneous Combustion.

Jan 1, 1987

By R B. Venugopal, P Staples

The selection of the mode of transport for moving bulk materials is never a simple task as there are various concerns/considerations applied to the selection of the most practical and cost-effective mode of transport to be used to move bulk materials. This paper examines various alternatives for moving ore from a mine at the top of a mountain to a process plant below (some 5000 m apart and a vertical drop of 650 m). The terrain of the mountain section of the route has added its own specific requirements, resulting in the final selection of a pipe conveyor for this application. The paper further addresses the final selection of hardware used in the implementation of the solution.

Jan 1, 2005

By Piotto P

Pit optimisation algorithms are designed to produce a pit with maximum value, but for certain minerals like iron ore, limestone, coal, etc, it is also necessary that the designed pit contains ore which meets the customer's chemical specifications. This paper describes a technique of using linear programming for blending optimisation and the Lerchs-Grossmann algorithm (as in Whittle's 3D software) for pit optimisation in tandem, to achieve pit designs of targeted grade specifications.

Jan 1, 1996

By Olson H, Kincaid R

The marine portion of the Pacific Basin and Rim constitutes a significant part of the world's surface in which the mineral resources are virtually undeveloped. Indications of substantial resources have resulted in speculation and uncertainty with regard to their potential in the near term. The main issues are centered on the markets for the resource materials, the technology needs for their recovery, and the possible impacts of their development on the environment. While the governments of Japan, France, the Soviet Union, India, China, and Korea are financing new programs in deep ocean mining, the US is consolidating its early leadership by the continuation of NOAA's authority under the Deep Seabed Hard Mineral Resources Act and the Sea Grant Act, Interior's authority under the outer Continental Shelf Lands Act, and by the development of a new Marine Minerals Technology Center within the Department of Interior's mineral institutes program, managed by the U.S. Bureau of Mines. The Center has a Continental Shelf Division (CSD) located in Mississippi, and an Oceans Basin Division (OBD) located in Hawaii. Research and training in the divisions is directed toward the practical aspects of mineral recovery from the nearshore and deep ocean environments with a strong bias for the OBD toward industrial and international cooperative programs in the Pacific Basin and Rim. In terms of resource development, the marine minerals in the Pacific Basin may be favored in some cases, in competition with land sources, by political and environmental considerations.

Jan 1, 1990

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

By Moore J

Gunpowder Copper Ltd is using in-situ leaching to extract copper from the Mammoth sulphide ore deposit in north-west Queensland. To increase metal recovery, ore is fragmented using conventional underground longhole drilling and blasting techniques. Although the upper levels of the orebody had previously been mined by open cut and underground methods, significant reserves of copper existed around old workings. To safely and economically recover this resource, a decision was made to fire the remaining pillars in the upper part of the mine by a single 1.37 million tonne mass blast in February 1992.This paper records the planning, design, and implementation of the Mammoth mass blast. Geological and geotechnical aspects are summarised, to explain the reasons for such a large blast. Drilling, charging and blast initiation are discussed in detail, to show how standard equipment and products were applied to a unique task.

Jan 1, 1992

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

It is a common misconception that the grant of mining tenure, whether it be an Exploration Permit, Mineral Development Licence or Mining Lease, will entitle the holder to access all land within it in order to explore or mine. The ability for miners to access their tenure in order to undertake activities is critical to the industry. While significant time and energy is quite rightly dedicated to resolving native title and cultural heritage issues before the commencement of mining operations, the same cannot always be said for addressing potential impediments that arise as a result of the overlap between mining and other tenures. Miners should be aware of the overlaps that occur with other tenure and the impact of these overlaps on the minerÆs ability to explore or produce from the area. The existence of an overlap with petroleum tenure, nature refuges, national parks, wild river areas or reserves such as aboriginal land leases are all likely to have an impact on the minerÆs ability to access the area and conduct activities. In some instances, such as an overlap with petroleum tenure, Queensland legislation encourages the miner to reach agreement with the holders of the overlapping tenure. However, in other instances, such as an overlap with a national park, mining tenure is unlikely to be granted at all. This paper summarises the impacts and impediments that arise as a result of overlaps of tenure that are likely to affect mining operations. It also provides examples of how these impediments can, if possible, be overcome under Queensland legislation.

Jan 1, 2007

By G Guy, J Summerville

Over the past five years in coalmine slope evaluation the application of 3D modelling has increased significantly as software has become more user friendly but also areas requiring evaluation have become increasingly complex. Often simplistic 2D Limit Equilibrium modelling and analysis has been poorly used to solve slope stability issues by back analysis and subsequent forward predictive analysis. A plane strain condition with slope movement perpendicular to the slope strike is assumed where in reality the problem is more complex. This often leads to a misinterpretation of the failure mechanism because the failure mechanism being modelled in 2D does not generally represent the actual failure mechanism observed in the pit, with 2D modelling often oversimplifying a slope. This paper presents a case study where the initial slope assessment and remedial design evaluation was undertaken as a 2D Limit Equilibrium model which led to an overly conservative and costly remedial solution being implemented. Subsequent modelling of the slope using both 3D Limit Equilibrium and Finite Element methods were able to provide a better understanding of the structural complexities associated and correlate well with slope monitoring data to create a more realistic outcome.

Nov 29, 2022

By H Kim, M J. Sun

In order to reduce carbon emissions from the steelmaking process and achieve carbon neutrality, global steel companies are establishing their own medium to long-term strategies and implementation plans using competitive technological advantages held by each steel company. At this point, Hyundai Steel has formulated a product-oriented carbon-neutral strategy based on innovative processing that makes use of Hyundai Steel’s own strength. Based on our experience in electric arc furnace product manufacturing and blast furnace operation in an integrated steel mill, Hyundai Steel is driving the Hy3 (Hy-cube) project, which involves a unique hybrid production system utilising hydrogen and hydrogen-based renewable energy sources. This initiative aims to achieve carbon-neutral production and eventually specialise in producing premium carbon-neutral automotive parts. The project has originality in that it involves not only designing processes using electric furnaces to produce premium steel products such as car body panels and electrical steel sheets, but also aims to reduce carbon emissions from the process, developing carbon-neutral products based on market demand. To assess the feasibility of the Hy3 project, Hyundai Steel conducted two pilot productions. The first pilot was producing a prototype of lower-arm part using electric arc furnace with three different kinds of raw materials: molten iron, HBI (hot briquetted iron), and scrap. Successful performance evaluation of auto parts with 1 GPa strength was achieved. The second pilot has been focused on tire cord steel, with the first-phase tests yielding a 33 per cent reduction in carbon footprint (CFP). Using the advantages of operating experience in electric arc furnace, Hyundai Steel is preparing for test operations producing various automotive parts using an electric arc furnace (EAF) to advance the Hy3 concept. From a medium to long-term technological development perspective, Hyundai Steel’s blueprint includes producing high-end carbon-neutral steel products using hydrogen-reduced iron as raw material.

Jun 19, 2024

By Sandenbergh RF

The debate on the mechanism of adsorption of gold and silver di-cyanide onto activated carbon could be divided into two schools of thought. On the one hand, it has been proposed that the combined effects of electrostatic and chemical interaction between the activated carbon surface and adsorbing gold di-cyanide anion results in the adsorption of the latter. On the other hand the `ion-pair' adsorption reaction mechanism has been vigorously advocated as the dominant mechanism responsible for the adsorption of gold di-cyanide onto activated carbon. It is maintained that gold is adsorbed onto the carbon surface as the neutral ion-pair [M"+][Au(CN)z ]". Adsorption is viewed as the result of mainly the chemical interaction while electrostatic interactions are neglected. The validity of the `ion-pair' adsorption mechanism may be challenged on a number of counts. However, the alternative mechanism (based on aqueous surface chemistry principles) has not gained general acceptance yet, because it has not been applied widely enough to explain the different adsorption phenomena associated with gold di-cyanide on activated carbon. In the present study the case in favour of an adsorption mechanism based on general aqueous surface chemistry principles is presented. A model framework is developed for the adsorption reaction mechanism of gold di-cyanide onto activated carbon which incorporates the effects of chemical and electrostatic interactions between the dissolved species, the aqueous solution and the carbon surface. This model is then employed to explain a wide variety of reported adsorption phenomena for gold di-cyanide on activated carbon, such as the effects of pH, the adsorption of different metal cyano complexes, ionic strength, and type and concentration of cations in solution. In addition the effects of cyanide and dissolved oxygen concentration were investigated. No ready explanation, in terms of aqueous surface chemistry principles, is yet available for the switch in adsorption behaviour that agrees with ion exchange to ion-pair adsorption with increasing ionic strength.

Jan 1, 1997

By Zenari L, Kent D

As our mines introduce more sophisticated production technology into their operations, the dependence on communication systems is markedly increased to allow the management of the technology. However the attention given to the communication systems has lagged that given the production equipment - namely LHDs, trucks and jumbos. At times it was treated as after thought. However, this is changing as the degree of automation increases in our mines. The communication system is now being given much more priority and is genuinely becoming a part of the mine design. The transfer of information around underground, as well as between the surface and underground, is an essential day-to-day activity, with the aim being a smoothly run operation. However the mine environment is far from static, and situations arise - such as breakdowns or other incidents - that require swift analysis of the issue, its cause and its remedy. Also, as communication systems become more sophisticated their use in areas, other than direct data flow, become available. The importance of communication, its development, and new areas being impacted by communication is the subject of this Paper.

Jan 1, 1997

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006