Search Documents

By Alwan M

At Binebase mineralisation is hosted within an andesitic Neogene volcaniclastic succession on Sangihe Island, Indonesia. Two major alteration types occur; an initial widespread phyllic assemblage of quartz -illite with chlorite, smectite, gypsum and pyrite, and a superimposed quartz - barite - sulphide assemblage. The phyllic alteration arose from a neutral to weakly acidic hydrothermal solution of greater than 200 degrees C, and the quartz - barite - sulphide assemblage arose from a cooler slightly more acidic fluid. This second alteration event is interpreted to have selectively replaced permeable volcaniclastic breccias and coarse lithic tuffs within the altered sequence. Gold and silver mineralisation is associated with the latter alteration, and is locally controlled by the degree of silicification and sulphide abundance. The sulphides present are pyrite, covellite and chalcopyrite. The sulphides are very fine grained with colloform and framboidal textures and were deposited contemporaneously with the bulk silicification of the coarse sediments. A large portion of the mineralised rock has been oxidised to a quartz - barite -limonite - goethite - jarosite assemblage.Coincident gold, silver and antimony geochemical soil anomalies gave the best correlation with anomalous gold and silver grades in bedrock as identified by drilling. Resistivity proved a reliable geophysical method for delineating zones of silicification.

Jan 1, 1990

Magnetic separation using particle rotation in a continuously rotating magnetic field offers very low to insignificant non-magnetic particle entrapment, and precise magnetic fractions. The precision of rotating magnetic field separations makes the method ideal for dry laboratory magnetic analysis work, where conventional laboratory magnetic separators can give misleading or uncertain data. The very low entrapment characteristics make the method ideal for entrapment-critical separations within the diamond exploration industry or in gold recovery. A single wet rotating magnetic field (RMF) unit is able to achieve a cleaner separation (at similar or better recovery rates) than a three-stage separation using conventional wet drum separators. The RMF separator is able to work effectively at particle sizes below 50 ¦m, and RMF separation could, at least in theory, be used down to single domain particle sizes. Rotating magnetic field (RMF) separation is carried out by magnetically spinning the particles at frequencies up to 300 Hz. The particle rotation itself may be used to roll the particles out of the separator. At angular velocities of 100 Hz, magnetic flocs are unable to form, and any entrapped particles are energetically expelled. In an RMF separator, the outer drum can be stationary while the inner magnet rotor rotates, allowing, for example, the injection of cleaning water underneath the separating magnetics to help remove small suspended non-magnetic particles.

Jan 1, 2000

The Rock Mass Rating (RMR) and Rock Mass Strength (RMS) classification systems for jointed rock masses are briefly reviewed, with particular reference to their use in slope stability studies. A correlation is provided between the results obtained from the two classifications and an equation is presented tentatively defining the RMR value for long-term stable slope angles. The validity of the equation is discussed in general terms in the context of slope stability problems commonly encountered in Western Australian open pit gold mines.

Jan 1, 1992

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By Ostrea AM

Aqueous oxidation in an autoclave at ele- vated temperatures and oxygen partial pres- sures is applied to Philippine gold-bearing sulfide ores and concentrates which respond poorly to conventional cyanidation. The gold concentrates are recovered from ores and tail- ings material using the patented OMLI Process (the OMLI Process is able to upgrade tailings material analyzing 0.50 g/t Au to a concen- trate with a grade of 5 g/t Au or better). The results show that with aqueous pre- oxidation of the concentrates ahead of cyani- dation a four-fold increase in gold recovery is obtained compared with straight cyanida- tion. The observed differences in response to the pre-treatment step between various mate- rials are correlated with their mineralogical composition. The chemistry of aqueous oxida- tion is also presented.

Jan 1, 1986

By Gregory L. M, Phillips G. N

Although it has long been recognised that there is a diversity of minerals associated with Victorian gold deposits, the degree to which this mineralogy is systematic or haphazard has remained uncertain. Recent work by the authors and students under their supervision permits a sharp delineation of the boundaries between different mineralogical domains, and these are interpreted in terms of recent rapid advances in Victorian tectonics, and the regional framework of Victorian gold geology described in Phillips and Hughes (1996).

Jan 1, 1997

By Cotton P. L

Although the terms "pipe" and "tube" are normally considered synonymous, a distinction is often drawn, the former term being applied to the hot finished product and the latter to cold finished material. It is, considered that the title of this paper includes hot finished seamless, and continuous-weld pipe, cold drawn seamless tubing, and electrically welded tubing.The continuous-weld process will be reviewed first, passing to the various methods of seamless manufacturing, which, in addition to meeting the demand for hot finished seamless pipe, also supply the raw material for cold drawn tubing, the manufacture of which will then be described. Finally the electric resistance-weld process will be Considered, and the paper will conclude with a brief review of the processes described and trends in present-day manufacture.CONTINUOUS-WELD PIPEThe raw material for this process is delivered in the form of coiled, hot finished, strip steel, generally referred to as "skelp". The end of one coil is electrically buttwelded to that of'the next, so forming an unbroken strip. This continuous ribbon of 'steel is fed into a skelp heating furnace, and brought to the correct temperature for the forming and welding operations which follow. This temperature is usually about 1,350°C.The heated skelp issues from the furnace into 'a multistand mill, in which the first pair of rolls is designed to form the skelp into tubular shape, the edges being in close proximity to, but not touching each' other. These edges...

Jan 1, 1951

By Osborn G

The bulk flotation behaviour of an industrial rougher bank has been determined with a view to characterising the size iepend ent behaviour of the identifiable nineral groups present. A relatively simple flotation model, based on first order kinetics and the assumption of perfect mixers in series ias been used to provide a fit to the operation of the cells. The adequacy of the model is discussed in relation to the characteristics of the ore and the size iependancy of the parameters. It is shown that improved fits are possible if the model accounts explicitly for this size dependancy and demonstrated how the model may be of use in prediction of the grade recovery relationships for different operating conditions as an aid to plant optimisation.

Jan 1, 1986

By S Kost, R Nievergelt, F Cortes

In recent years, the use of steel fibre-reinforced concrete (SFRC) for segmental tunnel linings has become increasingly popular due to numerous advantages including durability, resistance to spalling, reduced cracking at corners and edges and significant cost-saving potential. One of the key parameters for measuring the performance of SFRC is the residual (post crack) flexural strength. A problem often faced in design and quality control of SFRC is the high variability of results obtained by standard beam test methods, with reported coefficients of variability (CoV) in the order of 25 per cent. The high test variability results in a relatively low permissible design strength relative to the average flexural strength of the material and commonly leads to non-conformances with respect to residual flexural strength during production testing.This paper presents the implementation of an alternative testing method using large round determinate panels (RDPs) for quality control testing of the SFRC used in the segmental lining of the City East Cable Tunnel (CECT) in Sydney. The alternative RDP test method was found to correlate well with standard beam tests and significantly reduce the variability of test results, minimising the risk of outlying residual flexural strength results, with zero non-compliant test results reported during the production period.This successful implementation of an alternative test for post-crack flexural strength with lower variability in results constitutes a relevant precedent to demonstrate the feasibility of this approach which contributes to the development of more cost-effective concrete mixes and minimises the risk for non-compliant results and the contractual disputes that commonly arise from these.CITATION:Cortes, F, Nievergelt, R and Kost, S, 2014. Development of a segmental lining specification for steel fibre reinforced concrete flexural strength testing using round panel tests, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 461–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

This paper details successful implementation of a revolutionary pit access system involving excavation of an 'in-the-wall' ramp at Three Mile Hill open pit operated by Gold Mines of Coolgardie, formerly Goldfan Limited, at Coolgardie, Western Australia. Three Mile Hill is a medium-size, open pit, gold operation typified by hard, competent, fresh rock conditions from near surface. The project involved construction of a haulage tunnel or decline access located in the wall of an open pit in place of a conventional pit access ramp. Works undertaken as discussed herein included excavation, support, ventilation, dewatering, services installation, commissioning and monitoring. Prior to implementation, the conventional hardrock pit slopes and designs were constrained by the presence of infrastructure and a main road to the North and by adjoining leases to the Southeast. The combination of these factors and economic considerations resulted in a decision to proceed with an innovative in-the-wall ramp access system that is believed to be the first of its type in Australia. Back-analysis indicates that implementation resulted in a cost saving of as much as A$3.6 million and increased mineable pit reserves. The paper deals with the successful implementation and operation of the in-the-wall ramp haulage as well as an economic evaluation that is aimed at drawing some general conclusions on favourable conditions for implementation in other mining scenarios.

Jan 1, 1996

An integrated mining equipment development organisation is typified by Deutsche Montsn Technologic of Essen, Germany. working on improvements in reliability, production and control in coal mines. Examples of recent mining advances are in mechanised roadheading, in different approaches to cutting technology, and in low height roof bolting.On the longwall face the mechanics of cutting are related to supplied energy as well as to dust make. In conveying both armoured face conveyors and conveyor belts are monitored. Roof support is not neglected and the continuous pumping of stowage slurries provides further options for longwall support. Surveying developments, particularly the gyro-theodolite, directional drilling. and shaft vehicle monitoring provide further examples of advances in control in coal mining activities.

Jan 1, 1991

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

The Lower Proterozoic metasediments of the Pine Creek Geosyncline form a chrono- stratigraphic sequence of mainly greenschist- and amphibolite-grade shallow-marine to supratidal pelites, psammites, carbonate rocks, and volcaniclastics which in places rests unconformably on Archaean basement. Granite and later dolerite intrude the sequence, and are associated with the major orogenic 1800-m.y. event which regionally metamorphosed the sediments. Most mineralisation is stratabound, and can be related at least partly to volcanic activity. Uranium mineralisation is mainly confined to particular carbonate-rich horizons near basement. Other metals are mainly in small hydrothermal deposits near intrusive granite. Specialist studies indicate that uranium was leached from its source rock, and probably carried as carbonate complexes in highly saline fluids at between 100 and 3500 C. Precipitation took place by redox reactions in breccia zones in carbonate rocks; these zones were formed by carbonate solution or diapiric movement of evaporites which preceded the carbonate. Extensive chloritisation in the ore zones suggests metasomatism by Fe- and Mg-rich fluids which may have evolved during dewatering of the evaporites. The main mineralising event took place after the 1800 m.y. metamorphism, and was probably

Jan 1, 1979

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

By Clift N

Lead concentrate from the Isa and Hilton lead-zinc concentrators of Mount lsa Mines Limited is smelted at Mount Isa to produce a lead-silver bullion. This bullion is cast into four tonne blocks and shipped to Britannia Refined Metals Co Ltd, NorthDeet, England and to plants in Asia for refining and marketing. The traditional treatment stages at Mount lsa are sintering, smelting, and drossing and casting, with some of the sinter plant feed being pre-treated through an Isasmelt plant.A commercial scale lsasmelt based lead smelter was commissioned in early 1991.

Jan 1, 1993

By Sagrabb T

In a company's quest for financing the development of a new mine, it will make calls on stockbroking houses and banks. The choice of the best-fit broker or banker is of great importance, and in the case of the miner, this is a house that has an intimate understanding of the mining industry, particularly one that has a solid staff complement of personnel with operating mine experience at a senior level. The most important document that the company will present to support its financing request will be the Feasibility Study. It cannot be too strongly emphasised that this document must be absolutely comprehensive and cover items including: (a) Geological review; (b) Resources and reserves; (c) Mineability; (d) Mining schedule; (e) Metallurgy; (f) Process plant description; (g) Infrastructure and services; (h) Management and operations; (i) Environmental and social impact; (j) Capital costs; (k) Operating costs; and (1) Financial analysis. The elements listed above represent major topics and require a great deal of expansion in the body of the document. Rothschild Australia Limited assists its client companies by supplying a detailed framework so that they will be in a position give the bank the information it needs to complete its technical `due diligence' study within a mutually agreed time. The client company will advance its position markedly if it uses well-known, reputable consultants to either complete or assist with the various aspects of the Feasibility Study. Such an approach will give the potential financier confidence that the company has taken a professional and unbiased attitude in determining the feasibility of the property in question. Most small- to medium-sized mining companies, both within Australia and overseas, will prefer, or will find it mandatory, to request a project funding package rather than opt for a corporate loan. This is because the company either does not want to tie all of its assets to the performance of one project, or that it is a one or two project company with no other substantial assets and is therefore unable to obtain a corporate loan. Upon receipt of the Feasibility Study, the bank will use the data supplied by the company in its cash flow analysis to build its own financial model. The purpose of this is to examine the timing of

Jan 1, 1994

By Amanatidis A

In this paper, the kinetics of iron precipitation as sodium jarosite from aqueous solution is investigated. The determination of the reaction mechanism is attempted based on the experimental data of iron removal as a function of time, without using the characteristics of the precipitate.Experiments at the temperature range from 50° to 95°C were carried out with initial conditions of iron concentration IQ g/L, sodium sulphate concentration 25.44 g/L, sulphuric acid concentration 3.68 g/L, pH = 1.5 and agitation rate 600 rpm. Temperature greatly and positively influences iron precipitation from the solution and this is accompanied by pH decrease. The activation energy was determined using the maximum values of the precipitation rate, which were evaluated by polynomial fitting of the sigmoidal shape experimental curves, and it was found to be 44.37 kcallmole. The determination of the rate-controll ing mechanism was based on some criteria used for the discrimination among the three probable mechanisms of precipitation (diffusion, mononuclear nucleation, polynuclear nucleation). These criteria utilise various funetions of the recovery 'a' of iron precipitated versus time, the most important of which are the chronomals. The results of the kinetic analysis procedure showed that the polynuclear nucleation growth mechanism controls the precipitation of iron as sodium jarosite. This was confirmed by the high value of activation energy, excluding diffusion as the controlling mechanism.

Jan 1, 1993

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M Kuruppu

The paper explores the sustainability of the Australian mining industry, and the potential for application of a substitute fuel into existing mining operations. This alternative fuel biodiesel is produced from biological oils and not from refined hydrocarbons like the transport fuel diesel (petrodiesel). The fuel is compatible with all current diesel equipment with little to no modification and has many superior properties. As biodiesel is derived from biological sources it is æcarbon neutralÆ meaning there is no net carbon addition to the atmosphere when the fuel is burned. The current fuel, petrodiesel releases long stored carbon dioxide (CO2) and is of concern to Australian government targets which seek to reduce these emissions. The mining industryÆs unique reliance on petrodiesel is of particular interest when assessing the substitution of biodiesel into underground and open cut operations. The underground benefits of biodiesel see a reduction in the noxious emissions of carbon monoxide and diesel particulate matter, both contaminants which require extensive diluting ventilation to ensure safe levels. As biodiesel is both safer to store due to its higher flash point and produces less exhaust emissions, its occupational health and safety benefits in underground mines is clear. The use of biodiesel in open cut mines benefits the environmental sustainability aspects of the project. The formulation of national targets relating to carbon dioxide emission reductions promotes any measure to reduce CO2 within the mining environment. As the diesel engine is one of the least emission efficient (kWh/tonne CO2) energy sources on-site, its potential for reduction in CO2 at minimal cost is the greatest. By substituting the fuel, significant quantities of site emissions are reduced, thereby achieving the goals of improved site sustainability and the governmentÆs targets to reduce emissions. This aspect of gauging mutually beneficial relationship regarding government interests and mining industry profitability is the underlying outcome for this paper.

Jan 1, 2009

The Northwest Territories (NWT) of Canada has emerged as a major new province for diamond mineralisation in less than three years. This is primarily the product of a diligent search in the form of a scientifically based exploration effort. However other factors, including positive aspects of the business and the legal environment have also been identified as assisting the exploration process. In my view these have increased the likelihood of diamond mining becoming a major new industry for Canada. The supportive role of various government agencies has been important. In addition, the character of many of the joint venture deals that have been done has provided an attractive setting for the capital intensive evaluation and development work that is now required to bring the diamond discoveries into production. Perhaps of equal importance is that with the recognition that is being given to the success of the NWT diamond ventures, Canadian explorers are continuing to attract new risk capital for further exploration. This paper attempts to model and quantify the probability of exploration success translating into successful mine development.

Jan 1, 1994