Search Documents

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Lungfish and crayfish inhabit continental ecosystems similar to those of their ancient counterparts in the Permian (lungfish) and Triassic (crayfish) Periods, exhibiting similar burrowing behaviors to live, breed, and escape desiccation. Identification of their burrows in the geologic record when body fossils are absent has relied on the overall gross morphology of the burrows and the process of elimination. A method of burrow identification has been developed by evaluating burrow structures in an attempt to designate architectural and surficial burrow morphologies that uniquely reflect the distinctive burrowing mechanism of a particular organism. The information from this method defines the burrowing signatures of an organism, enabling the differentiation of their burrows even when fossil evidence is lacking.The lungfish constructed simple, vertical burrows with bulbous terminations. The burrow walls exhibit fine, horizontal to sub-horizontal striae and vertical to sub-vertical striae near the top of the bulbous terminus, reflecting a burrowing style similar to modern burrowing lungfish. The crayfish constructed simple, vertical burrows to complex burrows with multiple branching and chamber development. The burrow surface ornamentations exhibit horizontal to sub-horizontal ridges, vertical to sub-vertical groupings of scratches, mud- and lag-liners, knobby and hummocky textures, and body impressions, which reflect the burrowing mechanism of the crayfish.

Jan 1, 1990

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

By E Gabriel, J C. Koppe, A Gomes and P Crispim, R Schaarsdmit, I Pablos

Drill and blast (D&B) is one of the most important production operations in open pit mining. The resulting fragmentation of the D&B reflects in the downstream unit operation. Good fragmentation of the ore will minimise the cost of loading, hauling and crushing. The understanding of the geological model integrated with a software system for bench face surveying and planning of blast layouts based on three-dimensional images can help to achieve the fragmentation goals of the mine operation. A case study integrating these tools was carried out in a large iron mine in Brazil. The iron ore in the study area consists of hard and friable itabirites. More than three different ore types may occur on the same bench. Under these conditions, data integration becomes necessary to improve the results of blasting. A blasting plan was based on the generated geological model. The methodology helps understanding the factors that can interfere in the fragmentation process, allowing defining actions that can improve the blast design in those places that fragmentation wasn’t achieved. This condition is important for a continuous improvement of the drilling and blasting operation. In comparison with the previous blasting carried out at Itabira mine, which did not take into account the geological model, substantial improvements in fragmentation were observed, eliminating the need for secondary blasting.CITATION:Schaarsdmit, R, Pablos, I, Koppe, J C, Gabriel, E, Gomes, A and Crispim, P, 2015. Geological modelling and bench face survey to improve blasting fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 401–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Gagnon, P Bouchard, F Vanier, E Soares de Lima Filho, J El-Haddad, M Sabsabi, G J. Wilkie, A Beauchesne, A Hamel, A Blouin, T Vaillancourt, F Boismenu, A Harhira, A Plugatyr, C Padioleau

Quantitative mineralogy is an established discipline in the geosciences and is aimed at providing mineral grade and texture information for geological and mineral processing applications. The two core technologies underpinning Quantitative Mineralogical Analysis (QMA) are Scanning Electron Microscopy (SEM) in combination with Energy-dispersive X-ray Spectroscopy (EDS). Technologies such as QEMSCAN and MLA are now routinely used to optimise the performance of large-scale mineral processing plants in the base and precious metal sectors. One of the major disadvantages of the QMA methods used today is extensive sample preparation requirements which make application of this technique to real-time mineralogical characterization not feasible. A breakthrough has been achieved by the National Research Council Canada in collaboration with CRC ORE by developing a novel Laser Induced Breakdown Spectroscopy (LIBS) based technology capable of real-time mineralogical characterization of process streams without sample preparation. The potential applications of this technology include, but not limited to, in-pit muck piles, underground draw points, cross-belt analysis as well as slurries. This paper describes the development of the LIBS-based technology from a proof-of-concept (TRL2) to the construction of a prototype sensor and its validation in a simulated environment (TRL5). Future work is being planned to test and further validate the LIBS sensor on a mine-site which will progress the technology to its next readiness level (TRL6).

Nov 10, 2020

By L Sandery, S Light

Within 22 months of commencing decline development, the Prominent Hill Ankata Underground Project achieved its full production rate of 1.2 Mt/a.In 2010 construction of the Ankata Underground Project was approved. Decline development commenced in November 2010 and the turnout for the first sublevel was reached by August 2011. The first stoping ore was produced in the first quarter of 2012 and production was successfully ramped up to full production during the third quarter of 2012.Diamond drilling commenced in October 2011 and was conducted concurrently with the underground development. This presented challenges as mining and production targets had to be balanced with underground exploration activities. To achieve production on schedule, without adversely affecting the diamond drilling program and future development, meticulous and adaptive planning techniques were required. This included involvement from engineers, geologists, underground operators and underground diamond drillers.The granularity of these planning techniques allowed the management and prioritisation of development and diamond drilling down to an almost hourly basis. A constant flow of information from drill assay results was fed back into the planning systems. This resulted in a constantly evolving mine plan as the orebody was further refined. High priority areas were identified and targeted to allow continued development and a successful rapid ramp up to full production.CITATION:Sandery, L and Light, S, 2014. Managing the diamond drilling interactions in commissioning the Ankata underground mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 75–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

In May 2000, Kanowna Belle Gold Mines (KBGM) carried out a detailed Truck versus Shaft Haulage Study. The study showed that whilst the shaft option had many operating cost benefits the capital costs were too high, therefore the truck option was selected. In May 2001, the concept of achieving æshaft typeÆ benefits without the capital costs was floated. This is achieved by separating the hoisting of ore from other mining activities. The general concept is that material from underground is transported to a central location and then transported to the surface by a special truck fleet, thus removing the dependency between trucks and loaders, providing the mine with surge capacity and decreasing operating costs. At KBGM these advantages have been gained by installing an ore pass system with a plate feeder at its base that directly loads trucks. This provides the mine with a haulage system with enough surge capacity to remove the interdependency between trucks and loaders. The plate feeder is situated just off the decline which creates the opportunity to use larger more reliable, lower cost trucks. A number of truck types were considered for the truck loop including Elphinstone AD55Æs which are the truck type being used on site prior to the truck loop, CAT 775EÆs and power trailer road trains. This paper covers the philosophy behind the truck loop, the truck selection process, project installation and commissioning, people issues and the benefits expected by the operation. As of May 2002, the project is nearing completion, with decline haulage expected to commence in July 2002.

Jan 1, 2002

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

The problems encountered with the introduction and use of Isanol underground are described. Significant direct as well as indirect savings have resulted from the use of Isanol. Field studies have shown that the concentration of common gases released during detonation is considerably lower than with conventional nitro-compound type of explosives.

Jan 1, 1977

By G Pasin, F Wirfiyata, G Khomaeni, W Valery, A Maclean, A Jankovic

The grinding circuit at PT Newmont Nusa Tenggara (PTNNT) – Batu Hijau mine consists of two SABC (semi-autogenous milling, ball milling, pebble crushing) trains, including four 20'?×?33'6? ball mills that have been lined with steel liners since the commissioning of the plant in 1999. During 2011 and 2012 an industrial trial was conducted to evaluate Poly-Met liners (a combination of rubber and steel liners). These new liners were installed in two of the ball mills (ball mills 1 and 2) and operated in parallel with ball mills 3 and 4 with steel liners.The objective of the trial was to compare the plant performance with the Poly-Met and steel ball?mill liners with regards to wear life, mill throughput, grind size and total unit costs. The trial was conducted over the entire life of the liners. The evaluation methodology implemented consisted of frequent spot sampling around the ball mill circuits, complete surveys/audits in both ball mills, and detailed analysis of process data. This paper presents the results of the industrial trial and main conclusions.CITATION:Maclean, A, Wirfiyata, F, Khomaeni, G, Jankovic, A, Pasin, G and Valery, W, 2014. Ball mill Poly-Met liner evaluation at PT Newmont Nusa Tenggara – Batu Hijau mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Research cruises dedicated to seafloor hydrothermal activity along the Kermadec arc first began with the Sonne-135 expedition in 1998. This was followed by the worldÆs first systematic survey for venting along an arc during the 1999 NZAPLUME I expedition. Since then, cruises dedicated to mapping plumes along the Kermadec arc include NZAPLUME II (2002), NZAPLUME III (2004) and ROVARK (2007). In addition, the manned submersible cruises SWEEP Vents (2004) and NZASRoF (2005) utilised the Shinaki 6500 and Pisces V, respectively, to sample in detail select hydrothermalsystems for mineralised samples, rocks and vent fluids. The ROVARK (2007) cruise was the first to deploy an autonomous underwater vehicle (ABE) along the arc which surveyed Brothers volcano at a far greater resolution than had been done previously by ships on the sea surface. While these expeditions have largely been led by GNS Science, together with its collaborators from National Oceanic and Atmospheric Administration, Pacific Marine Environmental Laboratory (NOAA/PMEL), significant contributions have been made by other groups from various nations, exemplifying the global interest in seafloor hydrothermal activity associated with intraoceanic arcs. This is an ASTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J S. Laskowski

Froth flotation process requires the use of frothers. These important flotation agents are commonly characterised as either æselectiveÆ or æpowerfulÆ and are chosen following general guidelines and verification by laboratory and/or pilot plant tests. Fundamental properties of the flotation frothers have been extensively studied over the last few years. These studies have led to the development of standardised procedures to characterise frothers in terms of their ability to reduce bubble size and to increase foam stability. In this research project, the performance of five frothers in flotation of coal is evaluated and related to the fundamental properties of these agents. Since the recovery of water in the concentrate is closely related to the non-selective transport of solid particles by entrainment, the tested frothers are also assessed in terms of their ability to promote the transport of water towards the froth collection zone, both in absence and in presence of solids.

Jan 1, 2005

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990

By N Kojola, A Vickerfält, J Huss

The possibility of using an acidic autogenous hydrogen direct reduced iron (H-DRI) slag as a basis for vanadium extraction is investigated. For a raw material to be suitable for producing high-quality FeV, the vanadium oxide content should be sufficiently high and the phosphorus oxide content in a tolerable range. Therefore, the feasibility for vanadium extraction relies on fulfilling two demands: the predominate partitioning of phosphorus to the metal and vanadium to the slag. Correspondingly, the behaviours of phosphorus and vanadium in the Al2O3-SiO2-FeOx-VyOz-P2O5-Fe system were studied experimentally. Slag, 10 g, was put in contact with liquid iron, 30 g, for different durations (2–24 hrs) in closed alumina crucibles at 1873 K. The slag composition was varied between 33.1– 49.3 wt per cent Al2O3, 27.1–46.7 wt per cent SiO2, 16.6–30.1 wt per cent FeOx, and 2.5– 8.8 wt per cent V2O3. The equilibrium phosphorus distribution was 0.42, while the vanadium distribution ranged from 7.6 to 43.4, increasing with the Al2O3- and the FeOx-content.

Jun 19, 2024

By S Benson

Staurolite is one of the major contaminant minerals contained in the Tiwest Cooljarloo orebodies. Approximately 80 per cent of staurolite in mined ore, reports to the heavy mineral concentrate that is supplied to the Dry Mill. Staurolite in heavy mineral concentrate is typically five per cent by weight and has no significant effect in the Dry Mill other than to occupy equipment space, reporting as a tailing, that requires transportation and disposal back to the mine site. Staurolite is an aluminosilicate with a MohÆs hardness of 7.5. It is known to have potential as an abrasive blast agent and it is produced in substantial quantities in the USA for that purpose. Research indicated that there was potentially a market for staurolite within Australia, as a replacement for some of the lower grade abrasives as well as a material of choice. A small tonnage of staurolite product was manufactured through a simple circuit within the Dry Mill in December 1998. This was subjected to industrial scale tests by external companies specialising in sand blasting. The most significant batch of tests were conducted at the Tiwest Chandala site on plant and equipment undergoing corrosion repairs. Staurolite was tested against three other commercially available abrasives and compared very well with respect to surface profile, surface texture, coating adhesive strength and dust generation. As part of a due diligence study, free silica, radiation and heavy metals contents of spent abrasive and dust was investigated. This information was needed to seek approval from the appropriate Western Australian statutory authorities to sell staurolite as a product. Approval was received in November 1999. Tiwest has since installed a production circuit in the Dry Mill capable of producing 20 000 tpa of Staurolite.

Jan 1, 2001

By Billingham R

The Department of Mines Tasmania employs a Drilling Section for specialised drilling re- quired by government and semi-government bodies. The section has a complement of nine crews oper- ating auger, cable tool, rotary and diamond drilling plants. For some years the Department has been involved in site investigation drilling of the Derwent River. The experience gained indicated that drilling methods should be altered. In 1976 an urgent programme was requested and the opportunity was taken to solve many problems associated with previous investigations. Equipment and methods are discussed in detail. The improved technique contributed to the suc- cessful completion of the Phase 1 site investi- Gation.

Jan 1, 1977