Search Documents

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By Pratt V

The economic, social and political environment of the mining and minerals industries is, as we all know, volatile and affected by constantly changing international forces. In addition, the outcome of negotiations with overseas customers is often uncertain for long periods, or even unfavourable. The industries and companies represented at this Conference are in an arena of high competition, risk taking and enormous capital outlay. They are industries which our overseas markets (rightly or wrongly) have criticised for industrial relations problems, unreliable production and uncertain deliveries. They are industries which have an urgent need to be cost effective and competitive at all levels of activity.A critical factor in the mining and metallurgy industries is, therefore, its human resources and its human resource management. It requires the full use of available talent, innovation, skills and qualifications within its workforce, and the appropriate management of these resources.

Jan 1, 1985

By Jephcott S

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists of a mineralized bituminous shale sequence containing some tuffites, numerous graded beds and isolated slump breccia horizons. The principal sulphides; pyrite, sphalerite and galena, are essentially restricted to the shales and the genetically unrelated turbidites contain only minor mineralization. The geochemistry of the deposit has been investigated with respect to the stratigraphio column and mineralogy of the sediments.

Jan 1, 1980

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By G Caddy, M Middleton, S Kerec, R Keil, J Tsalapatis

Arrium’s OneSteel Whyalla Steelworks in South Australia is a fully integrated plant which operates a single blast furnace. The key operational objective has been to maintain high process availability and stability while maximising the process efficiency and the produced hot metal quality. All ferrous raw material input feeds are sourced exclusively from company iron ore deposits in the nearby Middleback Ranges. The Whyalla blast furnace has mostly operated using a combination of a high percentage of pellet feed, produced in Whyalla, together with screened lump ore.The unique ironmaking challenge has always been to extract the maximum value from the ferrous burden feed available locally. In earlier times, high-grade hematite lump ore was available for both screened lump ore and pellet production. Blast furnace trials from acid to fluxed pellet feed commenced in 1977. The furnace pellet feed has been wholly fluxed since 1981. Many pellet/lump ore feed mixes and significant pellet chemistry composition design changes have been made over the years. These changes have been aimed at best balancing the ferrous burden availability/cost and the optimum reducibility/high temperature melting behaviour of the charged ferrous feed within the blast furnace. In more recent times since 2007, the Whyalla blast furnace operation has transitioned from a hematite based pellet feed to a magnetite based pellet feed while there is an ongoing contest dealing with diminishing absolute quality/increased variability raw material feed inputs.The paper will detail key elements of the Whyalla blast furnace operational philosophy with regards to ferrous feed use and process optimisation. The blast furnace ferrous feed design considerations will be discussed, together with the test work performed, the operational and slag design transition strategies employed and the process results achieved.CITATION:Tsalapatis, J, Middleton, M, Keil, R, Kerec, S and Caddy, G, 2015. The use and optimisation of ferrous feed at the Whyalla Blast Furnace, in Proceedings Iron Ore 2015, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Caron, M Athayde, F Lavoie, R Joyce

Decarbonisation has become a major challenge for the global steelmaking industry, turning towards new technologies aimed at carbon footprint reduction, which on its own accounts for approximately 9 per cent global emissions. The iron and steel industry represents a ‘hard to abate’ sector, where much of efforts are currently being deployed into initiatives aiming to decarbonise the ironmaking through the use of green hydrogen, carbon capture utilisation and storage and state-of-the-art operation of current technologies, while little efforts being deployed to find carbon-efficient solution to iron ore burden preparation, where high-grade iron concentrate will increase in importance to ironmaking regardless of the chosen reduction route. Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), produces high-grade hematite concentrate with one of the lowest carbon global footprints. Still, QIO is partnering with its clients to the development of burden solutions to minimise CO2 emission, in the seek for a decarbonised steel. In a strong technological partnership, Binding Solutions Limited (BSL) has developed a novel, coldbinding technology to provide a cleaner, more cost-effective alternative to induration. The technology allows miners and steel producers to reduce Capex significantly and reduce energy consumption and CO2 emissions by 90 per cent. QIO and BSL have partnered to adapt the disruptive cold binding technology developed by BSL to QIO’s concentrate to produce a high-quality low emissions iron ore agglomerate. This paper describes the efforts taken to further develop BSL’s cold binding technology and its application to QIO’s high-grade iron ore concentrate to produce a hematite cold bonded briquette (hCBB) showing comparable performances with high quality seaborne fired pellets.

Nov 8, 2021

By Low Russell

Mark Westfield, writing in The Australian on 16 May 1994 stated: The role of the independent expert is crucial to Australia's investment system. When it falls down, there can be very dramatic consequences. The scope of these consequences was dramatically illustrated in the decision of Rogers J. at first instance in Cambridge Credit Corporation v. Hutcheson (1983) 8 ACLR 123 when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million, well in excess of their insurance cover. No comfort should be sought in the fact that this decision was overturned on appeal, for the result of the appeal rested on whether there had been a causal connection between the breach of contract which had occurred and the loss suffered, rather than on the fundamental principle of auditors' liability. Thus: Those who prepare experts' reports in company cases carry a heavy moral responsibility, whatever their legal duties may be... Unless high standards are observed by those who prepare these reports, there is a danger that systems established for the protection of the investing public will, in fact, operate to their detriment through reliance placed on those reports and on the reputations of those who furnish them. In lending his name, the expert will often, as in this case, be lending a name to conjure With.

Jan 1, 1995

By T Niitti, J Turunen, P B, A Rinne

In todayÆs marketplace, with high metals prices, many operations are faced with the challenge of improving recovery in the particle size ranges which are normally difficult to recover. This presentation focuses on the various methods used to alter the flow dynamics in a mechanical flotation cell, thereby improving metallurgical results. Modern computational fluid dynamics (CFD) tools have been used in the design phase, with subsequent validation at the plant. Some of the validated variables include mixing profile, power draw and local air hold-up. This presentation underlines how modern CFD analysis can be used to screen and select different approaches before commencing costly trial-and-error experiments at plant scale. Two methods of affecting flow dynamics are discussed û firstly, by altering the geometry of the rotor-stator area and, secondly, by fitting additional features in the tank. The rotor-stator area can be modified to provide more concentrated turbulent kinetic energy or, respectively, to provide more pumping efficiency with less attrition. The tank can be fitted with various additional features, aimed to create different particle suspension profiles. The benefit of both methods is that they can be applied not only to newly installed flotation technology, but also to existing plant cells, thus enabling potential improvement in the mixing profiles, solids suspension, tank sanding and metallurgical performance. Results of several sitesÆ tests are discussed in terms of flow variables measurement as well as metallurgy. This paper demonstrates the effects of different flow dynamics on the mixing profiles and metallurgical results of existing mechanical flotation cells.

Jan 1, 2006

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

By Y G. Anoman

This paper discusses the operating model within Endeavour Mining Corporation regarding the options of owner mining against contract mining. It’s based on the concept of ‘are we carrying out the most efficient mining’ regarding cost and performance. This question can only be answered through an extensive contract mining tender process and conducting a comprehensive comparison to evaluate the transition viability. Karma mine, located in Burkina Faso, is the subject of this paper. The Tender model included sales of equipment, parts and tooling associated with the traditional Load and Haul Schedule of Rates (SOR). The methodology focused on the structure of the tender process, which consists in the development of a SOR based on haulage profiles and mining schedule. This is a new Endeavour framework that allowed the bidders to compete on an even level. This was performed using a systemic analysis which encompassed all the elements involved in a transition such as the Human Resources (HR), taxes and customs implications, directs and non-direct costs (Finance and interest on assets, depreciation, insurance), contractor risk profiling. It was assessed against the normalised internal pricing tender-based. This paper gives an insight into how a West African mining operation addressed the sensitivities of the HR functions against the commercial aspects. This was one of the most successful transitions in West Africa and was carried out during the COVID crisis. The outcome of this project has created value by detailing a lesson learned model for both commercial and HR aspects. This discusses the commercial comparisons along with the internal model with the underlying HR functions as a risk factor that could have jeopardised the continuation of the operation. This resulted in a smooth transition with the additional cash flow generated by the sale of the parts and equipment turned Karma into a viable operation.

Jun 22, 2022

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By S Bluhm, L van den Berg

In planning mine ventilation systems, heat issues are normally associated with deep-level mines where auto-compression and virgin rock temperatures play a major role. However, a number of mines suffer from high ambient temperatures and humidity, very steep virgin rock temperature gradients and an influx of hot groundwater. Mines in Australia and, particularly, South-East Asia have to deal with these environmental conditions, both in the operational and planning phases. These operations normally have to take heat into consideration during the planning stages at much shallower depths. In high rainfall regions, the water table is saturated and groundwater flow rates are particularly high, which add significant water heat load potential to the mine ventilation system.This paper considers the ventilation challenges associated with hot groundwater conditions in mechanised mines. The paper is based on specific project experience gained from a number of projects in the United States, Australia and South-East Asia and draws on data from mines that experience hot groundwater conditions. For one site, actual decline temperature survey measurements, modelling techniques, management strategies and design considerations are presented.CITATION:Van den Berg, L and Bluhm, S, 2015. Ventilation planning considerations when dealing with hot groundwater, in Proceedings The Australian Mine Ventilation Conference, pp 211–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By P Thompson, D Rose, S Yu, W Baum, R Zahn, D Meadows, G Hall

Opportunities to improve mill operations are often cited by mining companies and recognised in many concentrators spread throughout the world but are not always followed through. Copper-molybdenum concentrator operations are challenged by a continuously increasing list of detrimental factors. They include deteriorating ore characteristics and poor mineralogical information on deeper ores, water quality and availability, steel wear and increasing power costs. Rapidly declining productivity, sustainability and environmental factors, new taxes, mining industry global skill set shortages, to name but a few, must also be considered. The days of maximising value by just increasing production or simple cost cutting are fading and will not be sufficient for the future of more complex mineral processing operations and larger plants. As a result, FLSmidth’s Global Process Technology Group has launched a plant and process optimisation program based on mineralogical and metallurgical surveys.Copper-molybdenum concentrators of the future need a paradigm shift. Modelling and simulation tools alone are not the answer to complex mineralogical associations and larger scale equipment and operations. Detailed area by area review aimed at identifying process constraints in terms of equipment and operating practice in conjunction with robust diagnostic work, ie mineralogical and metallurgical characterisation, are mandatory for process optimisation. The navigational beacon, for all operations who want to remain competitive, will be ‘process efficiency’. Since the use of automated mineral analysers has become more readily available and reliable, mineralogical-metallurgical plant surveys have proven themselves as the most efficient tool for optimising plant performance.The following paper will illustrate how operations can move toward eliminating under-performing flow sheets, fixing run-away flotation conditions, maximising individual process equipment performance, preventing shortcuts in Bond work index testing which may cause the failure of comminution models and minimising costly and time-consuming ‘debottlenecking’. As previous plant surveys have shown, the net project cash flow can be increased by 50 to 200 per cent if a combination of robust ore characterisation and plant process mineralogy is performed. The combined plant survey approach has been demonstrated successfully in a multitude of operations. This includes the use of key ore types in concert with statistically sampled process streams, bench-scale metallurgical tests and automated mineral analysis on a size-by-size basis.CITATION:Meadows, D, Hall, G, Rose, D, Thompson, P, Baum, W, Zahn, R and Yu, S, 2014. Copper-molybdenum concentrator surveys using mineralogy and process benchmarking tools to improve overall plant performance, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Gomez-Hernandez, P D. Munro

Filtered dry stack tailing storage facilities offer many advantages over thickened tailing storage facilities and yet, most of the mining companies still prefer the latter.Some of the advantages of filtered dry stack tailing storage facilities are: increased structural integrity of the tailing storage facility, which is even more critical in areas of high seismicity, close to nearby communities or environmentally sensitive areas; maximised water recovery which is particularly important in arid environments where water is an extremely valuable resource and its supply is regulated; optimised recovery of valuable metals in the process water, avoiding high cyanide concentration going to detoxification (both aspects haven’t been emphasised enough in technical papers on this subject); optimised space to store the tailings in mountainous regions; minimised elevation of embankment height, providing a safe option to store the tailings in places where there is limited area available; simplified license approval to operate where the tailing facility is a big issue; and avoidance of potential problems with nearby communities.Filtered dry stack tailing storage facilities have some disadvantages such as: technology limitations in operations that process high throughputs (eg >50 000 tpd) as they require many filters resulting in high maintenance and operating costs; higher capital cost; low efficiency in the filtration process, particularly in ores with high clay content increasing operating problems and capital cost; the new technology risk with possible debottlenecking issues and a longer time to achieve the design throughput; and the need to treat larger water flow rates when the water balance is negative.This paper analyses: the operating practices of Mexican gold and silver operations using filtered dry stacking storage facilities; implementation issues, advantages and disadvantages; quantifiable reductions in gold and silver losses and actual lower detoxification cost; and current trends to use filtered dry stacking storage facilities in new projects. The data gathered raises questions about (a) the need to collect data on tailings filterability, and; (b) reducing the current high operating cost of tailings filtration.CITATION:Espinosa-Gomez, R, Gomez-Hernandez, S and Munro, P D, 2018. Tailing filtration practices in Mexican gold and silver mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 275–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T Kojovic, S J. Windle, J Sullivan

"The Geometallurgical Mapping and Mine Modelling (GeM) comminution index (CI) was developed as part of the AMIRA P843 GeMIII project. Drill core geochemistry samples were passed through a Boyd Crusher with standardised settings and the resulting particle size distribution (PSD) was measured using sieves.Disadvantages of the original measurement were the relatively coarse crush size, requiring a second pass of crushing for geochemical sample preparation, and the limitation of throughput caused by the sieving step. At Antamina, the measurement has been modified to use a 2.2 mm crusher size setting, which permits a single pass. The PSD is measured using a Camsizer, an automated optical sizing instrument. The Camsizer sample is a +180 µm fraction, used to avoid passing too many fines through the instrument and slowing down the measurement. In the sieving step, the weights of the two fractions are recorded and subsequently used to normalise the distribution measured by the Camsizer. In this way, the throughput of the Camsizer can match that of the Boyd Crusher. The PSD data are therefore measured without penalising the throughput of the sample laboratory.The normalised PSD distributions are used to derive modified CI parameters, based on the slope and intercept of the breakage product size distribution, which are indirect measures of the material breakage hardness.Fifty samples were selected as a training set, each sample a composite of five or six individual assay intervals and each with its own measured CI. The average PSDs were calculated for the composites and used to calculate a composite CI. The intact half of the core, approximately 40 kg, was tested to measure the BWi, A*b and crushability. The results were used to develop predictive algorithms for these hardness parameters.A further 50 composites were chosen for lab testing, to serve as a blind test of the algorithms. The paper reports on the test results and the incorporation of the modified CI data and predicted hardness parameters into the Antamina block model.CITATION:Windle, S J, Kojovic, T and Sullivan, J, 2016. Use of a Modified Comminution Index to Predict Bond Work Index and SMC A*b at the Antamina Mine, Peru, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By H Zhang, A Lawrence

To accommodate the fast growing need for services in Singapore’s Marina Bay downtown area, Marina South, the construction of a common services tunnel (CST) was required. The CST includes various services such as telecom cables, power lines and water pipes. A deep excavation and temporary earth retaining system (TERS) was required to facilitate the construction of the tunnels. Marina Bay is reclaimed land over thick soft marine clay which is likely to be still consolidating. The deep soft marine clay poses a big challenge for deep excavations in downtown areas where highways and sensitive structures are close by. This paper presents a case study of part of the CST Phase 1B and 2 at Marina South, in particular a 26 m deep excavation supported by a 46 m diameter temporary caisson. The construction started in late 2006 and the basic structure was completed in early 2011. The caisson was formed by 1.0 m thick overlapping diaphragm wall panels with a capping beam and three ring beams at different depths. Two-dimensional finite element analyses were conducted to predict the ground settlement, lateral displacement, bending moment and hoop stresses in the diaphragm wall and ring beams during different excavation stages. A comprehensive instrumentation and monitoring scheme was established to verify the design predictions, control excavation safety and trigger the contingency plan to protect public safety. The impact of construction activity, unbalanced temporary stockpiles and adjacent deep excavation for a mole removal will be discussed.CITATION:Zhang, H and Lawrence, A, 2014. A case history of a deep excavation in a big circular shaft in Singapore marine clay, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 581–588 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014