Search Documents

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand there has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of -200 mesh material in the final product markedly increases costs of dewatering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins.

Jan 2, 1958

By W. P. Lass

The gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co., Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About 3 or 4 tons of this precipitate is produced monthly having 'a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the byproducts from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 1b. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high. The upper electrodes, of graphite or carbon, are 3 in. in diameter and 40 in. long, arranged with joints enabling new electrodes to be connected without shutting down or wasting stubs. A screw feed was arranged for raising and lowering the upper electrode. (Figs. 1 and 2.) The cover for the furnace had three openings, one for feeding the charge, one for the escape of gases, and one in the center for the introduction of the electrode. It was later found more practical to enlarge this center opening to 6 in. in diameter, to allow of a central feeding of the charge around the electrode.

Jan 1, 1916

By Shiou-Chuan Sun

THERE are several postulations for the mechanism of slime-coating. Ince1 proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube, after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4: 1 and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,4 several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.[4a] per liter of water, should not be

Jan 1, 1943

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

By John V. Beall

Tsumeb has added a chapter to its absorbing history with the beginning of copper smelting operations this month. This development will be followed shortly by another one when lead smelting and refining plants go on the line next year. In our own milieu these events would be common- place enough (although a new lead smelter certainly would be cause for wonder), but in the sparsely settled remote regions of northern South West Africa they are a dramatic industrial expansion. They are also, however, a sound businesslike extension of policies which have marked the tenure of Tsumeb Corp. Ltd. The historical data given in Table I are a drab listing of factual bones without the corporeal splendor which should surround the denouement of the Tsumeb bonanza. When Sir Francis Galton traversed the country, his was an expedition which was in keeping with the then blooming era of heroic explorations. The Otavi highlands in the interior were unexplored and the reception of the natives uncertain. While the exploratory work was in progress during the turn of the century the Hottentots and Hereros were successively in open bloody rebellion. The suppression of these uprisings, particularly the Hereros, by German soldiers so decimated the tribes that a labor shortage ensued for many years, hampering the development of the colony. To these troubles may be added difficulties In obtaining mining supplies. However, there should have been no shortage of meat from wild game judging by conditions prevailing even today.

Jan 12, 1962

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By Alfred E. Hunt, Geo. H. Clapp

The great advantage to he gained by a careful inspection of all materials used in construction, in regard to safety and permanency, and to accuracy of workmanship, has been longer recognized in Great Britain and on the Continent than in America. This is probably owing to the way in which great enterprises have been " rushed" in the United States. Time and cheap first cost, in too many instances, have been considered of more importance than absolute safety and durability; the structures being afterwards strengthened if this was found necessary. This has been most noticeable in railroads built through " new " country, where the object in view has been to reach the terminal point and get to work. These " loose " methods are now being very largely done away with, and a large proportion of the structures lately built are not only carefully inspected during the process of

Jan 1, 1891

By Eugene Guccione

For at least a decade, the energy crisis was accurately predicted by a small number of industry people who were ignored until last year, when they suddenly found themselves accused for their "lack of planning" and "greed." With the worsening shortage of natural gas and oil, the current scramble is for alternate energy sources-which means: a big rush into coal and uranium mining. (Some big plans are also on the drawing boards regarding geothermal steam, oil shale, tar sands, and even solar energy. But developing such new industries from scratch would be difficult enough even in a healthy economic climate-which is not exactly what the country currently enjoys.)

Jan 8, 1974

By R. L. Bleifuss

The object of this study was to evaluate the oxidized taconites of the western Mesabi iron range and to establish a correlation between the various basic taconite types and their concentratability. The initial work included a study of the original mineralogical and stratigraphic facies of the fresh taconite and traced the oxidation and leaching patterns developed during the conversion of this material to oxidized taconite. Subsequent studies have extended this work to include the semitaconites and also the wash and heavy media ore types widely developed in the area. Each basic original mineralogical facies or taconite type produces during alteration an equivalent secondary oxidized facies which has a unique mineralogical composition and texture. These control the concentratability of the oxidized taconites. Actually the influence of the original mineralogical composition of the iron formation extends even further and determines whether the most likely product of oxidation and leaching will be a wash ore or a heavy media ore and even to the direct shipping ores where the ratio of hematite to goethite is largely determined by the original taconite type. The relationship between original taconite, oxidized taconite, semitaconites, and wash and heavy media ores is briefly summarized in Table I. The terms are not precise and in some instances tend to overlap. The table is intended to point out only the essential differences between the various materials. The original taconite was dominantly composed of mixtures of magnetite, iron carbonate, iron silicate, and quartz (chert). In a few thin stratigraphic units, hematite was present as an original constituent. The alteration of the original taconite to oxidized taconite has resulted from the circulation of ground waters through an initial fracture system related to minor structures in the iron formation. The chemical reactions have involved the oxidation and decomposition of original minerals such as magnetite, iron carbonate, and iron silicates to hematite or goethite. The alteration at this early stage is characterized by pseudomorphic replacement of the original minerals by oxidation products although retaining the major textural features of the original taconite. There was very little secondary migration of iron at this stage and the total iron content of the rock has been only slightly increased. Further alteration of this material to form a semi-taconite, a wash or a heavy media ore, involves extensive removal of silica in solution and significant redistribution of iron units. Wash and heavy media ores are developed by the growth of coarse secondary iron layers, dominantly goethite, coupled with the removal of silica in solution and decomposition of the cherty layers. This paper is concerned primarily with the materials classified as oxidized taconites which are characterized by oxidation of the original mineral constituents with little secondary enrichment. The area studied, shown on the index map, Fig. 1, extends some 30 miles along the strike of the Biwabik formation roughly from Hibbing to Coleraine. This study was greatly facilitated by the basic stratigraphic and mineralogical studies of Gruner1 and white2. The bulk of the material in this presentation represents a portion of the author's contribution to a study sponsored by the Great Northern Railway on the oxidized taconites of the western Mesabi.3 METHOD OF APPROACH A total of 106 drill holes, representing some 30,000 ft of drilling, were examined and sampled. The drill holes were logged and some 1500 composite samples were prepared for chemical analysis and bench scale metallurgical tests. These samples were analyzed for total iron and ferrous iron; and magnetite iron was determined by a standard Davis tube test at minus 200 mesh. Standard reduction roast tests using 150-gram samples of minus 10 mesh material were made on these 1500 composite samples with a mixture of H2, CO2, N2, and H2O at a temperature of 650°C. This roasted material was pulverized through 150 mesh and concentrated in the Davis tube. The iron recoveries and concentrate grades obtained on the roasted products were used to assess the concentratability of the oxidized taconites. Detailed mineralogical work was done on thin sec-

Jan 1, 1964

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount, of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and-slimes. The reason for this is that in almost every, dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus,, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-day to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the .place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of. years, two general types of machines evolved for the treatment of fine sands and slimes :- The so-called concentrators and vanners, on the one hand, and the huddles and round tables on . the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By H. Furman Byars

INTRODUCTION of bottom dump hauling units into the Ray, Ariz., stripping operation of the Isbell Construction Co., was motivated by several reasons, with what appears to be debatable results. The accepted theory of truck design for use in open-pit holds that end dump vehicles are the most adaptable for the work. But, because operations of the bottom dump, under certain construction and haulage conditions, proved economically feasible, the unit was put to work in the Ray copper pit. The decision to try bottom dump was reached after considerable observation of the unit in action on construction of earth filled dams, levees, airport construction and several other similar tasks. Basic tire design also motivated the choice. All things being equal, a vehicle running on low pressure single tires will outperform another operating on dual high pressure tires, providing load carrying capacities are the same. The investment required to equip a vehicle with four single tires to handle the same load as one with dual tires mounted on two axles and single front axles is about 60 pct greater. Thus, in order to reach the break even point on tire costs, single tires must operate 60 pct longer. Comparison is made with a truck outfitted with 10 16:00x25 tires. Two other factors were considered in selecting bottom dump trucks. It was felt the bottom dump principle would work well in dumping ore into a hopper where gate design fits this particular method. Also, with the absence of hydraulic dumping, ore pollution with oil is reduced. The mechanical simplicity of the unit also lent weight to its choice. Ordinary reasoning indicated maintenance costs would be low compared with other units carrying similar loads. The bottom dumping principle is not new. It dates back to the days when horses were used to haul the same kind of rig. The unit employed at Ray holds 25 cu yd struck measure, or approximately 42 short tons. Dumping is accomplished by releasing an air cylinder opening a dog holding the doors. Doors are closed by a cable system operating off a wheel wind deriving power by friction with the trailer tire. The unit is mounted on four 27.00x33 and two 14.00x24 tires on the front axle. The power unit is a 300 hp Cummins engine. Hydraulic power boosts the steering. A straight mechanical drive and friction clutch with 10 speeds is used. Conditions Not Ideal Top performance of the truck can be expected only under the conditions for which it was designed, in particular grades under 5 pct, handling fine material, and dumping where one thin layer can be placed on top of another. The machine will handle 42 tons per haul, operating at high speed, with only seconds used for dumping. On a 2 or 3 pct grade over a one mile haul,

Jan 1, 1952

By Alfred E. Hunt

The late Alexander Holley said, on returning from a careful study of the relative merits of the Bessemer and the open-hearth processes, as shown in the best European practice, that, in this country, the open-hearth process would live to attend the funeral of the Bessemer ; and he said this several years ago, when in this country the Bessemer plant and practice had been developed to far outstrip that abroad, and when, proportionately, it had reached an advancement much beyond the improvements in open-hearth plants and practice. At the same time, the prevailing idea in the metallurgical world, a few years ago, seemed to be in favor of the substitution of Bessemer for open-hearth steel for most of the higher qualities, and Bessemer enthusiasts loudly proclaimed, that as good steel for all purposes could be obtained by their favorite process as by the open-hearth. It was, in fact, confidently prophesied that very soon tool-steel and similar grades, which consumers had learned to specify, in ordering, to be made by the crucible process, would by common consent be made by the Bessemer, as best adapted to give the desired results. But these expectations have failed to materialize; not only do the crucible people keep on in the even tenor of their way and talk with pride of their comparatively large outputs of " hundreds " of tons per month, as usual, but the open-hearth people have kept fast hold of their original domain of nearly the entire amount of sheared plates, of locomotive tires, of large forgings, spring-steel, agricultural steel, steel castings and the like. Further, owing largely to one of the great advantages of the Bessemer process, which is also one of its inherent dangers, namely, its large output, it has also fallen into considerable disrepute for structural purposes. Not a few experienced engineers are now stipulating in their specifications that Bessemer steel will not be allowed to be used, especially for tension-members.

Jan 1, 1888

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling,' forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has. been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses, and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

By H. R. Page, A. E. Jr Lee

From the inception of zinc retorting on a commercial scale in the United States in 1890,' the retort employed has undergone wide variations in its composition and manufacture, facilitating in part equally remarkable improvements in furnace capacities. The early day hand made clay retort was charged with carbonates or silicates or with coarse dead roasted concentrates mixed with a large proportion of charge fuel resulting in a relatively low zinc burden and fired 24 hr in direct coal fired furnaces. Its modern counterpart is fabricated in hydraulic presses from clay mixtures containing sizeable amounts of either silicon carbide or silica flour, charged with sintered flotation concentrates to more than three times the early day zinc burden and fired 24 to 48 hr in gas fired furnaces. This paper does not attempt to describe in detail the early day clay retort practice as it is well outlined in treatises by Ingalls,2 Lodin,3 Liehig,4 Hofman5 and others. A brief review of clay retort practice is presented together with a description of the major developments since 1912. Clay Retorts The Belgian type retort, both in the circular and elliptical forms, has been used almost exclusively. Typical dimensions of press made clay retorts around 1910 are shown in Table 1. Variations in these dimensions were used at different plants according to local conditions to a maximum inside diameter of 9 in. and inside length of 54 in. However, the effective heat penetration in a 24 hr firing cycle and the tendency of the retort to bend limited the retort size. Use of the elliptical vessel was an attempt to present a stronger cross-section resisting the tendency to bend and to increase the burden without increasing the depth of heat penetration. One exception to the 48-54 in. length was the 60 in. retort used as early as 1905 at Palmerton by means of supporting the last 12 in. at the butt end with a specially designed furnace back-wall. This backwall construction with the 60 in. retort had been developed and used at Bethlehem by G. G. Con-vers and A. B. DeSaulles. An attempt was made at Blende, Colo. to use even larger retorts of the Rhenish type based on European practice and requiring much higher furnace temperatures. Satisfactory plastic clays capable of withstanding these temperatures were not available, and the plant never operated successfully. PREPARATION OF BATCH Composition of the clay retort by weight was 40 to 50 pct raw clay and the balance "grog." Generally speaking the mix consisted of 7 parts plastic clay to 9 parts grog by volume. Principal source of the clay used was the Cheltenham vein—sometimes referred to as "St. Louis city clay." A typical analysis was A12O3-31.0 pct, SiO2-50.0 pct, Fe2O3-2.5 pct, MgO-0.3 pct, CaO-1.5 pct and loss on ignition 14.0 pct. At the smelter the clay was weathered whenever possible and then crushed to 0.08 in. or finer. Grog consisted of calcined adobies, cleaned retort scrap and cleaned refuse fire brick such as old furnace brick, blast furnace linings, and others. Saggers from ceramic plants and calcined flint clay were later used. The grog materials were ground to 0.12 m. or finer. Occasionally coke dust up to 10 pct of the mix was substituted for a part of the grog following European practice.² Particle size of the grog has a major influence on the retort properties—the larger the grain, the better can the retort withstand thermal shocks, resist bending at furnace temperatures and resist corrosion from slag; the smaller the grain, the lower the loss of zinc vapor through the retort walls. Grog forms the skeleton of the retort, and the clay shrinks around its grains to act as a binder. In the drying process, the grog has a stabilizing effect on the drying rate, decreasing shrinkage and giving up previously absorbed water to the surrounding clay to minimize the danger of cracking or checking.² Grog and clay were mixed through a horizontal pug mill with 10 to 20 pct water added, depending on whether the retort was to be formed by hand or mechanically, more water being required for the hand process. The batch or "mud" extruded from the pug mill was cut in convenient lengths for handling, stacked in piles or in special rooms, covered with wet burlap and allowed to "rot" or age from 1 to 8 weeks to increase plasticity. HAND MOLDING If the retort was to be molded by hand, the mud was repugged after the rotting period and given to the molders. Their molds consisted of 3 sheet iron or wood cylinders, each one third the retort length and defining the outer shape of the retort. Beginning with the bottom section, mud was placed in the form and tamped with a rammer

Jan 1, 1950

By D. J. Rose, W. M. Armstrong, A. C. D. Chaklader

The wetiability of single crystals of MgO by specimens of vacuum-cast iron was studied using the sessile drop technique in vacuo at 1550ºC. Formation of FeO at the liquid-vapor interface caused the contact angle (6) to decrease from 117 to 65 deg during the first minute. After cooling, all specimens possessed a peculiar annular interfacial deposit of Fe,O,. Within the annulus the interface showed no sign of chemical attack. Chemical reaction occurred where the iron was alloyed with Ti, V, Cr, Nb(Cb), Ta, cmd Zr. Vnriation of 6 with alloy concentration was studied. Although vanadium md chromium improved the wettability of MgO by iron, the effect of Zr, Ti, Nb, and Ta was indeterminable because the 8 derived from sessile drop considerations was that of the metal against a restrictive peripheral volume of liquid oxide wetting the substrate. INTEREST in the nature of metal-ceramic interactions has been stimulated by progressive development of metal-ceramic combinations. One of the more valuable methods used for bond investigation is the sessile drop technique. Recent attempts to improve wettability through solute additions to the drop have revealed that the solute may a) react with the oxide creating new compounds at the solid-liquid interface, b) adsorb at the interface in a monolayer formation, or c) distribute throughout the drop uniformly causing no wettability variation. This work, part m in a series1,2 of investigations of interface reactions between metals and ceramics, embraces a study of the Fe-MgO system. MgO possesses a large negative free energy of formation (-173 kcal per g mole 0, at 1550ºC) compared to FeO at this temperature (-73 kcal per g mole 02). Hence the electronegativity difference between the drop and substrate allows selection from an extensive group of metal solutes with intermediate electronegativity differences that would, in the absence of chemical reactions, be expected to adsorb pre- ferentially at the solid-liquid interface. However, the high oxygen pressure of MgO in vacuo creates an oxidation environment which influences the solute behavior. Recent studies of the Fe-MgO systemJ74 have been restricted by chemical reactions that obscured observations. In view of the current interest in liquid-phase sintering of metal-ceramic combinations under partial oxidizing conditions,5 a more comprehensive study of the Fe-MgO system seemed beneficial. EXPERIMENTAL PROCEDURE 1) Specimen Preparation. Optical-grade MgO single crystals and Ferrovac vacuum-cast iron were used in all experiments. A spectrographic analysis of the iron indicated 0.008 C, 0.05 V, 0.005 Mo, 0.01 Ti, 0.002 S, 0.01 Cr, 0.001 Mg, 0.01 Si, 0.003 A1 (wt pct). The MgO crystals were cleaved along (100) planes into plates approximately 20 by 20 by 1 mm. Following annealing in vactto at 1100°C for 3 hr, surface irregularities were removed by a chemical etch in phosphoric acid at 100°C. The iron rod was machined into small cylinders approximately 0.250 in. in diam and length and these were carefully cleaned in organic and acidic solutions to remove surface impurities. All specimens were weighed to the nearest 0.1 mg. 2) Apparatus. The apparatus described in detail by previous authors1,2 was modified for this work. A Polaroid Land Camera was incorporated into the optical system so that drop measurements at ten-second intervals after melting were possible with ultra-high-speed self-develop ing film. 3) Procedure. The iron cylinders were placed upright on the MgO plates and positioned in the molybdenum susceptor. After furnace assembly the system was pumped down to a vacuum of 1 µ and flushed with H2 at 800°C. The system was again evacuated to 5 x 10-5 mm of mercury and the temperature raised to 1550°C within 2 min. The molten drops were photographed at appropriate time intervals. TWO min after melting the iron vapor pressure caused gas discharge, or corona, within the tube. The specimens were then slowly cooled to room temperature, sectioned and examined metallographi-cally. X-ray identification of interfacial reaction products was attempted by the powder diffraction technique. Alloying elements (Ti, V, Cr, Zr, Ta, Nb) were added to the iron in various concentrations up

Jan 1, 1963

These pages may be used as order sheets. Mark the number desired opposite title of pamphlet wanted, add your name and address, tear out the sheets and mail them to us. Single orders 25 c. Pamphlets 10 c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlets of the same or different titles, when cash accompanies order. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long, as the supply lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets-that have been published by the Institute. Any other paper published by. the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare. The, Institute is still selling back volumes of Transactions at reduced prices, but some of these volumes are becoming rare. and members who desire to complete their sets of these very important books on mining and metallurgy are advised to send in their orders as soon as convenient. The attention of members is also called to the bibliographical index of the science of ore deposits contained in the Emmons Volume which is selling at $3 in paper and $4 in half morocco. The Posepny Volume is already exhausted and members who do not get in their orders for the Emmons Volume at the present reduced price may soon find themselves unable to obtain it on such favorable terms.

Jan 7, 1917

By B. G. Matson, M. A. Whitfield, G. R. Dysart

This paper describes the development of u computer program to calculate changes that occur in the length of tubular goods due to temperature and pressure changes during stimulation operations. Due to the numerous variables involved and the uncertainty of all static and dynamic conditions that could exist, it becomes a staggering task for individuals charged with completions to perform the necessary mathematical calculations. The computer program permits advance calculations for several sets of conditions. INTRODUCTION In the Delaware basin of West Texas alone, 50 wells were contracted or drilled to 15,000 ft or deeper in 1965. Deep well activity is continuing in this and other areas on an expanding scale. Many of these deep wells require extensive stimulation for successful commercial production, and during these operations, pressures and temperatures are encountered that have a pronounced effect on the length of tubular goods. This length change during a large-volume, high-pressure stimulation treatment utilizing fluids considerably cooler than bottom-hole temperature can be of such a magnitude that permanent damage to casing and tubing will result unless mechanical design, pressures and fluid temperatures are evaluated and controlled. These pressure and temperature effects can be calculated. However, the process lends itself well to computer solutions because of the mathematical nature of the problem and the calculating hours involved in arriving at an answer. The engineering-hour demand becomes more severe as tapered strings are involved. On initial treatments on a given well, surface pressure and injection rate conditions are unknown, and offset well conditions have not proven to be a reliable method for making predictions. For these reasons, it has become rather standard procedure for operators to compensate for these uncertainties by placing unnecessary pressure and fluid temperature restrictions on stimulation design. On a number of occasions treating fluids have been preheated to as much as 160F as a means of compensating for thermal contmction resulting from pumping cool fluids. The maintenance of packer seals has been treated by Lubinski, Althouse and Logan',' and the problem of therma1 effects on pipe has been explored by Ramey." These works were expanded and the results made applicable to everyday oilfield terminology before submitting them to computer programming. The pressure and temperature effects on tubing movement previously mentioned occur simultaneously as fluid moves through the pipe. The pressure changes, for purposes of explanation, are categorized here as to the various effects these pressures have on a tubing string. These divisions are (1) the piston-like results of forces acting on horizontal surfaces exposed to pressure, (2) swelling or ballooning of the tubing along its entire length due to the forces of pressure acting against the tubing walls, (3) the elongation of tubing due to frictional drag and (4) corkscrewing of the pipe due to internal pressure. Thermal changes are also of great importance, as their results may be more significant than any of the pressure effects. Steel is an excellent conductor of heat and the earth is a relatively poor conductor. It has been calculated that pipe temperatures at depths of more than 20,000 ft approach within as little as 25" the temperfature of the surface fluid after pumping for 2 hours, or a drop in temperature in some treatments of more than 220F. The equations presented in this paper were developed for computer programming and simplicity of input information; therefore, numerical constants such as Young's modulus for steel (28 X 10\ si), the coefficient of thermal expansion of steel (6.9 X 10."IF) and Poisson's ratio for steel (0.3) are included with unit conversion factors. The moment of inertia of tubing cross-sectional area with respect to its diameter was changed to a constant times (D' — d') where D is outer diameter and d is inner diameter. Units in the equations are length in feet, diameter in inches, density in pounds per gallon, pressure in psi, rate in barrels per minute and time in hours. PISTON-LIKE REACTIONS A change in tubing internal dimensions and the exposure of other horizontal surfaces to different pressures on the inside and outside of the tubing result in a reaction much like a piston under pressure. Such is the case when the internal diameter changes in a combination string of pipe, when seals of a slick joint assembly are subject to pressure and in the end effects of a tubing string. The change in tubing length due to the piston effects of a slick joint packer is affected by the various diameters involved, the tubing pressure Ap,, the casing pressure ,Ap,, length of pipe L, densities of fluid in the tubing before and during pump-

By Lynn Howell

IN a previous articles we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon Which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in 'the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.' Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added. inside the chamber, This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously, Briefly described, the chamber moving in the hole is made of 3,2-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft, long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber, Above this is the vacuum-tube amplifier with its batteries and transformer, In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube, Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1939

By J. E. Nesset, J. A. Finch

A model of the fully-loaded condition of particle accumulation on the matrix of a high gradient magnetic separator is developed. The model accurately predicts the build-up profiles reported recently by Friedlaender et al. A powerful development from the model is that loading (volume of accumulated material per unit volume of matrix) is uniquely defined by a dimensionless group, called the loading number, NL. From direct measurements, NL proved superior to the dimensionless group proposed by Watson as a measure of loading. The fine size limit of hematite recovery is examined using NL.

Jan 1, 1980