Search Documents

The John Fritz Medal is awarded from time to time for notable scientific or industrial achievement by a board composed of representatives from the four engineering Societies. The members of the Board of Award for 1917 are: A. S. C. E. A. S. M. E. George F. Swain Ambrose Swasey, Charles Warren hunt, John, A. Brashear, Charles D. Marx, Frederick R. Hutton, Clemens Herschel. John R. Freeman. A. I. M. E. A. I. E. E. Gybbon Spilsbury, C. 0. Mailloux, Charles F. Rand , Paul M. Lincoln, Christopher R. Corning, John J. Carty, Benjamin B. Thayer. Harold W. Buck. The John Fritz Medal was awarded in January, 1917, to Dr. Henry Marion Howe, for his "investigations in metallurgy, especially in the metallography of Iron and Steel." The presentation ceremonies were held in the Auditorium of the United Engineering Societies' Building, New York, on Thursday evening, May 10. Mr. Ambrose Swasey, Chairman of the John Fritz Medal Board of Award, presided, and addresses were delivered by Dr. Rossiter W. Raymond, Secretary Emeritus of the American Institute of Mining Engineers, and Dr. Ira N. Hollis, President of the American Society of Mechanical Engineers. Professor Albert Sauveur, Chairman of the Board at the time the award was made, presented the medal, and the ceremonies concluded with the response of Dr. Howe.

Jan 7, 1917

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By G. W. Crane

When ore was discovered on the Tintic Standard property in the spring of 1916, new developments were immediately started both north and south of that property, on the supposition that in East Tintic the ore would be found to occur in northerly trending channels, similar to those so characteristic of the older camp. But 9 years of developments have failed to establish the existence of such a channel. This is due undoubtedly to important differences in the geology of the two camps, that were not recognized, and is indicative of the danger in the general tendency toward interpreting the geology of East Tintic too strictly in terms of that of the older camp. It should not be forgotten that while the two sections have had practically the same geological history, the net results of a long series of geologic processes have developed in them conditions that differ so widely and in so many particulars that the necessity of regarding them as essentially different districts seems apparent. In an effort to emphasize this fact, this paper is devoted chiefly to a comparison of the geological conditions as found in the two camps and is addressed more particularly to those familiar with the geology of the Tintic district. Following a short description of the several ore discoveries and of the Tintic Standard mine is a brief discussion of the evidence of ore channels in East Tintic. For my information regarding the Tintic Standard mine, I am indebted to the courtesy and generous assistance of Messrs. Wade and Snow of the Tintic Standard Mining Co. East Tintic District The Term East Tintic district is here used to represent that eastern part of the Tintic mining district lying between the productive portion of the old camp of Tintic on the west, the foot hills of Goshen Slope, on the east, the Denver and Rio Grande Railroad on the north, and Silver Pass on the south, all in Utah County. As represented by the geological map, Fig. 1, it includes an area about 4 miles wide, east and west, and 5 miles long, north and south, within which the Tintic Standard mine is about centrally located. The map is a compilation of data supplied, for the most part, by the Chief Consolidated Mining Co. and represents the

Jan 1, 1927

By G. P. Tiwari

Recrystallization and grain growth in thoria dispersed nickel and nichrome were recently studied by Webster as a function of temperature and deformation. The unexpected part of these results was that specimens which had received heavier deformation developed greater resistance to recrystallization. Retardation of recrystallization was accompanied by the formation of voids around thoria dispersion. To explain these results, Webster suggested that the formation of void around the particles increased the effective size of thoria particles. This resulted in greater impediment to the grain-boundary migration and as a consequence the recrystallization of the matrix is retarded. In the present note an alternative and more probable explanation for the effect of voids on recrystallization is presented. The exact mechanism of void formation in thoria dispersed nickel or nichrome is not known. However, it is reasonably certain that it must be preceded by the stress concentration in the matrix around thoria dispersion during the deformation.'' The resulting stress concentration must be sufficient enough to supply the surface energy for the new surfaces created. Further, the decrease in the strain energy of the matrix surrounding the potential void nucleus must be larger than the surface energy of the newly created surface. The release of strain energy due to formation of crack results in a strain free cylinder of the material around the voids.13 If the void formation is not localized, at few points only (as is the case here), this process may lead to considerable amount of release of strain energy of the matrix. The pattern of recrystallization behavior of single phase homogeneous matrix as well as the matrix having a second phase dispersion is same except for the fact recovery and recrystallization are more clearly delineated.14 In general, the recrystallization temperature is lowered (i.e., recrystallization is easier) with increase in the amount of cold work. This is due to the increase in stored energy in the matrix with increasing amount of deformation. If somehow there is a relaxation of strain energy in the matrix, the recrystallization should become difficult because of the decrease in the amount of stored energy available for recrystallization. Since the formation of voids leads to a decrease in the strain energy of matrix, the recrystallization of the matrix would be inhibited due to the formation of voids during deformation prior to recrystallization. It has been observed by earlier workers15'16 that the presence of preexisting voids in a matrix retards the recrystallization. The essential issue here is how do the voids act to produce this effect. If the voids influence recrystallization only by blocking the grain boundary migration, then the effect should be maximum when they are present almost exclusively along grain boundary. These conditions are obtained during high temperature deformation. However, the voids produced due to creep along grain boundary are not able to prevent recrystallization17 suggesting that they are not effective in blocking grain boundary movement. Recently it was shown by Davies and Williams that the voids can act as sinks for vacancies." As a result the processes dependent on vacancy diffusion like recovery, recrystallization, dislocation climb, and so forth, will be hindered. This fact may be responsible for inhibition of recrystallization during subsequent deformation and annealing cycles. It is to be noted here that there is a large difference between the density of voids in creep experiments and the other experiments where retarding effect of voids on recrystallization is seen. The voids in former may number up to l04 to l05 per sq cm whereas in latter cases the voids density is typically around 1010 to 1013 per sq cm. It appears that the decrease in supply of vacancies in creep is insufficient to adversely affect the recrystallization due to low void population. The author is grateful to P. Das Gupta and S. P. Ray for helpful discussions. Author's Reply D. Webster Tiwari appears to have misunderstood the nature of grain boundary-particle interactions. Tiwari (quoting Cahn) states that second phase particles become more effective as they become smaller, therefore as the voids in TDNiC make the thoria particles effectively bigger their ability to resist grain boundary movement is impaired. This particle size argument was originally proposed in the form of an equation by Zener 20 years agol9 and is not necessarily valid as is discussed below. However, assuming it is valid, it predicts a greater boundary restraining effect by smaller particles simply because their combined cross sectional area is greater at a constant volume. If the number of particles remains the same and their effective size increases, as in the present case, Zener's equation predicts a greatly reduced grain size. This is because the effect

Jan 1, 1970

By C. P. Walker

Determining the distance to remote objects by observing the time required for sound to traverse the intervening space is an old practice. Attempts have been made to use this method for determining the fluid level in oil wells but as far as the writer is aware it was not found to be practicable, because vibrations in gas in the audible frequency range do not travel as well and as far as low-frequency pressure waves, which are capable of transmitting a greater amount of energy than can be transmitted by audible waves. Wood, in his book "Sound," states that in a given medium the range of sound transmission will vary inversely as the square of the frequency. The fact that the sound from a whistle having a low tone has a much lower attenuation rate than that from a whistle of high pitch is well known. Also, the pressure waves caused by cannon fire often rattle windows at points so distant that no sound of the cannon is heard. In 1932 P. E. Lehr and H. T. Wyatt, of the Shell Oil Co., experimented with the principle of the concussion, or pressure-wave echo, method of determining fluid levels in oil wells. They released compressed gas into the top of the casing, thereby creating a pressure wave, which traveled down the well and back again. Their experiments proved conclusively that, with the proper apparatus for recording the echoes and determining the velocities at which the waves travel, the method could be used successfully for determining fluid levels in oil wells. Wells are often equipped with from one to three tubing catchers and these together with the top of the liner are frequently above the fluid. Each of these obstructions reflects a part of the pressure wave. In such wells there may be, therefore, as many as five pressure-wave reflections. Thus it is obvious that in order to identify the various reflections and to determine therefrom the fluid level in a well it is necessary to obtain a graphic record of these reflections.

Jan 1, 1937

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By G. Sachs, J. W. Spretnak

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By Charles Colcock Jones

In any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly not due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul. "Ore Supply Edwin C. Eckel, in his monumental work on Iron Ores, has but little to say concerning the Pacific Coast deposits. He mentions (p. 269) those of Minaret, Madera County, and the Eagle Mountains, Riverside County, Cal., "perhaps 50 to 100 million tons each;" the deposits in Shasta County, worked for the electric furnace on Pitt River; and

Jan 1, 1916

By G. R. M. Del Giudice

The term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(l)† Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince;(3) Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) Old Theory of Slime-coatings At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince's experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed. The cell was made of bakelite and had platinum electrodes. Objectives were employed which had a working distance of at least three millimeters,1 and the parts of the mounting which came in contact with

Jan 1, 1935

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytic expressions were developed and applied in two preuious papers to predict effects of solidification variables on macrosegvegation. In this paper, experiments are reported to test the analyses quantitatively and qualitatively. Good quantitative agreement is obtained between predicted and measured compositions for the following types of segregation (all experiments were on laboratory-size ingots of Al-4.5 pct Cu alloy): (a) inuerse segregation, (b) composition distribution in ingots solidified with unidirectional heat and fluid flow, (c) simulated centerline segregation, and (d) segregation resulting fro, change in solidification cross section. In addition, qualitative agreement of prediction of theory with experiment is obtained for (a) segregation resulting from sudden change in heat extraction during solidification, (b) centerline segregation in a bidirectionally solidified ingot, and (c) under-riser positive segregation. IN two previous papers,''2 it was shown that a variety of apparently different types of macrosegregation result from the same basic mechanism. This mechanism is the flow of solute -rich liquid to feed solidification and thermal contractions. Analytic expressions were derived and examples given of their application to predict macrosegregation. Calculations were for Al-4.5 pct Cu alloy. In this paper, we describe a series of experiments designed to test results of the foregoing calculations. All experiments were on laboratory-size ingots (weighing 10 lb or less), of A1-4.5 pct Cu alloy, nominal composition. APPARATUS AND PROCEDURE A typical mold and chilling arrangement used for unidirectional solidification is shown in Fig. 1. Before casting, this assembly was placed in an electrically heated air furnace, and heated to 680" to 700°C. When the plaster reached the desired temperature (usually 1 to 2 hr after the furnace temperature), the mold was filled through a funnel extending from the outside of the furnace into the cavity. The assembly, with liquid, was held for several minutes to allow convection to subside. The coolant, either air or water (depending on the desired solidification rate), was turned on and the ingot solidified. With the four sides and top insulated, heat removal for solidification was through the bottom surface, resulting in a fully columnar structure. Design of the casting cavity was varied, as discussed below, to produce desired macrosegregation effects. However, for castings solidified with unidirectional heat flow, the top was always open to the furnace atmosphere and temperature. The bottom sur- face rested on a chill through which the heat was extracted, and all other surfaces were insulated with plaster. In one case to be discussed, the mold design was changed to obtain bidirectional solidification. In this case, two vertical chills were used (on two faces of the mold) and the bottom was insulated. In a last case discussed, that dealing with under-riser segregation, experiments were conducted in bottom-chilled sand molds at ambient temperature. Except for this one case, all experiments were conducted in the electrically heated air furnace as described above. In many ingots, thermocouples were used to obtain continuous records of solidification. In all cases, these were chromel-alumel couples with output continuously monitored on a twelve-channel recorder. Where thermocouples were employed, these were embedded in the refractory mold walls during mold-making so their heads extended to the vertical centerline. Six to nine couples were employed, placed at intervals from the chill. METAL-MEL TING PROCEDURE Aim analysis was A1-4.5 pct Cu; alloy was prepared from high-purity aluminum (99.9 pct Al) and A1-Cu master alloy (50 pctOFHC Copper, 50 pct high-purity Al). The A1-4.5 pct Cu alloy was cast in 5- to 7-lb ingots for subsequent remelting for the macrosegregation experiments. Melting for ingot casting was as follows. After preheating the melting crucible for an hour or more, the charge was melted and superheated to a temperature of 690" to 720°C. After stirring, the melt was degassed with chlorine for 10 min. After stirring again for 1 min, a gas sample, under reduced pressure, was taken. When the sample was gas-free, the crucible

Jan 1, 1969

By A. M. Talbot, John T. Norton

TheRe is still considerable controversy as to the exact nature of the mechanism of the age-hardening process, in spite of the many experiments already performed. For this reason, a considerable number of typical systems should be examined in detail and their results correlated. Furthermore, the methods of studying the changes that take place during the progress of this phenomenon should be carefully scrutinized and the different methods applied to the same samples, preferably at the same time. The experiments described in this paper are presented to supply information on one age-hardening system and to show how the various methods of investigation compare in their indication of what has happened. In brief, the progress of aging in magnesium alloys containing about 10 per cent by weight of aluminum at different temperatures was followed by measurements of hardness, electrical resistivity, dilation and lattice parameter, and by microscopic observation. Previous Work Meissnerl,$ Archer?, and Gann3 have investigated the changes in mechanical properties of magnesium-aluminum alloys during aging and have shown the optimum condition for the age-hardening treatment. Meissner's results are particularly interesting because when replotted so that they represent hardness as a function of aging time, the curves of 125" and 150" C. show two hardness peaks. This result was not confirmed in the present work. Schmid and Siebe14 have reported an investigation that is similar to the present one but it was not published until the present work had

Jan 1, 1936

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.' A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By Alden B. Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is. one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investigations have been. confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.-Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Lane X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935

By R. W. H. Atcherson

BLAST-FURNACE flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers acid more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of flue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained are shown in Table 1.

Jan 2, 1920

By A. M. Gaudin, T. P. Meloy

Based on the equation for single fracture, a formula has been obtained for repeated fracture. Solution of this equation is obtainable analytically for a few examples and numerically for all others. Graphs of the size distribution equations have been obtained; they agree broadly with the experiments of others. In another paper1 we have considered a model and a comminution distribution equation for single fracture of brittle materials. Most comminuting devices, however, depend on the occurrence of repeated fracture. This is especially true of continuous cylindrical mills of the ball, tube, or rod type. But even in primary crushers there is some repetition of the breaking process, so that this paper should be of interest in connection with all comminuting devices. HALF LIFE AND PROBABILITY OF FRACTURE To facilitate the study of fracture it is useful to introduce the concept of the half life of a particle, In the ball mill, for example, we may start with 10,000 feed particles. The time, 7, by which one half of these particles have been broken is the half life of the feed under the prevailing experimental conditions. The probability of breakage bears an inverse relationship to the half life. In a ball mill, for instance, it can be shown that the

Jan 1, 1962

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By Mary Louise Theodore, R. G. Aspden, D. A. Colling

T RACES of sulfur have a marked influence on the physical and mechanical properties of many iron-base alloys. The commonly used combustion method for the determination of sulfur content is not accurate enough at the 50 ppm level by weight and below to be useful in determining the influence of sulfur. Kriege and Wolfe' have described a method for the determination of sulfur in iron alloys in which the sulfur is evolved as hydrogen sulfide followed by reaction with N, N-dimethyl-p-phenylenediamine, and iron (111) to form methylene blue which is measured spectrophoto-metrically. This method of determining sulfur has been used to study the activity of sulfur in Fe-Si-S alloys,' but has not been previously applied to the determination of sulfur in Fe-Ni alloys because of the insolubility of nickel in dilute hydrochloric acid. Dissolution of nickel in dilute hydrochloric acid, however, can be greatly accelerated by the addition of a small amount of platinic chloride.3 By combining these two techniques in a procedure in which 0.005 pct platinic chloride in 1:l hydrochloric acid is used as the dissolving fect on the strength of the material. However, ductility is influenced by the presence of discontinuous precipitation. In Fig. 5, percent elongation data at room temperature and 1400°F is shown for two sets of specimens of Waspalloy which were solution heat treated at 1950°F and either quenched or slow cooled to the aging temperature and then aged for 100 hr at 1292" and 1598ºF, respectively. At room temperature the existence of a discontinuous precipitation cell at grain boundaries (see data point marked by arrow) has no apparent effect on ductility. However, at elevated temperatures a pronounced lowering of ductility occurs when discontinuous precipitation has occurred in the specimen. It would appear that the morphology of discontinuous precipitation "cells" at grain boundaries would be highly conducive to the initiation of cracks which in turn lead to premature "grain boundary" failure.

Jan 1, 1970

By George Ross Green

[In discussion of the paper of Mr. J. C. Bayles, read at the New York meeting of September, 1890, Trans., xix., p. 18.1 It is often so difficult to locate the causes of failures of machinery and apparatus which can be examined and studied at leisure, that it is not surprising that the causes of explosions should escape detection. Usually the explosion is the first evidence that anything is amiss, and the time for observing the conditions is necessarily brief. An incident in a welding-works near Essen, Germany, might be cited as exemplifying what trifling causes may lead to disaster, and how difficult, under the most favorable conditions, it may be to discover them. A blowing-engine was arranged with two suction-pipes at each end of the blowing-cylinder—one leading to the air, and the other to the gas-holder. Each pipe was provided with a valve, and all were so adjusted that the cylinder drew in gas and air in the proportions found most advantageous. The gases from the cylinder were carried directly to the furnace through suitable pipes, and while the cylinder was provided with relief-valves, every effort was made to prevent explosions, principally by compressing the gases to a point where the rate of efflux of the mixture was greater than the velocity of combustion, if the expression is here allowable. It was found that the apparatus would work satisfactorily for some time, and then the relative proportions of the mixture would change, and an explosion might have been the result. Experiments consuming days were made to discover a method of averting this danger, but they were unsuccessful, until it was observed that the change in the composition of the mixture of gas and air took place when the gasometer began to rise or fall—the back-pressure due to friction when the holder was rising or its absence when falling being sufficient to change the conditions. As soon as this was discovered,

Jan 1, 1892