Search Documents

By E. S. Machlin, A. J. McEvily

HE results of an experimental investigation by McEvily and Machlin have indicated that a strong relationship exists between the processes of cross slip and fatigue. Whenever dislocations can cross onto an intersecting plane and expand thereon, as in AgCl crystals, the usual type of S-N behavior is obtained, but when such a process is difficult, as in NaCl crystals, fatigue does not occur in its usual manner, if at all. MgO, because of its crystal structure (NaCl type) and slip systems ({110}<110>) would not be expected to fail in fatigue. However, Cornet and Gorum2 have found something akin to the usual type of fatigue behavior for MgO crystals. The purpose of this note is to attempt to resolve this apparent discrepancy. In Cornet and Gorum&apos;s work as-cleaved crystals were tested under cyclic axial loading, whereas in McEvily and Machlin&apos;s work chemically-polished crystals were tested in reversed bending. Because of the difference in specimen preparation, the major effort of the present work was directed toward comparing the behavior of as-cleaved as opposed to chemically-polished specimens. The effect of type of loading seemed less important, but a check was made on this also. Eighteen bend tests and one axial load test were made. The specimens were cleaved from Norton magnorite blocks, and measured 1 by 3/16 by 1/8 in. To avoid failures in the grips, the thickness of the bend specimens was reduced from 1/8 in. near the ends to 0.04 in. in the central portion. This reduction was from one side of the crystal only. Twelve specimens were polished in orthophosphoric acid to remove the damage due to cleavage. The other six specimens were not chemically polished so as to maintain the as-cleaved condition of the crystal faces which had not been reduced. The axial-load specimen was reduced from both faces to a thickness of

Jan 1, 1962

By John P. Dolan, Charles A. Einarsen, GiIman A. Hill

his paper discusses how the following formation characteristics can be determined mathematically from drill-stem test pressure charts: true formation pressures, effective permeability of the entire section tested, well productivities, wellbore damage, and possible detection of barriers (faults, pinchouts, etc.). This paper also presents a practical method for im-mediate determination of eflective permeability and well-bore damage from successful double shut-in pressure tests. A list of recommendations for improving the reliability of drill-stem rest pressures is also presented. INTRODUCTION A drill-stem test is a temporary completion designed to sample the formation fluid and to establish the possibility of commercial production. Early pressure recording devices were used merely to verify proper operation of the testing tool. Until recently the accuracy of the pressure gauges has been insufficient for any reliable quantitative use of the recorded pressures. In view of the need for more reliable formation evaluation and as a result of the recent interest in exploration work employing the concept of hydrodynamic en-trapment,1,2,3,4 better pressure recording gauges are now in use. These devices can record pressure within 1 per cent above 1,000 psig and can detect differential pressures as low as 1/2 psig. In addition to formation pressure, several other reservoir characteristics can be determined from DST charts; namely, well productivity, formation permeability, wellbore damage, and the possible existence of bar- riers (faults, pinchouts, changes in permeability, etc.). This paper presents a practical method to interpret DST pressure charts for formation pressures and many other reservoir properties, a method that has been developed in analyzing approximately 4,000 DST charts during the last five years. The techniques used are a composite of published articles on drill-stem testing5,6, together with well-known pressure build-up analysis methods. THEORY It has been shown7,8 that the following equation may be used for analysis of pressure build-up curves: Po - Pw = 162.6 qu/kh log ( to + ?/?) .....(1) When this equation is applied to the curves obtained in drill-stem testing, the assumptions and boundary con-ditions are more nearly realized than in conventional flow and build-up tests on producing wells. Zak and Griffen9 have recently discussed in detail the use of this equation in analyzing DST charts. One of the problems with DST curves is the lack of reservoir data for precise analysis. Therefore, it is necessary to develop empirical rules and field methods for analyzing DST charts in quantity. For this reason, the empirical methods presented in this paper have been developed, and their derivation is found in Appendices A and B. METHOD USED FOR ACCURATE READING OF DRILL-STEM TEST CHARTS In order to apply the pressure build-up theory to DST charts, it is necessary to obtain a digitized expression for the pressure and time data recorded by the pressure gauge. These data may be either provided by the service company or interpolated by projecting a

Jan 1, 1958

By W. C. Winegard, J. E. Gruzleski

The stages in the development of cells in the Sn-Cd eutectic have been studied by unidirectionally solidifying specimens under known conditions of growth rate, temperature gradient, and impurity concentration. By means of a quenching technique, the shape of the solid-liquid interface during solidification could be observed. Cells are shown to develop from defects or depressions which exist on the solid-liquid interface of even a pure eutectic. Th,e container wall, grain boundaries , and fault lines in the micro structure play an important role in cell development. A two-phase eutectic dendrite found at high impurity concentrations is described. L HE cellular or colony structure formed during eutectic solidification caused much confusion among early workers in their attempts to classify eutectic structure, and a major advance in our understanding of eutectic solidification was made when the colony structure was identified with a cellular interface caused by the presence of impurity elements.1&apos;2 To date, however, no detailed investigation of the stages in cell development in eutectics has appeared, and little work has been done on the cell morphology. The present paper presents the results of such an investigation. EXPERIMENTAL The Sn-Cd eutectic was used in this investigation with lead as the impurity element to promote cell formation. Materials of 99.999 pct purity were zone-refined to an approximate purity of 99.9999 pct. Alloys as close as possible to the eutectic composition, 67.75 wt pct Sn, were prepared using zone-refined tin and cadmium. The alloys were then zone-melted to the exact eutectic composition, as described by Yue and Clark,3 using a total of twenty to twenty-five passes on each eutectic bar. Only those portions of the bars which contained no primary phases were used in subsequent experiments. Master ternary alloys were prepared by melting together the required amounts of lead and the Sn-Cd eutectic in a sealed Pyrex tube under argon, and these alloys were then diluted with pure Sn-Cd eutectic as required. Unidirectional solidification was conducted vertically upward using the two-element resistance furnace shown schematically in Fig. 1. With this apparatus, it was possible to obtain a range of growth rates and temperature gradients so that the cell structure could be studied under different growth conditions. Growth rates in the range of 0.4 to 9.1 cm per hr and temperature gradients from 2.25° to 1475°C per cm were used. To ensure steady-state solidification, power to the furnace was stabilized, and the entire apparatus was enclosed in a large box in which the temperature was controlled to within ± 0.2°C. The apparatus was arranged so that the specimen could be quenched in situ during solidification by pouring a large quantity of water down the central vycor tube. Excellent delineation of the solid-liquid interface at the time of the quench was obtained because of the structural changes accompanying the rapid solidification of the remaining liquid. The quenching rate was always extremely rapid as no evidence of a transition in the lamellar spacing at the interface was ever observed. The alloys to be solidified were contained in degassed, high-purity graphite tubes, 1 cm OD and 0.6 cm ID. The specimens were about 18 cm in length. After the alloy had been cast into the tubes, three 0.8-mm holes were drilled in the tube to the center of the specimen. One hole was placed 1 cm from the bottom of the ingot, and the other holes were placed at 8 and 9 cm, respectively, from the base of the ingot. Thirty-four-gage chromel-alumel thermocouples were sealed in the holes. The lower thermocouple was used to position the solid-liquid interface at the start of each experiment,

Jan 1, 1969

By Tell Ertl

The term oil shale is defined. Foreign oil-shale developments are outlined briefly. The richest and most extensive oil-shale deposits in the United States lie in western Colorado. The Bureau of Mines is opening two adjacent areas for underground mining. in western Colorado. From the first area the oil shale is mined selectively as required by the retorting plant. The second area is being developed as a unit of a full scale oil-shale mine to ascertain the most practical methods of mining oil shale and to determine costs. In both of these mining areas, research will be carried on to develop new and improved practices for mining oil shale. Introduction Oil shale is a sedimentary rock containing a solid mineraloid of indefinite composition known as kerogen. On heating oil shale, the kerogen undergoes thermal decomposition and some of the vapor products of the decomposition can be condensed as shale oil. Oil from shale can be a major source of liquid fuels since extensive deposits of oil shale are known to exist throughout the world. The United States considers the establishment of an oil-shale industry only when doubt exists of the adequacy of the domestic supply of crude petroleum. On the other hand, oil shale is not strange to foreign oil men. The industry is an old one in other parts of the world. The French industry has been in existence since 1838, the Scottish since 1859, the Australian since 1860, the Estonian and Swedish The since World War 1, and the Manchurian industry since 1929. The most highly exploited oil-shale deposits are the Carboniferous shales of Scotland. About 20 seams ranging from 4 to I2 ft in thickness are worked. The yield during recent years in scotland has been 18 to 25 gal of shale oil per ton, from 3&"30&apos;000 tons per year&apos; The French and Swedish oil-shale deposits are of lower grade than the Scottish. The Estonian oil-shale deposits are 7 ft thick, and the oil yield averages 50 gal per ton. Over 1,000,-ooo tons are mined each year, half of which is used directly as fuel to substitute for coal and the other half is used for the production of oil. Immense deposits of oil shale that will yield 10 to 15 gal per ton exist in Germany. Because of the impending loss of the Rumanian and Polish oil fields and the bombing of synthetic liquid fuel plants, the Nazis in 1943 started a large-scale oil-shale program in Germany. By V-E Day, it is said, oil-shale production had reached the rate of 2500 tons per day and rapid expansion of the industry was imminent. Australian oil shale, known as torbanite, occurs in beds 2 to 6 ft thick. It is of a very high grade and on retorting yields 80 to 160 gal per ton. The oil-shale industry of Manchuria was the largest in the world during the past decade. The well-known Fushun coal deposit in Manchuria has an overburden of 500 million tons of oil shale about 450 ft thick that will yield 10 to 15 gal of shale oil per ton. The oil shale is

Jan 1, 1949

By Donald R. Reichmuth

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker&apos;s "Annotated Tables of Strength and Elastic Properties of Rocks."1 There are now three distinct approaches being used to determine the tensile strength of brittle materials. These are shown schematically in Fig. 1. The first method consists of simply pulling the specimen apart by applying an axial load. Although this procedure is the easiest to understand, the technical problems encountered during testing are numerous. Specimens cannot be readily fabricated into dumbbell-shaped specimen* like those customarily used for testing inetals. Cylindrical specimens cannot be loaded in jaw-clamps because adverse stress conditions arise at the clamping points, which causes unreliable results. An innovation developed by Niles Grosvenor at the Colorado School of Mines, in which the load is applied through steel-end caps glued to the ends of the specimens, has considerable merit, hut the samples are costly to prepare.2 All tests using a direct pull are further handicapped by the possibility of small amounts of bending being present, the specimen&apos;s surface condition, and

Jan 1, 1968

By J. D. Davis, A. C. Fieldner

The older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer,&apos; who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter"g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 1, 1925

Mark R. Lamb, Torres, Sonora, Mexico (communication to the Secretary*): I have read Mr. Merrill&apos;s paper with much interest, and cannot but accept his challenge as regards the cost of the clean-up at the Homestake mill. If I understand him correctly, the two men take the precipitates from the presses in about six hours, and do nothing towards refining them. If that is so, it would correspond to the work four men do here in about eight hours—that is, to clean the box and to place the precipitates in the driers. In order to make a fair comparison, the bullion in each case should be stated in ounces, since it is as diflicult to precipitate silver as gold, and our bullion is mostly silver. Bullion to the value of $50,000 is equivalent to a weight of about 2,500 oz. At our last clean-up eight standard bars, each 1,100 oz. in weight, were made, which equals a total weight of 8,800 oz&apos;. Four men had the precipitates drying by 8 p.m. This plant, the Minas Prietas works of Charles Butters & Co., at Minas Prietas, has square-bottomed electrolytic vats, an arrangement which necessitates the handling of all the precipitates in buckets. The Butters plant at Virginia City, Nev., is equipped with conical vats, and probably could make a still better showing under similar conditions. Another point is that common labor only is required. (Ordinary laborer&apos;s wages at Minas Prietas are $0.70 gold.) I may say also that, except for the convenience of the refinery, the box could be cleaned monthly, instead of bi-monthly, at only a slight additional expense. The comparison, if made a few months ago, would have been much more in favor of the electrolytic process, as the tailings handled at that time contained a large quantity of copper, and the amount of zinc-dust required would have been enormous.

Jan 1, 1904

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-&apos; ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration &apos;of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

By R. Ellerman

The hydrometallurgical processing of an impure zinc oxide fume is described. Flowsheet includes roasting for fluorine elimination and countercurrent leaching to produce a neutral sulphate solution. This solution is combined with zinc sulphide leach solution for subsequent purification and electrolysis. Novel to the neutral leach step is the use of automatic pH control. THE electrolytic zinc plant of the Hudson Bay Mining and Smelting Co. Ltd. was erected in 1929-1930 to process zinc sulphide concentrates produced from ore mined at Flin Flon, Manitoba. Since 1930, production of high purity slab zinc has been continuous. In May 1951, construction of a fuming plant was completed and operations were started to recover zinc from copper smelter reverberatory slag. A second zinc-bearing material in the form of an impure zinc oxide fume was then made available for treatment. Coincident with the construction of the fuming plant, additions were made to the electrolytic zinc plant to recover the zinc in the fume as slab metal. The original plant capacity of 70 tons of slab zinc per day was steadily increased up to May 1951, at which time the daily production averaged 130 tons. With the advent of the fuming plant and the processing of zinc oxide fume, production was stepped up to the present capacity of 190 tons per day. Of this, approximately 48 pct is contributed by the processing of zinc oxide fume. This additional source of raw material has allowed a 20 pct cutback in mining and milling operations, thereby adding considerably to the life of the Flin Flon mine. Zinc sulphide concentrates are treated by the usual hydrometallurgical method. Details of this operation and plant were described by Carr and Reikie in 1935&apos; and Kent in 1951.8 The impure fume is treated in two operations. First, it is roasted to eliminate fluorine. Next, it is subjected to a countercurrent leach with spent electrolyte to extract the zinc as a neutral zinc sulphate solution. During this leaching step, soluble impur-

Jan 1, 1956

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler&apos;s saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler&apos;s saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By Zay Jeffries

THE object of the present paper is to enlarge somewhat on the general principles advanced in my discussion 1 of Mathewson and Phillips&apos; article on. The Recrystallization of Cold-Worked Alpha Brass on Annealing.2 It will also serve as an acknowledgment of Prof. Howe&apos;s3 most important remarks on my contribution. In this paper the writer has adopted Prof. Howe&apos;s suggestion to substitute the term "germinative temperature" for "critical temperature for grain growth." Instead of being an exact or certain temperature it should be considered that the germinative temperature phenomenon exists throughout a small temperature range. Factors Influencing Fast Growth Phenomena The development of grains of macroscopic size at the germinative temperature should be considered the extreme condition of a general rule. When considered in this light it is not strange that the development of these large grains should be the exception and not the rule. The principal factors influencing the operation of the laws of fast growth temperature are as follows: 1. Rate of heating.

Jan 10, 1916

By C. W. Clark

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,1 written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world&apos;s larg-est producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a. commercial scale followed in October 1935. This paper will deal with selenium and tellurium produc-tion and also with present operations in the silver refinery. Blister cakes from Hudson&apos; Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te.

Jan 1, 1938

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,&apos; 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956

By Henry Howe

THE data which are collected in Table 1 show that the ferrite of low-carbon steel and of electrolytic iron, like the network of hypo- and hyper-eutectoid carbon steel, inherits, either absolutely or relatively, the, grain size of the mother austenite from which it is born in cooling through the transformation range. This evidence is so abundant and concordant as to cast doubt on Prof. Jeffries&apos; 1 hypothesis of what might be called reversed inheritance, by which he explains Mr. Ruder&apos;s observation2 that the grains of a "slug of pressed pure electrolytic iron powder"were coarser, perhaps 12,000,000µ2, after a 3-hr. exposure to 1000° C. than after a 3-hr. exposure to 1250-1300°, when they were about 35,000µs. His explanation implies a natural tendency of coarser austenite grains to yield finer ferrite ones than spring from finer austenite grains, so that the inheritance is reversed. What seems to me a simpler explanation is that the enormous grains which followed the 1000° heating were not inherited from the mother austenite, but were formed by the process of natal coarsening, by means of which Stead and Carpenter developed grains of this same order of magnitude in this same kind of material, on heating to 950° or to 1000°, the temperature used by Mr. Ruder, provided the exposure was not unduly prolonged, and it does not seem to have been in Mr. Ruder&apos;s case. That their coarsening was natal and not through inheritance is shown first by the fact that their grain coarseness was out of all proportion to their relatively low temperatures and short periods, and hence was very far in excess of the grain size which the mother austenite must have had, and second and more cogently by the fact that the shape of these coarsened grains was evidently determined by the temperature distribution which existed during and immediately after the Ar3 transformation, that during the passage from the gamma to the non-gamma state.

Jan 9, 1917

By John. C. Reed

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62° W. The average dip is about 67° SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30° W. and average dips about 75° SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30° for the south-west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By AIME AIME

CONCIDENT with what promises to be a record-breaking year of activity in the world&apos;s greatest iron-ore district is the announcement of plans to hold the regional meeting of the American Institute of Mining & Metallurgical Engineers at Duluth, Aug. 12 to 15 in¬clusive. More than 25 open-pit mines will be in operation in Minnesota&apos;s great iron-ore district this year, affording to those attending the convention an unusual op¬portunity of viewing practically side by side the interesting activities of power-shovel operations, railway haulage, truck haulage, conveyor-belt haulage, tower-excavator operations, iron-ore concentration, and underground mining. The ore can be followed from the mines to washing and concentrating plants and to the docks and lake carriers on Lake Superior, where an average of one boat of 10,000 tons&apos; capacity will be loaded and depart every 15 minutes, day and night, during the 1941 shipping season.

Jan 1, 1941

By L. H Levenson, Charles S. Barrett

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.&apos; Various methods involving etch pits have been used by other investigators. Bridgman&apos;s method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm&apos;s length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By Charles S. Barrett, L. H. Levenson

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.&apos; Various methods involving etch pits have been used by other investigators. Bridgman&apos;s method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm&apos;s length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By V. T. Stringfield, H. H. Cooper

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson&apos; who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson&apos;s knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida. More recent reports give the results of investigations that have been in progress in cooperation between the Florida Geological Survey and the U. S. Geological Survey since 1930. As a result, the ground-water geology and hydrology of Florida are now so well known that ground-water problems such as confronted early investigators no longer exist. However, new problems arise and new discoveries are made as the demand for more ground water increases with the development of the State. Water-Bearing Formations Descriptions of the geologic formations and a map showing their distribution at the surface are given in a recent report by Cooke.&apos; The geologic formations that yield the ground-water supplies in Florida represent only a small part (about 1000 ft) of the total thickness of the sedimentary rocks (more than 15,000 ft) that underlie Florida. The water-bearing rocks that yield fresh water include more than two dozen formations that range in age from Eocene to recent. The Eocene formations, which consist chiefly of limestone, are the oldest and the deepest of the formations in Florida that yield fresh water to wells. In 1944, on the basis of a study of the foraminifera, the Applins -ivided the limestone of Eocene age into six formations, which are as follows, from top to bottom: Age or group Formation Jackson Ocala limestone icAvon Park limestone Claiborne -j Tallahassee limestone aLake City limestone Wilcox Salt Mountain limestone xOldsmar limestone The Ocala limestone and the underlying formations of Claiborne age, along with some of the overlying limestone of Oligocene and Miocene age, constitute the principal source of water in Florida and southeastern Georgia and generally may be regarded as forming one artesian aquifer or water-bearing unit. This aquifer is referred to in this paper as the Floridan aquifer, a name proposed by Parker.&apos; In part of Seminole County alone more than 1000 flowing wells yield water from the Floridan aquifer. A yield of 6500 gpm, or about 9.5 million gal per day, by natural flow from a well penetrating the aquifer at Jacksonville, Florida, was observed in 1942. A yield of about 7000 gpm by natural flow was reported for a well 1390 ft deep at St. Augustine in 1887. The largest yield reported from a pumped well penetrating the aquifer is 7500 gpm, or about 10.5 million gal per day. The aquifer is also the source of some of the large springs, such as Silver Springs, whose discharge, according to measurements made by the U. S. Geological Survey, has ranged from 526 to 1350 sec-ft, or from 340 to 872 million gal per day. The top of the Ocala limestone, as represented by contours in Fig. 1, indicates in a general way the geologic structure of the formations that comprise the Floridan aquifer. The Ocala is at or near the surface in the areas represented by shading in the northwestern part of the peninsula and also in an area in western Florida adjacent to Alabama and

Jan 1, 1952