Search Documents

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By David R. Mitchell, E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of fine sizes of bituminous coal. Approximately 18,000,000 tons of bituminous coal was cleaned by air machines in 1947, but such machines have not yet been applied in the cleaning of anthracite. This chapter is limited to a description of the processes in which the separation between coal and refuse depends mainly on a difference in specific gravity. Dry processes depending on differences in coefficient of friction, shape, or other property, are described in chapter 17. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. Some of these early machines are described by Berrisford,1 Chapman and Mott,2 and Mitchell.3 Only two machines are extensively used today in the United States, the Stump air-flow jig and the American oscillating table. GENERAL CHARACTERISTICS OF AIR CLEANING MACHINES The principles of gravity concentration and the properties of air as a medium for separation were explained in chapter 9. It was pointed out that because of the low density of air a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. It was also noted that the compressibility of the air may cause "geysering" of the bed and disturbance of the hindered-settling classification if the correct balance of conditions is not maintained. Most devices use a vertical upward current of air through the bed of material. They differ by the method of imparting mobility to the bed and the method of removing the refuse. In general terms, the air machines can be divided into three types: 1. Pneumatic jigs where the air current is pulsated. 2. Pneumatic tables where the refuse is diverted from the direction of flow of the clean coal by a system of riffles fixed to the deck.

Jan 1, 1950

By F. Julius Fohs

A comparative balance sheet for 1924 and 1925 follows: 1925 1924 Barrels Barrels Gross production..................................... 763,000,000 714,000,000 Imports of crude oil.................................. 62,005,000 77,776,000 Imports of refined oil................................. 16,263,000 16,470,000 Total......................................... 841,268,000 808,246,000 Surplus supply....................................... 25,000,000 30,246,000 Indicated domestic demand........................... 704,465,000 667,000,000 Exports crude oil.................................... 13,353,000 17,913,000 Exports of refined oil................................. 98,450,000 93,087,000 Total......................................... 816,268,000 778,000,000 Stocks, Dec. 31 (crude 410,654,000).................... 538,000,000 513,000,000 These figures show an increase of 49,000,000 bbl. in production and little change in oil imported; 37,000,000 bbl. greater apparent domestic consumption and actually greater utility in consumption, due to increased gasoline production by cracking; and 1,000,000 bbl. more crude and refined oil exported in 1925 than 1924, representing a total apparent increased demand of 38,000,000 bbl. The excess of demand over supply in 1925 was 25,000,000 bbl. The increase of stocks over those at the close of 1924 was 25,000,000 bbl. Of the stocks on hand at the close of 1925, about 82,000,000 bbl. in California were not refinable. Imports from Mexico and South America It would not be surprising if, by 1930, we should actually welcome the imports from Mexico, Venezuela, Colombia, Peru, Argentina and Trinidad. If these States produce 155,000,000 bbl. and use, perhaps, 30,000,-

Jan 1, 1927

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By Frank Hultgren

The influence of grain boundaries and polygonized subsructure on the flow stress of commercially pure aluminum has hem studied. A systematic inz-estigoti017 of grain size and subgrain size and mis-orientation was pursued; the contributions of pain boundary md substruture hardening were found to he additive fuiictions. Subgrain boundaries exert greater influence on hardening at room temperature than do grain boundnries. Both subgrain diameter and misorientation influence flow stress, but only to the extent that both contribute to the dislocation density. The flow stress due to substructure may he described by the equation of = abp1/2. THE origin of substructure hardening in metals has remained unclear for a long time. Lately, both theory and experimental techniques have become more exact and merit a closer examination of the subject. In the present work, the influence of polygonized substructure size and misorientation in commercially pure aluminum on mechanical properties has been systematically investigated. The influence of substructure on mechanical properties has been compared with that of grain boundaries. In addition, the works of several authors are compared with theoretical predictions of substructure hardening. EXPERIMENTAL TECHNIQUES Aluminum of 99.9 pet purity (0.04 Fe, 0.046 Si, 0.00 Cu) was employed. Various grain sizes were produced by heavy (over 90 pet reduction in area) cold drawing and recrystallization at various temperatures. A (111) fiber texture was observed in all specimens. Grain sizes were analyzed statistically. Substructure of varying size and misorientation was produced by prestraining specimens of various recrystallized grain sizes. Specimens for mechanical testing and substructure analysis were recrystallized, prestrained, and annealed together. The samples were prestrained from 5 to 25 pet in tension at room temperature and annealed at 200" to 370°C for 2 hr. All samples were rapidly cooled (in air) from the anneal to retain the subgrain wall structure developed at the annealing temperature. A clearly polygonized substructure was developed in all cases. Substructure size was measured by the Berg-~arrett' technique and analyzed statistically. Substructure misorientation was measured in the following manner. Individual grains in the polycrys-talline aggregate were isolated and their intensity distributions mapped using an X-ray goniometer and Geiger counter. From the observed profiles, the

Jan 1, 1964

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.'" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.'-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet's solution.' Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By J. Wade Watkins, E. S. Mardock

The accurate evaluation of reservoir-performance characteristics in the secondary recovery of petroleum by water flooding requires use of a water tracer that may be injected into water-input wells and detected at oil-production wells to supplement data obtained from core analyses, wellhead tests, and subsurface measurements. Radioactive iodine has been used successfully as a water tracer in field tests to determine: (I) relative rates and patterns of flow of injected water between water-input and oil-production wells and (2) zones of excessive water entry into oil-production wells. Laboratory evaluations of potential water tracers, previous tracer studies, the value of using a radioactive tracer, general field procedures, and the use of surface and subsurface instruments for the detection of the emitted gamma radiation, are summarized. Data from the field tests are presented graphically and discussed in detail. It is concluded that the radioactive-tracer method, using radioactive iodine, may be used successfully to measure either the relative rates and patterns of flow or zones of excessive water entry into wells under conditions of comparatively rapid transit time between wells. INTRODUCTION Extensive use is made of data obtained from core analyses, wellhead tests, fluid characteristics, and subsurface measurements in evaluating the sweep efficiency of water injected into oil sands for the recovery of oil. Theoretical flow rates and patterns may be calculated from those data using radial-flow formulas, if it is assumed that the physical conditions in the productive formation are homogeneous. Unfortunately, homogeneous conditions rarely, if ever, exist in oil-productive formations. The use of a tracer that may be injected into an oil sand and detected quantitatively, or even qualitatively, at offsetting oil-production wells provides basic data that may be used in determining more accurately the subsurface rates and patterns of flow of injected water between wells than is possible by theoretical calculations based on assumed conditions. Consideration of the data obtained by using a water tracer assists in the application of remedial measures to water-input wells, such as plugging of channels, or selective plugging of highly permeable zones, thereby effecting a more uniform flood and a greater ultimate oil recovery. A water tracer should have the following characteristics: (1) low adsorption on solid reservoir material; (2) high solubility in water; (3) low or negligible solubility in crude petroleum; (4) a wide range of solubility of compounds that may be formed by chemical reactions with ions present in reservoir rocks or waters; (5) high detectability in low concentrations by portable apparatus; and (6) general availability at low cost. Additional desirable characteristics are that the tracer should be nonhazardous in nature under normal working conditions and quantitatively detectable in the well bore, as well as at the surface. Review of Previous Tracer Studies The need for a water tracer has been recognized for many years. As far back as 1906, Dole1 described the use of fluorescein in flow-rate studies made in France in 1901. In 1921, Ambrose" discussed in detail the use of organic and inorganic dyes, chlorides, nitrates, and other anions, lithium salts, and the Slichter electrical

Jan 1, 1955

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

HE high vapor pressures of metals such as lead, calcium, lithium, bismuth, and magnesium at steel-making temperatures present experimental problems which have thus far rendered it almost impossible to obtain really reliable data for their solubilities in liquid iron. Many investigators have attempted to equilibrate liquid iron in the same crucible with the undissolved liquid phase of such volatile metals. The published results,l-6 although useful, are often questionable on the grounds of not being obtained under true equilibrium conditions. Such information is not always of practical value in any case since the equilibrium vapor pressure is often several atmospheres and steel is not currently made at these pressures. Solubility measurements at lower partial pressures (< 1 atm) appeared to be more practical and easier to make. These data could be used to calculate solubilities at other pressures where Henry&apos;s Law is obeyed, and to estimate solubilities under other conditions of temperature and pressure with useful accuracy. This note outlines the development of a general technique for the measurement of solubilities in systems of this kind. The method involves equilibration of the high-boiling metal at known temperatures with the vapors of a low-boiling metal at known partial pressures. Analyses of quenched samples provide vapor pressure-solubility data and make calculations of alloy thermodynamics possible. The principle involved is similar to the closed-system diffusion-transport method which is difficult to apply with most high-melting liquid metals like iron, due to closure problems. A two-zone horizontal (molybdenum wire element) tube furnace, Fig. 1, provides two constant-temperature zones in a reaction tuve (3/4 in. ID by 1 in. OD by 36 in.). A high-boiling metal sample, 9, introduced in the higher-temperature zone, is maintained at temperature T1, and a volatile metal sample, 7, in the lower-temperature zone, is held at T2. A stream of argon with 10 pct hydrogen is passed via flowmeters, 1, and mixing-drying towers, 2 and 3. through the reaction tube at a favorable flowrate and acts as a carrier gas which entrains vapor from the volatile liquid metal at a specific constant partial pressure. The gas mixture passes through a system of constrictions, 6 and 8, to the higher-temperature zone, establishes intimate contact with the high-boiling liquid sample, 9, and exits through a small condenser tube. The entire system is at (nearly) atmospheric pressure and the volume of carrier gas passed is measured with a wet gas meter. When the high-boiling sample attains equilibrium with the vapor phase, both samples are removed and quenched. Analysis of the high-boiling sample for solute content reveals its solubility for the low-boiling metal at a vapor pressure calculated from carrier-gas volume and either a) weight loss of volatile metal or 6) weight gain of high-boiling sample plus condenser (which collects the undissolved vapors). To test the capabilities of the method, liquid silver at 1403&apos;C was equilibrated with lead vapor at various partial pressures. The relatively simple Pb-Ag system was particularly suitable for uncovering experimental problems and providing the first step toward investigations with more volatile metals and more difficult combinations.

Jan 1, 1965

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson&apos; measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans&apos; and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner&apos;s data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

By H. E. Rorschach

Activity in Oklahoma oil fields made 1937 one of the best years since 1926. During the year, 3454 wells were completed, an increase of about 25 per cent over the year 1936. Purchasers reports filed with the Corporation Commission of the State of Oklahoma showed a total of 221,842,-788 bbl. of oil purchased from leases in 1937, an increase of about 10 per cent over 1936. The assembly of a complete table of all of the oil fields in Oklahoma has not yet been achieved. Many of the early records of operators and pipe-line companies are incomplete. Table 1 includes all of the new fields, and this year there has been added work done covering pools discovered in previous years, so that most of the important fields in the state of Oklahoma are included therein. The outstanding development of the year was the discovery of the producing horizon classified as the Wilcox in western Payne County by the Mid-Continent Petroleum Corporation on a unitized block in sec. 18, Tp. 18 N., R. 2 E. This block is operated hy the Mid-Continent and owned in conjunction with the Carter Oil Co., Transwestern Oil Co. and Sinclair-Prairie Oil Co. Another important development of the year was the extension of the deep zone in the old Fox-Milroy area of Carter and Stephens Counties. Some of the other discoveries made during the year 1937 are South Cromwell, discovered by Sinclair-Prairie Oil Co.; Cromwell extension of the Fitts pool in Pontotoc County; discovery of the Langston area in Logan County; discovery of the Sporn area in Lincoln County by Skelly Oil Co. and the discovery of the North Wellston area in Lincoln County by Standard Oil & Gas Co. Table 2 shows the new oil areas discovered in Oklahoma during the year 1937 and areas that were discovered in 1936 but developed in 1937. Fox-Milroy Area.—Three wells were completed to the deep producing zone during the year. One of the wells completed in the early part of the year uas the Carter Oil Company&apos;s No. 1 Harley in sec. 24, Tp. 2 S., R. 4 W., 3 1/2 miles northwest of the original discovery well, the Ruth

Jan 1, 1938

By D. F. Hewett

ALTHOUGH most persons will agree that an individual or a nation can profit from the experience of other individuals or nations, there is always room for debate over the degree of similarity of their past and present conditions and of their future problems. Noting the increasing interest that Americans are showing in our mineral problems, I have felt that we could profit from reviews of the experiences in mineral exploitation acquired by the industrial nations of Europe. Whether we can learn much from Europe&apos;s experience in exploiting such minerals as petroleum may be debatable, but certainly, with a record of metal production extending back nearly 3000 years, Europe should hold much of value for America. A trip to Europe in 1926 permitted me to visit 28 mining districts, of which about half are now or have been in times past outstanding sources of several metals. The districts range from England to Greece and from Spain to Poland. To summarize briefly my impressions of these mining districts, as well as such reactions to the thought and life of Europe as so short a visit permits, I shall only venture the opinion that Americans can review with great profit the ideas and actions of Europeans, with regard not only to the production of metals but to many expressions of life. I believe that America has made and is making new contributions to the art of living, as well as to the arts of mining and metallurgy, but in so far as Europe is and has been a laboratory of economic, social and political experiments, the results she has attained deserve the thoughtful attention of America. I have come to believe that many of the problems that harass Europe lie in our path not far ahead. I have therefore hoped that a review of metal production in Europe in the light of its geologic, economic and political background may serve to clear our vision with regard to our own metal production. One can not examine the literature of national metal production without being impressed that the countries of continental Europe, especially Germany and Austria, have shown greater interest and devoted more time to research into the record of metal production than Great

Jan 1, 1929

By Charles A. Stickels, Edward E. Hucke

The dihedral angle, formed by the intersection of three interfaces, is often determined by measuring a sample of apparent angles of intersection seen on a random plane of polish, then comparing the exerimental distribution of angles to the distribution calculated by Harker and Parker. Statistical tests show that the latter distribution does not satisfactorily describe the population from which samples are drawn. It is concluded that the major reason for this discrepancy is the presence of a range of dihedral angles in all specimens. When reasonable care is used experimentally, random measuring error is unimportant. It is shown that measurements made on dispersed second-phase inclusions are subject to a systematic error depending on inclusion size, which can be minimized by using adequate magnification. A dihedral angle, calculated from a sample of observed angles as though a unique dihedral angle were present, is termed an "effective dihedral angle". Experience has shown that "effective dihedral angles&apos;&apos; are reproducible quantities, useful for characterizing samples. Methods of determining an "effective dihedral angle", establishing its reliability, and making comparisons between samples are discussed. THE authors have recently reported measurements of the dihedral angle formed by liquid-lead inclusions lying in nickel grain boundaries.&apos; Di- hedral angles were measured by the statistical method first employed by Harker and parker2 and used subsequently by many other workers.3"8 Since a relatively high degree of accuracy was necessary in the authors&apos; experiments, the reliability of this method of dihedral-angle measurement was examined. Briefly, this method of measuring dihedral angles is usually performed as follows. A multiphase alloy is prepared, equilibrated under conditions which allow sufficient interface mobility to establish equilibrium, quenched to room temperature, then prepared for metallographic examination. A large number of observed angles, formed by the traces of grain boundaries and/or interphase boundaries on the plane of polish, are measured at high magnification. If all orientations of interfaces in the specimen are equally probable, Harker and parker2 showed that the population of observed angles is described by a distribution function containing a single parameter, the dihedral angle, 8. certain properties of the population, e.g., the mode or median, have been calculated from this distribution function in terms of the dihedral angle.3, 9 Thus, if the mode or median of a sample is identified with the corresponding property of the population, a unique value for the dihedral angle is determined. One defect in this procedure lies in identifying the properties of a sample of observed angles with the properties of the population from which they are drawn. If one were to proceed in a more rigorous fashion, it would be necessary to find a function of sample properties which is an estimator of the dihedral angle. Then by determining the distribution function for the estimator one could set limits on the value of the dihedral angle. The most apparent obstacle to this straightforward approach is the complexity of the distribution function assumed to describe the population. In analytical form, the distribution function may be written:2, 10

Jan 1, 1964

By N. H. Fisher

Geographical Distribution &apos;he most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig I). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation Ltd., of Melbourne, on Stradbroke Island, and in other places. Physiography Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 56 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, upto 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1949

By Dewey J. Sabin

THE Rio de Canada Honda placer property is situated at an altitude of 5500 ft. above sea level in the San Luis Mountains of the Province of San Luis, Argentina. The mine is reached by 70 km. of fair truck road, from the nearest railway station on the Ferrocarril Buenos Aires al Pacifico. The Pan-American airport at Villa Mercedes, 1.40 km. distant, serves as the most convenient point for shipment of gold. Placer mining in the Rio de Canada Honda dates from the time of the Incas and the present native population depends on the gold washed from this river and the adjacent arroyos as a means of livelihood as did the many generations before them. They dig pits to bedrock where they are not driven out by water, and mine the bedrock gravel by means of tunnels and caves. No timber is available and the ground is supported by rock cribs carefully built with the boulders encountered; or with angular blocks of slate rock taken from quarries on the surface.

Jan 1, 1936

By W. A. Straw

IN the manufacture of telephone apparatus a number of nonferrous sheet metals are blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming, characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper.

Jan 1, 1931