Search Documents

By J. A. Hutcheson

NO one questions that it is technically possible to achieve the controlled release of atomic energy in a form that can be converted into heat or electricity. However, before this is actually an accomplished fact a great amount of work must .be done. This work falls into two general classifications: research and engineering development. At present a research program is under way in this country, co-ordinated and directed by the Atomic Energy Commission, which, as time goes on, will uncover fundamental knowledge of this new science that is essential before industrial applications of atomic energy are practical. Undoubtedly therefore, as the store of available knowledge increases, a time will come when answers to the many questions relating to practicality of atomic energy in industry can be determined with reasonable certainty. That the application of atomic energy in industry will eventually be proved practical is assumed. What then are the engineering problems that must be solved before the first practical electric power generating station can be built?

Jan 1, 1948

By V. W. Bihlman, H. M. Williams

In the construction of internal-combustion engines, the cooling of the combustion chamber and pistons is of great importance. In certain types of engines, the adequate dissipation of heat from the bearings is also important. One of the important factors affecting heat dissipation from these parts is the thermal conductivity of the material used. A search of the technical literature shows that, in general, the thermal conductivity of the elements1 has been determined accurately by a number of investigators. The data on the industrial alloys are, however, meager. For an investigation of these alloys, the thermal-conductivity apparatus described in this paper has been constructed at the laboratory of the General Motors Research Corporation. It is desirable that an apparatus for work of this nature should give fair accuracy of results with a convenient form of specimen and a reasonable rapidity of operation. A summary of the different methods of determining thermal conductivity is given in the first volume of the " Dictionary of Applied Physics," pages 429 and 470. The method selected as best satisfying these conditions is that of Griffith, on page 443, with the addition of a guard ring similar in principle to the method used by Berget (P. 445). Briefly, the method consists of heating one end of a bar T, Fig. 1, electrically, measuring the amount of heat transmitted through the bar by a flow calorimeter J fastened to the other end, and measuring the temperature gradient along the bar. To compensate for the loss of heat laterally, the test bar is surrounded by a guard ring E, in the form of a steel pipe, which is electrically heated at the bottom and cooled at the top with a

Jan 1, 1923

By V. W. Bihlman, H. M. Williams

In the construction of internal-combustion engines, the cooling of the combustion chamber and pistons is of great importance. In certain types of engines, the adequate dissipation of heat from the bearings is also important. One of the important factors affecting heat dissipation from these parts is the thermal conductivity of the material used. A search of the technical literature shows that, in general, the thermal conductivity of the elements1 has been determined accurately by a number of investigators. The data on the industrial alloys are, however, meager. For an investigation of these alloys, the thermal-conductivity apparatus described in this paper has been constructed at the laboratory of the General Motors Research Corporation. It is desirable that an apparatus for work of this nature should give fair accuracy of results with a convenient form of specimen and a reasonable rapidity of operation. A summary of the different methods of determining thermal conductivity is given in the first volume of the " Dictionary of Applied Physics," pages 429 and 470. The method selected as best satisfying these conditions is that of Griffith, on page 443, with the addition of a guard ring similar in principle to the method used by Berget (P. 445). Briefly, the method consists of heating one end of a bar T, Fig. 1, electrically, measuring the amount of heat transmitted through the bar by a flow calorimeter J fastened to the other end, and measuring the temperature gradient along the bar. To compensate for the loss of heat laterally, the test bar is surrounded by a guard ring E, in the form of a steel pipe, which is electrically heated at the bottom and cooled at the top with a

Jan 1, 1923

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland' found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.' determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-' torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.' These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren' and Miller' were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy). Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

By Eugene C. Robertson

INTRODUCTION A direct proportionality between the observed displacement of a fault and its thickness of breccia and gouge has been proposed recently (Robertson, in press). To validate this finding, an explanation of the mechanics of continuous breccia formation is needed and is offered in this paper. A summary of evidence for the finding will show why an explanation is needed. The correlation between fault displacement [d] and accompanying breccia- plus-gouge thickness [t] seems to be linear and reasonably well established over 6 orders of magnitude, with a range in [d] from 1 mm to 1 km, on a trend of [d/t]= 100, shown in Figure 1. Most of the points are for faults observed underground in mines. The [d] – [t] relation is limited to normal and reverse faults, that have a flat to steep dip and a displacement less than 5 km. It is not applied to large strike-slip and low-angle overthrust faults, whose displacements and breccia thicknesses are widely variable and uncertain. Undisplaced jointed rock is not included in the thickness measurement. A complete description of sources and analysis of the data is given in Robertson (in press). One would intuitively expect that continued movement on a fault would grind up the previously formed breccia and gouge and not produce any more, but the evidence (Fig. 1) indicates otherwise. A physical model to explain continuous formation of gouge and breccia from the wall rocks can be obtained from laboratory experiments on friction.

Jan 1, 1982

By Edward Martinez

The reactions occurring in the copper segregation process were studied by heating mixtures of chryso-colla, salt, and a reducing agent. The techniques used in this investigation were differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). The initial chloridizing of the oxide copper occurs below 500°C and cupric chloride may be the compound formed. Volatilization and reduction of the copper chloride take place above 550°C, although these reactions do occur to some extent below 550°C. A difference in the distribution of the metallic copper in the reducing agent was found when sodium chloride was used compared to magnesium or calcium chloride. Segregation was obtained with mixtures of cupric oxide, salt, and charcoal with no quartz or silicate present. Preliminary tests indicate that segregation may occur even in the absence of water vapor. The DTA and TGA techniques were found to be of great value in studying these reactions. The copper segregation process is a method for treating oxide copper ores. The ore is heated, most commonly in a kiln, with a reducing agent and a halide salt, generally sodium chloride, to approximately 700°-750°C and held for 30 to 60 min. The addition of the salt results in the migration and reduction of the oxide copper to metallic copper on the surface of the reducing agent rather than in the original mineral structure. The metallic copper can then be recovered by a subsequent leaching or flotation step.1-4 Experimental work in 1923 on oxide copper ores from the Sagasca mines in Chile led to the discovery of the reduction process. It was found that during the reduction of the copper mineral with coal, at about 700°C, the copper migrated to the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge. The ratio of salt to reducing agent may vary somewhat, but in general 0.5% to 1.5% sodium chloride and 0.5% to 1.0% coal or coke have been mixed with the ore. Less than stoichiometric amounts of salt are required to convert all the oxide copper to a chloride, so that a cycle of reactions appears to be occurring. Several investigations reported in the literature have proposed reactions to explain the mechanism of the process.5-10 There appears to be general agreement that water is necessary for the reactions to occur; that once the sodium chloride reacts with silica or silicates in the ore, the hydrochloric acid formed will convert the cupric oxide in the mineral structure to cuprous chloride. However, there appears to be a conflict of opinion on the reactions involved in the reduction of the cuprous chloride to metallic copper on the surface of the carbon. Rey has indicated that salt, water vapor, and

Jan 1, 1968

By Philip Davidson, Wm. B. Price

The object of this paper is to present, a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350" C. throughout the coininercial annealing range.. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: Alloy Copper, Lead. Iron. Nickel, ManGanese, Zinc, PeR Cent. Per Cent. Per Cent. Per Cent. Per Cent. PEr Cent. A................ 64.68 Trace 0.194 6.73 0.06 remainder B................ 65.82 1.27 0.227 6.17 0.06 remainder C................ 65.44 Trace 0.345 17.83 0.08 remainder D................ 65.60 1.08 0.238 17.77 0.06 remainder These alloys were lolled in accordance with regular mill practice to approximately No. 6 R. & 6. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 1/2 in. long by 1/2 in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 235 in. were also taken.

Jan 1, 1921

By S. R. Zimmerley, John Gross

The method of measurement of surface on quartz particles was given in a previous paper.' With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. The Crushing Device The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1 in. dia. by 36 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 1/2-in. dia. by % in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of -the chamber. The mortar rests on a solid steel base B but is separated therefrom

Jan 1, 1930

By C. E. Turner, J. R. Elenbaas, R. D. Grimm, J. A. Vary, D. L. Katz

A technique is presented by which well samples and core plugs of dolomite formations are classified by microscopic examination into seven different porosity grades. Quantitative values of porosity and permeability are determined for each grade by a statistical correlation of the core plug test data with the porosity grading system. These quantitative values are applied directly to the grades exhibited in the well samples for the purpose of estimating the reservoir void space for wells that were not cored. The procedure is described for estimating the gas reserves per unit area lor the South Hugoton gas field. but a reserve estimate for the field is not given. INTRODUCTION The miscroscopic examination of well sample; and the graphic recording of their lithologic qualities and other distinguishing characteristics of various geologic formations drilled is both a science and an art of long standing and wide application. Usually the primary objective of a geologist who "sits on the well" and examines the samples are: to identify the formation being drilled, determine the total depth, casing point. and completion interval. In most cases the porosity is described. if done at all, in general terms. such as: trace, scattered, fine, poor, fair, medium. good, excellent, or in some other relative terms. In fields where various geologists have examined samples and recorded observations on many wells considerable variations in lithologic terms and porosity descriptions occur unless there is primary effort to establish uniformity of logging observations and standards of recording observable porosity. When an estimate of the pore volume of a reservoir is made a geologic concept of the processes that control the magnitudes of porosity and permeability is developed by microscopic examination of well samples. The characeristics and appearances are then mentally related to rather general quantitative units of porosity based on physical core data from the same reservoir or on such data or experience in other reservoirs that have similar qualities. The reliability of such estimates depends largely on the variations of the lithology of the formations, the geometric properties of its void system. the extent of comparisons of sample appearances with porosity data, as well as the uniform recording of all relevant characteristics. This statement is particularly significant for dolo-mitized limestone formations of substantial thicknesses and heterogeneity such as the Permian Dolomites of the Hugoton gas field. Jn this field, as well as in most of the Permian Dolomite fields, the producing formations are of relatively great thicknesses in which the porosity and permeability of the reservoir varies substantially in all directions, depending on the crystalline structure. degree and kind of impurities, kind of fossils anti cementation thereof, degree of dissolution. and fracturing. The variations of the lithologic texture of the dolomites and post deposition alterations have resulted in porosities and permeabilities of such magnitudes that only a part of the gross thickness can be counted as "pay." At the time of this study insufficient gas production had been experienced to apply the pressure decline production method in the South Hugoton Field and the electric logs are not definitive enough. The problem of estimating gas reserves in the south part of the Hugoton Field is primarily one of determining the pay thickness and porosity from well samples and core data. The area studied embraced all that part of the field lying south of an east-west line through Guvmon, Okla., anti containing approximately 1.000,000 acres. This paper describes a technique of correlation of physical core data with well samples so that quantitative values of pay thickness, porosity. Permeability, and connate water may be assigned to well samples that are representative of a given interval, and thereby permitting the estimation of gas reserves lor a given unit area. The procedure was developed by a uniform microscopic qualitative porosity grading of the dolo. mite core plugs.. and relating these grades to the respective physical core data on a statistical basis The well sample-were also graded in a Similar manner in order that the quantitative values established lor the core plugs could be applied to the well Sample for wells that were not cored. GRADING OF DOLOMITE A group of experienced geologists was given the assignment of examining the samples on all wells in South Hugoton in order that they could log their observations in a uniform and standardized manner and grade the observed porosity so that it could be related quantitatively to the core data. The group initiated the study 011 chips from cores which bad been tested for porosity and permeability. This study continued until all of the geologists developed a common knowledge of lithologic terms and of the characteristic appearances of the samples and their relations to measured porosity. The characteristic appearances of the dolomite samples under twelve-power magnification as related to their qualitative porosities afforded a classification of the dolomite into :even grades of porosity, ranging from dolomite of no-visible porosity under twelve-power magnification to dolomite of excellent porosity. The assigned grade for a specific 10-ft interval is a weighted average of all visible grades of porosity exhibited by the cuttings representing that interval. The porosity characteristics were recorded by a color graph adjacent to the lithology column in conjunction with a numerical system for further definition of relative porosity as shown in Fig. 1. The three vertical lines to the right of the lithology column each represent 33 1/3 per cent. which lines were used to record the percentage of the samples, for any particular interval. that showed porosity under the microscope. The colors were used to denote actual pore size. i.e., orange. blue and I-ed for pore diameter of one-fourth or less. one-fourth to one-Ilalf. and greater than one-half millimeter, respectively. The area colored 1)). one or more colors represents the percentages of the samples exhibiting pores of the respective size or sizes. The numerals from one to six inclusive shown on the log in

Jan 1, 1952

By Robert W. Hunt

THE first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 72 inches diameter; eight inlet and eight outlet valves of 22 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington's proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 36g inches diameter, by 36-inch stroke, with water-plungers of 91 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steam-cylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced

Jan 1, 1876

By John D. Price

COAL blending, in the preparation of coal before coke making, is so commonly practiced as to be almost universal. But the reasons underlying this practice, the benefits resulting from it, and the materials used in blending vary widely. This paper will outline the various phases of the subject and present information which may be correlated with work that has been done elsewhere. It will deal entirely with work done on the high-volatile coking coals of the western part of the United States, special emphasis being given to the coals of Colorado and Utah. A surveyL of the 86 coke plants in active operation in the United States during 1949 indicates that only 9 plants, or 10.5 pct of the total, charged one single rank of coal into their ovens, while the remaining 89.5 pcl made use of blending in some form. This report indicated that of these total plants 5 used straight high-volatile coal, 4 used straight medium-volatile coal, 47 used blends of high and low-vola-tile coals, 25 used blends of high, medium, and low-volatile coals, 2 used blends of high and medium-volatile coals, 3 used blends of medium and low-volatile coals. The fact that certain plants operated on a single kind of coal should not be interpreted to mean that no blending was practiced there, for invariably such plants secure their coal from more than one source and in the interest of uniformity do blend the coals as received. The general term coal blending covers two fields, the first of which is the mechanical mixing of a number of coals to secure uniformity. Often it is found necessary to secure coal for coke production from a number of different mines; these coals, though of the same general type or rank, may differ in their chemical composition or in the physical qualities they impart to coke made from them. Again, it is not unusual to find that coal from different sections of the same mine may show variations in quality. Under such conditions it may be necessary, in the interest of a uniform final product, to introduce a system of blending bins, a bedding yard, or other mechanical methods of securing a uniform mixture. Unfortunately this form of blending has received very little attention up to the present time; it has not received the consideration its value merits. The second type of blending, while also for the purpose of coke improvement, deals more particularly with the use of a blending agent differing in character from the base coal: it is this form of blending that will be discussed here. To consider only the western coals, for blending may be found necessary for other reasons with other coals, blending has been practiced experimentally or commercially under the following conditions: 1—When a single coal or mixture of coals of the same rank does not produce a satisfactory coke. For example, a high-volatile coal when used alone is likely to contract when coked so that a comparatively weak coke is formed. Or, if of very low rank, the coal may be deficient in the necessary bitumens required for good coke production. 2—When a product of some special quality is required, for example, when a plant ordinarily producing blast furnace coke must operate at slow coking rate to produce a high-grade foundry coke. Under this condition the reduced daily production of all products which accompanies slow coking time may be undesirable, and the use of some blending agent to increase the size of coke made at faster coking rates may be necessary. 3—When greater yield of coke or its coproducts is needed. Depending upon economic values of the products it may be found desirable to increase the yield of one or the other. 4—When supply of a particular coal must be used, either to protect reserves of high quality coking coal or to utilize a surplus or inferior product not otherwise usable. Many materials have been used for blending purposes, the exact agent to be used depending both upon the condition to be corrected and the nature of the base coal. No universal blending agent that can

Jan 1, 1954

By Roshan B. Bhappu, Ronald J. Roman, Dexter H. Reynolds

The reaction between manganese dioxide and molybdenite in a water- sulfuric acid medium was studied at atmospheric pressure and from 25° to 103°C. Both solids are dissolved to give, as final products in solution, Mo(VI), S(VI), and Mn(II). Stoichiornetric relationshifis are most simply represented by the equation MoSz + YMnO2 + 15H+ - HMoO-4 + 2HSO-4 + 9Mn++ + 6H20 The rate of this reaction was found to be dependent on temperature, manganese sulfate concentration, acid concentration, and, in a complex way, the surface areas of both manganese dioxide and molybdenite. Both the total amount of manganese dioxide and tnolybdenite and the ratio of manganese dioxide to molybdenite played a part in determining the over-all rate of the reaction. The effect of acid concentration on the rate was also dependent on the ratio of manganese dioxide to molybdenite. SEVERAL reports in the literature describe reactions using manganese dioxide in water-sulfuric acid media as an oxidizing agent. Nearly all previous work describes interactions between an ion and manganese dioxide, such as the oxidation of ferrous to ferric iron,' or the interaction between a molecule in solution and manganese dioxide, such as the oxidation of toluene to benzaldehyde.2 Only a few references describe the use of solid manganese dioxide to oxidize another solid in sulfuric acid. One report3 states, "Manganese dioxide in dilute sulfuric acid solutions had no beneficial effect (in leaching copper from chalcopyrite), but in more concentrated acid solutions the rate of solution was about the same as that for permanganate." In 1902 a German patent4 described a process which used manganese dioxide in strong (50°Be') sulfuric acid for oxidizing chromite ores to soluble iron and chromium salts. The process consisted of mixing the sulfuric acid with the finely ground ore and manganese dioxide. The pulp was then heated to about 120°C and an electric current passed through it. The manganese dioxide apparently dissolved in the strong, hot acid solution, oxidized the iron and chromium and itself was reduced to manganese 11! then was oxidized at the anode back to manganese dioxide, and the cycle repeated. An extensive study5 of the kinetics of the oxidation of pyrite with manganese dioxide indicated that in dilute sulfuric acid solutions (about 0.1 N) and at elevated pressures the dissolution of the pyrite was brought about by air oxidation of the iron to ferrous sulfate, followed by manganese dioxide oxidation of the ferrous sulfate to ferric sulfate. The mechanism proposed by the authors involved the oxidation of the iron at the surface of the manganese dioxide. Also! the oxidation of sulfide sulfur to sulfate was credited to the oxygen in the air, not to the manganese dioxide. Since the metallurgical literature is lacking in information concerning the use of one solid to oxidize another solid. the current investigation was under-

Jan 1, 1965

By R. Al-Hussainy, P. B. Crawford, H. J. Ramey

The effect of variations of pressure-dependent viscosity and gas law deviation factor on the flow of real gases through porous media has been considered. A rigorous gas flow equation was developed which is a second order, non-linear partial differential equation with variable coeficients. This equation was reduced by a change of variable to a form similar to the diffusivity equation, but with potential-dependent diffusivity. The change of variable can be used as a new pseudo-pressure for gas flow which replaces pressure or pressure-squared as currently applied to gas flow. Substitution of the real gas pseudo-pressure has a nrtmber of important consequences. First, second degree pressure gradient terms which have commonly been neglected under the assumption that the pressure gradient is small everywhere in the flow system, are rigorously handled. Omission of second degree terms leads to verious errors in estimated pressure distributions for tight formations. Second, flow equations in terms of the real gas pseudo-pressure do not contain viscosity or gas law deviation factors, and thus avoid the need for selection of an average pressure to evaluate physical properties. Third, the real gas pseudo-pressure can be determined numerically in term of pseudo-reduced pressures and temperatures from existing physical property correlations to provide generally useful information. The real gas pseudo-pressure was determined by numerical integration and is presented in both tabular and graphical form in this paper. Finally, production of real gas can be correlated in terms of the real gas pseudo-pressure and shown to be similar to liquid flow as described by diffusivity equation solutions. Applications of the real gas pseudo-pressnre to radial flow systems under transient, steady-state or approximate pseudo-steady-state injection or production have been considered. Superposition of the linearized real gas flow solutions to generate variable rate performance was investigated and found satisfactory. This provides justification for pressure build-up testing. It is believed that the concept of the real gas pseudo-pressure will lead to improved interpretation of results of current gas well testing procedures, both steady and unsteady-state in nature, and improved forecasting of gas production. INTRODUCTION In recent years a considerable effort has been directed to the theory of isothermal flow of gases through porous media. The present state of knowledge is far from being fully developed. The difficulty lies in the non-linearity of partial differential equations which describe both real and ideal gas flow. Solutions which are available are approximate analytical solutions, graphical solutions, analogue solutions and numerical solutions. The earliest attempt to solve this problem involved the method of successions of steady states proposed by Muskat.' Approximate analytical solutions' were obtained by linearizing the flow equation for ideal gas to yield a diffusivity-type equation. Such solutions, though widely used and easy to apply to engineering problems, are of limited value bemuse of idealized assumptions and restrictions imposed upon the flow equation. The validity of linearized equations and the conditions under which their solutions apply have not been fully discussed in the literature. Approximate solutions are those of Heatherington et al.. MacRobertsl and Janicek and Katz.' A graphical solution of the linearized equation was given by Cornell and Katz. Also, by using the mean value of the time derivative in the flow equation, Rowan and Clegg' gave several simple approximate solutions. All the solutions were obtained assuming small pressure gradients and constant gas properties. Variation of gas properties with pressure has been neglected because of analytic difficulties. even in approximate analytic solutions. Green and Wilts8 used an electrical network for simulating one-dimensional flow of an ideal gas. Numerical methods using finite difference equations and digital computing techniques have been used extensively for solving both ideal and real gas equations. Aronofsky and Jenkins"I " and Bruce et al.11 gave numerical solutions for linear and radial gas flow. Douglas et al." gave a solution for a square drainage area. Aronofsky 13 included the effect of slippage on ideal gas flow. The most important contribution to the theory of flow of ideal gases through porous media was the conclusion reached by Aronofsky and Jenkins" that solutions for the liquid flow case'" could be used to generate approximate solutions for constant rate production of ideal gases. An equation describing the flow of real gases has been solved for special cases by a number of investigators using numerical methods. Aronofsky and Ferris 10 onsidered linear flow, while Aronofsky and Porter 17 considered radial gas flow. Gas properties were permitted to vary as linear functions of pressure. Recently, CarteP 18 proposed an empirical correlation by which gas well behavior can be estimated from solutions of the diffusivity equation using instantaneour values of pressure-dependent gas

Jan 1, 1967

By John B. Hastings

Chief among the varied problems facing the mine-manager is that of vein-structure and origin, which is highly important as a guide to successful discovery and development. If metalliferous deposits can be traced to the intrusion of waters along definite lines, then is there something tangible for him to study. But when he is told by a geologist that metalliferous deposits are due to some other cause, like magmatic differentiation, while not perhaps discouraged, he is impressed with a vague sense of new worlds to be conquered. In 1897, while manager of the War Eagle mine at Rossland, B. C., where, previously, the ore-bodies had not been supposed to occur as veins, I suggested to visiting members of the Canadian Geological Survey that, perhaps, the structure of the pyrrhotite-bodies of that mine, which had been proved to occur along well-defined fractures, might throw some light on the similar deposits of Sudbury, then held to be basic aggregations from the original magma. Later investigation has at least provoked discussion of this last deduction, questioning its correctness and suggesting that, perhaps, the deposits are actual veins. The following extract from a paper by J. E. Spurr' is quoted, because it sets forth Mr. Spurr's theory of the quartz-occurrences of the Silver Peak mines, which will be discussed in this article. It also graphically describes the attendant geological features. "The Drinkwater group of mines, which is the most important part of the Blair gold properties, and which has produced practically all of the million dollars' worth of ore, as above stated, may be taken as typical of the gold-veins which, though widespread and numerons, show a wonderful similarity of character. On the surface two adjacent veins outcrop, the Crowning Glory and the

Jan 1, 1906

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Eighty-four quaternary titanium-base alloys from the following systems were investigated: 1. Titanium-chromium-carbon-nitrogen. 2. Titanium-chromium-carbon with copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen with vanadium, molybdenum, or nickel. The tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships of these alloys are reported. HIS paper is the third in a series describing J- titanium-base alloys. The first paper describingdescribed titanium binary alloys, and the second contained data on a large number of titanium ternary alloys. Eighty-four heats, comprising three groups of quaternary titanium-base alloys, are described in this paper as follows: 1. Titanium-chromium-carbon-nitrogen alloys. 2. Titanium-chromium-carbon alloys containing copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen alloys containing vanadium, molybdenum, or nickel. The methods of preparing, fabricating, and testing the alloys are described in the paper Binary Titanium Alloys. Quaternary Titanium - Chromiurn - Carbon -Nitrogen Alloys The properties of titanium-chromium-nitrogen and titanium-chromium-carbon ternary alloys have been described in the paper Ternary Alloys of Titanium. Because small amounts of nitrogen and carbon both appear to be somewhat beneficial, these additions have been investigated fairly completely in quaternary alloys containing chromium at the following levels of composition: 2.5, 3.5, and 5.0 pct chromium 0.25 and 0.5 pct carbon 0.1 and 0.2 pct nitrogen Mechanical Properties: The mechanical properties of these alloys are listed in table I. Fig. 1 and 2 show graphically a comparison of the tensile properties and hardnesses of quaternary alloys with those of the titanium-chromium binary alloys. Fig. 1 shows the comparison at 0.25 pct carbon, whereas fig. 2 shows the comparison at 0.5 pct carbon. It is concluded from these data that 0.25 pct carbon and 0.1 pct nitrogen are desirable additions to the 5 pct chromium-titanium base. It is further concluded that most of this improvement is produced by the nitrogen and that carbon is either harmless or mildly beneficial, at least up to 0.25 pct. Structure and Transformation Range: The effects of carbon and nitrogen on the transformation range of the titanium-chromium alloys were determined as part of the routine investigation. Additions of 0.25 pct carbon and 0.1 pct nitrogen had no appreciable effect upon the transformation range. However, the addition of 0.25 pct carbon and 0.2 pct nitrogen definitely raised the beta solvus temperature, as shown by fig. 3.

Jan 1, 1951

By J. C. Bayles

Jan 1, 1886

By Bradley Stoughton

My attention was called by Prof. Henry M. Howe to the article by N. M. Wittorff, entitled Preliminary Investigation of Primary Crystallization and Subsequent Physico-Chemical Permutations in Iron-Carbon Alloys Containing More Than 4 Per Cent. of Carbon. I thereupon wrote to Mr. Wittorff and received a copy of the paper in the Russian language, with permission from him to publish a translated abstract in our Transactions, the original having appeared in the .Journal of the Russian Chemical Society, vol. xliii. (1911), in which it occupies some 78 pages, with 10 illustrations and 47 micrographs. The novelty of the data presented, and especially the scientific importance of Mr. Wittorff's deductions, as well as their value in helping to clarify our meager understanding of that useful but puzzling commodity, cast-iron, seemed to more than justify a publication of the essential facts in concise form in the English language, which has not been done previously so far as I know, although a very brief abstract has been published in German, and a somewhat more extended one in French.' When the work of translation was begun, I did not know that it bore in part upon the investigations of Ruff, which Howe is reviewing at some length at this meeting. This coincidence renders the following condensed translation of Wittorff's work, which I have prepared with the aid of Sidney Marcus as interpreter, the more appropriate here. The result of Wittorff's study is greatly to extend our knowledge of the hyper-eutectic alloys of iron and carbon, and to add several significant lines at the right-hand side of the diagram originally drawn by Bakhuis-Roozeboom, and developed by Roberts-Austen, Benedicks, Carpenter and Keeling, Upton, Goerens, and others. Some of the original lines of the dia-

Jan 1, 1913

By Harry W. Antes

The density changes that occurred on annealing cold-worked poly crystalline molybdenum, over the temperature range of 870" to 1630 SC, were determined. Increases in density were observed for recovery and the beginning of recrystallization. An initial decrease in density was observed during re-crystallization. A second decrease in density was observed after recrystallization was completed, as the microstructure changed from columnar grains to equiaxed gvains Both decreases in density were associated with an increase in gain boundary area to volume ratio. The second decrease in density was observed in the annealing range that immediately precedes secondary recrystallization as reported in the literature VARIOUS techniques have been used to identify the recovery, recrystallization, and grain growth processes that occur when cold-worked metals are annealed. As early as 1928 work was conducted that indicated measurable density changes occur when cold-worked single crystals of brass are annealed.' More recently, work by Murphy exhibited a corre- lation of density with microstructural changes observed on annealing cold-worked polycrystalline a brass.2 Other investigators have performed similar work on a brass and copper.324 In reviewing the literature, it was apparent that density work had been limited to fcc materials. Therefore, it was the purpose of this investigation to determine the density changes that accompany annealing the cold-worked bcc material, molybdenum. Two degrees of cold work, 30 and 90 pct reduction of cross-sectional area by rolling, were selected for this study. EXPERIMENTAL PROCEDURE High-purity vacuum arc-cast molybdenum was used in this study, the principal impurity being carbon in the amount of 80 ppm. The final rolling reductions were made at 1200°C in grooved rolls to provide 5/8-in.-diam rod. Density specimens 0.500 in. diam by 1.5 in. long were machined from the bar stock. The specimens were ground to the final dimensions to provide a smooth surface. Density measurements were made using a hydrostatic technique similar to that used by ~urphy.' This type of equipment permitted weighing in liquid immediately after the air weighing. During each weighing the temperature of the air and liquid was controlled to within 0.0l°C. This was accomplished by sealing the analytical balance in an air-tight brass chamber and surrounding it by an insulated wooden case. Preheated air was circulated in the air space between the brass chamber and wooden case by means of a blower. The temperature of the

Jan 1, 1964

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947