Search Documents

By K. E. Brown, G. H. Fancher

An 8,000-ft experimental field well was utilized to conduct flowing pressure gradient tests under conditions of continuous, multiphase flow through 2 3/8-in. OD tubing. The well was equipped with 10 gas-lift valves and 10 Maihak electronic pressure recorders, as well as instruments to accurately measure the surface pressure, temperature, volume of injected gas and fluid production. These tests were conducted for flow rates ranging from 75 to 936 B/D at various gas-liquid ratios from 105 to 9,433 scf/bbl. An expanding-orifice gas-lift valve allowed each flow rate to be produced with a range of controlled gas-liquid ratios. From these data an accurate pressure traverse has been constructed for various flow rates and for various gas-liquid ratios. A comparison of these tests to Poettmann and Carpenter's correlation indicates that deviations occur for certain ranges of flow rates and gas-liquid ratios. Numerous curves are presented illustrating the comparison of this correlation with the field data. Poettmann and Carpenter's correlation deviates some for low flow rates and, in particular, for gas-liquid ratios in excess of 3,000 scf/bbl. These deviations me believed to be mainly due to the friction-factor correlation. However, Poettmann and Carpenter's correlation gives excellent agreement in those ranges of higher density. This was as expected and predicted by Poettmann. He pointed out that their method was not intended to be extended to those ranges of low densities whereby an extreme reversal in curvature occurs.l As a result of these experimental tests, correlations using Poettmann and Carpenter's method were established between the friction factors and mass flow rates which are applicable for all gas-liquid ratios and flow rates. Definite changing flow patterns do not allow any one correlation to be accurate for all ranges of flow. INTRODUCTION The ability to analytically predict the pressure at any point in a flow string is essential in determining optimum production string dimensions and in the design of gas-lift installations. This information is also invaluable in predicting bottom-hole pressures in flowing wells. Although this problem is not new to industry, it has by no means been solved completely for all types of flow conditions. Versluys,2 Uren, et al, 3 Gosline,4 May,5 and Moore, et al,6,7 were all early investigators of multiphase flow through vertical conduits. However, all of these investigations and proposed methods were very limited as to their range of application. Likewise, many are extremely complicated and therefore not very useful in the field. Only in the last decade have any significant methods been proposed which are generally applicable. The most widely accepted procedure in industry at the present time is a semi-empirical method developed from an energy balance, proposed by Poettmann and Carpenter8 in 1952. Their correlation is based on actual pressure measurements from field wells. Accurate predictions from this correlation are limited to high flow rates and low gas-liquid ratios. Although this method will be discussed in detail later, it should be pointed out that two important parameters, namely the gas-liquid ratio and the viscosity, were omitted in their correlation. The viscosity was justifiably omitted since their data was in the highly turbulent flow region for both phases, and most wells fall in this category. The gas-liquid ratio was incorporated to some extent in the gas-density term. In 1954, Gilbert9 presented numerous pressure gradient curves obtained from field data for various flow rates and gas-liquid ratios for the determination of optimum flow strings. However, no method is presented for predicting pressure gradients except by comparison to these curves. Baxendell, et al,10 proposed a method based on Poettmann and Carpenter's procedure

By L. D. Jaffe, J. H. Hollomon

THE effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained on tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By W. E. Quist, R. Taggart, D. H. Polonis, C. J. van der Wekken

An intermediate compound that has been identified as Niab is observed to form as a decomposition product from supersaturaled Ni-Nb solid solutions during aging at temperatures between approximately 300" and 500°C. On the basis of data from electron microscopy and selected-area diffraction, the structure of this compound has been determined as fct with a = b - 3a0 and c = a, wlzere a,, is the lattice parameter of the parent solid solution. The compound consists of close-packed layers with triangular ordering, where the niobiutrl atoms are separated by two nickel atoms ([long- close?-packed directions. A nine layer stacking sequence is required to describe the proposed structure. STUDIES of the Ni-Nb binary system have been limited primarily to phase diagram determinations,'-4 investigations of high-temperature equilibrium phases,5"1 and the determination of the influence of deformation on the structure of the equilibrium compound.8 The nickel-rich portion of the binary system is reported to be of the simple eutectic type in which the maximum solubility of 12.7 at. pct Nb occurs at 1282"c.' The two-phase field below the eutectic temperature is bounded by the a fcc solid solution and an orthorhombic Ni3Nb compound. No metastable phases have been reported in previous investigations. In transformation studies of certain nickel-base commercial alloys that contain niobium, two ordered metastable compounds containing niobium have been shown to precipitate from the solid solution, both of which have been identified as y' and have the composition NisNb or Ni,Nb. One compound has been reported to have the bct DOz2 type Al3Ti structure" and the other the cubic LI2 type Cu3Au structure.9,11 In the present work on Ni-Nb binary alloys a metastable y' compound has not been detected after conventional quenching and aging treatments. An anomalous behavior was noted in electrical resistivity measurements. in alloys containing between 7 to 12 at. pct Nb when aging treatments were performed below 500°C after fast quenching from 1250°C. Transmission electron microscopy has shown that this behavior is caused by the formation of a low-temperature precipitate of unreported structure type and composition. EXPERIMENTAL METHODS Several Ni-Nb alloys, containing up to 11.5 at. pct Nb. were prepared by either levitation melting and casting in copper molds or by induction melting in alumina crucibles; both techniques employed purified helium gas as a protective atmosphere. The purity of the nickel and niobium used to make the alloys was 99.98 wt pct Ni and 99.9 wt pct Nb. The composition and homogeneity of the alloys were checked by weight measurements and by electron microprobe analysis. The induction-melted alloys were homogenized for 100 hr at 1100°C. The resistivity specimens were prepared from rods swaged to 2.5 mm and the electron microscopy specimens were cut from sheet that was rolled to 0.4 mm and thinned using a modified Bollmann technique." The elevated-temperature solution treatments were carried out in a purified helium atmosphere followed by direct quenching into a 10 pct NaCl solution at 23°C. Additional protection against oxidation of the samples during solution treatment was accomplished by using tantalum foil as a "getter" in the furnace. The specimens were aged at various temperatures in salt baths controlled to +2oC. A Leeds and Northrup K5 potentiometer was used to make electrical resistivity measurements on specimens immersed in liquid nitrogen. Electron microscopy and diffraction studies were carried out with JEM-7 and Philips EM-200 microscopes operating at 100 kv. RESULTS AND DISCUSSION Ni-Nb alloys containing between 7 and 11.5 at. pct Nb that have been solution-treated in the range 1220" to 1280°C and quenched to 23°C undergo a precipitation reaction when aged in the temperature range 300" to 500°C. Precipitation was detected by selected-area electron diffraction after aging a specimen for as little as 30 sec at 350°C) whereas the reaction was well-advanced after aging for 150 hr at 475°C. Electrical resistivity measurements were used to monitor the progress of the precipitation reaction. In the present experiments the nucleation process for precipitation required a high solution temperature and a rapid quench into brine. The presence of aluminum, iron? and carbon in amounts totaling less than 1 wt pct was found by electron diffraction to completely suppress the formation of the low-temperature precipitate that has been detected in the binary alloy. Electron diffraction techniques were used to determine the structure of the precipitates that formed during the decomposition of the Ni-Nb supersaturated solid solutions. Figs. l(a) through l(d) show electron diffraction patterns oriented to the [loo], [110], [lll], and [I031 zone axes of the matrix. Areas of reciprocal space between these sections were investigated by slowly varying the orientations of the crystal under study; this procedure revealed no reflections other than those depicted in Fig. 1. The presence of super-lattice reflections at points coincident with the matrix reflections was confirmed by the examination of an almost completely transformed structure. On the basis of the accumulated diffraction data, the reciprocal lat-

Jan 1, 1970

By J. R. Szedon, T. L. Chu, G. A. Gruber

Amorphous adherent filnzs of silicon dioxide have been deposited on silicon substrates by the oxidation of silane at temperatures ranging from 650 to 1050C. Various diluents (argon, nitrogen, hydrogen) were used to suppress the formation of SiO2 in the gas phase. Deposition rates of the oxide were determined over the temperature range in question as functions of' re-actant flow rates. Etch rate studies were used for a cursory comparison of structural properties of deposited and thermally grown oxides. From electrical evaluation of metal-insulator-silicon capacitors it was determined that the interface charge density of deposited films is similar go that of dry-oxygen-grown films in the 850° to 1050 C temperature range. Deposited films exhibit several ionic instability effects which differ in detail from those reported for thermal oxides. Stable passivating films of silicon nitride over deposited oxides appear to be practical for use in silicon planar device fabrication. Such films can be prepared under temperature conditions which have less effect on substrate impurity distributions than in the case of grown oxides. AMORPHOUS silicon dioxide (silica) is compatible with silicon in electrical properties and is the most widely used dielectric in silicon devices at present. Silica films can be prepared by the oxidation of silicon or deposited on silicon or other substrate surfaces by chemical reactions or vacuum techniques. The ability of thermally grown silicon dioxide films to passivate silicon surfaces forms one of the practical bases of the planar device technology. Properly produced and treated films of grown SiO 2 can have low densities of interface charge (-1 X 10" charges per sq cm) and can be stable as regards fast migrating ionic sgecies. 1 To maintain these properties, even with an otherwise hermetically sealed ambient, the Sia layers must be at least l000 A thick. Such thicknesses require oxidation in dry oxygen for periods of 7.8 hr at 900°C or 2 hr at 1000°C. Although oxidation in steam or wet oxygen can reduce these times to 17 and 5 min, the resulting oxides must be annealed to produce acceptable levels of interface charge., Oxidation or annealing involving moderate to high temperatures for extended periods of time can be undesirable. Under some conditions, there can be changes in the distribution of impurities within the underlying substrate. A chemical deposition technique using gaseous am-bients is particularly attractive and flexible for preparing oxide films. With a wide range of deposition rates available, films can be produced under condi- tions of time and temperature less detrimental to impurity distributions in the silicon than in the case of thermal oxidation. The pyrolysis of alkoxysilanes, the hydrolysis of silicon halides, and various modifications of these reactions are most commonly used for the deposition of silica films.3 Silica films obtained in this manner are likely to be contaminated by the by-products of the reaction, organic impurities, or hydrogen halides. The use of the oxidation of silane for the deposition process has been reported recently.4 The deposition of silica films on single-crystal silicon substrates by the oxidation of silane in a gas flow system has been studied in this work. The deposition variables studied were the crystallographic orientation of the substrate surface, the substrate temperature, and the nature of the diluent gas. The electrical charge behavior of Si-SiO2-A1 structures prepared under various conditions was investigated by capacitance-voltage (C-V) measurements of metal-insulator-semiconductor (MIS) capacitors. The experimental approaches and results are discussed in this paper. 1) DEPOSITION OF SILICA FILMS The overall reaction for the oxidation of silane is: The equilibrium constants of this reaction in the temperature range 500° to 1500°K, calculated from the JANAF thermochemical data,= are shown in Fig. 1. In addition to the large equilibrium constants, the oxidation of silane is also kinetically feasible at room temperature and above. However, the strong reactivity of silane toward oxygen tends to promote the nucleation of silica in the gas phase through homogeneous reactions, and the deposition of this silica on the substrate would yield nonadherent material. The formation of silica in the gas phase can be reduced by using low partial pressures of the reactants. Argon, hydrogen, and nitrogen were used as diluents in this work. 1.1) Experimental. The deposition of silica films by the oxidation of silane was carried out in a gas flow system using an apparatus shown schematically in Fig. 2. Appropriate flow meters and valves were used to control the flow of various reactants, i.e., argon, hydrogen, nitrogen, oxygen, and silane. Semiconductor-grade silane, argon of 99.999 pct minimum purity, oxygen of 99.95 pct minimum purity, and nitrogen of 99.997 pct minimum purity, all purchased from the Matheson Co., were used without further purification. In several instances, a silicon nitride film was deposited over the silica film. This was achieved by the nitridation of silane with ammonia using anhydrous ammonia of better than 99.99 pct purity supplied by the Matheson CO.' The reactant mixture of the desired composition was passed through a Millipore filter into a horizontal water-cooled fused silica tube of 55 mm

Jan 1, 1969

By Andrews Allen

THE large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc. have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired hoisting tonnage can be secured and, since only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining.

Jan 2, 1921

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of. Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By J. J. Carrigan

DURING the experimental stage in our use of the electric cap lamp in the Anaconda mines at Butte. Mont., we were somewhat concerned as to how the spitting of fuses would be carried out if we completely eliminated the open-flame light. This problem was at once given serious attention by the engineering research department and some thought was given to having all blasting done by the use of electric delays, which has been the practice for some years

Jan 1, 1936

By T. B. Massalski, H. W. King

An hcp phase may be induced by cold working the ß&apos; phase of the Ag-Zn system. This phase reverts to ß&apos; on subsequent aging. No phase change occurs on cold working the o phase, but ß&apos; is formed when the deformed alloy is subsequently aged at room temperature. It is concluded that for alloys near 50 at pct Zn the ordered bcc ß&apos; phase is the equilibrium structure at room temperature. WhEN the disordered bcc ß phase of the Ag-Zn system is cooled to temperatures below 258o to 274oC, it transforms to a complex hexagonal phase <o.1,2 The nature of the o ß=o transformation has been the subject of some discussion,2&apos;3 and the structure of o has been described in detail.&apos; The latter phase appears to be stable on aging at room temperature but decomposes following cold work. When alloys containing approximately 50 at. pct Zn are rapidly quenched from the 0 phase field, the ß ? o transformation may be suppressed; but the ß phase undergoes an ordering reaction (ß ? ß&apos;). The ß&apos; structure may also be obtained as a result of cold working and aging at room temperature.4 Kitchingman, Hall, and Buckley4 have suggested that the decomposition of (o following cold work proceeds in two stages, (o ? ß followed by ß ? ß&apos;, but did not confirm this by experiment. When the ordered &apos; phases in the systems Cu-Zn5 and Ag-Cd6 are cold worked, they become unstable and transform to a close-packed hexagonal phase (( ) indicating that when order is destroyed in a ß&apos; structure the close-packed hexagonal phase may in many cases be more stable. It thus became of interest to study more closely the effect of cold work and annealing on the stability of both the ß&apos; and o phases in a Ag-50 at. pct Zn alloy. Predetermined weights of spectroscopically-pure Ag and Zn, supplied by Johnson and Matthey, were melted and cast under 1/2 atm of He in transparent vycor tubing. The ingot was homogenized for 1 week at 630°C and quenched into iced brine. Since mechanical polishing was found to induce a phase change, sections were first polished at room temperature, sealed in tubes under 1/2 atm of He, reannealed for several days at 630o or 200°C and then quenched into iced brine. Sections of the alloy thus prepared were found to be homogeneous when examined under the microscope. The sample quenched from 630°C (ß -phase region) was pink in color, whereas the sample quenched from 200°C (o-phase region) was silver. The latter sample showed the characteristic hexagonal anisotropy when examined under polarized light. Filings of the alloy were examined at room temperature, after various heat treatments, using an RCA-Siemens Crystalloflex IV diffractometer with filtered CuKa radiation. The X-ray reflections from flat powder specimens quenched from 630o and 200°C and sieved through 230 mesh were recorded graphically at a scanning speed of 1/2 deg per min. The resultant patterns are shown in Figs. 1(a) and 1(b) and may be identified as those of the 8&apos; and <02 structures respectively. The lattice parameter of the ß&apos; phase was determined as 3.1566Å.* This value compares very well withthatto be expected for a 50 at. pct Zn alloy from the data of Owen and Edmunds? and indicates that no loss of Zn occurred during casting. In order to study the effect of cold work upon the ß&apos; and o phases, filings made at room temperature and sieved through 230 mesh were mounted immediately in the diffractometer-i.e., without a strain-relief anneal. Changes in structure on subsequent aging were followed by scanning repeatedly over the regions of the low index reflections of the ß&apos; and o structures-i.e. , 28 from 35 to 44 deg. Immediately after filing the 8&apos; specimen, additional diffraction peaks were observed in the low-index region of the pattern, as shown in Fig. 1(c). These additional peaks do not coincide with those of the o structure, Fig. l(b), but may be indexed as the (10.0), (00.2), and (10.1) reflections of an hcp phase (<) with nearly ideal axial ratio. However, this hexagonal phase appears to be very unstable since within a very short time at room temperature it reverts back to the ordered ß&apos; phase, the reversion being complete within seven hours. The 5 ? ß&apos; reversion reaction is, therefore, very similar to those already reported in Cu-Zn5 and Ag-Cd6 7&apos;alloys. The action of filing caused the deformed surface of the originally pink ingot to become silver in color, indi-cating that the ( phase possesses similar reflecting properties to the o phase. Hence, the subsequent

Jan 1, 1962

By Rixford A. Beals

It has been observed with considerable accuracy that if the major U. S. mines were moved to Mexico tomorrow, many of them would be losing money. But the companies would continue to operate, losses or not, because they would have to. And some of the newest and most promising low grade ore projects in the U. S. would never have "gotten off the ground" had they faced the equivalent of the mining taxes now in effect in Mexico. No one of the various mining taxes in Mexico seems prohibitive by itself. Taken together, on the balance sheet, however, the picture changes. Production and export taxes alone take from 20 to 40 pct of the gross product value for base and precious metals.

Jan 2, 1955

By A. L. Lee, M. H. Gonzalez, R. F. Bukacek

Experimental viscosity data for methane are presented for temperatures from 100 to 340F and pressures from 200 to 8,000 psia. A summary is given of the available data for methane, and a comparison is presented for that data common to the experimental range reported in this paper. Correlation of the data is presented, and predicted values are given for temperatures up to 460F and pressures up to 10,000 psia. INTRODUCTION The increasing ranges of temperature and pressure at which fluids are produced, transferred and processed in the petroleum and chemical industries stress the need for accurate information on physical properties, both for engineering calculation and for improving the methods used to estimate physical properties. A survey of the literature reveals that disagreements between published data on the viscosity of methane are common and that most investigations have been conducted over restricted temperature and pressure ranges. This situation made it desirable to undertake an investigation with a scope common to most of the literature data available. APPARATUS AND MATERIALS The apparatus used in this investigation was the capillary tube viscometer&apos;described by Dolan,10 with modifications introduced in the general design and operation of the instrument. It has an effective pressure range from 14.7 to 10,000 psia and a temperature range from room temperature to 400F. The design of the viscometer is based on the establishment of a manometric head between two vessels containing the test fluid and a volume of mercury. The reservoirs are connected by a capillary tube through which the test fluid flows and a tube through which mercury flows. A pressure gradient is established by elevating one of the vessels above the other, the resulting flow of mercury displacing the test fluid through the capillary. The schematic diagram of the system (Fig. 1) shows the arrangement of the equipment auxiliary to the viscometer. The density cells assembly (E, Fig. 1) was not used in this investigation since reliable data are available on methane. 23 The assembly consists of a bank of eight 316 stainless steel pycnometers. Experimental values of the density of a natural gas19 and i-butane14 samples have been obtained for pressures up to 8,000 psia and temperatures up to 340F. The methane used was obtained from the Southern California Gas Co. Mass spectrometric analysis showed a composition of 99.8 percent CH4, 0.1 percent C2H6 and 0.1 percent C3H8. EXPERIMENTAL VALUES AND ACCURACY OF DATA Determinations were carried out at several temperatures. With the temperature in the cabinet controlled at a given level, a series of runs were made at various pressures. To establish pressures lower than that obtained from the methane cylinder, it was necessary to vent the gas slowly to the atmosphere until the desired pressure was reached. The consistency of the test run time for a particular condition can be used as a criterion for the accuracy of the data. A further check is obtained by comparison of the viscosity values obtained using different driving heads. To establish the instrument&apos;s reproducibility, a large number of runs were made at three completely different conditions of temperature and pressure. Data obtained were analyzed statistically to determine the most reliable value for the variance of the experimental data. It was found that the variances of the data taken at different experimental conditions were not statistically equivalent, but they were small. The largest variance was found at 8,000 psia and 100F, where the standard deviation was 0.385 micropoise. Therefore, 99.9 percent of the data can be expected to fall within 1.15 micropoises of the population mean, except for the intervention of systematic errors in operation.

By Russell Spry, Paul Schutz

The property of Pioneer Gold Mines of B.C. Limited is in the Lillooet mining district of British Columbia. It is on Cadwalleder Creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern Railway. Interests identified with the present company installed a small amalgamation plant on the property in 1924, consisting of a jaw crusher, Bryan mill and amalgamation plates, in which 75 per cent extraction was made on mill feed averaging 1.0 oz. gold per ton, the tailing being stacked for future treatment. That plant was operated until 1928, when the present company was formed and a 100-ton continuous counter current decantation cyanide plant was built. A second unit, having a nominal capacity of 200 tons daily, was added in 1932 and put into operation during September of that year. When handling ore comparatively free from slow-settling material, the combined capacity of the two units is 400 tons, the original plant now handling about 140 tons maximum. Production to date, from Pioneer, has been about $6,500,000, the present monthly production being better than $250,000 from about 370 tons ore daily, the recovery being 97 per cent. During the fiscal year ending March 31, 1934, a total of 112,936 tons ore and old amalgamation tailing was milled, the mill feed averaging 0.7670 oz. gold and the recovery amounting to 0.7422 oz. gold per ton, or 96.77 per cent. Milling costs, including refining and mint charges, during this period, amounted to $1.45 per ton of ore. Since the building of the first unit of the cyanide plant in 1928, direct cyanidation has been employed, no attempt being made to remove coarse gold from the circuit, other than that cleaned up from the grinding mills during relining and from the classifiers, as occasions permit. In the hope of still further increasing recovery, researches are going forward at this time with the view to removing some of the sulfides after primary grinding, the expectation being that selective treatment of this more refractory portion of the ore may hold economic possibilities.

Jan 1, 1935

Taking advantage of the lessons in administrative organizations which were taught by the war, Director Van H. Manning has put into effect a new form of organization in the Bureau of Mines. The Bureau is divided into two branches, one the investigations branch and the other the operations branch. F. G. Cottrell, who has been chief metallurgist of the Bureau, has been promoted to the position of assistant director and will be in charge of the investigations branch. F. J. Bailey, who has been chief clerk of the Bureau, has been placed in charge of the operations branch with the title of, assistant to the director. All research and technical control will be exercised through the investigations branch, while the non-technical work, administrative duties, and dissemination of the results of the Bureau&apos;s activities will be handled by the operations branch. Under the investigations branch comes the division of mineral technology, in charge of Dr. C. E. Parsons; the division of fuels, under the chief mechanical engineer, 0. P. Hood; the division of mining, under the direction of George S. Rice, the chief mining engineer; the division of petroleum and natural gas, under the direction of J. 0. Lewis, the chief petroleum technologist; and the division of experiment stations, under the direction of D. A. Lyon.

Jan 9, 1919

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O&apos;Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by i0 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle&apos; in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By R. Costantini

Long-distance transportation of solids by hydraulic pipelines holds promise of great economic benefits. In most mineral processing plants today, moving of solids in slurry-form by pipeline is commonplace. Yet in spite of this, the method is slow in being adopted on a broad scale for moving solids over distances of many miles. This is especially surprising in view of the successful realization of two daring ventures in long-distance solids pipelines in this nation within the last five years. One is the 72-mile long, 6-in. diam. pipeline of the American Gilsonite Co. which has been satisfactorily transporting 700 tpd of gilsonite from the mine at Bonanza, Utah, to the processing plant at Grand Junction, Colo., since April 1957. The other is the 108-mile long, 10-in. pipeline of the Pittsburgh Consolidation Coal Co., which has been transporting about 4000 tpd of finely crushed coal from the mine at Cadiz, Ohio, to the Eastlake Power Plant of the Cleveland Electric Illuminating Co. since January 1958.

Jan 8, 1961

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Graduate mining engineer, with 10 years&apos; experience, having an office in New York, would like to represent a mining company as selling and purchasing agent, and general supervision if desired. Machinery agency considered. No. 259. Member, technical graduate, with several years&apos; experience as engineer for a pyrites company, and as geologist and engineer for copper, nickel, and silver companies, desires a position as engineer or superintendent of mines. No. 260. Member, technical graduate, aged 29, with experience as draftsman, surveyor, and superintendent of iron and gold mines, and as construction engineer, is open for a position as mine superintendent, or in mine examination or construction. No. 261.

Jan 11, 1915

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook&apos; has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries&apos; method for grain-size measurements consists of counting the number

Jan 1, 1948

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook&apos; has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries&apos; method for grain-size measurements consists of counting the number

Jan 1, 1948

By J. W. Snavely

THE high tension belt conveyor is introducing a new and tremendously expanded era of low cost bulk material handling. High tension belt conveyors are generally those installations involving very long centers, high lifts, or drops, in which the belts are stressed up to their maximum tension values, and further, where the belt construction provides tension capacity far beyond what is possible with conventional belt constructions. With these high tension installations, the magnitude of the forces involved demands careful refinement of accepted design practice in order to achieve optimum balance of all factors. No attempt will be made to evaluate the relative merits of belt conveyor haulage with other means of transportation. For present purposes, it is assumed this has already been done in favor of belt conveyor. Neither will any attempt be made to evaluate the various conveyor belt constructions now available or to balance the advantages of various types of mechanical equipment. It is also assumed that the basic haulage information on which the conveyor design is based is accurate and complete. A sustained maximum, uniform load on the belt at all times must be achieved through proper feed control and the use of adequate surge storage to level the peaks and valleys of any varying demand for the material being handled. General Belt Capacity Considerations The belt conveyor capacity tables published by various belting and conveyor equipment manufacturers vary to a considerable degree, and the ratings given are quite conservative. Of necessity, these published ratings are based on the handling of average materials under average conditions. In applying a high tension belt, all possible capacity from the belt must be obtained in order to hold its width to a minimum and thereby limit the initial cost. Two factors are involved, loading to maximum cross section area and traveling at a maximum practical speed. Belt Loading: Proper treatment of the loading of the belt will result in maximum cross section to the load, and published capacity ratings can be exceeded, sometimes by appreciable margins. On the 10-mile conveyor haul used in the construction of Shasta Dam, California, although the rated capacity of the belt line was 1100 tons per hr, at times the system handled peak loads of 1400 tons per hr, almost 25 pct better than the rated capacity. One of the large coal companies has been able to exceed rated capacity by as much as 50 pct. Loading conditions which must be controlled are: 1. Large lumps must be scalped off and rejected or the load must be primary crushed before being placed on the belt. 2. The material weight per cubic foot must be accurate, must be known for all the materials being handled, and must be known for the complete range of conditions of the individual material being handled. Long centers and high lifts magnify small differences into serious proportions. 3. Uniform feeding to the belt is most important. Various types of feeders are available, which can be used to place a constant predetermined volume of material on the belt, or, where an appreciable range of material weight exists, through electrical control actuated by current demand, to place a predetermined uniform tonnage on the belt. One long slope belt in a coal mine in Pennsylvania is being fed at three separate stations with the controls so arranged that whenever the maximum load is going onto the belt from the first station, the other two stations automatically cut out. Whenever the load from the first station drops back, the other two stations again automatically cut in. 4. Careful design of the chutes and skirts is necessary to get the load centered on the belt with a minimum of free margin along each edge. Some free margin at the edge of the belt is necessary to prevent spillage, but if the load can be kept accurately centered, this free margin area can be reduced, and more material can be carried on the belt. What can be accomplished in this respect will vary widely, depending on the nature of the material being hauled. The chute and skirt design must also protect the belt. 5. The design of chutes and skirts should also get the load traveling in the same direction and close to belt speed, so that the load comes to rest on the belt as quickly as possible. The design of the chutes and skirts is worthy of careful study, and after a system is put into operation it should be experimented with to get the best results. Belt Speed: High belt speeds should be used in high tension work. Obviously, high belt speeds enable haulage on a narrower belt, reducing initial cost. The major portion of belt wear takes place at the loading point and around the terminal pulleys. The

Jan 1, 1952

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

By Stephen G. Dardaganian

Pore volume compresibilitieu measured in the laborutory on core .samples are reported for typical reservoir .sarrrl.rtorres at reservoir pressure. These cornpressibilities ore different for each reseriloir sample and cannot be correlated to porosity. The compressihilities are a1so functions of presslire. In recent years several authors have pointed out the importance of including pore volume compressibility of the reservoir rock in certain reservoir engineering calculations. Hall&apos; showed that in calculating the hydrocarbon volume of an undersaturated reservoir from the production per unit change in reservoir pressure, the neglect of rock compressibility could, in the extreme case of low porosity rock, lead to results in error by a factor of two. Hawkinsl&apos; and Hobson and Mrosovsky showed that both rock and interstitial water compressibilities must be included to achieve satisfactory accuracy in this calculation. Although rock compressibility is an important reservoir property in these calculations, very few data are available. Hall&apos; made compressibility measurements on a few samples in a small pressure range. No other direct pore volume compressibility measurements have been reported. Geertsma&apos; discussed the elasticity of reservoir rock but did not present any new data. In this paper, rock compressibilities suitable for reservoir calculations are reported for a variety of sandstones typical of U. S. reservoirs. The measurements were made through a range of pressures which is also typical of reservoirs. EXPERIMENTAL PROCEDURE Plugs 1 in. in diameter and 2- to 3-in. long were diamond drilled, 14 from cores from seven oil-bearing or potentially oil-bearing sandstone, one from a quarried sandstone, and another from a shallow, oil-free, pure orthoquartzite. The plugs were extracted in toluene, vacuum dried, and then weighed. The plugs were then saturated with kerosene and reweighed. This gave pore volume. They were then again extracted in toluene. vacuum dried, and jacketed in 0.004-in. thick copper foil. A short length of -in high pressure tubing led from the jacket. The jacketed sample was then saturated with kerosene and placed in the hydraulic pressure cell as shown in Fig. 1. Movement of the mercury slug showed the change in pore volume of the sample under a given pressure change. Temperature was about 72" F for all measurements. Before taking any measurements, the external pressure on the sample was raised to 10,000 psig and kept there for several hours. This formed the thin copper jacket around the plug. 7-he pressure was then removed and the sample left at least overnight, during which time it recovered its original pore volume. An external pressure of 12,000 psig was then applied and held constant. The change in pore volume was noted as the internal pressure was raised in 1,000 psig increments to 10,000 psig. The internal pressure was then reduced to zero, again noting pore volume changes,