Search Documents

By H. R. Deeth, C. J. Koenig

ABOUT ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spence1 described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Corp. at Rochester, N. Y. THE DEPOSIT Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 [VOLUMETRIC MINERAL PER CENT Albite54 Microcline20 Nepheline22 Muscovite2 Mafics2 (Biotite, hastingsite, magnetite) Total100] The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2O A1203 6SiO2) and microcline (K20 A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1947

By Henri V. Reibell

Deep open pit optimization supposes very long and sedious calculations in order to assign the best shape of the pit and the best bottom level, which will give the biggest profit. Computers give the possibility to make these calculations. More over, they allow to multiply trial calculations so that it is possible to obtain more reliable results. The paper does not expose the computer program but only the way in which mining engineers can use it.

Jan 1, 1969

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By Murl R., Schrock

THE use of diamond-drill holes at the Moctezuma Copper Co., Pilares mine, Pilares de Nacozari, Sonora, Mexico, for the ventilation of raises has resulted from experiments that were made in an effort to secure continuous and efficient ventilation in hot and gaseous raises. The method is particularly applicable in long raises and in raises run from development levels where the source of fresh air is distant. In order that the CO, concentration shall not become excessive, 30 cu. ft. per min. per man must be supplied to a heading for breathing purposes:&apos; The quantity of air that will pass through a diamond-drill hole by

Jan 1, 1929

By William O. Hotchkiss

IN COMMON with every other good citizen I long for conditions that will make perpetual peace a reality throughout the world. I have studied the statements of our public men relating to what we must do to bring this about after this war is over. In most of these I find one common error. They always build their plans on the unstated, subconsciously accepted premise that there can be such a thing as an ideal nation whose citizens are possessed of infinite wisdom and actuated only by motives that are above reproach. This heavenly vision fails to correspond with the facts. We wish it could be true but we are forced sadly to admit that the human beings that will live here after this war is over are going to be much like the fallible race that has occupied our planet for the past centuries.

Jan 1, 1943

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

IT is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references 1 to 4. Investigations on the properties at elevated temperatures are few, however,5-7 and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. As is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hardening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During [TABLE I.-Sources of Materials Used in the Testing Program MATERIAL ORIGIN AND TREATMENT 24S-T Alclad.... From Lockheed stock. 24S-RT Alclad... Direct from mill. 24S-T80 Alclad.. 24S-O Alclad from Lockheed stock, solution-heat-treated (925°F., water quench) and aged at 375°F. for t0 t % hour. 24S-T8I Alclad.. 24S-T Alclad from Lockheed stock, plant stretched up t0 I per cent and aged t0 ± % hr. at 375°F. 24S-T86 Alclad.. 24S-RT Alclad from Lockheed stock aged 534 ± 34 hr. at 375°F. 6IS-W (bare).... From Lockheed stock. 6IS-T (bare) 6IS-W (bare) from Lockheed stock aged 8 hr. at 350°F. XB7SS-T Alclad. From Lockheed stock.] the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "overaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: I. The higher the temperature, the more rapidly is the fully aged condition attained.

Jan 1, 1945

By H. R. Deeth, C. J. Koenig

About ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spencel described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Cory. at Rochester, N. Y. The Deposit Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 Volumetric Mineral Per Cent Albite.................... 54 Microcline................ 20 Nepheline................ 22 Muscovite................ 2 Mafics.................... 2 (Biotite, hastingsite, magnetite) Total................... loo The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2oA12O3 6SiO2) and microcline (K2O A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1949

By Oliver B. Knight

The producing formation in the South Field, or "Golden Lane" structure of Mexico, is a buried ridge of reef limestone of Comanchean age overlain unconformably with sediments of Upper Cretaceous, Eocene and Oligocene. The structure extends in a long sweeping arc, with the convex side toward the west, from San Geronimo, Vera Cruz, to San Isidro, south of the Tuxpam River, which it crosses at the town of Alamo. It is 52 miles long and averages 3/4 mile in width. The surface of the producing formation of El Abra limestone consists of a series of minor parallel highs which are separated longitudinally by synclinal troughs and laterally by structural saddles. The presence of these highs has been of utmost importance in the development of the field, especially in recent years when the salt-water level has risen above the synclines and confined the oil to the isolated highs. In many cases, faulty information and interpretation of the subsurface has resulted in drilling costly dry holes and salt-water wells. Development The development of the Golden Lane was started by the Mexican Eagle Oil Co. in 1906. San Diego No. 3, usually known as Dos Bocas, the first producing well on the structure, was completed on July 4, 1908. This well came in unexpectedly for an estimated daily production of 129,000 bbl., and, as the casing was not properly set, the well flowed wild into the Tamiahua Lagoon, causing a loss of several million barrels of oil. In flowing wild the well formed a crater which covers an area of 48 acres, out of which salt water and small quantities of gas still flow. Casiano No. 2, the Huasteca Petroleum Co., which yielded 200 bbl. of oil daily, and which was completed in November, 1909, was the next producing well to be drilled on the structure. In 1910, the same company completed Casiano No. 7, with an initial production of 50,000 bbl. daily, and Casiano No. 1, which produced 200 bbl. daily. In the same year, the Mexican Eagle Oil Co. completed its Potrero del Llano wells 1, 2 and 4, with initial productions of 500, 400 and 100,000 bbl. respectively. From 3910 to the latter part of 1919, development proceeded

Jan 1, 1931

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By H. C. Gatos, A. D. Kurtz

WITH the growing interest in the mechanism of self-diffusion of metals, the study of accurate and convenient methods for determining self-diffu-sion coefficients appears highly desirable. It was with this objective in mind that the present investigation was undertaken. Gatos and Azzam1 employed an autoradiographic technique for measuring self-diffusion coefficients of gold. This method involved sectioning of the specimen through the diffusion zone and recording the radioactivity directly on a photographic film. Because of the very short range of the emitted ß rays in gold, the activity recorded on the film was essentially the true surface activity. With proper choice of the sectioning angle, sufficient resolution could be obtained and the entire concentration-distance curve recorded in one measurement. For the boundary conditions of the experiment, where an infinitesimally thin layer of radioactive material diffuses in positive and negative directions into the end faces of a rod of infinite length, the solution of the diffusion equation is C/Cn = 1/v4pDt exp (-x2/4Dt) where C is the concentration of diffusing element (photographic density in this case), C,, is the constant (depending upon amount of radioactive material), x is the diffusion distance, D is the diffusion coefficient, and t is the time. Thus, by plotting the logarithm of the concentration vs the square of the diffusion distance, a straight line results and the slope contains the diffusion coefficient. In this manner, the self-diffusion coefficient of gold can be obtained as a function of temperature. In the present investigation the results reported by Gatos and Azzam1 have been verified, and the autoradiographic technique has been further developed and applied for the determination of the self-diffusion coefficient of gold at a number of temperatures. Furthermore, the energy of activation for the self-diffusion of gold has been conveniently determined. . Experimental Techniques Preparation of Specimens: The inert gold of high purity was received in the form of a rod from which cylinders were cut and machined to a diameter of 0.500 in. The specimens were annealed to a suitably large grain size and the faces were surface ground prior to the deposition of the radioactive layer. The radioactive isotope Au198 was chosen. It was produced in the Brookhaven pile by means of the reaction Au197 + n ? Au108. It decays by ß emission (0.96 mev) to Hg108 with the subsequent emission of a y ray (0.41 mev). 70Au 108 ? 80Hg 108 + -1e°. The half life of the Au108 is 2.7 days so that a strict time schedule had to be maintained in order to secure sufficient activity until the end of the experiments. For this reason, initial activities as high as 10,000 millicuries per gram were used. The gold arrived in the form of foil and was evaporated onto one face of each gold specimen cylinder to a thickness of about 100A. A sandwich-type specimen was formed by welding two such cylinders together. Evaporation of Gold: The gold was evaporated under vacuum from heated tantalum strips which were bent in such a way as to limit the solid angle through which the gold was allowed to vaporize, thus insuring a more efficient utilization of the gold. The specimens rested on flat brass rings which had an inner diameter of 0.475 in. The entire specimen-holding assembly could be manipulated from outside the vacuum system by means of a magnet which attracted a slug of soft iron attached to the assembly. By evaporating inert gold on glass slides under conditions identical to those employed for the radioactive gold, it was found that the thickness of the films was about 100A. Welding: The welding was performed by hot pressing in a stainless steel cylinder. The inside of the cylinder was threaded and fitted for two plugs. The specimens to be welded were placed in the middle of the cylinder and two pressing disks, one at each end, were inserted to avoid shearing stresses as the plugs were tightened. Mica disks were placed between the pressing disks and the specimens to prevent them from welding. The plugs were then tightened with a hand wrench and the entire unit was placed in an argon stream for about an hour to remove the oxygen. The unit was then inserted in the center of an argon atmosphere furnace maintained at about 700°C and left there for about an hour. Because of the difference in the temperature coefficient of expansion of the two metals, as the temperature rose. the pressure on the specimen-rollple increased and a weld resulted Welding was generally satisfactory under the conditions described.

Jan 1, 1955

Jan 1, 1943

By D. W. Levinson, L. F. Mondolfo, N. A. Gjostein

MANY investigations are reported in the literature on the age hardening of Al-Mg-Zn alloys but most of them are concerned mainly with mechanical property changes. The present investigation was started to determine the structural changes in an AlMgZn alloy. The alloy composition was chosen in the existing phase diagram" so as to lie on the quasi-binary section Al-(AlZn)Mg Actually, it was found that the diagram as published was inexact at the lower temperatures and that the phase in equilibrium with aluminum at the lower temperatures is not the ternary compound. Technique The alloy used for the investigation was prepared from high purity materials and the resulting composition as determined by chemical and spectro-graphic analysis was: Zn, 6.17 pct; Mg, 2.13 pct; CU, 0.03 pct; Si, 0.009 pct; Fe, 0.005 pct; and the remainder, aluminum. An ingot -in. thick was cast, homogenized, hot and cold-rolled to strip 0.064-in. thick for dilato-metric and powder work, and to foil 0.005-in. thick for single crystal work. Solution treatment temperature for all specimens was 475°±5°C for periods of at least 1 hr, either in air furnaces or lead baths. Aging was done in oil or Pb-Bi baths controlled to within ±3°C. The aging was investigated at the following temperatures: room (30°), 130°, ZOO0, 260°, and 300°C. For the dilatometric study, the length changes were measured continuously, at temperature, using strips of alloy 10 in. long, shaped as channels to eliminate undesirable deflection due to bending. To compensate for thermal expansion and contraction due to the variations in the temperature of the aging baths, the dilatometers were built of the same alloy as the one being tested, with the same shape and size, but with material fully annealed. Gages on which 0.0005 in. could be read and 0.0001 in. estimated were used to measure the dilation. Length changes were also measured at room temperature. Strips approximately 10 in. long were solution-treated, quenched, and measured in a supermicrome-ter in which 0.0001 in. could be read and 0.00001 in. estimated. The specimens were immediately aged for a given time, remeasured, and then the cycle was repeated, including the solution treatment. The error of measurement with this technique was somewhat larger, but the results confirmed those obtained by continuous measurements. The sheet used for the dilatometric work was checked to determine grain orientation. Both X-rays and etching methods revealed a rather coarse grain size but only a negligible amount of preferred orientation. Thus, volume changes calculated from length changes are not invalidated by preferential orientation effects. Pieces of the sheet used for the dilatometric work were also used for the metal -lographic work. Filings for the powder X-ray study were produced from a homogenized piece of sheet. These filings were magnetically purged of iron, screened to 200 mesh, sealed in a Pyrex tube containing an argon atmosphere, and solution-treated. When quenching, the glass tube was broken, so that the powder dropped directly into cold water. After drying with alcohol, the powder was sealed into capillary tubes containing an argon atmosphere and then aged for the required times. In spite of all these precautions the three strongest lines of a( Al2o) appeared in all patterns, and were used as internal standards. By the use of these standards, accurate corrections for film shrinkage were obtained. For the back reflection patterns, annealed nickel powder was mixed with the specimen to act as internal standard. A preliminary investigation was made in small (57.3 mm diam) powder cameras. From these patterns the changes which took place in the solid-

Jan 1, 1957

By C. H. G. Bushell, James E. Lawver, William Barbarowicz

Proper use of automatic controls in the process industries is a combination of art and science. Although many phases of automatic control theory can be expressed by precise mathematical relationships, the final control arrangement usually requires considerable effort by trial and error before the optimum control circuit is found. The failure of flotation operators to recognize that control circuits require study and plant experimentation before satisfactory operation occurs has led to a popular misconception that flotation plants simply do not lend themselves to automation. This widespread belief has been overcome to some degree in recent years by the numerous installations of automatic controls that have paid their way by increasing profits in terms of increased recoveries, lowered costs, or higher grade concentrates. WHY CONTROL ? Any form of automation must be justified in terms of ultimate return on in- vestment by improving quality, by increasing plant throughput, or by reducing the total operating costs. Generally speaking, automatic controls rarely re- place a mill operator. They assist the operator in holding important variables within predetermined limits. Large tonnage operations usually can justify a great deal of automation because an increase in one or two units of recovery results in enormous savings compared to the capital and operating costs of controls. DETERMINATION OF CONTROL The first questions in considering plant automation are: 1) What variables must be controlled? 2) What are the optimum levels of the variables? The optimum operating conditions for any process are those which maximize profits. Many of the variables active in flotation processing can be determined by experimentation in the laboratory or pilot plant 10. Although laboratory experiments can pinpoint variables, the true optimum conditions existing at plant level usually must be determined by plant scale experiments. In recent years, the concepts of detailed experimental designs in the laboratory, followed by plant experiments, have reached the stage of maturity where

Jan 1, 1962

By J. B. Austin, R. H. H. Pierce

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of, carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is .cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ?-a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dilatometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has. been described.2

Jan 1, 1935

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world&apos;s largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

Jan 1, 1943

This is a brief account of the history of unit operation in the Salt Creek field, Wyoming, from the time of the agreement to prorate production in March, 1921, to the present. An attempt has been made to evaluate the savings in development and production costs resulting from the unit plans adopted. Summarized, these savings have amounted to $11,650,000. No effort has been made to estimate any increase in ultimate recovery, for it is believed that unit operation can be justified on saving in development and production costs alone. It would require nearly 20,000,000 barrels of additional oil to be produced in order to return the amount saved by not drilling unnecessary wells. Four horizons are affected by unit or near-unit programs, as follows: The principal operator is under contract with six companies to operate 10,400 acres. This includes all of the productive area of the First Wall

Jan 1, 1930

By H. W. Schull

The Alligator Ridge gold deposits are located in northwest White Pine County at the southwest end of Alligator Ridge. Alligator Ridge is on the west side of Long Valley in the range of hills that separates Long and Newark valleys. The nearest population center is Ely, about 113 km (70 miles) to the southeast. Access to the Alligator Ridge gold mine from Ely is via US Highway 50 and the Long Valley Ruby Marsh Road. The latitude and longitude is approximately 39° 45&apos; north and 116° 30&apos; west. The Alligator Ridge gold deposits occur in the lower 61 m (200 ft) of the Mississippian-Devonian Pilot Shale formation, a laminated calcareous carbonaceous siltstone. The gold deposits contain carbonaceous, oxide, and jasperoid type gold ore. For more details on the geologic features of the deposits, see Schull, Sutherland, and Ilchik (in press). The discovery story of Alligator Ridge began in the spring of 1976 when the areas mapped as jasperoid on the 1:250,000 scale geologic map of White Pine County (Hose and Blake, 1976) were examined and sampled. Seventeen samples, about 23 kg (50 lb), were collected from an area about 0.65 km2 (0.25 sq mile). Of these 17 samples 10 reported atomic absorption values of less than 0. 1 ppm Au and 7 reported values in the 0.1 to 1.0 ppm Au range. In June of 1976 20 lode claims were staked to claim the area of the rock chip sampling. The claims&apos; end and side center lines were used as a grid for soil sampling. Sample stations were 91 m (300 ft) apart and sample lines were 229 m (750 ft) apart. The samples were sieved to - 180 µm (- 80 mesh). Out of 99 soil samples, seven samples reported Au values in the 0.1 to 1.0 ppm range. Of the seven auriferous samples, five were located over the jasperoid outcrops previously sampled; one over unmineralized Pilot Shale a few hundred m (ft) downslope from some Au-bearing jasperoid; and one from a 15 x 15 m (50 x 50 ft) talus outcrop area of hitherto unnoticed mineralized Pilot Shale. Subsequent sampling, mapping and drilling would show that this 15 X 15 m (50 x 50 ft) outcrop area was the top of the Vantage 1 ore body, about 1.27 Mt (1,400,000 st) of over 3 g/0.9 t (0.11 oz/st) Au. Late in the summer of 1976 about 30 more 1.4 to 2.2 kg (3 to 5 lb) rock chip samples were collected in the course of preliminary geologic mapping. This mapping and sampling showed that the gold-bearing jasperoids occurred at the contact between the Pilot Shale and the underlying Devils Gate Limestone. Rock chip samples of 0.1 ppm Au or greater were restricted to the jasperoids and the mineralized outcrop area of Pilot Shale located by the soil sample survey. Rock chip samples from the area of mineralized Pilot Shale were in the 3 to 5 ppm Au range. Activity resumed in the summer of 1977 with a more detailed soil geochemical survey. The jasperoid areas were defined as large geochemical gold anomalies of values greater than 0.1 ppm and locally greater than 0.2 ppm Au. Soil samples from the area of mineralized Pilot Shale outlined a greater than 0.1 ppm gold anomaly 61 x 152 m (200 x 500 ft) in size. Further geologic mapping showed that elsewhere, even where bleached and silicified, the Pilot Shale areas were geochemically very low in gold (less than 0.1 ppm Au). In November, 1977 twelve rotary percussion drill holes were drilled to test the gold-bearing jasperoid areas and the mineralized Pilot Shale area. Drilling of the jasperoid areas showed that the jasperoids gave way at shallow depths [less than 24 m (80 ft)] to unmineralized unaltered Devils Gate Limestone. A five hole cross pattern was drilled to test the area of mineralized Pilot Shale. Four of the five holes re-

Jan 1, 1985

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period April 1 to 15. William B. McKinley, New York, N. Y Collier Cobb, Chapel Hill, N. C. C. W. Goodale, Butte, Mont. E. P. Fleming, Guayacan, Chile. D. C. Brown, San Luis Potosi, Mex. Albert Sauveur, Cambridge, Mass. W. H. Rettie, Yonkers, N. Y. H. M. La Follette, La Follette, Tenn. Mark B. Kerr, San Francisco, Cal. E. Fleming L&apos;Engle, New York, N. Y. H. W. Turner, San Francisco, Cal. H. Garlichs, St. Louis, Mo. Frank M. Leland, Mackay, Idaho. Henry Hay, London, England. Sir Robert Hadfield, London, Eng. Edward J. Way announces that his agreement as consulting engineer in South Africa for the Anglo-French Exploration Co., Ltd., having terminated, he will engage in professional consulting work with headquarters at 135 Cullinan Buildings, Simmonds St., Johannesburg, South Africa.

Jan 5, 1914

By E. S. Fisher, L. C. R. Alfred

The elastic anisotropy factors, c4,/c6,, c3,/cll, and c12/cl,, for hcp metal crystals vary significantly among the dgferent unalloyed metals. Significant variations with temperature are also found. The effects of elastic anisotropy on the dislocation in an elastic continuum with hexagonal symmetry have been investigated by computing the elasticity factors for the self-energies of dislocations in fourteen different metals at various temperatures where the elastic moduli have been reported. For most of the metals the effects of the orientation of the Burgers vector, dislocation line, and glide plane are small and isotropic conditions can be assumed without significant error. Significant effects of anisotropy are, however, found in Cd, Zn, Co, Tl, Ti, and Zr. The elasticity factors have been applied in the calculations of dislocation line tensions, the repulsive forces between partial dislocations, and the Peierls-Nabarro dislocation widths. It is predicted that the increase in elastic anisotropy with temperature in titanium and zirconium makes edge dislocations with (a), (a + c), and (c) Burgers vectors unstable in basal, pyramidal, and prism planes, respectively. The probability of stacking faults forming by dissociation of Shockley partials in basal planes also decreases with increasing c4,/c6, ratio, when the stacking fault energy is greater than 50 ergs per sq cm. The widths of screw dislocations with b = (a) in titanium and zirconium increase very significantly in prism planes and decrease in basal planes as c4,/c6, increases. The effects of elastic anisotropy on various dislocation properties in cubic crystals have received considerable attention during the past few years. In the case of cubic symmetry the departure from isotropic elasticity depends entirely on the shear modulus ratio, A = 2c4,/(cl, —c12); i.e., the medium is elastically isotropic when A = 1. Foreman1 showed that an increase in the ratio A produces a systematic lowering of the dislocation self-energy for a given orientation and Poisson&apos;s ratio. ~eutonico~, has shown that large anisotropy can have a marked effect on the formation of stacking faults by the splitting of glissile dislocations in (111) planes of fcc and (112) planes of bcc crystals. ~iteK&apos; made similar calculations for (110) planes of bcc metals. Both studies of bcc metals showed that the large A values encountered in the alkali metals tend to reduce the repulsive forces between Shockley partial dislocations. In fcc metals, however, A does not vary over the large range encountered in bcc metals; consequently, the effect of A on the forces between Shockley partials is masked somewhat by the differences in Poisson&apos;s ratio between metals. The effect of A on the line tension of a bowed out pinned dislocation has also been investigated for cubic crystals, first by dewit and Koehler5 and more recent- ly by Head.6 In both cases the line energy model is applied and the core energy is not taken into account, thus making the conclusions somewhat tenuous with regard to the physical interpretation. Nevertheless, the fact that a large A decreases the effective line tension is clearly evident and the tendency for large A to produce conditions that make a straight dislocation unstable (negative line tensions) also seem evident. Head, in fact, shows visual microscopic evidence that stable V-shaped dislocations occur in 0 brasse6 For hcp metals the definition of elastic anisotropy is more complex and, furthermore, significant deviations from an isotropic continuum are found among a number of real hcp metals, especially at higher temperatures. The present work was carried out to survey the effects of elastic anisotropy on the elasticity factors, K, that enter into the calculations of the stress fields around a dislocation core. Some isolated analytical calculations have previously been carried out for several hcp metals but they are restricted in the dislocation orientations and temperature.8&apos;9 The present computations are based on single-crystal elastic moduli that have appeared in the literature and consider various orientations requiring numerical computations. The results are then applied to survey the effects of temperature on the dislocation line tension and dislocation splitting in hcp metals. PROCEDURE Anisotropy Factors. The degree of elastic anisotropy in hcp crystals cannot be described by a single parameter, such as the A ratio in cubic crystals. The following three ratios must be simultaneously equal to unity in order to have an elastically isotropic hexagonal crystal: The magnitudes of these ratios at several temperatures, as computed from the existing data for the elastic moduli of unalloyed hcp metals, are given in Table I. There are no cases of complete elastic isotropy, but the large anisotropy ratios encountered in the cubic alkali metals are also missing. There are, however, several significant differences among the hcp metals, the most notable being the relatively small A and B ratios in zinc and cadmium and the differences in the magnitudes and temperature dependences of A. It has been noted that the temperature dependence of A has a consistent relationship to the occurrence of the hcp — bcc tran~formation. For cadmium, zinc, magnesium, rhenium, and ruthenium, A is less than unity at 4&apos;~ and, with exception for rhenium, decreases with increasing temperature. In the case of rhenium, A has essentially no temperature dependence between 923&apos; and 1123"~, so that it is clear that A does not approach unity at higher temperatures. Cobalt is similar to the above-mentioned group of metals in that it also does

Jan 1, 1969