Search Documents

By Nicholas J. Grant, Olaf Troili, John Chipman

IN recent studies of the factors which affect the rate of desulphurization and its equilibrium, it became apparent that certain concurrent reactions were operative which had a significant effect on desulphurization. This is emphasized in the experiments of Hatch and Chipman1 and of Grant, Kalling, and Chipman' by the slow approach to a final state of equilibrium which is in marked contrast to the initial rapid transfer of sulphur from metal to slag. Since the removal of sulphur is of such profound importance in iron and steelmaking, it appeared necessary to investigate the reactions responsible for this behavior. It is now known that the presence of iron oxide in the slag interferes seriously with the principal reaction of blast-furnace desulphurization: CaO (slag) +-S + C - CaS (slag) + CO [l] The interfering reaction is most simply expressed as: CaS (slag) + 0 = CaO (slag) +-S 121 and a small concentration of oxygen (or FeO) is sufficient to hold a considerable amount of sulphur in the metal. It has been shown by Grant, Kalling, and Chipman2 that the addition of MnO to blast-furnace slag slows the removal of sulphur from the metal. This effect overshadows the contribution of MnO to basicity and is ascribed to its oxidizing power. It will be shown in this paper that SiO, also has sufficient oxidizing power to interfere with blastfurnace desulphurization. This is, of course, only one of its several effects. Primarily it is an acid and therefore reduces the concentration of excess lime. But when silicon is reduced to the metal the oxygen to which it was previously bonded becomes in part available for reaction 2. The proof of this statement is found in the following experiments. Experimental Procedure and Results Utilizing the same procedure and apparatus described by Grant, Kalling, and Chipman' five additional heats were made using slags IV and 11, the starting compositions of which were: slag IV—40 CaO, 10 MgO, 35 SiO,, 15 A1,0,; and slag 11—50 CaO, 10 MgO, 25 SiO,, 15 Al3O3. An important difference between these heats and those previously reported was that silicon to the extent of 1 to 4 pct was added to the present heats whereas the starting silicon content was formerly about 0.2 pct. Table I shows the slag and metal analyses for heats 82 to 87, and Table I1 shows the silicon addi- tions made to the charge. These additions are based on 400 g of metal and 400 g of slag. All heats had 1.65 400pct S charged before the cold slagadditions. The temperature was maintained at 1525°C. Rate of SiO, Reduction: Fig. 1 shows the silicon content of the metal in contact with slag IV at 1525°C as a function of time. Heat 70 from the work of Grant, afunctionKalling,of and Chipman is included as the lowest starting silicon. It will be noted that eeven with 4 pct Si in the starting metal, there is an increase in silicon content with time. Heat 84 is apparently approaching silicon equilibrium very slowly. Heats 70 and 82 with very much lower slowly.starting silicon show a more rapid initial rise in startingsilicon content but do not reach equilibrium during a long holding period. Fig. 2 shows 3 different initial silicon contents for Fig.2shows3differentheats 73 (from Grant, Kalling, and Chipman) 86 and 87, in contact with slag II, the most basic slag. Heat 73 is increasing in silicon with time, whereas heat 87 with an initial silicon content of 3.7 pct shows a decrease with time. Heat 86 shows a very close approach to equilibrium. The rate of transfer of silicon from slag to equilibrium.metal is very slow in all of those heats, even those which are initially far from equilibrium. ____

Jan 1, 1952

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

COLORADO LOCAL SECTION Executive Committee CHARLES A. CHASE, Chairman S. A. IONIDES, Vice-Chairman C. LORIMER COLBURN, Secretary-Treasure, 614 Ideal Bldg., Denver, Colo. F. H. BOSTWICK, W. G. SWART. The annual meeting of the Colorado Local Section of the Institute was held at the Savoy Hotel, Denver, Jan. 15.- The Chairman, Frank Bulkley, presided and made a short address on the work of the Section. The following officers were elected:

Jan 3, 1915

By B. P. Bellport

When tunneling crews set world records in rates of advance by boring up to 403 ft in a single day and 6851 ft in a month, then the age of rapid under- ground excavation is near at hand with its attendant economies. Boring machines excavate tunnels with uniform diameters and smooth walls and only about 5% overbreak compared to 20% overbreak experienced by conventional drill-blast methods. This advantage minimizes the concrete required for lining and because a circular section is more nearly self-supporting there is less of a need for supports before the concrete is placed. In addition, laser beam guidance improves the accuracy of excavation with boring machines. In the first successful application of laser guidance for boring machines in the Navajo Indian Irrigation Project, the final excavation was within 5/8 in. of the established line and grade over a 10.079- ft advance.

Jan 1, 1971

By Ferid Kromer

This paper is the first in a series which will describe geology, mining methods, and production costs of some, of Turkey&apos;s more important minerals. In this paper the economically significant minerals-chromite, meerschaum, and magnesite-of the Tagtepe district are described. The cost data presented are believed by the author to be the first made public on Turkish chromite mining.

Jan 1, 1950

By P. Shahinian, H. H. Smith, M. R. Achter

Crack growth rates are measured at elevated temperature in a resonant fatigue machine from vibration frequency decreases calibrated in terms of crack depth. Crack growth rates in Type 316 stainless steel at 500º and 800°C show a sharp increase with oxygen pressure in an intermediate pressure range and little or no change at high and low pressures. At 500°c, I torr of oxygen reduces the fatigue life by almost a factor of 100 in comparison to that in vacuum and raises the growth rate of shallow cracks by the same At At 800°C the effects are smaller. Changes in slope in the crack growth rate curves are discussed in terms of a model in which rates of surface production and of surface coverage by gas are compared. The use of a calculation method in which the surface exposure time is equal to X/v, where x is the interatomic spacing and v is the growth rate, makes it possible to obtain order of magnitude agreement at 500°C between the observed pressure and the predicted pressure at these slope changes. At 800°C oxidation becomes a .factor and the data cannot be treated by simple adsorption theory. THE decrease in the fatigue life of metals as a function of gas pressure usually follows a stepped curve with virtually all of the decrease concentrated in a sharp drop in a transition zone at intermediate pressures and little or no change at low and high ranges. A number of models, differing in the details of the mechanism, have been offered to explain the shape of the curve. Measurements of crack growth in aluminum as a function of gas pressure by Bradshaw and Wheeler&apos; and Hordon2 demonstrated opportunities for quantitative comparison to evaluate the proposed models. Since comparable data were lacking at high temperatures, in the present work rates of crack propagation were measured in Type 316 stainless steel at 500" and 800°C as a function of oxygen pressure. Choice of this material was dictated by two considerations; it is stiff enough at these elevated temperatures to resonate with the regenerative drive on our fatigue machine and it is known to display a large effect of environment. A new method of calculation is described to predict the gas pressure at the critical point. EXPERIMENTAL PROCEDURE Because of the difficulty of measuring crack depths directly at high temperatures, an indirect method was developed based on the decrease in the resonant frequency with the growth of a crack. A reversed bending, constant amplitude fatigue machine, described previously,3 vibrates a specimen at its resonant frequency, automatically records any changes in it and shuts itself off after it has reached a preset value of frequency decrease. The record of frequency change is used to determine the rate of crack growth. Sheet type specimens of Type 316 stainless steel, Fig. 1, incorporated a sharp, shallow notch to localize the formation of a single crack. After machining, they were annealed in a vacuum of l0-6 torr either at 1066" (lot A) or 871°C (lot B) and then electropolished in an acetic-chromic acid solution. Bending strains were measured at 500" and 800°C by an optical technique4 and reported as total strain without correction for the notch. At 500°C, the 0.141 pct strain was 0.085 pct elastic and the remainder plastic. At 800°C the 0.062 pct strain was all elastic. To convert frequency decrease to crack length, calibration curves were obtained by interrupting the vibration at stated intervals of frequency decrease. The crack depth was measured microscopically at a magnification of X400 and reported as the average of the measurement on each edge. Some specimens were sectioned for crack measurement while others were returned to the machine and fatigued further. There was good agreement between the two methods. Before beginning the vibration, the vacuum chamber was first evacuated cold to 1 x 1O-6 torr, then heated to the operating temperature and held there until the pressure was again reduced to 1 x10-6 torr at which time oxygen was introduced to the desired pressure. In this investigation the vibration frequency was nominally 10 cps and a decrease of 0.6 cps was taken as the failure point. The choice of the frequency decrease to represent failure has no appreciable effect on the fatigue life because the crack is growing very fast at this point.

Jan 1, 1970

By Harrison Everett Ashley

(Pittsburg Meeting, March, 1910.) Slimes are usually defined as all material passing a certain-sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions ; 150-mesh is common practice. The reader of the first two volumes of Richards 1 is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most .economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemical constitution to show the widest possible divergence in physical properties. * Published by permission of the Director of the U. S. Geological Survey. Ore Dressing (1903).

Aug 1, 1910

By Guy R. Johnson

In working brown iron-ore mines on the system employed at Longdale, namely, stoping from the top down, the usual procedure is to drive a succession of upraises from the lowest adit to the highest, or to the top of the deposit, as the case may be. These up-raises are usually driven 120 feet apart., along the strike of the vein,. As the work goes on, they are connected by levels, 10 feet spa* (vertically), and then serve as chutes. A transit is useless in surveying these chutes, and the writer has for several years made use of a hanging compass. The method of using this instrument, described in a former paper (Trans., xx.,.105), embracing as it does the use of a cord and several strips. of wood,

Jan 1, 1894

Jan 2, 1951

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term &apos;&apos;connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;&apos; Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 &apos; to 10&apos; cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10&apos; cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term &apos;&apos;connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;&apos; Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 &apos; to 10&apos; cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10&apos; cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By R. H. Frazier, C. H. Lorig, F. W. Boulger

THERE are both advantages and disadvantages in using semikilled steels in place of killed steels. One advantage of semikilled steels is they provide a higher ingot-to-product yield. This is especially important to shipbuilders in the time of national emergency. By using semikilled steel for hull plates, a greater number of ships can be built from the same ingot tonnage. Consequently, if semikilled steel plates are adequate for the service, the advantage of the higher product yield is of considerable importance. The performance of hull plates is closely associated with the ductile-to-brittle transition temperature, and this, in turn, is strongly dependent on the composition of the steel. A low transition temperature is desirable because it indicates that the steel is less likely to fail at low ambient temperatures. Killed steels are known to have lower transition temperatures than semikilled steels. It is believed that the better qualities of killed steels in this respect are due mainly to the low oxygen contents of the steel. The principal deoxidizers, aluminum, silicon, and manganese, lower the oxygen content. Fundamental studies1-0 have shown that the oxygen content remaining after the addition of one of these three elements is influenced by the residual amounts of the other two present. In the current study, therefore, various amounts of silicon and aluminum were added to steels containing different manganese contents for the purpose of studying the influence of silicon and aluminum on the notched-bar properties of hot-rolled steels. Eleven types of steels were studied. The temperature at which the plates were finish-rolled was care- fully controlled at 1850°F. All plates were rolled to ¾-in. thickness, and tested in the as-rolled condition. The total number of steels prepared in the laboratory for this study was 95. The charge consisting of ingot iron and ferrosilicon equivalent to 0.10 pct Si was melted in a 200-lb induction furnace under an atmosphere of argon to insure low, uniform nitrogen contents. After the charge was melted and the desired temperature was obtained, the melt was partly deoxidized with either silicomanganese or aluminum. Aluminum was used for this purpose in only those steels with very low silicon contents, where the finished steel was to contain some aluminum. This initial deoxidizing addition was made to obtain consistent recoveries of subsequent additions of ferro-manganese, ferrosilicon, and aluminum. Carbon, in the form of graphite, was added, either just prior to tap or to the final aluminum addition. The entire heat of 200 lb was poured directly into a 6x6-in. big-end-up mold. The ingots of semikilled steel were capped with a steel plate. The killed steels, on the other hand, were poured with a hot-top containing 14 pct of the total volume of the ingot. The ingots were processed by heating to 2250°F, followed by forging to slabs 1¾ in. thick and 6 in. wide. After reheating to 2250°F, the slabs were rolled to 0.9-in. gage, using reductions of approximately 1/6 in. per pass. The 0.9-in. thick plates were immediately recharged in a furnace held at 1850°F. After 30 min in the furnace at 1850°F, the plates were rolled to ¾ in. in one pass. Following the final pass, the plates were stacked on edge on a brick floor, with a brick separating one from another, where they were allowed to cool in air. Drillings for chemical analysis were taken from the plates at locations corresponding to the top and bottom of each ingot. Carbon, manganese, silicon, phosphorus, sulfur, and nitrogen contents of each sample were determined. The analysis of each steel was carefully controlled so that the contents of

Jan 1, 1957

By B. D. Cullity

AS methods for measuring fiber textures become more exact, it becomes justifiable to scrutinize an observed pole-density curve for evidence of minor texture components. These are disclosed by minor maxima or abnormally broad major maxima. One possible source of these minor components is twinning of the main component. In cubic metals and alloys, there are two kinds of twins: 1) Annealing twins in face-centered cubic metals. These are reflection twins on {Ill), and they can be expected to be present in recrystallization textures. 2) Deformation twins in body-centered cubic metals. These are shear twins on (112). Although usually formed only by impact, they might conceivably be present in the deformation texture of severely cold-drawn wire. Fortunately, both kinds of twinning lead to the same orientation relationships. It thus becomes possible to prepare a single list of angles between various planes in parent crystal and twin, which is helpful in examining pole-density curves for evidence of twinning in any cubic metal or alloy. Such a list of interplanar angles is given in Table I. This table consists of three parts, corresponding to the three major texture components—<100>, <110>, and <111>-most commonly found in the fiber textures of cubic metals. The table lists the angle between the pole of {hkl}, in either the parent crystal P or the twin T, and the fiber axis <uvu>. The crystals with <uvw> parallel to the wire axis are here

Jan 1, 1959

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By D. O. Ehrenburg

DURING the earlier period of electrical prospecting, the search for orebodies was by far the most important application of this method of geophysical prospecting. In the past few years, however, increasing attention has been paid to the possibilities of this method in the investigation of subsurface structures. Not only have fault zones been located, but attempts have been made to determine the depth to certain strata and thus contouring on some bed which proves to be a good "electrical marker." Many workers have published the results of field tests showing how their particular interpretations have agreed with the actual field conditions, but very few have stated their method of interpretation. Weaver, Hummel and Stefanesco and Schlumberger1 have given a more theoretical discussion of the resistivity methods. Hummel and Stefanesco and Schlumberger have published mathematical solutions for the flow of electricity in a medium involving four layers. In this paper the authors present a solution for the flow of electricity in a medium of any number of horizontal strata. By means of this solution, curves showing the relationship between the apparent resistivity and the electrode spacing can be computed for ideal cases.

Jan 1, 1931

By William P. McConnell

At the dawning of the first century of AIME, mechanical handling of bulk materials was largely confined to movement of grain and light mill products by belt and screw conveyors, but grain handling experience inevitably led to the use of the belt conveyor for coal, ore and other heavier materials. In 1891, the first major U.S. conveyor installation for heavy minerals was completed at the Edison, N.J., plant of the New Jersey & Pennsylvania Concentrating Co. Functionally, this plant revealed its grain elevator heritage. Overlooked at the time of design or, perhaps more accurately, not fully recognized, were the dramatic differences between grain and minerals in both operating conditions of the system and the physical characteristics of the material to be conveyed. This inevitably caused problems, but from the ashes of these problems rose solutions. The Edison plant became a proving ground from which came two significant developments by Thomas Robins-the first conveyor belt designed specifically for impact loading and abrasive materials and the three-roll conveyor idler. As an installation with more than 50 conveyors in widths of 20-30 in. and belt centers of up to 500 ft, the plant was a landmark, for it established the belt conveyor as a vital method of trans- porting heavy, abrasive materials.

Jan 1, 1971

For the first time in its history the Institute will hold a meeting in the State of Arizona. A few years ago Arizona stood third in the copper-producing districts of the United States. Since that time, with the development of porphyry mines, the output has gone up with great rapidity until it not only is the leading district, but its output at the present tune is at the rate of nearly double the Montana output; which now stands second in the list. In connection with this development, most interesting departures have been made in methods of mining, concentration and smelting. Principles of mining and metallurgy of the greatest interest will be covered by papers which will appear in the Bulletin and be presented at Technical Sessions, while ample opportunity &apos;will ,be- afforded for those who go to the meeting to see all the points of interest to them. In addition, members will be well rewarded by the marvelous natural features to be seen on the trip, including the petrified forests, the cliff dwellings on the Apache Trail and the Grand Canyon of Arizona. It is planned to start the special train from New York, but members and guests may join the special at other points en route as indicated by the following schedule: ITINERARY Thursday; September 14th, Lv New York Grand Central Terminal 5.30 p.m. Dinner in dining car, a la carte

Jan 9, 1916

Discussion of the papers of Benjamin Talbot. E. A. Beck, Emil Gathmann, Sir Robert A. Hadfield, and P. H. Dudley, presented at the New York Meeting, February, 1913, and printed in this Bulletin (No. 76, April, 1913). CHAIRMAN JAMES F. KEMP :-I call upon Prof. Albert Sauveur to open the general discussion on the subject of sound steel ingots. ALBERT SAUVEUR, Cambridge, Mass. :-I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain some very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my Views.

Jan 4, 1913

ASSETS CAPITAL ASSETS Equity in United Engineering Society&apos;s Land and Buildings $486,792 79 Library 40,000 00 $526,792 79 INVESTMENTS Jas Douglas Fund-Schedule #2 $ 99,966 40 Life Membership Fund-Schedule #3 9,415 63 R W Hunt Medal Fund-Schedule #4 7,489 09 116,871 12 INVENTORIES Paper Account .305 10

Jan 1, 1923

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co. purchased the first pumpcrete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms.

Jan 4, 1954