Search Documents

By Thomas H. Clagett

ThE Pocahontas coal field comprises the area in Tazewell County, Va. and Mcrcer and McDowell counties, W. Va., in which Nos. 3 and 4, Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305 111.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, to which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks of bone, cach from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 2.5 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficieiltly well defined to exert an influence on the mining is rare. Overlying strata arc slates, shales, and sandstones, the sandstones predominating, extending from 30 to 1000 ft. above No. 3 seam. The strata directly above the draw slate of No. 3 seam, or "black rash" of No. 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the.

Jan 1, 1923

By Thomas H. Clagett

ThE Pocahontas coal field comprises the area in Tazewell County, Va. and Mcrcer and McDowell counties, W. Va., in which Nos. 3 and 4, Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305 111.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, to which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks of bone, cach from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 2.5 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficieiltly well defined to exert an influence on the mining is rare. Overlying strata arc slates, shales, and sandstones, the sandstones predominating, extending from 30 to 1000 ft. above No. 3 seam. The strata directly above the draw slate of No. 3 seam, or "black rash" of No. 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the.

Jan 1, 1923

By Russell S. Sage

THE electric motor has steadily replaced the steam and air engine for use in mine hoists, until today a new installation with other than electric drive is a rarity. Much existing steam-driven equipment has been changed over to electric drive. Driving power has grown in capacity since the initial electric unit rated 10 hp installed at Aspen, Colorado, in 1888, to 3000 hp and 4000 hp in the United States, and to 5500 hp in Canada-the largest in the Western Hemisphere. Electric installations now total in the thousands of units, a growth largely made possible by the development of large central electric-power stations and the extension of electric-power service to more mining areas.

Jan 1, 1949

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. INTRODUCTION Buchans is 5 miles north of Red Indian Lake, in Central Newfound- land, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller- town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Ch, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By W. Vickers

Single-point rotating cantilever fatigue tests have been carried out at 550" to 650°C on beryllium produced by a variety of fabrication routes. All the specimens gave similar plots of stress against number of cycles to failure but failure occurred at a lower stress range in the hot-pressed material than in the extruded material. A discontinuity or "kink" appears to exist in the curves and this is considered. A true endurance limit was not evident up to 10 cycles. When Brush hot-pressed warm-extruded beryllium was tested at 600oC a relationship where Nf = number of cycles to failure, ?ep = plastic strain range, and c = constant, was shown to be applicable for values of ?ep > 6.3 x 10-4. Further for this moterial and temperature and for frequencies between 150 and 4500 cycles per min, the variation of number of cycles to failure with frequency obeyed the expression N = Af0.44 where N =number of cycles to failure, f = frequency, and A = constant. Examination of the fracture surfaces indicated that they were generally intergranular and in all cases the higher the stress the more irregular was the fracture. Microexamination has shown that grain boundary cavities and fine intergranular cracks were associated with the fractures. REVERSING or cyclic stresses set up in fuel elements can lead to failure by fatigue. Fatigue stresses may be developed by instability of the fuel element in the coolant flow leading to rattling against the channel wall or fin vibration. Thermal cycling also sets up reversing stresses due to differential expansion of fuel and can. Fatigue resistance is of some importance therefore in the evaluation of canning materials. At the time the work described in this paper was initiated, beryllium was being considered for the can and endcaps of an advanced gas-cooled reactor fuel element. With this in mind, beryllium obtained from different manufacturing routes was tested on single-point rotating cantilever fatigue machines at temperatures the same as those envisaged in the reactor to obtain appropriate fatigue data. The results obtained indicated a discontinuity in the S-N curves coinciding with the yield stress in the specimens. Although in some cases the data is insufficient to warrant a detailed quantitative analysis, a qualitative analysis of this effect was thought to be justified. 1) EXPERIMENTAL DETAILS The materials used are given in Table I together with the production route and available analyses. The specimen shape is shown in Fig. 1. The fatigue specimens were machined slightly oversize, after which they were given a stress-relieving anneal of 1 hr at '750° C in vacuum. This was followed by an etch in sulfuric-phosphoric-chromic acid mixture down to the finished dimensions given in Fig. 1. Etching served to remove the interference colored oxide film formed on the surface during annealing and very small recrystallized surface grains too. The specimen was mounted in the grips of a cantilever machine and rotated inside a furnace controlled at the testing temperature. The specimen was loaded in increments as the speed was increased until the required load was applied at 5000 cycles per min. A revolution counter was used to record the total number of cycles.

Jan 1, 1964

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer .pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks.

Jan 1, 1933

By L. E. PORTNER

INCREASING military demands on the petroleum industry have brought into bold relief the crude-oil reserves now available to meet combined military and civilian demands, emphasizing the necessity for a greater efficiency in recovery from what has been discovered than ever before, particularly in light of the absence of new discoveries. This situation-and the fact that the industry, as well as members of the Government charged with governing oil production, desire to meet all crude-oil demands made of the industry with the least loss in tangible reserves through production practices-paves the way for increasing application of sound principles of production engineering and conservation.

Jan 1, 1944

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By Charles W. Frey

COMPRESSED air is one of the most useful tools that the mine operator has at his disposal. It is clean, nontoxic, easily handled, and can be distributed anywhere that a man can drag a length of rubber hose. Without it a great deal of drilling would still be a laborious hand process, and although the John Henry of legendary fame could beat a mechanical drill, John Henrys are few and far between, and in the long run the air drill is the victor. As a general rule, horizontal compressors are lubricated by mechanical lubricators, which furnish oil to the cylinder walls, whereas vertical units are splash lubricated. In most horizontal machines oil is introduced at the top center of the piston, from which point it can run down and lubricate the rest of the piston. Some large units introduce oil at more than one point on the cylinder wall, the necessity for this and the number of points of introduction depending upon the size of the cylinder.

Jan 1, 1938

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.' It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins' solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion' is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

By E. Martinez

Samples of chrysocolla, a hydrated copper silicate, from several sources were submitted to differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). Pure samples of chrysocolla are difficult to obtain, but comparison of the thermograms revealed that certain reactions occurred in all the samples and it is believed that these are due to chrysocolla. Endothermic reactions occurred at 50' to 175°C, 350° to 650°C, and 980° to 1100°C each of which caused a weight loss. The first was due to loss of absorbed water, the second to a dehydroxyla-tion, and the last to conversion of cupric oxide to cuprous oxide. In addition, two exotherms were detected at 685° to 695°C and 935° to 950°C. Infrared spectra of heated samples indicated the exotherms were due to changes in the Si-O bonds leading to the formation of cristobalite. The results suggest that thermoanalysis may be a more sensitive and reliable method for detection and identification of chrysocolla than X-ray diffraction, infrared spectroscopy, or optical techniques. The recovery of copper from oxide ores has been the subject of much research in recent years. One of the principal oxide copper minerals is chrysocolla, a hydrated copper silicate. The information available indicates that it has widely varying properties depending on the origin of the sample. Chrysocolla usually is found associated with cuprite, malachite, azurite, and native copper. Most of these other minerals are recoverable by present day flotation practice, but chrysocolla is lost in the tailings.1,2 Reagent combinations that are successful in laboratory chrysocolla flotation with ore from one source have been found to be ineffective with another. 3 The copper segregation process offers an altemative to beneficiation of oxide copper ores.4'5 The process is of particular interest in processing ores that cannot be treated by conventional hydrometal-lurgical methods because of high acid consumption.6 Fuller understanding of the properties of chryso- colla may prove of value in the search for improvements in both the flotation and segregation processes. Chrysocolla samples from Arizona, Nevada, Chile, Australia, and South Africa were studied by differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). In addition, a sample from Miami, Ariz., was submitted to X-ray diffraction, infrared spectrophotometry, and surface area determination. EQUlPMENT Differential thermal analysis (DTA) detects, amplifies, and records exothermic-endothermic reactions occurring in a sample as its temperature is raised at a constant rate, usually 10°C per minute. A unit made by the Robert L. Stone Co. was used in this study. The tests can be run if desired with a gas streaming through the sample. A thermobalance records weight losses or gains in a sample as its temperature is raised at a uniform rate. The gravimetric analyses (TGA) were run on a Chevenard thermobalance converted electronically for graphic recording. A heating rate of 5°C per minute up to 1100°C was used in these tests. A Perkin Elmer Infrared Spectrophotometer, Model 221, was used with sodium chloride optics obtaining IR spectra in the 2 to 15 region. A pressed pellet technique with potassium bromide was used in preparing the samples. DESCRIPTION OF SAMPLES Chrysocolla is found in the oxidation zones of copper deposits commonly associated with malachite, azurite, and limonite. It is described as varying in composition and in color from bluish green to brown or black. Inclusions of other minerals are usual so chemical analysis of chrysocolla samples may be suspect. However, it is considered by many to be a solid solution of CuO, SiO2 and H2O with a general formula of CuO.SiO2.2H2O or 2CuO.2SiO2. 3H20. Chukhrov7 has described a sample from the Urals as CU3,5(OH)2 (A1Si3) O10.nH2O and stated that chrysocolla is a montmorillonite-type mineral. On the basis of X-ray analyses, DTA, and infrared spectra of chrysocolla from the Inspiration Mine, Ariz., Sun8 concluded that there was no substantial evidence to classify it as a montmorillonite mineral. Chrysocolla samples from many sources throughout the world were used in this investigation. The following is a brief description of each:

Jan 1, 1963

By Thomas Elliott

It is now clearly evident that 1963 is witnessing a record year for prospecting and exploration in British Columbia and Yukon Territory, as substantiated by the following facts: ? About 60 large mining companies and many smaller ones are active in the search for new ore deposits. ? More than 500 prospectors and exploration geologists have been in the field this season. ? It is estimated that $10 million has been spent this year on the search for new ore deposits. ? Claim staking in B. C. to July 31, totalling 14,250, is up 2000 over 1962. ? Helicopter companies report a record total of 25 aircraft chartered to mining groups, with additional numbers used in oil-gas exploration. ? Leading assayers state that business with the industry is double that of the previous year. ? Diamond drillers report an increase of approximately 25% in the amount of contracts now on hand. The question is often asked, "Why is mining so active in Canada's Pacific Northwest?"

Jan 12, 1963

By E. C. W. Perryman

On electropolishing, high-purity Cu-Sn and Cu-Sn-P alloys with more than 5 to 9 pct Sn were found to contain many grain boundaries with a ridge-and-furrow profile. The effect was not eliminated by solution treatment and was present at the new boundaries in recrystallized material. It could be produced by diffusing tin into the 3 pct Sn alloy and it is concluded that the effect is due to enrichment of certain boundaries in tin, or possibly in an impurity present in the tin, in solid solution. IN the hot working of tin bronzes, especially those with moderately high tin contents, considerable difficulty is frequently encountered from intercrystal-line weakness, which results in cracking at the edges in sheet on strip rolling and in the unsupported regions of the rod in rod rolling.' These difficulties are not at all pronounced with up to 3 pct Sn, but at 5 pct Sn impose serious limitations and at higher tin contents, especially if the phosphorus content is also high, they may become very severe. In some work carried out at the laboratories of The British Non-Ferrous Metals Research Association it was found that a notable lack of ductility in tension at elevated temperatures, associated with intercrystal-line failure, was characteristic of tin bronzes even of relatively high purity. That the intercrystalline fracture is not due to a brittle or molten impurity phase at the grain boundaries was shown by the fact that the temperature at which intercrystalline fracture first occurred decreased with decrease of rate of straining. Tensile tests on some commercial tin bronzes, reported by Goetzel,² show a similar fall in ductility with increasing temperature. As no visual evidence had been obtained showing that the grain boundaries of the tin bronzes were different from those in copper, a more detailed microscopical examination was carried out, and the results of this are given in the present report. Several workers"' have observed that electrolytic polishing is a powerful tool for detecting small amounts of a second phase and in particular for detecting high solute concentrations, "equilibrium segregation," at grain boundaries. Since it had been found that the suggested solutions for electropolishing bronze and the standard solutions for brass and copper did not give satisfactory results it was first necessary to find a suitable electropolishing solution.' Experimental Procedure Materials Used: The cast and wrought materials used for this work were the same as those used for the mechanical tests referred to above. They comprised 3, 6, and 9 pct Sn alloys without phosphorus and the same three basic alloys with 0.03 and 0.4 pct P. A 5 pct Sn alloy without phosphorus, of similar purity, was also examined. The basis materials were Chempur tin, high purity 15 pct phosphor-copper and cathode copper, and spectrographic analyses are given in Table I. Treatment: The cathode copper was first melted under charcoal, degassed by plunging marble chips beneath the surface, and cast through a coal gas flame into sand molds to produce a number of small ingots which after machining were of a suitable size for subsequent vacuum melting. Chill cast bars of the alloys, approximately 1¼ in. in diameter, were then made by melting and casting in vacuo, the tern-

Jan 1, 1954

By J. David Lowell

For his contributions to the field of mining geology, a striking example being his brilliant inte.rpretation of the complex geologic history of the San Manuel District (Pinal County, Arizona) which resulted in the discovery of the Kalamazoo orebody, and for his lecture, "Copper Resources in 1970." On a low desert ridge six miles south of Cairo lie the remains of the world's earliest known mining town, Maadi of predynastic Egypt. Copper artifacts, including ingots and an ax head which was spoiled in casting, indicate that copper ore was smelted in Maadi, and radiocarbon dating has placed the activity at least as early as 3300 B.C. This is the oldest documented date for the use of smelted copper, the first industrial metal used by man. Copper was mined and smelted almost as early in Asia Minor and on the island of Cyprus, but the greatest development of the budding copper industry was in Egypt, where specific historical records show that about 10,000 tons of copper metal were produced in the period from 1850-1580 B.C. Contrast this production of 35 tons per year with the present world production of about 7 million tpy. Evolution of the Copper Industry The copper ore mined by the ancients was high grade, and the copper produced was expensive. The copper industry began with narrow high-grade veins, but has evolved to the point where massive earth-moving equipment can be operated in huge, low-grade open pits. Indian pits dug before 3000 B.C. in the Lake Superior district were in ore which averaged 15% Cu. His- torical research done by Arthur Brant has shown that copper cost in the Middle East in 1840 B.C. in terms of 1970 labor dollars was about $25 per lb. The copper mined in northern Europe in 1540 in the time of Georgius Agricola averaged about 8% Cu, and the cost in 1970 labor dollars was about $10 per lb. Average ore grade had dropped to about 6% Cu in 1890, and the cost of copper in the U.S. in 1970 dollars was about 45¢ per lb. Butte, Mont., was a good example of the efficiently operated vein mines of this time. In 1906, Daniel Jackling made a dramatic entrance into the copper scene with the Bingham Canyon open-pit copper mine and proved that more profit was possible mining 2% porphyry copper ore on a

Jan 1, 1971

THERE can be little doubt in the mind of anyone of the great interest which has been provoked in the mining and petroleum industry by the com-paratively new geophysical methods of prospecting, after the sessions at this year's meeting of the Institute. Not only were the sessions very well attended but every¬one seemed most attentive. Although the discussion was somewhat limited in general, that may well be at-tributed to the newness of the subject. Two sessions on this subject were planned originally, but these gave insufficient time for the presentation of all the papers prepared and a third session was abso-lutely necessary. The first meeting dealt entirely with the gravity methods and was completed in the scheduled time owing to the fact that but two of the five papers listed were read. The second session was devoted to magnetic and electrical methods, the completion of which had to be carried over into the third period of geophysics. The first session on geophysical prospecting, and in-cidentally the first scheduled Institute meeting devoted entirely to this subject, was most appropriately opened by E. L. DeGolyer, the chairman of the session. It was through the efforts of Mr. DeGolyer that the first gravity work, as applied to prospecting, was under-taken in this country. Again most appropriately, the first paper presented was given by Donald C. Barton, who carried on the first work with the Eötvös torsion balance in America and aided materially in its development. A subject, the theory of which is so difficult to understand as it is generally presented, was so clearly illustrated and ex-plained by the speaker that even a novice could grasp the fundamentals. Dr. Barton, in showing actual re-sults obtained in torsion balance surveys with the in-terpretation of the sane and later drilling records, was free in stating that there are many limitations to the field in which this and the other geophysical instruments may be successfully employed. This paper called for considerable discussion relative to the application of the torsion balance to gravity surveys over various types of structures. During the course of this discus-sion a very important point was emphasized by the chairman, namely, that for successful application of any or all of the scientific methods of prospecting, a back-ground of experience is absolutely necessary to serve as a basis for further work. This can only be secured by contributions from the results of actual prospecting work.

Jan 3, 1928

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By C. D. Stahl, R. Sandrea

This investigation was made to evaluate the comparative effects of the viscosity and the phase behavior of the buffer fluid in the composite solvent displacement of Bradford crude from waterflooded sandstone cores. Buffer slugs of propane, naphtha and other refined hydrocarbons exbihiting increasingly favorable viscosity ratios and decreasing solubility relationships, respectively, with Bradford crude, were used in long Berea sandstone cores. The secondary slug was isopropyl alcohol. The results indicate that higher oil recoveries are obtained for increasingly favorable phase relationships even when these are accompanied by unfavorable viscosity ratios within the range studied. Moreover, when propane is used as a buffer slug with an adverse viscosity ratio of 36, it gives higher oil recoveries than at a similar size slug of an any1 alcohol having a viscosity ratio of 1.09. The investigation was extended to the study of the effect of flooding rate on oil recovery. Residual Bradford crude was displaced from a 6-ft Berea sandstone core at rates varying from 0.3 to 30 ft/ day. The results show that as flooding rates were increased above or decreased below a minimum range of 1 to 2 ft /day, displacement efficiency increased considerably. INTRODUCTION In recent years, the alcohol slug process as a means of tertiary recovery has been the subject of many investigations. Gatlin and Slobod showed the advantages of the combination solvent slugs over the previous single-slug process.1 The combination slugs require less total slug material to obtain similar oil recoveries. The basic combination process involves injecting a primary or buffer solvent which is preferentially oleophilic, followed in turn by a water-driven slug of isopropyl alcohol. This procedure ensures that the buffer slug, which is miscible only with the reservoir oil, displaces and replaces the oil and is in turn displaced, together with the water, by the isopropyl alcohol slug miscible with both fluids. Likewise, for those reservoir oils that show some degree of phase incompatibility with isopropyl alcohol, as does Bradford crude, a proper buffer solvent can artificially make the alcohol process technically feasible. From an economic standpoint, propane or LPG would be the most appropriate primary solvent to be used in the field; however, Taber, et a12 have indicated that the alcohol process becomes highly inefficient in the displacement of light hydrocarbons because of the entrapment of these hydrocarbons during the stabilized bank formation. Moreover, since materials such as propane have such low viscosities, adverse viscosity ratios with most reservoir oils would be penerated, thereby possibly further reducing the efficiency of the buffer solvent. This paper presents the results of an experimental study of the comparative effects of viscosity ratio and phase relationships on the displacement efficiency of Bradford crude by means of dual solvents. The work was extended to include the effect of flooding rate on oil recovery. Rates within the range of field and laboratory values were used. EXPERIMENTAL PROCEDURE APPARATUS The porous media used in this study consisted of two 10-ft and one 6-ft Berea sandstone cores, 3-in. in diameter. These were cast in galvanized steel pipe of 31/2-in. ID and the annulus was filled with Armstrong cement. The 10-ft cores were assembled by connecting two 5-ft units, which were joined together by 8-in. steel flanges fitted to the pipe. Intimate contact between the two sections was obtained by inserting a thin disk of the same sandstone between the core faces. The outlet and inlet ends of the cores were covered with threaded pipe caps. The injected fluid was gravity fed to two variable-rate positive-displacement pumps. The fluids were filtered before entering the core and the effluent was collected in an automatic fraction collector and

Jan 1, 1966

By R. E. Ogilvie, A. R. Kaufmann, S. H. Gelles

The solid-solubility limits of iron in beryllium were determined between 850o and 1200oC by analysis of differential type multiphase diffusion couples, using an X-ray absorption technique. The maximum value of the solubility limit was found to be 0.92 ± 0.02 at. pct (5.46 wt pet) at the eutectic temperature 1225°C. The solubilities of nickel and beryllium were determined between 900°and 1200°C by the same technique and the maximum solubility was found to be 4.93 + 0.01 at. pct (25.2 wt pet) at the eutectoid temperature, 1065°C. A previously unreported high-temperature phase which decomposes eutectoidally at 1065 °C was found to exist in the beryllium-nickel system at a composition of approximately 8 at. pct Ni (36 wt pet) by diffision-couple analysis. The presence of this phase was confirmed by thermal analysis and metallo-graphic analysis of the structure resulting from the eutectoid decomposition. G. V. Raynor1 has treated the solid solubilities of some of the elements in beryllium on the basis of the "Hume-Rothery" rules2 which have been modified to include ionic size and ionic distortion effects. It was predicted that the solubility of iron and nickel in beryllium should be slightly less than that of copper. The lowering of the solubility, according to Raynor, is due to a more unfavorable relative valency effect and an ionic size effect. Kaufmann and corzine3 have compiled data on the solubilities of elements in beryllium and have discussed them in the light of the Raynor paper. These authors feel that, because the elements having the greatest solubility in beryllium systematically fall in the Group VIII and IB Columns of the periodic table, the electronic structure greatly influences the maximum solid solubility of elements in beryllium. The solubility of iron in beryllium was determined by Teitel and cohen4 as part of the study of the beryllium-iron phase diagram. The determination was carried out by X-ray and thermal analysis and according to the phase diagram presented, the maximum solubility of iron in beryllium is 0.41 at. pct (2.5 wt pct) at 1225oC. However, it is estimated that the uncertainty in the position of the a-beryllium primary solid-solution boundary is about 0.5 at. pct (3wtpct). Losana and Goria3 in studying the beryllium-nickel phase diagram, determined the solid solubility of nickel in beryllium by thermal analysis. They found the maximum solubility to be between 1.65 and 2.65 at. pct (10 to 15 wt pct) at 1240°C. This value decreased rapidly with decreasing temperature. In determining approximate ranges of solubilities for different elements in beryllium, Kaufmann, et al,8 reported a value of between 1.3 and 1.7 at. pct (7.9 to 10.1 wt pct) for the solubility of nickel in beryllium. The value was obtained by metallographic examination of quenched alloys and lattice-parameter measurements. However, the authors also noted a single-phase structure for a 1.7 at. pct Ni alloy (10 wt pct) on cooling from the liquid. This would indicate a higher solubility range than was reported. ~isch,&apos; in his X-ray studies of beryllium-copper, beryllium-nickel, and beryllium-iron intermetallic compounds, reports the disappearance of a second phase (Ni,Be2) in the beryllium primary solid solution at approximately 4 at. pct (20 wt pct). THEORY The analysis of concentration gradients in diffusion couples has proven to be a useful tool in determining phase equilibria.8-14 In this particular study the diffusion couples were chosen to straddle the expected composition range of the phase boundary, then heat treated at a given temperature and the concentration gradient evaluated. The composition of the phase boundary for a given temperature appears at a point of discontinuity of the composition gradient. Examples of typical phase diagrams and the concentration gradients which should be found in such systems are shown in Fig. 1. In the present work, gradients of the form of Fig. l(c) were obtained in diffusion couples made of pure beryllium and two-phase alloys of beryllium with either iron or nickel. The composition at the point where the gradient becomes discontinuous, Cs, corresponds to the solubility limit of either iron or nickel in beryllium. The analysis of the concentration gradients was carried out by an X-ra absorption method developed and applied by Ogilvie and later used by Moll13 and Hilliard.l4 It depends on the fact that the absorption of X-rays by matter is determined by the concentration and type of the various atomic species present. The relationship for the intensity, I, of a monochro-

Jan 1, 1960

By M. Nicholas, D. M. Poole

The diameters of sessile drops have been found to increase linearly with time in five reacting binary metal systems. The spreading rates of the drops are markedly dependent on temperature and on prior alloying of the solid with the lower melting point metal, hut are independent of the drop volume, wetting atruosphere , solid-surface roughness, and prior alloying of the drop with the substrate metal. A mechanism has been suggested that relates the linear-spreading rate to lateral diffusion of the liquid-metal atoms into the solid at the drop edge. An Arrhenius- type equation has been derived that describes the temperature dependence 0) the spreading rate, and although the agreement between the actual and the predicted pre-exponen-tial terms is poor that between the activation energies is excellent and the variation in the spreading rate of copper on Ni-Cu alloys produced by different extents of alloying can be predicted with considerable accuracy. CHEMICAL interactions frequently change the wetting behavior of solid-liquid systems causing, for example, "secondary spreading1 of sessile drops beyond the size defined by the surface and interfacial tensions of the unreacted components. The kinetics of the contact-angle decreases associated with this spreading are similar for many systems, but few studies have been made with the objective of determining whether the similarities are a reflection of a common mechanism. Some workers2,3 have assumed the secondary spreading is controlled by changes in the liquid surface and liquid-solid interfacial tensions and hence by the composition of the liquid, and contact-angle changes measured by the vertical-plate technique have been used to follow the course of liquid-solid chemical reactions.4 Other processes that have been invoked to explain these time-dependent changes in specific systems include the removal of adsorbed gas from the liquid-solid interface.5 penetration of containment layers on the solid Surface,6 interdiffusion,1,7 reori-entation of the solid surface into a wettable configuration: vapor-phase transport of the liquid onto the solid in advance of the drop,9 and, from vertical-plate studies. capillary flow between oxide layers and the solid surface.10 One of the reasons for the profuseness of these suggestions may be the complexity of the contact-angle change kinetics. However, in an analysis of secondary spreading gold and copper on UC,11 it was found that the diameter of the contact area between the sessile drop and the solid surface showed a simple linear increase with time although contact-angle changes were more complex. To check whether the linearity was merely fortuitous! additional exploratory work was conducted with four reacting metal-metal systems: Au on Ni. Cu on Ni, Cu on Fe, and Ag on Au. Linear spreading was observed in every case even though the kinetics of the contact-angle changes were complex. A further detailed study of the kinetics of linear spreading of five reacting metal-metal systems has been made with the object of determining the mechanism involved. The influence of variables such as temperature, drop volume. and the initial composition of the drop on the linear-spreading rate has been measured and compared with those predicted by a number of possible mechanisms. The systems employed in this study (Cu and Au on Ni and Pt, and Ag on Au) were selected because of the availability of potentially relevant chemical and physical property data. the simplicity of their phase diagrams at the wetting temperatures, and the ease of experimentation. EXPERIMENTAL TECHNIQUES The purities of the metals used in the study were: copper, 99.9 pct; gold. 99.96 pct; nickel, 99.2 pct; platinum 99.99 pct; and silver, 99.999 pct. The wetting tests were performed in a split tantalum tube vacuum resistance furnace of a conventional design. The furnace element was held vertically and was 1 $ in. in diam and 6 in, long. Viewing ports were provided in the water-cooled chamber to enable the specimens to be observed in both the horizontal and vertical planes. The temperature in the hot zone of the furnace could be held at 1500" i 5°C for an indefinite time. The surfaces of the solid-plaque metals were ground flat on Microcut paper and both the sessile drop and substrate metals were ultrasonically cleaned in methyl alcohol prior to their insertion in the furnace. After loading, the furnace was pumped down to a pressure of 2 x 10-5 mm of mercury and degassed for 30 min at 900° to 950°C. The temperature was then increased at more than 100°C per min to that used in the wetting test. The vacuum at the wetting temperature was better than 5 x 10-5 mm of mercury. Dewetting and retraction of the drop on cooling did not occur and the contact-area diameters, therefore, were measured after solidification with a vernier traveling microscope. The diameters quoted later are arithmetic means of ten measurements. The standard error of the mean never exceeded 3 pct and was often less than 1 pct.

Jan 1, 1967