Search Documents

By K. V. S. Sastry

INTRODUCTION Flotation is by far the most important unit operation of mineral processing. Most of the common base metals are produced from flotation concentrates of metal sulfides. Flotation is proving to be a valuable process for producing non-metallic minerals such as ceramic oxides, silicates, clays and phosphate fertilizers. All these fltation separations are carried out on materials which are predominantly in the 10 to 100 micronssize range. The present practice of flotation circuits for the production of large tonnages of metallic and non-metallic mineral concentrates is fairly well understood, developed, and standardized. Two kinds of problems are encountered (1, 2) with fine particles smaller than 10 microns. First is the interference of the fine particles with the flotation of the coarser particles and the second is the poor flotation behavior of fine particles. In general, these problems are handled either by eliminating, minimizing, or ignoring the fines in the flotation circuit feed. In recent years, however, a considerable number of experimental and theoretical studies have been carried out to understand the flotation behavior of fine particulates. This literature is summarized in four review papers (2-5). Application of the conventional flotation techniques for the separation of mineral fines is known to be uneconomical, and to present several scientific and technological problems (1-5). The objective of this presentation is to examine the flotation behavior of fine particles in terms of their physical-chemical properties and to review the potential techniques of fine particle flotation. Specific reference to the problem areas and research needs will also be included in the discussion.

Jan 1, 1979

By R. A. Vandermeer, Paul Gordon

On the basis of a unified concept, theoretical erPressions for grain boundary migration in recrys-tallization are derzved for impurity-controlled and impurity-independent migration. The expression in the former case is analogous to that Previously derived by Lucke and Detert, and in the latter is shown to be equivalent to that usually obtained on the basis of absolute reaction rate theory. The equations are tested with quantitative experimental data for boundary migration obtained for the recrystallization of poly crystalline zone-refined alumimnz and for binary "alloys" of this aluminum with 0.00021, 0.00043, 0.0017, 0.0034, 0.0068, 0.0124, and 0.0256 at. pct Cu, respectively. All the essential characteristics of the e@erimentally determined boundary migration rates check both qualitatively ard quantitatively with the predictions of the theoretical equations. THE rates of transformations are customarily analyzed phenomenologically in terms of the two component rates—N, the rate of nucleation and, G, the rate of growth of the nuclei. The scientific aim of both theory and experiment is to describe the fundamental atomic phemmena involved in these two component processes with the hope that parameters calculated from theoretical equations will check those found experimentally. In solid state transformations, the theoretical and experimental problems are both generally of almost prohibitive complexity, for in addition to changes in composition and in such properties as density which may accompany transformations in amorphous, nonrigid materials, transformations in crystalline substances also involve structural changes, crystal reorientations, and the development of stresses. In studying such transformations it thus becomes; highly desirable, if not essential, to focus on a transformation and a set of conditions which minimize the number of active variables. This principle has been applied with considerable success by Cohen and his associates' in their evaluation of nucleation theories using the martensite transformation as the basis of study. A similar possibility exists for the evaluation of growth theories by the use of recrystallization after cold-deforming. If an unalloyed metal is employed as the subject of investigation, the recrystallization transformation involves basically only a change in strain-conditions and orientations. In spite of this possible simplilfication, however, until recently little quantitative success has attended attempts to correlate recrystal1ization parameters measured experimentally with those calculated theoretically. It seems highly probable that this lack of success may be attributed, both in the experimental and theoretical treatments, to one or more of the following factors: a) conditions have usually been studied under which apparently* both nucleation and growth are active;

Jan 1, 1962

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By K. D. Hester, A. C. Anderson

The Elliot Lake uranium deposits are contained in a pebble conglomerate which is similar throughout the basin. This paper compares the solid-liquid separation circuits of two nominal 3000 T/d acid leach uranium concentrates treating Elliot Lake ore. One concentrator employed rotary vacuum drum filtration for solids removal and washing, the .other used counter current decantation in torque arm thickeners. Capital and operating costs, operation and maintenance, and metallurgical performance of the two solution recovery methods are compared and contrasted. A recent development, removal of the sand fraction ahead of C.C.D. and separate sand washing in hydraulic cyclones, is also discussed.

Jan 1, 1973

By O. J. C. Runnals

The intermetallic compounds NpAl2, NpAl3, and NpAl have been prepared, and examined by X-ray diffraction methods. The compounds are isostructural with the corresponding U-Al compounds. NpAl3 is face-centered cubic with a = 7.785A and has the MgCu2 structure. NpAl is simple cubic with a = 4.2624 and has the AuCU3 structure. NpAl4 is body-centered orthorhombic with a = 4.428, b = 6.268, and c = 13.71A. The published description for the atomic positions in UAl, applies also to NpAl4 THE U-Al system has been examined by Gordon and Kaufmann.1 They identified the following intermetallic compounds: UAI2, UAl3, and a third, tentatively identified as UAl5. A structure analysis of the latter compound by Borie2 proved that the formula UAl4 was more consistent with the X-ray data. The crystal structures of UAl2 and UA have been reported by Rundle and Wilson.3 UAl2 was found to be isostructural with MgCu. The atomic positions in the simple cubic UA1, cell were found similar to those in the AuCu3 structure. Three analogous compounds exist in the binary system Np-Al. X-ray data for the compounds NpAl2, NpAl3, and NpAl4 are reported below. The neptunium used in the investigation was supplied through the courtesy of the Argonne National Laboratory as neptunium (V) nitrate. It was stated to have a radioactive content of 99.25 pct Np237. The impurity limits had been established by a spectrographic analysis given in Table I. Any titanium, boron, or bismuth impurity should be effectively removed during the fluorination of NpO2 to NpF4, and sodium, lithium, magnesium or strontium during the alloying procedure. The oxalate ignition technique, described by Westrum for the preparation of finely-divided reactive PuO2, was used.The neptunium (V) nitrate solution, containing 100 mg Np, was evaporated to dryness on oxalic acid crystals. The resulting oxalate was calcined to NpO, by heating in platinum at 650°C for 2 hr. An equimolar mixture of anhydrous hydrogen fluoride and purified hydrogen was passed over the NpO2 for 2 hr at 500°C. According to Fried and Davidson" the above fluorination conditions should produce the purple-black fluoride, NpF3 However, the light-green product showed only NpF4 lines on an X-ray diffraction pattern and contained only an estimated 5 pct of finely dispersed black NpF3 particles on microscopic examination. NpAl3: An intimate mixture of 50 mg of neptunium fluoride and aluminum powder (99.99 pct pure, —28 to $60 mesh) was heated to 900°C in a BeO crucible in vacuum by a tungsten coil for 2 hr, to allow the following reaction to proceed: NPF4 + 7Al + NpAl, + 4AlF. [1] The formation and sublimation of aluminum mono-fluoride in this system was verified from an X-ray diffraction analysis of the sublimate. The diffraction pattern was similar to one obtained in the aluminum reduction of UF4 to UF3,6 showing both Al and AlF3 lines. The resulting alloy was sintered at 1100°C for 1 hr. A powdered specimen of the crystalline product was sealed in a thin-walled quartz capillary for X-ray examination. The photograph was taken on a 14.32 cm General Electric powder diffraction camera, using filtered copper radiation. The films were calibrated in terms of a NaCl standard pattern. The wavelengths used in the calculations were 1.5418A for Cu K and 1.5405A for Cu K The powder diffraction pattern showed that NpAl is simple cubic with a = 4.262 % 0.005A, and is isostructural with UA13 where a = 4.27A1 or a =

Jan 1, 1954

By R. A. Cunningham, A. S. Murray

If a dense fluid such as mud or water is used for circulation, the formation drilled is influenced by a hydrostatic pressure. This pressure depends on hole depth arid drilling fluid density. Laboratory tests indicute that drilling rates in many forri~ations are decreased with increased pressure,—in some cases as much as 90 per cent. A comparison between laboratory and field tests indicates that drilling fluid head affects drilling rates in the field approximately the, same as in the laboratory. Drillirrg rates of many formations are increased by reducing drilling fluid head. INTRODUCTION For many years it has been noted that field and laboratory drilling rate tests did not agree even when the formations tested were the same. For instance, tests of some shales by the Hughes Tool Co. laboratory indicated drilling rates approximately 20 to 30 ft/hour, whereas in the ground this shale would drill only 3 to 5 ft/hour. A possible reason for this discrepancy is the effect of the high pressure which the drilling fluid exerts against the formation at the bottom of the hole. Consider a small element of rock (Fig. II that is to be removed by a rock bit. If the hole is filled with mud or water. the upper surface of the rock element is subjected to a pressure which depends on hole depth and fluid density. The mass of earth around this rock element presses against the circumferential surface and the lower surface. Because of the probability of shearing stresses between the rock element and the surrounding rock, this element is not under true hydrostatic stress. However, as a first approximation for test purposes the rock element was assumed to he under hydrostatic stress. The effect of hydrostatic pressure on some physical properties of rock has been studied.1,2,3 These tests show that the "differential" compres-sive stress:': necessary to cause rup- ture in rock cylinders is greater when tested under high hydrostatic pressure than when tested under atmospheric conditions. These tests were made with pressures greater than 20,000 psi which is in excess of those normally encountered in oil well drilling. Similar tests were made by the Bureau of Reclamation' using pressures equivalent to those encountered in oil well drilling. Again the "differential" compressive stress necessary to produce failure increased with increasing hydrostatic pressure. These tests indicated that drilling rates would probably decrease. Correlation between these tests and drilling tests was not practical. The purpose of this work is to study the effect of mud column pressure on drilling rate, assuming that the material drilled is in a state of hydrostatic strcss. This problem was initially investigated in the laboratory using variable bit loads and confining pressure;. Confirmation of laboratory results was obtained in the field from a series of carefully controlled drilling tests. Because of the necessity of testing many different types of formations. only results from representative formations will be presented here.

Jan 1, 1956

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By N. A. Rose, E. L. Spain

THIS study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. INTRODUCTION When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel- exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfulls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. SOURCES AND TYPES OF MATERIALS The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1937

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proa[n]o hill are the Fresnillo mines, and it is marked now by a great gash cut by gloryhole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo. which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notable active in 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1833 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de benefacio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

By Carl Floe

THE possibility of separating the various constituents of mixed ores or metalliferous products by differentially producing their soluble sulfates has not received the consideration that it deserves. The production of the soluble sulfate may be accomplished by baking the ore with sulfuric acid or by treating it with gases containing oxides of sulfur. This paper is primarily concerned with the first method. The procedure used was to mix the material with a solution containing a definite weight of sulfuric acid, baking the mixture at various tempera-tures and then leaching out the soluble sulfate with water. The amount of acid used was calculated to produce certain desired soluble sulfates. The temperature of baking depended on the decomposition points of the sulfates involved. The object was to prevent the formation of or to decompose certain sulfates while leaving a maximum quantity of another sulfate in a water-soluble form. This procedure has two possible advantages over the ordinary method of leaching with an aqueous solution of sulfuric acid. First, a more selective leach may be obtained, and second, the higher temperatures and stronger acid concentrations involved will permit a better recovery of materials that are difficultly soluble in relatively dilute aqueous sulfuric acid solutions. The method of sulfuric acid baking followed by water leaching is not new, as it has been applied in the treatment of various metalliferous materials such as the recovery of cadmium from flue dust1, the re-treat-ment of zinc leach residues2 and the working up of electrolytic slimes3.

Jan 1, 1936

By S. K. Basu, H. H. Kellogg

THE physical-chemical behavior of the system Pb-S-0 is of prime importance to the understanding of lead smelting processes, yet little accurate information is available on either equilibrium or kinetic behavior in this system. This paper is the first report of a program designed to fill gaps in our knowledge of this system. In the total ternary Pb-S-0, the region of greatest metallurgical interest is that bounded by the compositions Pb-PbS-PbS0,-PbO-Pb. Systems richer in sulfur, or richer in oxygen,* than those essentially pure SO2. This conclusion follows from the fact that all systems are in a highly reduced state, since either PbS or Pb is a constituent of all the equilibria. The content of 02, SO3, S2, S6, S8, and so forth, can be shown to be negligible compared to SO, in all such systems.* corresponding to this region can only be obtained at gas pressures exceeding 1 atm, a condition seldom met in lead smelting practice. Not only is the present study limited to condensed phases within this portion of the total system, but it is limited to temperatures at which all phases are pure solids, except for lead, which is liquid. In this limited system the following seven condensed phases are known to exist: Pb(l), PbS(c), PbO(c), PbSO,(c), PbSO,•PbO(c), PbSO4 • 2PbO(c), and PbSO, -4PbO(c). PbO exists in two crystal modifications,' but only the high-temperature yellow form is considered here. Schenck and co-workers2-4 reported the compound PbSO4 3Pb0 to be stable at high temperature, but the more recent work of Lander,5 and the present work, prove that the tetra-basic sulfate, rather than the tri-basic sulfate is stable. Fig. 1 shows the composition diagram for the binary PbO-PbSO2, based primarily on the work of Lander. In this study the univariant boundaries and invariant points existing among these seven condensed phases and the gas phase have been determined. In a ternary system, the phase rule indicates that an invariant point involves the simultaneous equilibrium of five phases—four condensed phases and the gas phase. A univariant relation involves four phases—three condensed phases and the gas phase. The gas phase in the systems studied is The following stable univariant equilibria between SOz and the condensed phases were identified: (a) PbS + 7PbS04 = 4(PbSO, - PbO) + 4SO2 (b) PbS + l0(PbS04 • PbO) = 7(PbSO4- 2PbO) + 4SO2 (c) PbS + 8(PbSO4 • 2PbO) = 5(PbSO4 . 4PbO) + 4SO2 (d) Pb + PbSO, • 4PbO = 6PbO + SO2 (e) 3PbS + PbSO4 . 4PbO = 8Pb + 4SO2 (f) 3PbS + 16(PbS04 PbO) = 7(PbSO4 . 4PbO)+ 12SO2 (g) 2PbS + PbSO,2PbO = 5Pb + 3SO2 (h) Pb + 3(PbSO4 . 2PbO) = 2(PbSO,. 4PbO) + SO, Of these eight univariant equilibria, five were measured in this work (a, b, c, d, and g) and the behavior of the other three (e, f, and h) was calculated by thermodynamic analysis of the measured data. Two invariant points were found corresponding to simultaneous equilibria as follows: Point 1: PbS, PbSO4PbO, PbSO4.2PbO, PbSO, - 4PbO, and SO2 Point 2: Pb, PbS, PbSO, . 2PbO, PbSO, - 4PbO, and SO2, From the measurements it was also possible to calculate the thermodynamic properties of the three basic sulfates of lead at 298.16°K. EXPERIMENTAL Apparatus—The experimental method consisted of the measurement of the gas pressure exerted by a given reaction mixture at a given temperature. An iridium crucible was used to contain the reaction mixture. There was no evidence of attack of the iridium,* but after use at high temperature for a week

Jan 1, 1961

By L. M. Pidgeon

The reactive metals are above manganese on the electromotive series. Their compounds are characterized by large heats of formation and they cannot be reduced from their ores by classical methods. Three general production methods have been used: a) Fused salt electrolysis, b) reduction of a halide by another metal, and c) reduction of the oxide by another metal. Method (a) is highly developed, as in the case of aluminum, (b) in the case of titanium, and (c) has been successful in the case of volatile metals such as magnesium and calcium. It is suggested that future improvements will take place in (a), and particularly in (c), but are rather less likely in the case of (b). THIS year of 1963 is the centennial of the birth of both Charles Hall and of Heroult, the founders of the aluminum industry. Aluminum is the one reactive metal which has reached massive stature in modern industry and perhaps the only such metal to have been produced in any quantity before the turn of the century. It has been joined by others, some on a very modest scale, but all of importance and all of fascinating interest. When invited to give the Fifth Extractive Metallurgy lecture, it seemed appropriate to look back upon the short history of this group to trace the developments which brought extraction methods to their present state and, at great risk, offer opinions as to future trends.

Jan 1, 1963

By E. Gilpin

The following notes may serve to bring before your Institute an idea of the iron-ore resources of Pictou County. Enough work has been done to permit an estimate to be formed of their quality and probable extent. As yet the systematic mining and smelting of ironore in Nora Scotia is confined to the operations of the Steel Company of Canada, in Colchester County. Although the locality I am about to describe appears, in many respects, well adapted to iron smelting, etc., no attempts have yet been made to begin work. Nora Scotian capital is more readily turned to lumbering, fishing, and shipping ventures; and such an investment appears equally foreign to the rest of the Dominion. I need not, however, go further into this part of the subject, and can only hope that my notes may prove serviceable as indicating a probable field for future development. The accompanying map shows the position of the harbor of Pictou relative to the coal and iron-ore fields, and to the railways which intersect them. The branch of the Intercolonial Railway, running from Truro to Pictou, forms the western boundary of the iron-ore district, which extends beyond the point where the New Glasgow and Cape Breton Railway crosses the French River. The iron-ore district may be roughly described as a triangle formed by the ore-outcrops and the two railways, the former making the base, and the latter the sides of the triangle, the apex resting on the coal-field at New Glasgow. The drainage of the country is toward the Gulf of St. Lawrence, through the Middle, East, Sutherland's, and French rivers; and the surface is undulatory, seldom exceeding two hundred feet above the sea-level, except in the district lying between Glengarry and the upper waters of the French and Sutherland's rivers, where a maximum height of about five hundred feet is reached at several points. Geologically speaking, the district embraces two divisions, the Carboniferous and the Silurian, the latter resting on strata provisionally considered to be of pre-Cambrian age. As no geological

Jan 1, 1886

By N. H. Harrison, J. K. Rodgers, S. Regier

This paper presents comparisons of data obtained from a laboratory reservoir study and from a calculated behavior prediction with the actual production history of a condensate reservoir. A small non-commercial discovery was depleted under closely controlled conditions and the well fluids were sampled at frequent intervals. Data on the reservoir and production variables were accumulated on a fixed schedule. A laboratory reservoir study war made using the initial well fluid samples as charging stock. The production procedures and operating conditions were held constant throughout the study wherever possible and in general paralleled the field work. The well fluid compositions and the cumulative recoveries ar a function of the reservoir pressure were also calculated using conventional flash vaporization procedures and equilibrium constants. Comparisons based on the composition of the well fluid show good agreement, the laboratory study agreeing within experimental accuracy with the field work and the calculated data comparing equally well. The gas-oil ratios are also in good agreement, but with somewhat greater deviations at the higher pressures. In the overall picture, it is believed that a model st,~tiy can predict within experimental accuracy the production history of a condensate reservoir. Better equilibrium constants for the heavier hydrocarbons are needed in order to attain improved composition accuracy by calculation. INTRODUCTION In Aug., 1955, a gas condensate well was completed in San Juan County, Utah, that was initially thought capable of good commercial production. These conclusions were derived principally from core data and electric logs, which indicated good permeability, porosity and gas content. However, after the usual series of potential tests it was found that the reservoir pressure had declined some 22 per cent, and it was obvious that the zone tapped was but a small pocket or trap. It became apparent that, with a controlled depletion of a small reservoir, a unique opportunity was available to compare laboratory and calculated studies with an actual field depletion and to further the present knowledge of condensate reservoirs. FIELD WORK The Coalbed Canyon Well No. 1 was conventionally completed in the Paradox limestone formation to a total depth of 5,912 ft. The producing zone from 5,762 to 5,806 ft was perforated with four jet shots per ft. The wellhead and field equipment were also conventional, the major items consisting of a two-pass indirect fired line heater, a high- and a low-pressure separator with the necessary controls and accessories, gas meters, back-pressure regulators, flare stacks and condensate stock tanks. The initial testing of this well con-sisted of a series of flow potential and pressure build-up tests during which some 30 MMcf of gas was produced. The reservoir pressure declined from an estimated 2,300 to 1,782 psig during this period, from which it was concluded that the reservoir was very small. In order to approach steady-state conditions in the reservoir and so provide optimum conditions for making comparisons, the field depletion was programmed to approach, if possible, constant production conditions. Bi-hourly readings were taken of the tubing pressure, the pressure and temperature of the separators, oil and gas rates, and other pertinent operating data. The gas rate, as indicated by the orifice meter, was held constant by the adjustment of the choke in the line heater. The temperature of the first stage separator was held constant by adjustment of the line heater jacket temperature. Practical considerations of production made the maintenance oi a constant gas rate impossible. The test started with a gas rate of 4 MMcf/D and a separator pressure of 250 psig. This rate was maintained until the choke was fully opened. The gas rate then declined with the falling tubing pressure and production was continued until the rate was about 2