Search Documents

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By Clarence Zener

[ ] THE present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 27 to 30. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1946

By R. D. Parker

LARGEST of any hoist installation ever manufactured in Canada is that being erected at No. 5 shaft, Creighton mine, of the Inter- national Nickel Company of Canada, Limited. It is a bicylindrical conical- drum hoist with the drums arranged in tandem, and driven by two direct- current motors through single reduction gearing. This hoist was designed by the Canadian Allis-Chalmers, Limited and manufactured at their works in Lachine, Quebec.

Jan 1, 1936

By AIME AIME

THE complete list of papers for the meeting of the Petroleum Division that is to be held" at Tulsa,' Thursday and Friday, Oct. 3 and 4,, with assignment to individual sessions is given below. THURSDAY MORNING First Session Well Spacing Theory of Well Spacing-By W. P. Haseman. Discussion by S. C. Herold, J. R. Suman and Lester C. Uren. Well Spacing in the Long Beach Field, California-By - Stender Sweeney. Discussion by C. H. McNeese; R. R Brandenthaler and W. V. Vietti. Well Spacing in the Bradford Field, Pennsylvania-By Paul D. Torrey. Discussion by A. F. Melcher, R. M.. Haskell, J. B. Umpleby and J. B. Newby. Results of Different Well Spacing in the Salt Creek Field, Wyoming-By Fred E. Wood. Discussion by Sam Grinsfelder and Kenneth B. Knowles.

Jan 1, 1929

At a large meeting of the members of the American Fund for French Wounded it which Mr. Franklin D. Roosevelt presided and at which Mrs. B. Girault Lathrop, President of the Paris Administration A. F.F. W., gave a most interesting address, special rows of seats were reserved for the members of the W. A. A. I. M. E. Those who were unable to be present will be glad to hear that Mrs. Lathrop complimented our organization on having supplied the largest dispensary operated by the A. F. F. W. and the Red Cross in northern France. The A. F. F. W. is going to erect an American Memorial Hospital at Rheims and it is hoped that the one hundred beds in the hospital will be endowed in memory of the men who gave their lives for the liberty of the world. It will be possible not only to endow beds, for which sums of $6000 each are needed, but also to give, as. memorials, sun- parlors at a cost of $10,000 each, two roof gardens at $5000 each, a laundry at $10,000 and a garage at $10,000. The New York Section has undertaken to endow a heel in memory of members of the A. I. M. E. who gave their lives in the Great War. Perhaps other Sections or groups of Sections may wish to do the same thing, or if no other Section cares to assume so much responsibility possibly individuals may like to join the fund already growing in New York, in which case they should send their contributions to Mrs. W. Y. Westervelt, 1 Lexington Ave., New York, N. Y.

Jan 6, 1919

[ ]

Jan 1, 1938

By J. F. Poland

Annual pumpage of ground water from the alluvial valleys of California now is about 10 million acre-feet. This heavy pumpage has created problems of over-draft and ocean-water encroachment in many valleys. Steps are being taken to protect and increase the available supply but much additional basic study is needed.

Jan 2, 1950

By A. A. Terchick, J. C. Anderson, D. T. King

During 1972-1973, U.S. Steel acquired an existing southern West Virginia high volatile coal mine property including a 150 tph heavy media feldspar jig preparation plant. Expansion of production from the property required an increase in plant capacity to 300 tph, replacement of the feldspar jig with a hydrocyclone circuit, and inclusion of a water clarification thickener system. The rugged and restrictive nature of the terrain adjacent to the plant facility indicated prohibitive construction costs and severe site congestion would be encountered if a conventional water clarification thickener were installed. A high-loading, small-volume thickener, developed initially for the sugar beet industry by the Enviro-Clear Co. of New York, was investigated by U.S. Steel Research for possible coal preparation application, utilizing bench scale and small scale pilot plant evaluation methods. Results of testing at existing U.S. Steel preparation plants indicated predictable successful application of the Enviro-Clear thickener, so a 35-ft-diam unit was installed. The two-phase thickener system, utilizing presettled bottom sludge as a filter-clarification media, has successfully performed since commissioning in April 1973, producing clarified water competitive with conventional thickener systems with freedom from usual thickener operational problems.

Jan 1, 1976

By C. M. Loeb, A. M. Gaudin, J. H. Brown

R. E. Carter (General Research Laboratory, Schenec-tady, N. Y.)—Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crys-tallographic directions, and in materials containing quartz because of the a-p' transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 1, 1960

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

[ ] S. H. Ash (Mining Industry Continues with Lower Fatal-Injury Rates, P. 257) was born in Roslyn, Wash. and attended Lehigh University and University of Washington. He received a B.S. and E.M. degree in mining engineering. Mr. Ash was supervising engineer in charge of work of Safety Div., Bureau of Mines, eastern Pennsylvania and the states of N. Y., Del., N. J. and the New England states. He was appointed chief engineer of Metal and Nonmetal Mining Section of the Mineral Production Security Div., Bureau of Mines, July 1942. At present he is chief engineer, Safety Branch, U. S. Bureau of Mines. Besides holding membership in AIME, he is a member of National Honorary Engineering Society, Society of American Military Engineers, Tau Beta Pi and many other societies.

Jan 1, 1952

By Manning W. Cox

Van Stone mine area is situated at the head of Onion Creek on the northwest flank of Gillette Mountain, Stevens County, Washington. The di strict was found during World War I, but the mine did not come into production until 1952. Production to the end of 1965 was 2,242,960 tons of ore that yielded 10,700 tons of lead concentrates and 120,000 tons of zinc concentrates. The area is part of the Selkirk Mountains Zinc-Lead Belt, or Kootenay Arc, extending from near Revelstoke, British Columbia, to Colville, Washington. A thick but incomplete section of Paleozoic marine formations occurs in the Kootenay Arc and is overlain by marine and continental Mesozoic formations. Both are invaded by Late Mesozoic-Tertiary batholiths. The belt is characterized by open complex folding and extensive high-angle and local thrust faulting. Principal ore deposits occur in the highly deformed carbonate rocks of Cambrian age-the Maitlen (Laib) and Metaline formations. The Van Stone mine occurs along a steeply S-shaped fold lying between the Kaniksu Batholith on the west and the Rogers Mountain Fault, a northeast-trending fault on the west flank of the Gillette Mountain Anticline, to the southeast. The fold is cut by northeasttrending faults containing notoriously irregular lamprophyric, diabasic, and pebble dikes. The host rocks, lower Paleozoic dolomites, are decolorized, silicified, and silicated in the mine area. Jasperoid and tremolite are the common alteration minerals. Other gangue minerals are barite, pyrite, brucite, calcite, and, near the batholith, pyrrhotite. Ore minerals are galena, jamesonite, and sphalerite. Ore minerals occur in bunches and pods intergrown with tremolite and jasperoid. Zinc is roughly eight times more abundant than lead. The highest ore outcrops at 3870 feet elevation, and an undeterminable portion has been removed by glacial scour. The lowest drill hole penetration has reached 3220 feet elevation. Oxidation ranges up to several hundred feet in depth and may be most closely related to pre-glacial groundwater circulation. The area of the mine was completely over-ridden by Pleistocene continental glaciers, and the present erosion surface is nearly continuously blanketed by up to 150 feet of glacial outwash.

Jan 1, 1968

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By N. P. Goss

Asterism appearing in X-ray Laue diagrams is an extremely sensitive index of changes in the internal structures of individual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.l-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not conclusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made between mosaic and distorted grain structures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example: has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-l4 to 10-l5 c.c., or 10-15 cm. in size. These crystallites, or blocks, appear to survive the most drastic cold-working, for it has been shown, and more elaborately by Wood's recent work," that cold-working cannot reduce the size of these crystallites smaller than of the order 10-5 cm. The interesting correlation brought out by the experiments of Goetz and Wood is that the block size after severe cold-working is of the same order of magnitude as the groups that formed in the metal just before crystallizing from the molten state. The work of Ewald and Rennenger17 and the now classical experiments of Darwin and James12,13 all strongly suggest the existence of a periodic structure of crystal. lites smaller than the grain itself. Related to this effect is the appearance of veinlike markings in the microstructures. Ammer-man and Kornfeld,16 in their experiments, did not observe any evidence of veining in specimens of alpha iron annealed below A3 and believed that veining was not due to impurities in the iron, as Northcott16 suggested; veining was observed by them only in specimens annealed above A3. Hanemann,16 Schrader and Tangerding found that annealing in hydrogen did not diminish veining and so it could not be caused by oxides. They concluded that veining was due to a slight difference in the orientation of ferrite lattice blocks. This viewpoint is well supported by the evidence presented here.

Jan 1, 1941

By Eugene Guccione

Australia could eventually become a major world supplier of uranium oxide-but how quickly that happens depends on the outcome of a highly complex and emotional battle among different special interests.

Jan 1, 1977

By A. C. Fieldner

The usual analytical determinations made in analyzing coal are comprised in the proximate and ultimate analysis and the determination of calorific value. The proximate analysis includes determinations of moisture, volatile matter, fixed carbon and ash; the ultimate analysis determinations of carbon, hydrogen, oxygen, nitrogen, sulfur and ash. The proximate analysis is an empirical process, and the results, obtained, especially for volatile matter and fixed carbon, are materially influenced by the method of conducting the determinations. This fact must be kept in mind in comparing coal analyses from different laboratories for classification purposes. Unless these laboratories have followed the same standard methods, differences due to variations in the analytical methods may, in some cases, be large enough to change the classification of the coal. It is unfortunate that the determinations of volatile matter and fixed carbon, which are most used in coal classification, are the two that are subject to the greatest variations. Moisture comes next in the scale of variation. The ultimate analysis is less influenced by method, since it comprises the determination of definite chemical elements. However, even the ultimate analysis is subject to errors, due to inorganic carbon from carbonates and to inorganic hydrogen from water. For these reasons it is evident that the Committee on Coal Classification must be informed on the evolution of methods of coal analysis in America and the average differences in analytical results that may be expected from variations in methods. The committee should be informed also on which methods should be accepted as standard for classifying coal and on the magnitude of the differences in results that may be expected from duplicate samples of the same coal sent to different laboratories for analysis by the same standard methods. It is the purpose of the present paper to provide this information. The subject will be discussed under the following main heads:

Jan 1, 1930

By G. N. Goldberg, Robert A. Rapp

The steady-state kinetics and microstructures of simultaneous internal oxidation and external scale formation were investigated for the oxidation of Cb-Zr and Ch-Zr-Re alloys in pure oxygen at 1000°C. For each binary alloy, a constant rate of scale formation was observed at steady state; the internal oxidatton zone reached a steady-state, time-independent thickness. The dependence of the scaling rate on zirconium content exhibited a maximum at a low zirconium colttent; more concentrated alloys oxidized at a slower rate than pure columbium. This composition dependence of the scaling rate may be partially attributed to the effect of the internal oxidation process as an intenla1 sink for oxygen, with the formation of voluminous, and relatively impermeable ZrO2 precipitates. However, the morphologies of the ZrO2 internal oxide precipitates also affected the scaling rate. The internal oxide precipitates were distributed uniformly in the external scale. The steady-state thicknesses of the internal oxidation zones were not in agreement with those predicted theoretically from an idealized simple model. However, in this particular alloy systen1 the ideal model is not satisfied experitmentally. For ternary Cb- Zr - Re alloys with Nr10e = 0.02 or 0.05, the steady-state thicknesses of the internal oxidation zones were less than those for the corresponding binary Cb-Zr alloys. For ternary alloys with NRe(0) - 0.05, a more adherent and much less porous external scale was formed, and a reduction in the kinetics of scale formation was observed. A number of authors'-7 have reported linear oxidation kinetics for the reaction of pure columbium at 1000°C in air or in oxygen of about 1 atm pressure. A thin and tightly adherent oxide layer is found at the metal/oxide interface beneath a porous external layer of scale. Although the suboxides CbO and CbO2 represent thermodynamically stable phases at 100O°C, generally only Cb2O5* is identified as a reaction product in quenched specimens. Studies at 1000°C at lower oxygen pressures8,10 (Po2 - 10-4 Torr) show that both CbO and CbO2 do form and that CbO2 is a protective oxide. The growth of CbO2 results in parabolic kinetics until Cb2O5 is nucleated and grows. Apparently because of the large volume change associated with its formation, Cb2O5 is porous and does not serve as a diffusion barrier; linear kinetics prevail after the surface is covered with Cb2o5. On the basis of these observations, several authors5,9,10 have suggested that the linear oxidation of pure columbium at 1000°C in air or oxygen of 1 atm is limited by a Loriers-type mechanism,11 whereby the total rate or reaction is controlled by ionic diffusion through a thin layer of CbO2 which is maintained at a constant thickness throughout the linear oxidation. However, the concept of a Loriers model for a three-phase CbOlCbO2 Cb2O5 scale, with the only oxygen activity gradient across the NbO2 phase, is not self-consistent. Further, the suboxides CbO and CbO2 were not observed in the high-temperature X-ray diffraction study of columbium oxidation by Goldschmidt.8 From investigations in which the large PO2, dependence of the linear scaling rate was demonstrated, the importance of an oxygen adsorption or dissolution step has been suggested.4,5,7,10,12 Thus the mechanism for the linear oxidation of pure columbium remains quite controversial. Since further insight into the oxidation mechanism of pure columbium is not provided by this investigation, the authors wish to emphasize at the outset that their experimental results are not interpreted in terms of a particular rate controlling step for the oxidation of pure columbium. Previous investigations13-18 of the oxidation of Cb-Zr solid-solution alloys in air or oxygen at 1000°C suggest a remarkable dependence upon zirconium content. For an alloy of bulk zirconium mole fraction, N2r(0) equal to 0.05 or 0.10, the oxygen uptake is reported to be as high as four times greater than that for pure columbium;13,14 for alloys with NZr(0) 0.05 or 0.10 the oxygen uptake is reported to decrease with increasing NZr(0); to a minimum uptake of about one quarter that for pure columbium at NZr(0): = 0.50.13-15Since zirconium forms a more stable oxide (ZrO2) than the lowest columbium oxide (CbO), and since columbium exhibits a high solubility19,20 and diffusivity21,23 for oxygen, the internal oxidation of the zirconium component to ZrO2 is expected at a reaction front ahead of the advancing metal/scale interface. The external scale is then formed at the metal/scale interface by the inward migration of oxygen through the scale, probably through a series combination of molecular and ionic diffusion. Internal oxidation in conjunction with external scale formation has been investigated by Maak24 for the oxidation of dilute Cu-Be alloys in pure oxygen at 850°C. For cu-Be and many other binary alloys,24-27 very small, essentially uniaxial internal oxide particles are formed in the most dilute compositions; for somewhat more concentrated alloys. the internal oxide particles precipitate as platelets or needles. From pertinent solutions to the diffusion equation, Maak28

Jan 1, 1967

By G. H., Wigton

THE present milling operations of the Chief Consolidated Mining Co. consist- of flotation of oxidized minerals from siliceous ores of the Tintic Mining district, Utah. As the lead, silver, and gold minerals that give the ores economic value are almost entirely oxidized; their successful flotation has necessitated the solution of many new problems. Laboratory effort resulted in the selection of a, natural float for the oxidized minerals. 'By "natural float," I mean that no reagent was added to produce a sulfide film on the osidized minerals before or while subjecting them to flotation operations. As compared to methods involving sulfide filming, the natural float was selected because it promised successful treatment of a larger variety, of ores without change in quantity or kind of reagents, as well as a better economic balance between metal recovery and concentration ratio. In explanation, I can, state that with sulfide filming, the efficiency of the method decreases rapidly with increase of hydrated, iron osides in the ore, whereas with the natural float the same effect has not been noted. Evidence shows that although sulfidizing can produce greater metal recoveries, it yields a concentrate so much lower in grade that no advantage results.

Jan 1, 1928

By J. M. Dumore

If in a vertical, downward miscible displacement, the transition zone between the displacing and displaced fluids is neglected, a criterion for stable displacement can be obtained by considering a small hypothetical protrusion of one of the fluids into the other. This criterion leads to the definition of the well-known critical rate, uc = kg p/p. The consideration is further extended by taking into account the transition zone that develops as a result of diffusion and mixing. A generalization of the previous criterion leads to the definition of another characteristic rate, the stable rate, which in actual miscible drives will be less than the critical rate. In such drives, the entire transition zone is stable at rates less than the stable rate. At rates between the stable and critical rates, the displacement is only partly stable, i.e. part of the transition zone adjacent to the displaced fluid is in an unstable position. From that part of the transition zone viscous lingers will develop. At rates greater than the critical rate the entire displacement is unstable and viscous lingers will develop more strongly. Results of laboratory experiments are in agreement with the expected behavior based on the theoretically deduced stability of the displacement. INTRODUCTION The simplest form of miscible drive in an oil-bearing formation is the injection of a fluid that is completely miscible* with the oil under reservoir conditions. In general, such a fluid, a solvent for example, is less dense and less viscous than the oil present in the formation. If it is injected into a horizontal homogeneous layer, gravitational forces will lead to the formation of a gravity tongue of solvent in the upper part of the layer and the adverse solvent-oil viscosity ratio will cause viscous fingers to develop. If, however, the solvent is injected up-structure into ,a dipping layer, gravity has a favorable effect, because it tends to keep the less dense solvent up-structure. Tongue formation and viscous fingering are consequently reduced and it is even possible that they will be suppressed completely. Viscous fingering and gravity tonguing are the consequences of the instability of the displacement. A stable displacement cannot result in growing viscous fingers and/or growing gravity tongues. Since large amounts of oil can be bypassed if there is viscous fingering and/or gravity tonguing, the stability of a miscible drive is very important with respect to the recovery efficiency of the drive. The stability is of particular importance in miscible-slug drives, as it determines how quickly the miscible slug between the displaced and displacing fluids will be distorted and broken up, after which the drive is no longer completely miscible. Stability is thus a most important factor in determining the success of a miscible drive, and it is considered that the aspects of stability considered in this paper will make a useful contribution to existing theories. Consideration is given only to vertical downward displacements, in which no gravity tongues can develop and which are therefore simpler than downward displacements in sloping layers. THEORY CRITERION FOR STABLE DISPLACEMENT Let us consider a vertical column of a homogeneous permeable medium saturated with oil. A solvent less dense and less viscous than the oil is injected at the top of the column at a constant rate; in the column the velocities of oil and solvent are assumed to be uniform. Diffusion and mixing of oil and solvent will at first be neglected, i.e. we assume that solvent and oil are divided by a sharp interface. An additional assumption is that the interface is horizontal. Continuity of pressures exists at the interface, because no capillary forces are present between the two miscible fluids. Consequently, at the interface (Z = I)):** Ps = Po - P-where Ps is the pressure at the solvent side and

Jan 1, 1965