Search Documents

By W. L. Phillips

Stress-train curves were obtained for single crystals of silver, Ag-5 pct Zn, Ag-10 pct Zn, and Ag-20 pct Zn tested in tension and shear at 78°, 195°, and 297°K. At room temperature the critical resolced shear stress gC increased, the length of' the easy-glide region increased, and the rate of' work hardening dwving easy glide decreased with increasixg zinc concentration. The change in the ratio of uc at room temperature to that at lower temperatures was significantly greater for the alloys than for pure silver. It was found that an increment in stress was necessary to continue slip when the slip direction was rotated 60 deg. The magnitude of this increment increased with strain for all alloys, increased with zinc concentration for a given strain, and for a given strain increased with decreasing -temperature. DESPITE its practical importance in improving the mechanical properties, alloying is not fully understood. Except for copper alloys few sets of systematic data are available. Von Goler and Sachs' studied the deformation of Cu-Zn alloys of increasing zinc content and found that, for dilute alloys, the critical resolved shear stress increases linearly with concentration. The range of easy glide was found to increase with increasing zinc content. Schmid and seliger,2 Sachs and Weerts,3 and Osswald4 have shown that with Mg-A1, Au-Ag, and Cu-Ni crystals, respectively, the critical resolved shear stress also varies linearly with concentration. More recently, Linde and his coworkers have investigated the variation of the critical shear stress of copper alloyed with tin , antimony, indium, germanium, silicon, nickel, and gold. They found that the slope of the critical resolved shear stress is related to the change of lattice parameter with composition, and also to the difference in Goldschmidt's atomic diameter between solvent and solute atoms. Garstone, Honey-combe, and creetham6 have shown that similar relationships can be found for small additions of silver, gold, and germanium to pure copper. They found that, with increasing silver or gold concentration, the critical shear stress for glide is increased by alloying, and so is the range of easy glide, which reaches as much as 60 pct for 0.50 pct Ag alloy and 0.62 pct Au alloy, as compared to 6 pct for pure copper of similar initial orientation. They also found that the alloying additions had little effect on the rate of hardening during easy glide, the slope scarcely changing with increasing alloy content. General secondary slip was detected only when the crystals began to harden rapidly. Although the slip appeared to be very fine in the early stages of deformation, coarser slip bands were formed towards the end of the extensive easy-glide range. The present investigation describes the deformation characteristics of single crystals of Ag-Zn containing different concentrations of zinc. Tension and shear testing were used for this study. EXPERIMENTAL PROCEDURE The method of growing the single crystals, sample preparation, and method of testing have been described in detail previously.' EXPERIMENTAL RESULTS A) Tension-Room Temperature. The initial orientations and stress-strain curves of single crystals of silver, Ag-10.0 pct Zn, and Ag-20.0 pct Zn are shown in Fig. 1. It is evident that there is considerable change in the stress-strain characteristics as a function of zinc concentration. The effects of zinc concentration on the critical resolved shear stress for both CU-zn8 and Ag-Zn alloys are summarized in Fig. 2. At all concentrations the resolved shear stress of the Cu-Zn alloys is higher than that of the Ag-Zn alloys. The resolved shear stress increases parabolically as a function of composition for both alloy systems. The length of easy-glide region increased with increasing zinc concentration, Fig. 3b). As the length increased the slope (do/de) decreased slightly, Fig. 3(b). Metallographic investigations demonstrated two significant effects of increasing zinc concentration. First, the amount of clustering increased, compare Figs. 4(a) and (b). The slip lines changed from uniform in pure silver to clustered in the Ag-20 pct Zn and Ag-30 pct Zn alloys. Second, the amount of cross slip decreased as the amount of clustering decreased.

Jan 1, 1968

By R. J. Wysor

J. S. UNGER, Pittsburgh, Pa.-On page 22 reference is made to 36 carloads .of dust shipped. Did the material in that last sample come from a; furnace running on pig iron, ferro alloys, or spiegel? R. J. Wysor.-Pig iron; we have not made any ferro alloys; or spiegel at Bethlehem in the last 3 years. J. S. UNGER.-DO you use domestic or foreign ores? R. J. WYSOR.-In regular practice, largely foreign ores. J. S. UNGER.-How much per unit does it cost to produce that? R. J. WYSOR.-You might say it does not cost anything; we do not change our blast-furnace practice at all to obtain the dust. Although it has been a profitable byproduct, I would rather not have it unless we could reclaim it on a large scale, as we would have better working stoves. J. S. UNGER.-Does the trade take it as readily as natural salts? W. J. WYSOR.-The fertilizer dealers have been anxious to get it. This did not happen, however, until the war started. J. S., UNGER.-They have been willing to take anything since the war started. R. J. WYSOR.-Yes. However, we could have sold the material before the war; in fact, about 4 years ago, we had a contract ready to sign, but we did not think it would pay us to bother with it then. W. H. Ross, Washington, D. C.-We of the Fertilizer Division of the Bureau of Soils have been particularly interested in Mr. Wysor's investigations on the possibilities of recovering potash from the blast furnace, and we look upon the results he obtained as among the-most important that have yet appeared on the subject of finding new sources of .American potash. About 5 years ago we undertook a corresponding investigation on the recovery of potash in the cement industry. Representative samples of raw mix and ground clinker were collected from the different cement plants in this country with a view to analyzing each sample for potash. With the data thus obtained and knowing the ratio between the raw mix and the cement produced and the output of the latter, we thought it possible to calculate approximately for each plant the quantity of potash that escapes daily from the kilns. After partly completing the work, however, it had to be abandoned for a time. It was again taken

Jan 4, 1917

By William F. Haddon, Phillip J. Maddex

Marco Polo brought the first borax to Europe late in the 13th century. It was especially treasured then for one of its many qualities-that of working with gold as a soldering flux. Georgius Agricola in 1556 gave it the name chrysocolla (which the Moors called borax)-literally, "gold glue." Deposits of borax have been elusive and widely scattered-first found only in Tibet and Italy, and, in 1836, at Iquiqui, Chile. Dr. John Veatch made the first California discovery in 1856 while examining a mineral spring east of Red Bluff. This "Borax Lake" soon supplied 90% of U.S. demand, but flooding and other production problems caused the scene to shift from Borax Lake to Little Borax Lake and then to Nevada in 1871. Early transportation was by "Twenty-Mule Teams."

Jan 1, 1971

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921

By U. Oko

The cause and the effect of disposing of tailings water from sulfide ore milling operation were examined. Dissolved metallic ions as well as dissolved sulfur-oxygen compounds (polythionates) can prove injurious to life in water streams. Polythionates originate in alkaline flotation circuits and may cause a severe drop in the pH of stream waters. It is proposed that a suitable "aging" period be allotted to tailings water to ensure complete conversion of polythionates to sulfate prior to neutralization and clarification treatment. Discharging alkaline solid-free tailings water without aging will cause downstream acidification. Artificial oxidation of tailings water can be economical only if the concentration of thiosulfate in solution is low. When the concentration is high, it is possible to reduce the concentration greatly by first acidifying the solution, because at a pH below 4 thiosulfate in water reacts to produce a precipitate of elemental sulfur and higher order polythionates. The residual polythionates can then be oxidized at great savings by natural aging or by chemicals such as ozone, chlorine, or peroxide. Chlorine may be an economical reagent for converting polythionates to sulfuric acid but the residual organo-chlorinated compounds can prove to be toxic to aquatic life. Ozone and hydrogen peroxide which do not leave a residue are preferred oxidizers.

Jan 1, 1976

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Nov. 10, 1917, to Dec. 10, 1917. ADAMS, LLOYD D Supt., Hoskins Mine, Mineral Point Zinc Co., Galena, Ill. ARMSTRONG, WILLIAM D., Min. Engr.. Empire Coal Co., 715 American Trust Bldg., Birmingham, Ala. BALL, TOM LEE, Efficiency Engr., Iron Mines Dept., Tennessee Coal, Iron &.R. R. Co., Bessemer, Ala. BENZIE, WILLIAM ROSE, Sec. & Treas., The Republic Coal Co., 901-2 Foster Bldg.,Denver, Colo. BERGSTROM, GUNNAR, Min. Engr.... Resident Mgr., Russian Dept., Swedish Diamond Rock Drilling Co., Slatawostowskaja Ulitza 6, Ekaterinburg, Russia. CADOT, J., Engr.,. Hardinge Conical Mill Co., Newhouse Bldg., Salt Lake City, Utah. COFFEY, GEORGE W 64 Santa Clara Ave., Oakland, Cal. CUTLER, WILLARD WALKER, JR Geol., Carter Oil Co., Tulsa, Okla.' . DANIEL, JOSEPH A., Min. Engr. & Geol., Hudson's Bay Co., Care The Institution of Mining & Metallurgy, 1 Finsbury Circus, London, E. C., England. EARDLEY, WALTER HAZEN, Cons. Engr., Chanute Spelter Co., 316 Frisco Bldg Joplin, Mo.

Jan 1, 1918

By L. C. Aycock, J. Hunter, P. M. Lyons

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By J. Hunter, P. M. Lyons, L. C. Aycock

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By Loyd R. Kern

A procedure for determining the behavior of a reservoir under a gas or water injection program was reported by Buckley and Levertt in 1942.1 This method, which allowed the calculation of the phase saturation distribution behind the front of a displacing fluid, has been extended to apply to a more general situation. The reservoir may initially contain flowing quantities of the displacing fluid, or the fluid in the reservoir may be above saturation pressure SO that solution effects are present. Production may occur behind the front as in the case of a well which is produced after breakthrough of the displacing fluid. The calculating procedure is simplified in that the graphical integration necessary to determine breakthrough saturation is eliminated by performing a direct integration and the graphical differentiation necessary to determine saturation distribution is eliminated by representing the displacing phase fraction of the flowing stream by an empirical equation. This representation results in simple expressions for the producing gas or water/oil ratio and cumulative production. INTRODUCTION A method for the calculation of the saturation distribution behind the front (interface between the displaced and displacing phases in a gas injection or water flooding operation) was reported by Buckley and Leverett in 1942. The method leads to a curve for the saturation distribution which is double-valued; consequently, part of' the curve was interpreted to be physically meaningless. That part of the curve which has physical significance was determined by a graphical integra-tion (material balance). In this paper it is shown that the integration may be performed analytically with a resulting equation for the saturation of the displacing phase at the front. The case in which the displacing fluid is initially flowing and the case in which the reservoir is initially above the saturation pressure so that some injected gas goes into solution are included in the integration. The calculations are considerably simplified by representing the fraction of the flowing stream which is oil by an exponential function of saturation. The methods is extended to apply approximately to reservoirs in which wells located between the injection well and the front are produced. An illustrative example utilizing the methods presented is included. RESERVOIR BELOW SATURATION PRESSURE In the case of a water flooding operation or in the case of a gas injection operation in which no gas goes into solution in the displaced oil, the equation for saturation in a linear flow system as a function of time and position as given by Buckley and Leverett is where* q = total reservoir volume flow rate, rvb/day A = cross sectional area of system, sq ft / = porosity of formation x = distance from injection point, ft t = time, days Pj = saturation of the displacing phase /dx velocity of planes of constant saturation, ft/day *The nomenclature used here is not the same as that used by Buckley and Leverett A complete nomenclature is given in Appendix A.

Jan 1, 1952

By Horace Pops

Martensitic transformation has been studied during cooling and heating in ß-phase Cu-Zn alloys to which small additions have been made of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, and Sb. The start and finish of the martensitic reaction and the variation of transformation temperature with third-element content were determined by electrical-resistivity measurements from alloys which had either constant zinc contents or constant values of electron concentration. All of the third elements, except nickel, lowered the transformation temperature if the results were plotted along the lines of constant zinc contents in each ternary system. A significant difference in the rate of lowering of the transformation temperature per atomic percent of the third element was observed for elements which had the same nominal valence. No systematic variation of transformation temperature with the valence of the third element was observed. It is suggested that the observed increase in transformation temperature for nickel-bearing alloys is due to the transfer of electrons from the conduction band of the alloy to virtual bound states. However, electron concentration is not the most important factor controlling the instability of the 0 phase. The transformation temperatures of the ternary alloys can be predicted from the following approxilnate expression: Ms (°K) = +3280 - 80 Zn + 8 Ni - 30 Ag - 12 Au - 140 Cd -90 Ga- 145 In - 80 Ge -175 Sn - 120 Si - 150 Sb MOST binary ß -phase alloys based upon the noble metals copper, silver, and gold are unstable at low temperatures and transform spontaneously by a martensitic reaction. This transformation has been studied recently in the ordered bcc ß'-phase Cu-Zn binary al1oys1,2 where the transformation temperature is below the room temperature and decreases with an increase in zinc content. It has been reported that the transformation temperatures can be raised above room temperature by small additions of a third element such as silicon3,5 or gallium,4,5 but no quantitative study has been made. The transformation temperature of different binary alloys can be altered by third-element additions. For example, it was shown that nickel and copper may have a large effect on the Ms temperature of CU-Al6 and Au-cd7 alloys. The present investigation was made to determine systematically the influence of various third elements on the martensite-transformation temperature of Cu-Zn ß-phase alloys. Since these alloys have an electronic origin,' alloy compositions were chosen so that the transformation temperatures could be determined at constant zinc contents or at constant values of electron concentration. I) EXPERIMENTAL PROCEDURE Ten ternary alloy systems were obtained by adding nickel, the noble metals silver and gold, and some B-subgroup elements to a Cu-Zn matrix. These are arranged according to their rows and columns in the Period Table as follows: Each ternary alloy was prepared by melting and casting weighed quantities of high-purity metals (99.99+ pct) in sealed quartz tubes under a partial pressure of helium to make a 4-g ingot. The molten alloys were shaken vigorously and then quenched in water. Since the weight loss was negligible, the compositions of the ingots after casting and annealing were assumed to be the same as the nominal compositions. The ingots were homogenized after casting in helium-filled Vycor tubes for 24 hr at temperatures between 750" and 810 C and quenched into brine. Metallographic examination revealed that all alloys were homogeneous, poly crystalline ß-phase alloys, and that the grain size was in the range 1 to 5 mm. Electrical-resistivity measurements were made to determine transformation temperatures of the ternary alloys during continuous cooling or heating. Transformation temperatures of the ternary alloys can be determined by electrical-resistivity measurements since the resistance of the martensitic phase is much higher than that of the 0' phase. The technique has been described previously in connection with a study of Au-Zn alloys.9 The reproducibility of transformation temperature was approximately ±6°C. II)RESULTS A hysteresis was always observed in electrical-resistivity curves and was usually less than about 12°C.

Jan 1, 1967

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By Gordon S. Duncan

(New York Meeting, February, 1912 THE U. S. Geological Survey, I believe, has almost completed a study of the Harney Peak quadrangle, preliminary to the publication of a report on that, district. As I was engaged for some months on an investigation of the mode of occurrence of the ore-bearing formation in this area, it has seemed to me timely to make public the results of my study, as a contribution to the consideration of this subject. It seems scarcely necessary to describe the locality and general geology of the Black hills of South Dakota, for since 1846 many have contributed information concerning this region, some of the reports bearing such well-known names as those of Walter P. Jenney, Henry Newton, S. F. Emmons, and C. R. Van Hise, while we have only to glance at Bulletin No. 4 of the South Dakota School of Mines, in which Prof. C. C. O'Harra, of that institution, has given us a bibliography of contributions to the geography and geology of the section, to find that other well-known men have studied the district, and have given us the benefit of their researches. The U. S. Geological Survey has made geological maps of nearly the whole of the Black hills, the only quadrangle yet to be completed being, as stated, the Harney Peak district. During the late summer and autnmn of 1910, it was my lot to examine and report. on a considerable area in this neighborhood, which once had been prospected, and in some cases exploited, for tin. This paper gives an account of certain geological phenomena, noted at that time, which greatly influenced my conclnsions. The predominating formation of the district is pre-Cambrian, represented by a highly-cleaved mica-schist, usually very garnetiferous, and sometimes hornblendic. Rising like an island from the surrounding schist is a large mass of granite, known as

Jul 1, 1912

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By H. Kobbè William

ARTHUR KNAPP, Ardmore, Pa. (communication to the Secretary*).¬On p. 2275 I find a quotation from Mr. Thompson regarding the fountains of the Baku field. I have seen a large number of these gushers or fountains. In every case where unusual amounts of sand were produced the wells caved in and shut off in a few clays and were an absolute loss Very often the formation had caved so far up as to allow the water to enter the oil strata, and not only was the well lost but the ground for many acres around the well was useless for drilling purposes because the disturbed ground had allowed the gas and oil to dissipate and the water to enter. On p. 2268, Mr. Thompson is again quoted regarding the Balakhany field. If the text is consulted further, it will be found that the oil at Balakhany is heavy only in contradistinction to the Bibi Eibat, field. The gravity of the oil at Balakhany is from 28 to 32. Also, it must be noted that the illustration is taken from the conditions in the older part of the field. This field was first chilled 40 years ago, and was a worn-out field 15 years ago. The wells which produce sand are wells in which the casings are practically gone and the formations are full of water. The sand must be bailed from these wells because the clays from the upper stratum have caved into the wells and are obstructing the passage of oil. On p. 2262 is the statement that the Russian wells cannot be pumped on account of the large amounts of free sand produced. They have never tried pumping in the Baku field to any extent. Wherever tried, it has proven a great success. If we take the author's theories as correct and wish to put them into practice, it would first be necessary to consider a few figures. Let us assume that we produce oil and sand together in the proportion in which they exist in the productive strata. It is not uncommon to have wells in the California field which are not gushers, but which, by pumping, produce 1,000 bbl. per clay the first 100 clays.

Jan 3, 1917

By G. Derge, L. D. Kirkbride

In recent years the problem of sulfur elimination in iron and steel-making has been of increasing importance. This interest has been due to the increasing amounts of sulfur coming into the system via raw materials. As a result, many investigations have been directed at obtaining information pertaining to the rate and mechanism of sulfur removal in the blast furnace as well as measuring appropriate thermodynamic quantities. Chang and Goldmanl as well as others2'3 showed that the process of sulfur transfer from molten carbon-saturated iron to blast furnace-type slags could be considered as two opposing first-order chemical reactions. Recently, Ramachandran et al.4 have shown that during desulfurization electrical neutrality is preserved in both phases and iron and silicon are transferred into the slag concurrently with the evolution of carbon monoxide gas. They concluded that the reaction s + c-+ (0)=(S) + CO(g) does not express the stoichiometry of the sulfur transfer process. As in all previous investigations, these authors studied the process of a net transfer of sulfur from metal to slag across a slag-metal interface. However, no experimental data have previously been obtained for the process of sulfurization. It was the purpose of this study to investigate the sulfurization process, i.e., net transfer of sulfur from slag to metal. EXPERIMENTAL PROCEDURE Apparatus—The equipment used in this investiga-tion was typical of that used by others.1-3The furnace was a high-frequency induction unit powered by a 35 kw Hg spark gap converter. Fig. 1 shows a schematic diagram of the apparatus. A two-compartment crucible assembly was employed to melt the slag and metal charges; being similar to that used by Ramachandran,4 in size and design. The atmosphere was that produced by reaction of hot graphite with air. Temperature measurements were made by W-Mo thermocouples which were calibrated against a Bureau of Standards Pt - Pt 10 pct Rh couple. Temperature control was always good to * 5°C and in general was much better than this figure. Raw materials used in the experiments were C. P. reagent grade where possible. The silica used in the preparation of the slags was in the form of highly purified silica flour. Silicon and titanium additions

Jan 1, 1961

By M. S. Abrahams

Germanium has been rolled in the temperature range of 700o to 800°C. The thickness has been decreased by as much as a factor of four, from a thickness of 0.032 in. to a thickness of 0.008 in. For deformations below 60 pet, the true strain per pass is found to be a constant; from the temperature dependence of this slope, an activation energy of about 2.5 ev is obtained. This energy agrees with that for dislocation climb in germanium . For reductions greater than 60 pet, complete rings are seen in the Lave photographs, new grains are observed in the microstructure, considerable softening occurs, and the hole mobility is very low. This evidence indicates that the recrystallization of gertnanium has occurred. GERMANIUM has been deformed in many ways1 including tension, compression, torsion, and bending since Gallagher2 first described its plastic nature at elevated temperatures. All of these studies indicate that the glide plane in germanium is (111) and that the glide direction is (110). Rolled germanium specimens were used by Kolm, Warekois, and Kulin3 in their X-ray study of deformed semiconductors, but no information is given on the rolling itself. The present experiments deal with the rolling of germanium at various temperatures and for different orientations. In all previous deformation studies, the phenomenon of recrystallization (i.e., the transformation of a single crystal into a polycrystal) in germanium has not been observed4 despite relatively large deformations at elevated temperatures. The proposed reason4 for this was that sufficient energy could not be stored in the deformed germanium lattice. In contrast to the earlier studies this work will present evidence indicating that recrystallization occurs in germanium during rolling at an elevated temperature. I) EXPERIMENTAL PROCEDURE A) Test Specimens. The samples used for rolling were in the form of rectangular parallelepipeds measuring 0.3 in. long, 0.06 in. wide, and 0.035 in. high. They were cut from an undoped single-crystal ingot of p-type germanium with a resistivity of 24.4 ohm-cm, a Hall mobility of 2300 sq cm v-' sec-l, and a hole concentration of 1.1 x 1014 cm"3 at room temperature. The surfaces of the specimens were metallographically polished prior to rolling. The initial dislocation density of the samples was about 10' cm-' as determined by etching in CP4. Two different specimen orientations were used. In the first case, the direction of rolling was parallel to (251), the surfaces in contact with the rolls were of the form (1021, and the normal to the third face was parallel to (211). The corresponding di-

Jan 1, 1964

By F. Z. Schellenberg

(Pittsburg Meeting, March, 1910.) SYSTEMATIC exploitation in the Pittsburg coal-seam on a large scale is simple where the boundaries of the property do not interfere by forcing drainage-, ventilation-, and transport-lines of entries to be run to particular confined fronts. A prime condition governing development is the natural direction of the seam's perpendicular cleavage-planes, giving long lines of smooth faces near together and parallel, bearing about 65° to the left of the meridian and therefore crossing the basins. The gradients of dip into the basins change from 10 per cent at the east rim to practical flatness northwestward across the great coal-fields, a hundred miles wide; the clip being halved in rate at each successive crossing-over of an anticlinal crest. Elevations above sea-level on this transverse section, in scope of present development, differ by 1,000 ft. between low trough and high outcrop. Local irregularities of dip are found, but the main feature to be recognized is the pitch of the basins-the general rise northeastward at 20 ft. per mile, from 100 ft, below sea-level at the low point near the. SW. corner of Pennsylvania to 1,500 ft. and more above tide, and the appearance then, at the surface, of the lower coal-seams carried in the next deeper-lying thousand feet of rock-measures; below which series come the oil- and gas-sands of Oliphant's charted column of strata, reaching down altogether 3,000 ft. below the Pittsburg coal-seam. Because of -the general regularity of occurrence of the coal-seam, the mine-map depicting the courses of economic operation to be undertaken and the steps in controlled exhaustion, need be but a projection of two dimensions on the horizontal plane of space, and this for the most part composed of natural, almost unbroken lines, on the face and on the end of the coal, co-ordinating rectangularly.

Jul 1, 1910

By T. Cuscino, D. D. Lane, C. Cowherd, T. E. Baxter

Three types of commercially-available dust suppressants, commonly used in the surface mining industry to control fugitive particulate emissions from unpaved roads, were tested in the laboratory for cohesive strength and resistance to reduced effectiveness by large water addi¬tions. Results indicate that each product tested varies in cohesive strength with a range of 34-300 kPa (5-44 psi). Total cohesive strength depends on the aggregate moisture content and the means by which the sample is dried. Results show that laboratory testing can be used as a decision¬making tool concerning the type of dust suppressant for a particular mining operation. Also, the road surface aggre¬gate moisture content u critical to successful dust suppres¬sant performance. Large water additions to the aggregate road surface after initial suppressant application can pro¬duce nondesirable results. A modified wet sieving analysis is presented to test the effect of water addition.

Jan 1, 1984

By Earl Oliver

CONTENTS PAGE A.I.M.E. Stabilization Committee Activity 3 Definition of Capture Rule: Robert E. Hardwicke 4 Westmoreland Natural Gas Co. vs. DeWitt 5 Kelly vs. Ohio Oil Co 5 Bernard vs. Monongahela Gas Co 6 Definition of Ownership in Place 7 Prospective Stabilization Remedies 7 Dean Roscoe Pound's Four Tests of Practicability 7 I: Mechanically Feasible 8 Capture Rule 8 Ownership in Place 10 Mechanical Separation Method 10 Engineering Appraisal Method. 11 II. Economically Advisable. ., . 13 Capture Rule 14 Ownership in Place 14 III. Politically Wise 14 Capture Rule 14 Ownership in Place 17 IV. Legally Sound 18 Capture Rule 18 Ownership in Place 19 Dean Henry M. Bates' Analysis 19 Resume 22 THE A.I.M.E. Stabilization Committee was named in 1932 to ascer-tain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from. E. DeGolyer under date of Jan. 25, 1935, in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937

By J. M. Dahl, L. H. Van Vlack

STAFF: Editor, Gerhard Derge Associate Editor, Paul G. Shewman Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Post-President; Harold B. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. B. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of monuscripts is under the supervision of the following Publications Committees: Extractive Metollurgy Division: R. E. Grace, Chairman; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Healy, T. A. Henrie, R. D. Holli-day, C. E. O'Neill, C. S. Sami s, A. W. Schlech-ten, and Charles Shull . Iron and Steel Division: R. D. Pehlke, Chairman; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Tuckdogon, L. H.Von Vlack, and J. M. Uys. Institute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Chairman; M. R. Achter, G. F. Bolling, J. O. Brittain, G. P. Conard, II, L. A. Girifolco. G. T. Hahn, J.P. Hirth, L. Himmel, G. T. Horne, George Krauss, C. F. Leitton, Jr., J. D. Livingston, R. D. Monning, H. M. Otte, S. V. Radcliffe, R. E. Reed-Hill, H. C. Rogers, O. Sherby, M. T. Simnod, G. R. Speich, E. A. Steigerwold, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Walton, H. W. Weart, W. W. Webb, and D. WiIsdorf. Published monthly by the American lnstitute of Mining, Metollurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York, N. Y. 10017. Telephone PLAZA 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1965 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustrial Arts Index, and Chemical Abstracts . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 233, Number 1.

Jan 1, 1965