Search Documents

By T. F. Witherbee

ON the 22d of November, „1879, white iron unexpectedly appeared while working the Cedar Point Furnace, Port Henry, N Y., on the following burden, calculated to turn out mill and foundry iron: Anthracite coal, - 3000 pounds. Connellsville coke, - 1500 pounds. Total, - 4500 pounds. Old Bed ore, - 3750 pounds. New Bed fine ore, - 2000 pounds. New Bed chunk ore, - 1000 pounds. Kearnev hematite ore, - 750 pounds. Total, - 7500 pounds. Magnesian limestone, - 1865 pounds. Common limestone, - 885 pounds. Total, - 2500 pounds. The production per week since making mill iron-from September 1st, 1879, to date, seven weeks-was 412 gross tons. Ore was not immediately taken off, as nothing serious was looked for. The iron for the next week graded from No. 4 to white, and in. six days the make was 274 1/2 tons. At 10 P.M., Friday, the 28th, a slip of-..4 feet occurred, and on Saturday, at 5 A.M., another of 3 feet on the south side and. 7- feet on the north side took place. At this time it was found that the south side had been hanging for over a week--a fact which had not been reported. Throwing off the wind, to produce slips. and reduce pressure, had been tried with no effect. The stock, as seen through the tuyeres, seemed to consist almost entirely of coal, with just enough infusible cinder to cement it into a mass through which the blast could not be forced. At 3.50 A.M., Sunday, the 30th, the first cinder seen in seventeen hours came into tuyeres Nos. 1, 2, 3, and 6, At 9.30 A.M. No. 3 was taken out to see if the stock

Jan 1, 1881

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By Ta M. Li

Expanded mine-mill capacity and greater operating flexibility are part of the dramatic changes taking place in the Tennessee mining operations of Asarco, Inc. Climaxed by the recent start-up of the $6.3 million Young mill in September 1975, Asarco has pushed Tennessee back into number one position as the leading zinc mining state. Furthermore, start-up of the Young mill is expected to insure a much-needed and continuing domestic zinc supply, at a time when US mines can only supply one-half of 1975 domestic consumption.

Jan 5, 1976

By Nicholas J. Grant, David S. Bloom

An investigation of the Cr-Ni system has revealed that there exists a eutectoid transformation at about 1180°C. 'The transformation in chromium implied by the eutectoid reaction was detected at about 100°C below its melting point. Associated with the eutectoid transformation, a metastable transition structure has been found. THE Cr-Ni phase diagram is shown in current literature to be a simple eutectic system in which the high chromium end of the diagram is incompletely determined, Fig. 1. The last investigation of this system was undertaken in 1936.' Because of limitations in metal purity, especially of chromium, and temperature measuring techniques, the diagram should be accepted with some reservations, as was indicated by Hansen.V or examwle.-, the wresence of the compound Cr²Ni, with a tetragonal structure," remains unverified and incompatible with the simple eutectic diagram. The work reported here began because of discrepancies that appeared in experimental studies in the binary alloys Cr-Ni and in the ternary system Cr-Mo-Ni. The existing binary Cr-Ni diagram failed to provide a complete explanation of observations made by microscope, X-ray, and thermal analyses. Experimental Methods The materials employed were of a higher degree of purity than were available to previous investigators. The Mond nickel used had a nominal purity of 99.87 pct, while the electrolytic chromium analyzed 99.03 pct with the major impurity being 0.5 to 0.7 pct oxygen with some iron. All alloys were melted in a vacuum furnace to remove dissolved gases, sufficient carbon was added to the charge to combine with all the oxygen as CO. Final analysis determined the carbon as about 0.02 pct and the oxygen around 0.06 pct or slightly more. Stabilized zirconia crucibles and thermocouple protection tips were used throughout and contributed no detectable impurity to the melts, as long as the oxygen in the chromium was kept low. Heats averaged about 250 g, which permitted about 2 in. of the thermocouple protection tips to be submerged. The temperature drop across the thermocouple protection tip was determined to be about 3°C, a minor source of error. The alloys, after removal from the vacuum furnace, were placed in a furnace operating in a purified argon atmosphere for the thermal analyses. An- nealed wolfram-molybdenum thermocouples provided the primary means of temperature determination, though a Pt-Pt-10 pct Rh couple was employed for a check when possible. A sensitive, high-speed Leeds and Northrup Speedomax recording potentiometer indicated the thermocouple output. X-ray diffraction patterns were obtained primarily on a Norelco unit, which permitted diffraction angles only up to 45" (28 = 90"). In general, either rotated or stationary solid samples were used, because it later evolved that many samples were susceptible to transformation resulting from the cold working involved in pulverizing. It was also noted that rotating a sample sometimes suppressed weak lines, so, usually, samples were not rotated. Later a high temperature camera was adapted for use at temperatures up to 1400 °C on the Norelco unit utilizing both solid and powdered samples. Unless otherwise noted, all X-ray patterns were made with a chromium tube and a vanadium filter. Further-

Jan 1, 1952

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

By W. S. Ayres

By N. H. van Lingen

A laboratory stud], has been made to determine what factors affect the penetration rate of roller bits, diamond bits and drag bits in rock drilling with clay /water muds. The rather simple relations that exist when pressures in and around the borehole are equal become more conzplicated when under down-hole conditions the penetration rate is hampered by the existence of a pressure differential between the mud at the hole bottom and the pore liquid at cutting depth. Expressions that have been derived for both the penetration rate and the magnitude of the pressure differential in permeable rock together fully account for operating, rock, mud and bit variables. In impermeable rock a similar pressure differential is caused by the bit action itself. In all cases, the pressure difierential and the reduction in penetration rate increase with the effectiveness of the plastering at the bottom of the hole by mud particles. Where bits are employed whose action is largely that of crushing, however, the plastering may become even more effective owing to the addition of rock particles rubbed into the pores of the rock. With roller bits, a plastically hehaving layer may be formed, which causes a further reduction in penetration. In the case of bits whose action is chiefly scraping, moreover, penetration may be arrested by the bit's becoming balled-up. The various adverse effects are reduced by thorough scavenging of the hole bottom. This paper shows how with jet bits the efficiency of such scavenging may he improved by suitable choice of the position of the nozzles. INTRODUCTION The reduction in a bit's penetration rate with increasing depth of hole has been the subject of many investigations. Various investigators ',' have independently reached the conclusion that this reduction occurs not so much because the rock-breaking process becomes more difficult as it does because the lifting of the rock fragments is impaired by a fluid pressure differential holding the fragments down. When such a pressure differential can be avoided, as in air drilling and to a smaller extent in water drilling, penetration rates remain high. Although the range of applicability of these techniques is being extended, most oil wells still have to be drilled with mud. In this paper we present the results of laboratory experiments carried out to determine what factors govern the hold down effect encountered in mud drilling. In the course of this investigation, the well known importance of bottom scavenging came more and more into prominence. Not only may it reduce the magnitude of the hold-down forces, but also it appeared to be a means of preventing the accumulation of a plastic mass of cuttings and mud on the hole bottom and bit which may cause penetration to cease almost completely. So that the effects of fluid pressures may be more readily understood, the factors that govern penetration rate in the absence of these pressures will first be discussed. The effect of down-hole pressures will then be assessed for the case of permeable rock where fluid pressures are well defined, and it will be demonstrated how rock strengthening due to confining can be accounted for. Subsequently, fluid pressures in less-permeable rock will be examined; we will show that in impermeable rock it is the bit action that governs fluid-pressure distribution and hold-down. In the case of poor scavenging and/or high bit load. cutting cake manifests itself. The effect, like various others. appears to depend on the type of bit used. From the very beginning, therefore, we shall base our discussion on the three main types of bits used in rotary oil-well drilling— roller bits, diamond bits and drag bits. Since space is limited, it will be impossible to make more than a passing reference to many aspects of the problem. Moreover. certain relations that are not of primary irnportance to our argument will unavoidably have to be stated in a somewhat dogmatic fashion, and the experimental data on which these are based necessarily must be omitted. EQUIPMENT The drilling experiments were performed on three machines, of which one has been designed for the realistic simulation of down-hole pressure conditions. HIGH-PRESSURES MACHINE In this machine (diagramed in Fig. 1) the mud, pore and confining pressures can all be adjusted independently. The foil-covered rock sample contained in the inner pressure vessel is confined by oil that is pressurized by means of a hand pump. The pore space of the watersaturated sample is connected to an arrangement which keeps the pressure in the pore space constant regardless of the rate of filtrate flow through the sample.

By Emil Gathmann

(San Francisco Meeting, September, 1915) THROUGH wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," -i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot: Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe .at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium,

Jan 8, 1915

By C. E. Lundin, D. T. Klodt

The binary alloy systems, Y-Ti, Y-Zr, and Y-Hf, have been investigated throughout their entire composition regions. There is no compound formation in any of the systems, and each system is characterized by a single eutectic reaction. The eutectic compositions and temperatures are as follows: A eutectoid reaction pct Y and 870°C occurs in the Y-Ti system, whereas a peritectoid reaction,: pct Y and 880°C occurs in the Y-Zr system. Peri-tectic-type reactions at temperatures above the eutectic levels are postulated for the yttrium and hafnium transfovmations. The development of the technology of yttrium has been given considerable attention during the past few years, and studies of binary phase equilibria have, of course, taken a prominent position in this development. In many respects yttrium, in the third group of metals of the periodic table, is similar to the adjacent group of metals, titanium, zirconium, and hafnium, and the knowledge of the phase relationships of yttrium with these metals is basic to their technology. MATERIALS AND EXPERIMENTAL PROCEDURES Materials. The metals for this investigation were supplied by the General Electric Co., Aircraft Nuclear Propulsion Department. The yttrium was in the form of an arc-melted ingot, and the other metals were in the form of high-purity, iodide-Process crystal bar. Table I lists the purities of these materials. Alloy Preparation. Melting was done by conventional techniques in a nonconsumable electrode arc furnace in an atmosphere of purified argon. Melting conditions for each binary system were the same. Each alloy button was inverted and remelted several times to assure homogeneity. Accurate weights of the charges and resultant alloy buttons were obtained to indicate deviations from intended compositions. No chemical analyses were obtained since melting weight losses were consistently in the range of 0.1 to 0.2 pct of the total weight. 10- or 20-g buttons for each 5.0 wt pct composition increment were melted to survey the three individual alloy systems. Additional alloys differing in composition by 1.0 or 0.1 wt pct increments were also melted to study selected regions of the systems. Metallograpllic Techniques. Standard metallo-graphic techniques were followed for mounting and rough grinding. Preliminary polishing was accomplished using 6-u diamond paste as an abrasive on a Metcloth Lap. Final polishing was done on a Microcloth-covered wheel using 1-u diamond abrasive paste. Purified kerosene was used as a lubricant for both polishing stages. • sothermal- Annealing. Alloys were sectioned for as-cast structlure examinations and then homogenized in preparation for isothermal-annealing treatments. Homo{:enization was accomplished by cold pressing the alloy buttons followed by 72-hr anneals at 1100c. The alloys were encapsulated in Vycor or quartz for the homogenization treatments or for isothermal anneals. Resistance-wound or resistance-element tube furnaces were used for the annealing treatments. The homogenized alloy buttons were cold rolled until cracking occurred or until a -in. specimen thickness was obtained. Small -in. square) specimens for the isothermal anneals were then sawed from the alloys. Each specimen was wrapped in tantalum foil before being sealed in the capsule. Temperatures during the anneals were controlled The time at temperature necessary to equilibrate the structures during the anneals was determined for each alloy system by holding triplicate specimens of alloys at a constant temperature for three different periotls. The specimens were quenched and examined microscopically to determine the number and amounts of phases present in the micro-structure as a function of time. Melting Studies. Eutectic temperatures of the three alloy systems were established from the results of incipient-melting studies conducted on as-cast alloys. Specimens to be melted were suspended on a tungsten wire inside a graphite cylinder placed in a glass vacuum chamber. An optical pyrometer was used to follow the temperature of the specimen as it was inductively heated in a high vacuum. The temperatures were corrected for emissivity losses by standardizing the pyrometer with known-melting-point metals. Accuracy of the temperature measurements is estimated to be + 10°C. The melting point of the yttrium was determined to be 1550°C by this technique. The invariant-temperature levels were also checked by an anneal-quench technique. This technique consists of annealing a series of

Jan 1, 1962

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200°C, a wide range of conveyors is available. Special constructions of rubber conveyor belts. steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400°F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F.

Jan 5, 1953

By Robert B. Sosman

THE relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. DEVELOPMENT OF METHOD The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreciation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. PYROMETRY OF COKE The coke inside a by-product oven is almost completely inaccessible to pyrometric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1942

By Theron Wasson

The discovery of two new fields—the Reed City area of Osceola County and the Headquarters field, of Roscommon County —and the important development in Winterfield township, Clare County, again demonstrate the fact that it is the unknown and unexpected that enter very definitely into the oil-producing history of Michigan. This is particularly true in the area of thick glacial drift in the north central part of the state, where the new prolific fields have been discovered this year. This shifts the interest from the southwestern part of the lower peninsula, where a number of pools were rapidly developed during 1939 and 1940, back into the Central Basin area. As a result of strict proration in the new areas, the production for the state of Michigan for the year has not been as great as in 1940 or 1939. In 1941 the total production was 16,300,000 bbl., in 1940 it was 19,551,000 bbl., and in 1939, which was the peak year, it was 23,300,000 bbl. However, the discovery of the new fields this year nearly doubles the estimated reserves for Michigan reported at the end of 1940 In 1941 about 12,000,000 bbl. of oil was produced from the older fields, in which the individual well productions were so small that proration was not an important factor. The total production for the state from the discovery of oil in 1925 through 1941 now stands at 161,205,000 barrels. ActIVe Oil Fields Reed City Field.—In the Reed City field, Lincoln township, Osceola County, only small oil wells were completed during 1939 and 1940. The discovery of much larger production in wells drilled somewhat deeper, by The Pure Oil Co. and the Weber Oil Co., in the early part of 1941, led to the rapid development in this area. Some wells have had initial productions as high as 10,000 bbl. By the end of the year III producing wells were completed, with an average depth of 3600 ft., from the Detroit River formation of Devonian age. The entire development of the field to the end of 1941 was on 20-acre spacing. Headquarters Field.—The Headquarters field, which lies along the line between Clare and Roscommon Counties, was one of the most important discoveries of 1941 and will be the scene of vigorous development during 1942. Production so far has been from the Traverse lime at about 3400 it., and development has indicated that this is probably one of the most productive Traverse pools yet discovered. One well had been given a potential of 10,000 bbl. per day. Dry holes well located in relation to big producers indicate that it is a typical Traverse development. Winterfield Field.-This field, in Winter-field township, Clare County, was discovered late in 1940. By December 1941, 14 Dundee and 5 Traverse producers had been completed. The Dundee lime is found at a depth of 3750 it. and the Traverse lime at 3070 it. Producing conditions in the Dundee seem to be erratic because of varying porosity in the dolomit-ized limestone. Kawkawlin Field.—The Kawkawlin field, which was discovered by the Gulf Refining Co. in 1938, is in Monitor and Kawkawlin townships, Bay County. Small production

Jan 1, 1942

By Theron Wasson

The discovery of two new fields—the Reed City area of Osceola County and the Headquarters field, of Roscommon County —and the important development in Winterfield township, Clare County, again demonstrate the fact that it is the unknown and unexpected that enter very definitely into the oil-producing history of Michigan. This is particularly true in the area of thick glacial drift in the north central part of the state, where the new prolific fields have been discovered this year. This shifts the interest from the southwestern part of the lower peninsula, where a number of pools were rapidly developed during 1939 and 1940, back into the Central Basin area. As a result of strict proration in the new areas, the production for the state of Michigan for the year has not been as great as in 1940 or 1939. In 1941 the total production was 16,300,000 bbl., in 1940 it was 19,551,000 bbl., and in 1939, which was the peak year, it was 23,300,000 bbl. However, the discovery of the new fields this year nearly doubles the estimated reserves for Michigan reported at the end of 1940 In 1941 about 12,000,000 bbl. of oil was produced from the older fields, in which the individual well productions were so small that proration was not an important factor. The total production for the state from the discovery of oil in 1925 through 1941 now stands at 161,205,000 barrels. ActIVe Oil Fields Reed City Field.—In the Reed City field, Lincoln township, Osceola County, only small oil wells were completed during 1939 and 1940. The discovery of much larger production in wells drilled somewhat deeper, by The Pure Oil Co. and the Weber Oil Co., in the early part of 1941, led to the rapid development in this area. Some wells have had initial productions as high as 10,000 bbl. By the end of the year III producing wells were completed, with an average depth of 3600 ft., from the Detroit River formation of Devonian age. The entire development of the field to the end of 1941 was on 20-acre spacing. Headquarters Field.—The Headquarters field, which lies along the line between Clare and Roscommon Counties, was one of the most important discoveries of 1941 and will be the scene of vigorous development during 1942. Production so far has been from the Traverse lime at about 3400 it., and development has indicated that this is probably one of the most productive Traverse pools yet discovered. One well had been given a potential of 10,000 bbl. per day. Dry holes well located in relation to big producers indicate that it is a typical Traverse development. Winterfield Field.-This field, in Winter-field township, Clare County, was discovered late in 1940. By December 1941, 14 Dundee and 5 Traverse producers had been completed. The Dundee lime is found at a depth of 3750 it. and the Traverse lime at 3070 it. Producing conditions in the Dundee seem to be erratic because of varying porosity in the dolomit-ized limestone. Kawkawlin Field.—The Kawkawlin field, which was discovered by the Gulf Refining Co. in 1938, is in Monitor and Kawkawlin townships, Bay County. Small production

Jan 1, 1942

By Yinchang Wang

1. INTRODUCTION 1. Subject, and Scope The formation of the oxidized ores of zinc has been recognized as a subject of great importance in economic geology. For many years these ores have been much sought, partly because they are more desirable for metallurgical treatment and partly because they are apt to be freer from gangue than is the sulphide of zinc. Up to very recent years the oxidized ores were the principal source of the metal and at present they still furnish a large portion of the commercial production. . The oxidized ores of zinc include six minerals, as shown in the-following table

Jan 9, 1915

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By AIME AIME

HENRY DAYTON WILDE-"Date," informally- manager- of the technical and research department of the Humble Oil & Refining Co., was born at Aguascalientes, Mexico, Sept. 25, 1900. He is a graduate in chemical engineering: M.S. from the University of Texas and I Sc.D. fro111 the Massachusetts Institute of Technology. t For a year and a half in 1926 and 1927 he was a research : associate in the research laboratory of applied chemistry at M.I.T., under W. K. Lewis. In the latter year Dr. Wilde went with the Humble as head of the laboratory experimental division of its refining development department. In 1929 he was made director of production research. Dr. Wilde is the author of important papers in the TRANSACTIONS of the Institute, wherein are also mans dis-

Jan 1, 1938