Search Documents

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By B. N. Das, J. B. Darby, P. A. Beck, Y. Shimomura

A POWDER pattern for the (Cr, Mo, Co)R-phase annealed at 1200°C was reported in 1951.1 Through the courtesy of Prof. D. P. Shoemaker of Massachusetts Institute of Technology the authors became aware of inconsistencies of this pattern with that to be expected from the structure of the R-phase, as determined by Komura, Shoemaker, and Shoemaker.' In addition, Professor Shoemaker also noted that the powder pattern reported8 for the (Cr, Mo, Co)D-phase, annealed at 1300°C, agreed fairly well with that to be expected from the newly determined structure of the R-phase. In view of these findings, the previously reported powder patterns of the R-phase and of the D-phase were compared carefully. It was found that most lines in the two patterns (22 lines) were to a fair degree of accuracy related to each other by a single conversion ratio for the corresponding d spacings. The value of the conversion ratio was found to be 1.0058, so that the d spacings of the D-phase pattern previously reported were larger than the correspond- ing d spacings for the reported R-phase pattern by approximately that factor. The intensity relationships between corresponding lines in the two patterns were similar, as judged visually. The following exceptions were noted: Lines Nos. 2, 3, 19, 20, 21, 22, 23, 24 and 25 of the D-phase pattern,:' all designated weak or very weak, were missing in the apparently somewhat fainter R-phase pattern used.' Lines 1, 2, 3, 5, 15 and 34 (all weak or very weak), reported for the R-phase, were missing in the D-phase pattern, Table I. In view of these observations it seemed probable that the two patterns differed from each other mainly by a slight change in lattice parameters (with c/a remaining approximately constant), and that the pattern previously reported for the R-phase contained some weak extraneous lines, most likely to be attributed to impurities. In order to check the foregoing assumption, two specimens of an alloy containing 43 pct by weight of cobalt, 41 pct molybdenum, and 16 pct chromium, which was within the composition range of stability of both the D-phase at 1300°C and of the R-phase at 1200°C, were homogenized at 1200 and 1300°C, respectively, and quenched. X-ray diffraction patterns of the powders of these two specimens, obtained with CrK radiation, were compared carefully with each other and with the D-phase pattern previously

Jan 1, 1959

By Richard H. Hopkins, R. W. Kraft

A new technique facilitating the rapid determination of the three-dimensional morphology of phases suspended in an opaque matrix is described. The vapidity of the technique is based upon continuous cinephotomicrographic recording of specimen microstructure as the specimen surface is removed under controlled conditions in an electrolytic cell. The advantages of the technique for determining spatial morphologies in opaque materials are illustrated by application of this method to the study of the configuration of faults in a specimen of directionally solidified CuAl2-Al eutectic alloy. A spatial model of the eutectic fault network deduced in this manner has substantiated the facts that faults in this alloy tend to lie parallel to one another in a direction close to that of the specimen growth axis and that the majority of faults tend to bridge lamellae rather than run parallel to them as growth proceeds. For the specimen studied fault density decreased as growth proceeded. ALTHOUGH metallographic observation is a powerful tool for investigating the correlation between structure and properties in metallic alloys, ordinary metallographic methods suffer the fundamental limitation that any conclusions concerning the three-dimensional structure of these opaque materials must rely upon inference from two-dimensional microsections. For this reason it is frequently impossible to make valid judgments regarding the true spatial distribution of the micro-constituents in specimens under investigation. Several techniques have been devised to circumvent the basic limitation of planar microsec-tioning and employed with varying success. These include construction of three-dimensional models of alloy microstructure from sequences of photomicrographs,1-3 quantitative deduction of spatial features based upon statistical studies of data from random and/or selected plane microsections,4-6 and selective dissolution of one phase in a two-phase alloy to reveal the topography of the phase remaining.' However these techniques also have certain obvious disadvantages. Construction of three-dimensional models is a very time-con- suming procedure due to the tedious polish-etch-photograph cycle needed to obtain the necessary photomicrographs to portray the spatial microstructure. Statistical methods by their very nature give only average values of the quantities being studied and cannot therefore give a detailed physical picture of the microstructure to be observed. Finally, the technique of selective dissolution is only applicable in systems where the phases are of vastly different chemical reactivity; it is of little use in the study of single-phase alloys. Since the determination of the three-dimensional structure of opaque materials is hindered by two facts—the materials are opaque to radiation in the visible spectrum and construction of spatial models of microstructure is quite laborious—two solutions to the problem suggest themselves: 1) use radiation of energy great enough to render the alloy transparent, i.e., some microradio-graphic method, or, 2) devise a rapid means to section and record alloy microstructure. Stereomicroradiography has indeed been used to study internal arrangements of phases in several materials8,9 but the method, in general, is limited to very thin specimens (due to X-ray absorption) and simple microstructures. It would seem then that development of a rapid, simple, and generally applicable technique for studying the details of alloy microstructures in three dimensions can best be undertaken by following the second approach above. Using this idea a new technique for rapid evaluation of spatial microstructures was developed based upon cinephotomicrographic recording of the micro-structure of a specimen undergoing controlled electrolytic dissolution. It was further felt that application of this technique to the careful study of the spatial configuration of faults in a CuAl2-Al eutectic alloy would yield information that could be correlated with the extensive data3,6,10-12 already compiled concerning the solidification and crystallography of this eutectic. The practicality and usefulness of similar methods for studying three-dimensional features in alloys has recently been illustrated by the study of dislocation loops in zinc13 and spheroidized structure in steel.14

Jan 1, 1965

On the following pages are abstracts of papers published by the Institute during the year 1932 as Technical Publications, Preprints, in bound volumes and in Mining and Metallurgy. For abstracts of papers that appear in bound volumes in 1932 but that were published as Technical Publications in 1930 or 1931, see the Transactions for those years. Papers that appear in this volume are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 309. Volume numbers are given as listed on page 3 and in the paragraph at the beginning of the index, page 315. The abstracts are grouped as follows: Page Page Metal Mining.................... 265 ferrous Alloys)................. 279 Milling and Concentration......... 268 Coal Division.................... 287 Iron and Steel Division............ 270 Petroleum Division............... 292 Nonferrous Metallurgy (Reduction Nonmetallic Minerals............. 299 of Ores)....................... 277 Mining Geology.................. 301 Rare Minerals and Metals......... 279 Mining Administration (Accounting, Institute of Metals Division (Found- Taxation, Industrial Relations). . 304 ing and Metallography of Non- Geophysical Prospecting........... 304 Metal Mining The Mineral Industry. By Scott Turner. (Min. & Met., June, 265. 3500 words.) Abstract of an address delivered before the Royal Canadian Institute, Toronto, April 16, briefly outlining the importance of mining in the United States, in Canada, and in the world. Comparison is made of the mineral production for 1886, 1900, 1910, 1920 and 1929, showing that in the 43 years from 1886 to 1929 that of the world increased nearly tenfold, of the United States over twelvefold and of Canada thirtyfold, but that Canada's output was equivalent to only 2 per cent of the world total and to 5 per cent of that of the United States in 1929. Statistical tables and graphs show value of production, percentage of world production contributed by Canada and the United States, etc. The mining situation in Canada is briefly reviewed: only those American engineers who have had occasion to examine the figures appreciate the rapidity of growth of Canadian mineral production. The treatment of minerals involves vast complex industries. When we are producing, say, 6 billion annually, the employment of 2 million workers provides indirect support to perhaps 10 million people. Exploiting mineral deposits is peculiar in certain ways, for the deposits are exhaustible, are of rare occurrence when measured in terms of outcrop area compared to total earth area, and may suddenly be handicapped or superseded by new discoveries; moreover, the economic position of the contained metals is 'affected by the use of scrap metal and the existence of invisible stocks. The largest and most valuable of the mineral deposits are not the metals, but rather the fuels. The record of the coal industry in recent years is one of brilliant technical achievement; its economic position is far from satisfactory. A so-called world fuel

Jan 1, 1932

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred ,at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed ,as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By E. Buehler, H. J. Levinstein

The temperature ranges in which the three inter-metallic phases in the Nb-Sn system form have been determined and the composition and structure of two of the three phases has been established. The kinetics of the formation of Nb3Sn in cored wire samples has been studied in the temperature range of 800° to 1050°C. From 800°to 950°C the rate of formation increases by four orders of magnitude. The rate-controlling step for the formation process in this temperature range appears to be the diffilsion of tin through NbSn. At higher temperatu~es a change occurs in the mechanism of the formation process such that up to a temperature of 1050°C the rate of formation of Nb3Sn does not increase above the rate observed at 950°C. For temperatures helow 950°C the current-carrying capacity of the wire increases with increased percent reaction reaching a maximum value when the formation process is 90 to 95 pct complete. The maximum current-carrying capacity obtainable in this temperature range is independent of the temperature. Above 950°C tlze current-carrying capacity obtainable in the wire decreases with increasing temperature of formation. A model is proposed which accounts for the ohserved behavior. RECENTLY, Buehler et a1.l reported the results of an investigation of the process variables which influence the superconducting properties of Nb3Sn-cored wire. These results indicated that at least four variables affect the properties of the manufactured wire. These include composition, particle size of the starting powder mix, temperature of heat treatment, and time of heat treatment. In order to understand completely the role of these variables, it is necessary to have an accurate knowledge of the phase equilibria in the Nb-Sn system. At the present time, phase-equilibrium diagrams for the Nb-Sn system have been published by a number of investigators.2-5 The diagrams differ as to the number of phases present, the composition of the phases, and the temperature range of stability of the phases. The present investigation was undertaken in order to resolve these differences. Since the investigation of Buehler et al. demon- strated that the length of time at the temperature of heat treatment affected the superconducting properties of Nb3Sn, it is apparent that it is necessary to understand the kinetics of the formation process as well as the equilibrium conditions before a complete understanding of the system is possible. As a result, the kinetics of formation of the various phases in the system were also studied in this investigation. EXPEFUMENTAL PROCEDURE Diffusion couples and sintered powdered compacts were employed in the phase-diagram investigation. The diffusion couples were made by filling 1/8-in.-ID monel-sheathed niobium tubes with tin. The monel sheath was employed to facilitate drawing.' The tubes were then drawn to a tin-core diameter of 32 mils. Samples approximately 3 in. long were then cut from the drawn composite. The tin was drilled out of the ends to a depth of 1/4 in. and niobium-wire plugs were inserted into the ends and peened over. The monel was removed by etching in concentrated nitric acid, after which the samples were sealed in evacuated quartz bulbs and heat-treated in a resistance-wound tube furnace. The samples were quenched into ice water upon removal from the furnace. The diffusion couple samples were examined metallographically employing a chemical etching solution consisting of 10 ml of saturated chromic acid per g of NaF. In addition, two anodizing solutions were used for phase-identification purposes. The first was the picklesimer7 solution; the second consisted of equal parts by volume of 30 pct H2O2 and concentrated NH4OH to which 1 g of NaF was added per 25 ml of solution. The anodizing conditions for the second solution were 2 v and 100 ma with a tin cathode. The powdered compacts were made by pressing previously mixed powders of 99.9 pct pure Sn and 99.6 pct pure Nb supplied by the United Mineral Co. into cylinders 3/8 in. in diameter by 1/2 in. long. The cylinders were then sealed in quartz tubes and heat-treated in the same manner as the diffusion couples. The samples were examined metallographically and by X-ray diffraction techniques. Since it was desirable to be able to correlate the kinetic data with current-carrying capacity, the type of specimen chosen for this part of the investigation had to be a compromise between the optimum system for studying kinetics and one which was suitable for making current-carrying capacity

Jan 1, 1964

By P. N. Richards, M. K. Ormay

Commercially hot-rolled low-carbon steel strip may have one of two basic types of orientation texture, depending upon the amount of a iron which was present during the finishing passes. The changes in these textures with varying amounts of cold reduction up to 95 pct have been determined for the sheet surface plane and for parallel planes down to the mid-plane. The development of cold reduction textures has been reassessed on the basis of (200), (222). and (110) stereographic pole figures and pole density or inverse pole figure values. In agreement with the literature, it is shown that the textures can be described in terms of partial fiber textures but alternative descriptions are given for one of the fiber textures, in order to more closely correlate with experimental data. One partial fiber texture consists of orientations of the type (hkk)[011] extending from (100)[011] to {322}(011) in agreement with the literature. At moderate amounts of cold reduction, a second partial fiber texture forms with a <331> fiber axis inclined 20 deg to the sheet normal and a range of orientations centered on one close to (1 11)[112] and reaching to (232)[101] or (322)[011]. An alternative description involves a (111) fiber axis parallel to the sheet normal but capable of rotation about the rolling direction with rotation about the fiber axis. ORIENTATIONS developed in low-carbon steel strip after cold reduction are of commercial importance because they control, in part, the final preferred orientations after subsequent annealing. The method of control however is not understood completely. Some preliminary work indicated that the cold-reduced orientations and the subsequent annealing textures of commercial low-carbon steel were dependent on the orientations present in the material before cold reduction, that is, those present in the hot-rolled strip but, to date, the effects of initial orientations have not been extensively investigated. For this reason, much of the information given in the literature on development of preferred orientation is difficult to assess as details of initial texture and processing conditions are often inadequate or are altered by a subsequent heat treatment such as normalizing.&apos; It is known2 that anomalous results for near surface orientations may be obtained if lubrication during cold rolling is not adequate but whether lubricant was used during the experiments has not always been given, nor has the exact depth below the surface at which determinations have been made. A comprehensive review of cold rolling textures has been made recently by Dillamore and Roberts&apos; and more restricted recent reviews are due to stickels4 and Abe.5 Based largely on the experimental work of Bennewitz,1 reviewers have accepted that the preferred orientations produced on cold reducing low-carbon steel can be described in terms of two partial fiber textures as follows: Partial Fiber Texture A which has a (011) direction in the rolling direction and includes orientations within the spread from (211)[011] through (100)[Oll] to (211)[011.]; there is some controversy as to whether it extends as far as the orientation (111)[011]. As Dillamore6 has observed, the extent of this partial fiber texture depends on the intensity levels selected. Partial Fiber -texture B which has a (011) direction located 60 den from the rolling direction in the plane containing the rolling direction and the sheet normal. There are two directions which satisfy these conditions and orientations in this partial fiber texture extend from (21l)[0ll] through (554)[225] to (121)[101]. The orientations {211}(011) are members of both partial fiber textures A and B and it can be noted that a variant of {554)<225> is within 6 deg of a variant of {111}(112). Barrett7 had postulated earlier that, in addition to orientations which would fall into partial fiber texture A, a true fiber texture with a (111) direction in the sheet normal was present after heavy cold reduction. This fiber texture would include orientations such as {111}(011) and {111}(112). Later investigators, notably Bennewitz,&apos; have discounted this, mostly on the ground that the partial fiber textures A and B, as described above, contain all the strong orientations that have been observed. However in other work it has been reported2 that (222) pole density or inverse pole figure values show a continuing increase with increasing reduction by cold rolling and give values considerably greater than for any other low indices plane. Thus it could be inferred that a (111) fiber texture as described by Barrett would be one which becomes more dominant with increasing cold reduction, whereas Bennewitz&apos; concluded that components such as {554)(225) in partial fiber texture B began to decrease in intensity at high reductions. Following Bennewitz, one would expect a decreasing (222) pole density value (parallel to the sheet normal) with increasing cold reduction. Because fiber textures consist of grains with a range of orientations that have one axis in common, it has been inferred that during deformation the crystal orientations rotate about the fiber axis&apos;74 and that the orientations of crystals that at one stage belong to one fiber texture can rotate on further cold reduction into the other fiber texture through an orientation in which the two fiber textures intersect.&apos; For example,

Jan 1, 1970

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

By Warnie Flint

PERSONAL INJURY ACCIDENTS According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. NO one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, but not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

By Matsubara, A.

THE problem of the equilibrium between iron, carbon, and oxygen was first carefully investigated by E. Baur and A. Glaessner,1 who determined the equilibrium conditions of the two reactions Fe304 + CO ? 3FeO + C02 (1) FeO + CO ? Fe + C02 (2) within the range of temperature of 350 to 900° C. The next series of investigations was made by R. Schenck and his co-workers,2 who sought to check the results of Baur and Glaessner&apos;s work within the range of 550° to 700° C. and to elucidate the conditions of formation of iron carbide. The equilibrium conditions at the higher temperatures, however, are generally understood to be much more complicated, owing chiefly to the formation of solid solutions between iron, its oxides, and carbide; nevertheless their determination is of much more practical importance than those at the lower temperatures. It is well known that each of the reactions is reversible; equilibrium is established when the partial pressure of oxygen in the gaseous phase has become equal to the dissociation pressure of magnetic oxide in equation 1 and that of ferrous oxide in equation 2. These equilibria are subsequently designated by "the Fe304-FeO equilibrium" and "the FeO-Fe equilibrium," respectively. As the Fe304-FeO equilibrium has three phases with three components, it must be bivariant. But the reaction involves no pressure change in the gaseous phase, hence the final composition of the latter is practically unaffected by pressure. To know, the equilibrium conditions, the compositions of the gaseous phase at different temperatures must be determined. At the higher temperature, however, iron and its oxides dissolve one another in various proportions forming solid solutions; in many cases the content of oxygen in the solid phase becomes a new independent variable.

Jan 2, 1921

By Mark J. Klein

The creep of 043 was studied over the temperature range 1650" to 3200°F and over the stress range 3000 to 44,000 psi. The steady-state creep rate over this range of stress and temperature can be expressed by the equation where A is a constant, is the stress, and is -0.8 x 103 psi-&apos;. Over a narrow range of stress variations c0 a and for this proportionality n varies from 3 to 30 in accordance with the relation n = aB. Above about 2400° F, H, the apparent activation energy for creep, is 110,000 cal per mole, a value about equal to that estimated for self-diffusion in this alloy. Below 2400°F, H increases with decreasing temperature reaching a value of -125,000 cal per mole at 1700° F. In this temperature region, H appears to be a function of the interstitial concentration of the alloy. MOST of the detailed creep studies of dispersion strengthened metals have been concerned with metals having fcc structures. However, there are a number of important refractory alloys with bcc structures that derive part of their high temperature strength from an interstitial phase and whose creep behavior has not been well defined. This paper describes the creep behavior of the bcc alloy, D43, over the temperature range 1650" to 3200°F (0.4 to 0.7 Thm) and over the stress range 3000 to 44,000 psi. In addition to colum-bium, this alloy contains 10 pct W. 1 pct Zr, and sufficient carbon (-0.1 pct) to form a carbide dispersion throughout the matrix of the alloy. The effects of variations in temperature and stress on the steady-state creep rate of this alloy are presented in this paper. EXPERIMENTAL PROCEDURES Creep tests were made in a vacuum of 106 torr under constant tensile stress conditions using a Full-man-type lever arm.&apos; Creep specimens were machined from 0.020-in. D43 sheet (grain size -5 x l0-4 in.) processed in a duplex condition (solution annealed -2900°F, 40 pct reduction in area, aged 2600°F). The specimens were tested in this condition without further heat treatment. Specimen extensions over 1-in. gage lengths were continuously recorded using a high temperature strain gage extensometer. Differential temperature and stress measurements were used to determine temperature and stress dependencies of the creep rate. Activation energies were calculated from the changes in strain rate induced by abrupt shifts in the temperature during constant stress creep tests. The 100°F temperature shifts used in most of the activation energy determinations required 15 to 90 sec depending upon the temperature at which the shift was made. The dependence of strain rate on stress was determined by measuring the change in strain rate for incremental stress reductions during constant temperature tests. It has been shown that columbium-base alloys such as D43 are susceptible to contamination by gaseous interstitial elements during vacuum heat treatments.&apos; In this regard, it is unlikely that these alloys can be heat treated without some loss or gain of interstitial elements despite the precautions taken to control the heat treating environment. However, several factors suggest that changes in interstitial concentrations of the specimens during testing did not affect the results presented in this paper. First, the dependence of the creep rate on the stress or temperature determined during the course of a single creep test showed no variations with the duration of the test. A variation would be expected if a loss or gain in interstitial concentration during the course of the test affected results. In addition, precautions taken during this investigation to minimize interstitial contamination by wrapping the gage lengths of the specimens with various foils2 (Mo, Ta, W) did not produce a detectable change in the stress and temperature dependencies relative to the unwrapped specimens. The averages of duplicate analyses for carbon and oxygen in several specimens determined before and after creep testing are listed in Table I. The combined nitrogen and hydrogen concentrations which were ordinarily less than 50 ppm did not change in a detectable way with creep testing. The analyses show that only minor changes in carbon concentration occurred during creep testing except for specimen 4. This specimen which was tested at 3100°F lost a significant amount of its carbon concentration to the vacuum environment. Specimen 1 gained 100 ppm of O, while specimens 2, 3, and 4, which were tested at progressively higher temperatures, lost increasing portions of their initial oxygen concentrations during testing. RESULTS AND DISCUSSION The Temperature Dependence of the Creep Rate. The apparent activation energy for creep, H, was de-rived from creep curves similar to that shown in Fig. 1. Steady-state creep was rapidly attained at the beginning of the test and with each change in temperature. This behavior suggests that the alloy rapidly attains a stable structure with each shift in temperature or that the structure is constant throughout the test. Since the dispersion will tend to stabilize the structure, the latter is probably the case. The activation energy was found to be independent of the direction of the temperature shift and the magnitude of the shift (50" or 100°F). Although H was approximately independent of the strain, there was a tendency for it

Jan 1, 1970

BASIC open-hearth slags have no obviously unique features when compared with slags from other metallurgical operations. Open-hearth slags form and exist at temperatures ranging from 2500 to 3100 F (1370 to 1700 C). In the course of an open-hearth heat, the liquid slag changes slowly and continuously in chemical analysis-the changes reflecting changes in temperature, changes in metal analysis, solution of charged materials, solution of feed additions, and solution of refractories. Throughout the process, the slag performs specific primary functions that are responsible for a large measure of the technical and economic importance of basic open-hearth steelmaking. It is intended in this chapter to present the chemical reactions by which the primary functions of basic open-hearth slags are carried out, to describe the physical and chemical principles governing the extent to which these reactions proceed and can be regulated, and finally to indicate the limitations imposed on other features of the process by the fulfillment of the primary functions. Basic open-hearth slags perform three primary functions. First and foremost, the slag provides a means of removing phosphorus from the liquid metal. The ability to remove phosphorus is largely responsible for the widespread use of the basic open-hearth process. Second, the slag serves as a controlling factor in transferring the oxygen required for the other oxidizing reactions. Third, the slag provides a means of eliminating some sulfur from the open-hearth bath. While the extent of sulfur removal is not comparable to that of phosphorus, the ability to remove some sulfur contributes much to the value of the process. The effectiveness with which the slag fulfills its functions varies with temperature and composition. Since operating temperatures are fixed largely by the specified nature of the product and the equipment, .the speed and extent to which the functions of the slag are carried out depend largely on its composition. The necessity for regulating slag composition to accomplish the re-

Jan 1, 1964

By R. C. Mahon

During the early history of the Lake Superior district, tamarack timber was used almost exclusively in the wines. It had the strength and lasting qualities necessary for a satisfactory mining timber. But about fifteen years ago the tamarack trees were attacked by a blight which killed nearly all of them so today no tamarack timber is available. Hemlock, spruce, and poplar have neither the necessary strength nor the lasting qualities for mining timber, but a large supply of maple and birch is available. These have ample strength but, when placed underground, fail by decay in about three years. This means that, instead of replacing the timber sets once in fifteen years, it must be done five or more times in the same space of time which involves not only incraesed timber costs but more important, an increased labor cost.

Jan 1, 1949

By Frederick M. Becket, Russell Franks

In a recent article,l which described the softening effect of columbium in plain high-chromium steels, the authors stated that their investigations had shown columbium to be also a particularly valuable inhibitor of intergranular corrosion in steels of the 18 per cent chromium, 8 per cent nickel type. It is the purpose of the present paper to record some of the results obtained through the introduction of columbium to the austenitic chromium-nickel steels. The damaging effects of this type of corrosion have become so widely known as to restrict considerably the applications of the steels under consideration, and therefore there is little question of the importance of the goal to be attained. Numerous contributions concerning the susceptibility of the austenitic chromium-nickel steels to intergranular corrosion have appeared during the past few years, and among others who have dealt constructively with the subject are such well-known authors as Strauss and Houdremont of Germany, Hatfield of England, and Bain in the United States. Different theories have been propounded as to the cause of intergranular corrosion, and various remedial measures have been proposed, the majority of which involve the use of addition agents. Titanium is the addition agent at present most generally employed, as suggested by Houdremont and modified as described by Bain, Aborn and Rutherford. Little has been published on the effects of holding these steels for long periods at the relatively lower temperatures in the presence of corroding media, and the effects have mot been fully realized by producer and consumer.

Jan 1, 1934

By D. Beregekoff

In the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

By William E. Ford, Edward Salisbury Dana

I. Sul~harsenites, Sulphantimonites, etc. In these sulpho-salts, as further explained on p. 320, sulphur takes the place of the oxygen in the commoner and better understood oxygen acids (as carbonic acid, H2COs, sulphuric acid, H4S04, phosphoric acid, H3P04, etc.). The species included are salts of the sulpho-acids of trivalent arsenic, antimony and bismuth. The most important acids are the ortho-acids,

Jan 1, 1922

By O. C. Wheeler

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February of those two years, but the manuscripts were held until released for publication in 1945. 1942 Lack of transportation facilities during 1942 resulted in a sharp curtailment of producing operations in Colombia at the middle of the year, and production of crude for export was thus greatly affected. Total production in 1942 amounted to only 10,617,008 bbl. Of this amount the Tropical Oil Co. produced 9,453,995 bbl., which includes 126,607 bbl. of petroleum condensate, and the Colombian Petroleum Co. produced 1,163,013 bbl, from its Barco property. The following summary, showing a comparison of the number of barrels of crude produced during the years 1941 . and 1942, reflects the extent to which producing operations were reduced during 1942: These above figures do not include any production recovered from Condor&apos;s (Shell&apos;s) Casabe wells during testing operations. An active exploratory drilling Program was carried out by several of the major companies, and the year 1942 established a record for wildcatting activity in Colombia. Excluding development operations on the Shell&apos;s Casabe wells on the Yondo concession, 13 wildcats were completed. Eight of these were in the Magdalena Valley, and all were abandoned; five were on the Barco Concession, and of these four were completed as producers. Particularly notable among the petroleum developments during 1942 was the continued success of drilling operations on the Shell&apos;s Yondo Concession of Compania Colombiana de Petroleos El Condor opposite Barranca-Bermeja. In 1941 the discovery well, Casabe No. I, was drilled and completed with an estimated initial production of approximately 480 bbl. of 19 1/2 A.P.I. gr. oil per day. In 1942, seven stepouts from the discovery well were successfully completed with initial production ratings ranging from 150 to 1230 bbl. per day. An extensive wildcat program on the Barco Concession of the Colombian Petroleum Co. yielded favorable results with the completion of four producers in the Socuavo and Tres Bocas areas; a fifth test, Sardinata Norte No. I, was abandoned at 500;" feet. Wildcatting operations in the lower Magdalena Valley area were initiated in 1942 With the drilling of a deep test, El Dote No. I, by Compania de petroleo Shell de Colombia. The well was a failure and was abandoned at a depth of 10,046 (?) feet. Wildcats on which drilling operations were being conducted at the end of the

Jan 1, 1945

The work of the Committee on Industrial Preparedness* is well summed up in the following letter written by Thomas A. Edison, Chair-man of the Naval Consulting Board, after President Wilson and signed the army appropriation and army reorganization bills: "The Committee on Industrial Preparedness of the Naval Consulting Board, of which committee Howard E. Coffin is chairman, after a five months&apos; campaign in many ways unique in vigor and vision has played a very definite part in the measures for the national defense which have just become law. It is responsible for having laid the foundation for a true industrial preparedness in this nation. "Five months ago the committee, wholly non-partisan in make-up, acting with the civil, mechanical, mining and electrical engineers and the chemists of the country, members of five great scientific bodies, began its work in&apos; every nook and cranny of the land. The purpose was to prepare American industry efficiently to support the armed forces of America in the event of war. "The public, the business men and the legislators at Washington knew little regarding the demands on industry in connection with modern war. No department at Washington was charged with the duty of coordinating the needs of the army and navy with transportation, industry, and kindred functions. The purchasing, quartermaster&apos;s and ordnance departments of the army and navy were unable to buy military supplies except by competitive offering in the open market. No one had considered the need, and no legislative machinery was in existence, for preventing the presence of skilled workers on the fighting front when they would in time of war be needed in the factories, mills and mines of the country. Neither at Washington or elsewhere was there even a list of the industrial resources of the nation in such shape as could be used for practical purposes in case war should come. "The three things, then, that the committee headed by Mr. Coffin set out to do and that now have been brought about were as follows: First, to mobilize concretely the business men of America and their output against a day of need. This meant chiefly to discover in fullest detail just what equipment our manufacturers possessed that might be swung over to supply the army and navy swiftly and bountifully from the hour the colors were raised. In a few weeks this initial task, which has been a truly colossal one, will be at an end. A complete report of the equipment of practically every concern of substantial size in the country is now in the hands of the - committee. Directly in charge of the great inventory has been W. S. Gifford, Supervising Director of the Committee. The second step was to procure legislation making possible the placing by the war and navy departments of annual orders for munitions in small quantities to American manufacturers now not producing such things, so that quietly, efficiently and thoroughly they could learn in time of peace how to supply the government in time of war. The new laws make all this possible. It should be said here that this practice will bring about a geographical diffusion of munition plants all over our country, instead of affording us only a few such concerns for the most part near the exposed seaboards, as at present. It is obvious that this system will also throttle all talk of a munitions trust.

Jan 10, 1916