Search Documents

By R. J. Greaves

High-resolution seismic reflection profiling can be used to evaluate detailed structural and stratigraphic features of coal prospects. Since most coal prospects are relatively shallow, less than 1000 m (3000 ft) deep, high sampling rates in space and time can be used effectively to improve vertical and lateral resolution of seismic data. The case study presented here shows how seismic data was used to evaluate the Wyodak coal at a prospective coal gasification site. The data were used to map the detailed structure and thickness of the coal and to search for lateral discontinuities, such as pinchouts and faults. An important find was a paleochannel cutting across the base of the coal seam, which was later confirmed by drilling.

Jan 1, 1986

By N. A. Warner

Dense cylindrical specimens of artificial hematite were reduced in hydrogen over a range 0-f total pressures between 0.1 and 1.0 atm and temperatures between 650" and 950°C. Hydrogen reduction at a total pressure of 1.0 atm in the presence of a chemically inert diluent and reduction in hydrogen/water mixtures were also studied Znter.face movement during reduction was followed using metallographic techniques. Substantiu1 partial-pressure gradients are shown to exist in both the gas film and the reduced iron layer. The results are consistent with a mixed-control mechanism involving an interaction of gaseous-difusion effects with a first-order reversible chemical reaction at the iron/wüstite interface. Over the hydrogen-pressure range of 0.1 to 1.0 atm, the rate is not directly proportional to the hydrogen pressure in the bulk gas stream. Nitrogen dilution of the reducing gas masks the true effect of hydrogen partial pressure by influencing the effective molecular dif-fusivity and gives an apparent first-order relationship. The transport of hydrogen and water vapor across the iron layer is consistent with molecular gaseous diffusion rather than a Knudsen diffusion mechanism. ALTHOUGH the literature on the reduction of iron oxides is very extensive, it is only comparatively recently that a definite quantitative model for the reduction of hematite has been proposed. This development has been largely due to the work of McKewan. An extensive literature review of previous work has recently been compiled by Themelis and Gauvin. Exclusive control by gaseous diffusion in the reduction of hematite has been recently advocated by Kawasaki and coworkers.' Although the results of the latter workers are of considerable practical significance, the extreme porosity (approximately 30 pct) of their specimens precludes their application to a kinetic evaluation of the reduction of dense polycrystalline hematite. The salient features of the kinetic model used by McKewan for the gaseous reduction of dense hematite at temperatures in excess of 560°C (when FeO is stable) are: 1) The reduction is a topochemical reaction taking place through 'the series FeO/FesO4/FeO/ Fe; 2) The gas-solid type of reaction takes place only at the FeO/Fe interface and the internal reduction: FeO proceeds by solid state diffusion; 3) The iron layer formed is quite porous and offers negligible impedance to gaseous diffusion; 4) The rate-controlling step in the reduction is a chemical process occurring at the Fe/FeO interface. In view of the relatively fast reaction rates involved when hematite is reduced in a stream of hydrogen, it seemed possible that the simplifying assumptions of negligible diffusional resistance in both the bulk gas phase and the reduced iron layer could introduce serious errors in the interpretation of experimental reduction data. The present work was initiated to elucidate the effect of gaseous diffusion on the reduction rate and to determine its possible influence in the formulation of the reaction mechanism at the metal/oxide interface. EXPERIMENTAL Procedure and Apparatus. Dense cylindrical compacts of artificial hematite were prepared by sintering pressed compacts of reagent-grade ferric oxide, containing 99.6 pct FezO, in air at 1200°C for 80 hr. The resulting compacts had a final porosity of less than 2 pct and a height and diameter of approximately 1 cm. Variations in sintering atmosphere from air to pure oxygen, in sintering time from 20 to 80 hr, and temperature from 1150" to 1250°C had no effect on the subsequent reduction behavior. The reduction of the samples took place in a vertical tube furnace in which was placed a 1-in. transparent silica tube. The 24-in. heated length

Jan 1, 1964

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33' API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle coal at the rate of 200 tons a day. By 1860, revolving screens were in wide use in the Pennsylvania anthracite field. Shaking screens were introduced in the Pennsylvania anthracite region in the 90's and they rapidly displaced the lower-capacity revolving screens.

Jan 1, 1950

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,' these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton' have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth's magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By Robert Mehl

THE precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstätten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe,P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. PRECIPITATION OF FE4N FROM ALPHA SOLID SOLUTION OF N IN ALPHA FE Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kaupp1 and by Lehrer2 have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591° C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

By Samuel Daniels

The Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such condition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400" to 600" F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400" F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600" F., the Al-Cu-Fe-Mg alloy at about 700" F. The former starts to reharden at 700" F., the latter at 800' F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500" and of 700" F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500" and 700" F. Although the latter can be made harder initially than the Al-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. Certain aluminum alloys have been used for pistons and other parts operating at temperatures up to 650" F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance to corrosion. In the piston, the inertia forces and the bearing loading, and with this the vibration, are decreased. The piston head functions at a lower temperature (about 200" F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design. The range in analyses of aluminum alloys, used for pistons in domestic and in foreign internal-combustion engines is shown in Table 1. There seem to be three general types of composition; one containing about 10

Jan 1, 1926

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By H. H. Rachford, and J. D. Rice

The effectiveness of digital computing machines in making technical calculations depends on how well the work is arranged to utilize the capability of the machines. This note presents a particularly useful way of calculating hydrocarbon vapor-li.quid equilibrium in the flash vaporization (or condensation) system. The method is well suited to sequence-controlled computing equipment. It is not limited to equilibrium calculations and may be used for solution of most implicit equations in one variable. INTRODUCTION There is increasing interest in the use of electronic digital computers in research and engineering calculations. This is a fortunate and inevitable trend in view of both the increasingly extensive numerical work which is becoming a routine part of many daily production operations and growing demand for the overwhelming amounts of calculations required by newly developed numerical methods for solving heretofore unsolved problems. Machines are in many ways ideally suited to the task but of necessity present certain difficulties. for a particular poblem to be solved must often be formulated quite differently from the way it would be arranged for manual solution. This is done in order to take advantage of the inherent speed and precision of electronic computers and at the same time to limit the need for number storage to the capacity of the machine. Therefore, this note is submitted to present a general and quite powerful method of finding solutions of the frequently encountered implicit equation: F(x,y1,y2,...ya)=0.......(1) where the root, x, is to be found for a given set of y1, ... yn.. The procedure is well suited for use with computing machines, for it usually requires but little storage or programming beyond that necessary to evaluate F. HYDROCARBON EQUILIBRIUM The method is described in terms of the problem it was designed to solve, i.e., the calculation of hydrocarbon vapor-liquid equilibrium in flash vaporization. Given the composition of a hydrocarbon mixture and appropriate values of the equilibrium ratios K, to find the phase ratio and compositions in a closed system: let z, be the mol fraction of the i-th component in the mixture. If K, is the ratio yl/xl, where y, and x,

Jan 1, 1952

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.'' The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.' At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

J. T. Pullon, Rowangarth, Roundhay, Leeds, England :— In discussing Mr. Lee's paper, I wish to call attention to the fact that Mr. B. II. Thwaite (who was heard here yesterday on the subject of the application of blast-furnace gas for the production of power, of which he was undoubtedly the pioneer) read, at the Engineering Congress in Glasgow in 1901, a paper on the profitable utilization of power from blast-furnace gases,' in which he suggested the diversion and cleaning of the whole of the waste gases coming from the blast-furnace and their utilization for power-production, so as to obtain, with proper manipulation, from 4 to 6 times the efficiency of present methods. He suggested also the heating of the stoves with producer-gas of a higher and therefore more suitable calorific value, so as to maintain them in a constant state of maximum efficiency, free from dust, and to avoid the irregular working of the furnace, besides obtaining a maximum supply of air-blast, of 15 or even 20 lb. pressure, by means of internal-conibustion blast-engines driven by the cleaned waste furnace-gases, with a surplus of gas left for other uses. Since that time, in view of the necessity of having a stand-by plant, immediately available, in case of strikes or other reasons causing the banking or blowing-out of the blast-furnace, he has developed, as an addition to his other types of producer, a high blast-pressure gas-generator, producing a gas identical with, or somewhat superior to, blast-furnace gas; and in which all the ash of the fuel is turned into fluid slag, which is available for, the production of slagwool. The gas is a little richer in carbon monoxide than average blast-furnace waste gas, and has only from 1 to 3 per cent. of hydrogen. Fig. I, drawn from a photograph, shows a plant containing this generator, now in operation at Leeds. It is made in units of from 1,000 to 10,000 h.p. capacity for each vessel, and coupled,

Jan 1, 1907

By C. E. Sims, C. A. Zapffe

MANY hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel,105 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlement is due to hydride formation does not conform to the known facts.104 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel. A second widely discussed hydrogen-caused defect is the "flake" or "shatter crack." Although it is generally agreed that the presence of hydrogen is a prerequisite for their appearance, it is also realized that internal stress plays a decisive part. The relationship of hydrogen to internal stress has not been explained very clearly; nor is it always clear what the relationship is between a "flake" and a "snowflake," or between a "fish eye" and a "shatter crack." More importantly, the relationships among hydrogen embrittlement, hydrogen-caused fissures such as "flakes" and the ultramicroscopic structure of steel have scarcely been recognized. The present investigation attempts to provide an explanation for the embrittlement of steel by hydrogen by showing cause for accepting the "block" concept of metal crystals, and then to show how the numerous hydrogen-caused defects are interrelated in the light of this concept. EVIDENCE OF SUBSTRUCTURE IN METAL CRYSTALS It appears that the concept of a crystal as an aggregate of smaller multi-atom units must be accepted in some form if the behavior of metals is to be understood. The abundant literature on the evidence of an ultramicroscopic "mosaic" structure in metals and other crystalline substances suggests that the physicist has provided the metallurgist with an invaluable new insight. The exact picturization that any one physicist provides may be open to question, but the fact that there is some such fundamental substructure seems undeniable. The present work makes no pretense of comprehensively treating the imperfection structure theories. Nor will conclusions be drawn here regarding the exact nature of the substructure of crystals. However, the acceptance of some imperfection theory of fundamental attributes seems so necessary to an understanding of the behavior of hydrogen in steel that the following brief

Jan 1, 1941

By C. E. Lesher

Low-TEMPERATURE carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus 3/8 -in- or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal, of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic con-sumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold.

Jan 1, 1940

By L. S. Austin

I. Introduction............ 431 II. Organization............ 432 III. Production............ 434 IV. Transportation............ 435 V. Sampling..........436 VI. Concentration............ 440 VII. Blast-Furnace Plant........... 442 1. Construction........... 442 2. Operation............ 450 VIII. Advantages of Large Furnaces........ 455 1. Saving in Fuel........... 455 2. Saving in Jacket.Water..... 455 3. Quick and Large Discharge of Matte and Slag... 455 4. Decrease of Incrustation... 456 5. Elasticity of Operation..457 6. Large Flow Through Fore.Hearths...4. 57 7. Alterations Without Interruption..458 8. Variations in the Composition of Slag....458 9. Less Labor-Cost.......... 458 10. Less Initial Cost.......... 460 IX. Briquetting.Plant........... 460 X. Roasting-Plant............ 462 1. Kilns............ 462 2. Reverberatory Furnaces...468 XI. Converter-Plant........... 474 1. Construction ..........474 2. Operation.......... 476 XII. Flues and Stacks........... 478 XIII. Arsenic-Plant............ 480 XIV. Coke-Washing Plant.... 452 XV. Slime.Ponds ........... 483 XVI. Brick-Plant............ 484 I. Introduction. The Washoe plant; in Anaconda. Mont., together with the local street-railroad, ranches. a foundry and machine-shop. A

Jan 1, 1907

By R. E. Smallman

R. E. Smallman (University of Birmingham, England)—Recently, Tedmon and Ferriss11 have determined the yield stress parameters oi and ky for tantalum by measuring the lower yield stress as a function of grain size 2d and fitting the results to a relationship of the form They report that although ky , which is taken to be a measure of the dislocation locking strength, is small (- 2 to 4 x 106 cgs units) a substantial yield drop is nevertheless observed in a normal tensile test. Niobium gives a similar result,12-14 as pointed out in the original work by Adams et a1.,12 and in order to check this apparent anomaly the yield-stress parameters of electron beam-melted niobium have recently been reanalyzed15 by the Luders strain technique. In this method the strain hardening part of the stress-strain curve is extrapolated to zero plastic strain; the intercept on the preyield portion of the curve is taken to give oi, whilst the difference between oi and the lower yield stress gives kyd-1/2. The results indicate that ky increases with increasing grain size and hence, a plot of vs d-112 yields an apparent ky, which is lower than the true value. A similar effect could account for the small ky found in the relatively pure tantalum used by Tedmon and Ferriss. The variation of ky with grain size shows that dislocations are more strongly locked in coarse-grained specimens than in fine-grained samples. In niobium, this may be attributed to the fact that the dislocation density in the fine-grained material is higher than that found in the coarse-grained samples which are given a sufficiently prolonged anneal to remove any residual substructure and, since the metal contains only a small amount of interstitual impurity, a variation in locking occurs. By contrast, application of both the grain size analysis and the Luders strain method to yield-stress data from commercially pure vanadium containing a large amount of interstitial impurity gives consistent values of oi and ky, with ky independent of grain size and temperature. Electron microscope observations show minor variations in dislocation density from grain size to grain size, but in any case in this material the dislocations are heavily locked with precipitate. On yielding new dislocations are generated and, as a consequence, the importance of any differences in dislocation density between the various specimens of different grain size is considerably reduced. It is perhaps significant that Adams and lannucci,16 working with a grade of tantalum containing a higher interstitial content than that used by Tedmon and Ferriss, prepared the specimens of different grain size by annealing in the temperature range 1500" to 2000° C to minimize any differences in dislocation structure, and found that ky had a value of 1.04 x 107 cgs units, independent of testing temperature. Such behavior is consistent with the dislocations being locked by carbide precipitates so that the generation of free dislocations is an athermal process. The recent work of Gilbert et al.17 also shows that in tantalum there is no significant variation of ky with grain size provided it contains 150 ppm of oxygen. In this case, however, the dislocations are not locked by precipitate and ky is temperature dependent. C. S. Tedmon and D. P. Ferriss (authors' reply)— We would like to thank Dr. Smallman for his interesting comments and discussion to our paper, "The Dependence of Yield Stress on Grain Size for Tantalum and a 10 pct W-90 pct Ta Alloy".18 It was suggested that perhaps the relatively small values obtained by us for ky of tantalum could be attributed to the same cause that accounts for the apparently small values of ky that result when it is determined by the Luders Strain technique. Since our values were obtained by plotting the lower yield stress vs the reciprocal of the square root of the grain size, it is not clear how this could be the case. The values of ky in this experiment have been calculated, using the Luders strain technique. With this method, values for ky on the order of 2 x 105 to 5 x lo6 cgs units were obtained. In spite of this rather large variation, the magnitudes are still small, and there appeared to be no good correlation between ky and the grain size or the yield stress, probably because of the difficulty in accurately extrapolating the work-hardening portion of the curve back to zero plastic strain. As was shown in the original data,18 there was little work hardening in any of the curves, at any temperature. In his discussion, Dr. Smallman also points out how ky has been observed to increase with increasing grain size, when determined by the Luders strain technique. There are at least two possible explanations for this. In the first case, if it is assumed that the bulk of the interstitial impurities are concentrated at the grain boundaries, then, of course, the available grain boundary area would decrease with increasing grain size, thus presenting less area for the interstitials, which would then presumably increase the concentration within the grains, thereby increasing the locking of the dislocations. In the second case, the increase in ky with increasing grain size would be attributed to the nature of the grain boundary itself. One of the several ways of deriving the Hall-Petch equation19 is based on the stress concentration arising from a pile-up of dislocations at the boundary. The ability of the stress concentration to unlock a source in a neighboring grain would depend on the strength of the grain boundary. As is well-known, the nature and struc-

Jan 1, 1963

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948