Search Documents

By Michael Tenenbaum, C. C. Brown

IN recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual estimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly[$] suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its application. FACTORS INVOLVED IN MEASURING pH OF WATER-SLAG MIXTURES To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading are reviewed individually in the following paragraphs. EFFECT OF COOLING RATE Under actual operating conditions there can be considerable variation in the tem¬perature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By J. E. Tobey

BECAUSE of the wide-spread publicity given to Nylon yarn as being made from ?coal, air, and water,? the general public has become conscious of the nonfuel uses of bituminous coal. Some of these uses are as filler for fertilizer, carbon for the absorption of orders, for water supply, and for the bedding of cattle. Spectacular as are these accomplishments the fact is that only a small amount of coal is used for nonfuel purposes. It is on the utilization of coal as fuel that the industry depends. Practically all the coal mines for years to come will be used for making coke for the generation of heat. Recently much attention has been paid to the significance of ash in coal. Another study worthy the interest of metallurgists in the iron and steel industries if that of Dr, Lowry of the Carnegie Institute of Technology relative to the percentage of sulphur in coal and coke.

Jan 1, 1941

By A. P. Herring, S. F. Ravitz

Manganese dioxide reacts with sulfur dioxide solution in the absence of oxygen to form manganous ion and dithionate ion, together with a small amount of sulfate ion. The effects of SO, concentration, hydrogen ion concentration, stirring speed, and temperature on the rate of the reaction were studied. If it is assumed that undissociated SO2 molecules react rapidly with MnO, at active surface sites and that bisulfite ions react slowly, an equation can be derived that satisfactorily represents the observed reaction rates. For solutions in which the reaction with undissociated SO2 predominates, reaction rates and activation energies estimated from diffusion theory agree well with those found experimentally. Manganese dioxide dissolves readily in aqueous solutions of sulfur dioxide. The nature of the dissolution reaction was first investigated by Gay-Lussac and welter1 in 1819; they identified a new oxysulfur radical, the dithionate ion, S2O6, as one of the reaction products. Since then, the reaction has become a standard method of preparing dithionates in the laboratory and one of the more promising methods of leaching manganese from low-grade ores. In the "dithionate process" developed by the U.S. Bureau of Mines2,3, manganese-dioxide ore is suspended in a solution of calcium dithionate and leached with gas containing sulfur dioxide. The manganese is dissolved and the sulfur dioxide is oxidized according to the reactions:

Jan 1, 1965

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By J. Wyn Prior

The seismic refraction technique is probably the most popular geophysical method of bedrock profiling in geotechnical site investigations but is somewhat restricted by the inherent assumptions in the method. This paper describes how Hales' method of profile interpretation is modified to overcome the assumptions of increasing velocity and layer thickness with depth when only first arrival data is available. A further expansion of Hales' method enables presentation of refraction data in a form whereby bedrock features, such as changes in velocity, relief and dip in particular, are more readily recognized. Characteristic curves of the more common bedrock features are presented as an aid to bedrock feature recognition.

Jan 1, 1979

THE illustration below shows the design of the face of the clock to be erected as a memorial to the American engineers who gave their lives overseas in the World War. It will be placed in the tower of the library at Louvain, which has been rebuilt through contributions from America. Large clocks seldom have figures on their faces, and each hour on this one will be marked by a gold star, the four faces containing 48 stars, one for each State of the Union. Contributions toward the memorial have been received from every one of the States, and from Alaska and Hawaii as well, but additional subscriptions are invited by the Com-mittee which is arranging for the memorial.

Jan 3, 1928

By Frederick N. Rhines

Pure copper that has been allowed to oxidize at an elevated temperature in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cuprie oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig, la). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composetl of oxide particles precipitated in a matrix of metallic copper, that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,' it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but mill separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (I) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By Frederick N. Rhines

Pure copper that has been allowed to oxidize at an elevated temperature in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cuprie oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig, la). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composetl of oxide particles precipitated in a matrix of metallic copper, that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,' it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but mill separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (I) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By R. Havens, K. C. Dean, H. Dolezal

Mine, mill, and smelter wastes aggregating billions of tons are scattered across the country as unattractive barren piles that mar the natural beauty of the land. As the population of the United States increases and the demand for land intensifies, populous centers are slowly encroaching on these formerly isolated wastes. Encroachment sharply intensifies the importance of controlling the air and water pollution derived from natural weathering of such wastes. Use or stabilization of these wastes comprises the only viable means for minimizing pollution. Utilization is preferable to stabilization, because full use would both eliminate the waste and broaden the mineral resource base. However, the wastes typically comprise immense tonnages of materials discarded by selective mining or after recovering the significant mineral values by milling and/or smelting. Only rarely can such low-grade material be reprocessed to extract additional minerals at a profit. Some mineral wastes are suitable for disposal as mine fill, railroad and highway road ballast, and land fill. Similarly, some mineral wastes can be utilized as raw materials for making brick, rock wool, concrete, and ceramic products. Several means exist for stabilization of relatively fine-sized wastes, which constitute the chief sources of air and water pollution. These include physical, chemical, and vegetative stabilization, and combinations thereof. Massive coverings of coarse slag, concrete, and soil may be used to prevent erosion of waste piles. A variety of chemicals can be used to bond the particles of fine-size waste into a relatively inert mass. However, the most promising method of producing an esthetically appealing storage site is vegetative stabilization. Numerous species of plants can germinate, grow, and reseed in waste materials which have been adequately prepared to support plant life.

Jan 3, 1969

By H. Warlimont

Precipitation of cementite plates from carbon-rich austenite gives rise to localized formation of martensite in the matrix next to the precipitate upon quenching. The growth of this martensite is urmsually restricted. A distinct lattice relationship is found between this martensite and the cementite phase. It is concluded that the martensite is nacleated in the region of lowest carbon concentration at the austenite-cementite integace, with low-energy matching to the cementite lattice. The restriction of the growth of the martensite phase to the vicinity of the cementite plates can be explained by misfit in the austenite -martensite glissile interface and the uphill carbon gradient in the austenite. The investigation was carried out by light- and electron-microscopy and by electron-diffraction of thin foils. THE precipitation of cementite from carbon-rich austenite gives rise to a localized formation of martensite in the matrix next to the precipitate upon quenching. This behavior has been described previously by A. B. Greninger and A. R. Troiano1 for a 1.78 pct C steel ("pseudomorphic martensite"), and by A. Hultgren2 for a Fe-0.99 pct C—5.20 pct Mn steel. By measuring the axial ratio of the martensite phase,' it was found that the carbon content of this martensite was lower than that of the martensite which formed without prior partial transformation to cementite. Therefore, it was concluded that lowering of the carbon concentration in the matrix next to the precipitate raised the M, temperature locally and thus led to nucleation of martensite at the ce-mentite-austenite interface. However, the restriction of the growth of the martensite phase to the vicinity of the cementite plates cannot be explained by localized carbon impoverishment alone. Under ordinary conditions a martensite plate which has been nucleated in a favorable site can continue to grow until it encounters a physical barrier, or until it encounters a compositional barrier in the matrix, where the total free-energy change for the reaction is not negative, since it has been shown by numerous experiments that the activation energy for growth of ordinary martensite is virtually zero.' An investigation was conducted by transmission electron microscopy and electron diffraction to study this extraordinary martensite. It was expected that crystallographic in addition to compo- sitional conditions caused this abnormal mode of martensite formation. MATERIAL AND PROCEDURE An Fe-C-Mn alloy containing 1.15 pct C and 5.1 pct Mn was used for most of the experiments. For metallographic work, specimens 15 by 15 by 3 mm were used. For preparation of thin films, the initial specimen size was 15 by 15 by 0.7 mm. The heat treatment of each specimen consisted of austenitizing for 1/2hr at 1100'~ in an argon atmosphere, subsequent isothermal holding in a lead bath at one of a series of different temperatures, and, finally, quenching into brine at room temperature. For metallographic examination, the specimens were mounted in bakelite (slight tempering effects resulted from the heat in the mounting press) ground, polished, and etched in nital. Thin films for transmission electron microscopy and electron diffraction were obtained by grinding the specimens to approximately 0.2 mm thickness and subsequent electrolytical thinning. The orientation relationships were evaluated from sets of electron micrographs and selected-area electron diffraction patterns of single units of the transformation products and the adjacent matrix. RESULTS In the alloy which was used for the experiments, proeutectoid carbide precipitates over a wide tem-

Jan 1, 1962

By Ellsworth Daggett

Jan 1, 1879

United Engineering Trustees, Inc. GEORGE D. BARRON WILLIAM H. BASSETT R. M. ROOSEVELT The Engineering Foundation GEORGE D. BARRON H. C. BELLINGER E. DEGOLYER Engineering Societies Library Board ROBERT PEELE PHILIP W. HENRY H. K. MASTERS A. B. PARSONS, Ex-officio R. H. SWEETSER

Jan 1, 1932

Truman H. Aldrich '78 W. S. Ayres '73 Andrew A. Blair '75 Walter M. Brodie '72 H. M. Chance '74 Fred'k G. Corning '77 Ralph Crooker '81 A. W. Crookston '80 George M. Davidson '81 W. B. Devereaux '80 H. S. Drinker Founder

Jan 1, 1929

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By Linda Lee, R. E. Reed-Hill, C. R. Smeal

Four fcc metal surfaces, etched to make them responsive to polarized light, have been studied with an electron microscope. Jones'prediction that these surfaces are grooved has been verified. Optical-goniometer measurements made on commercially pure nickel indicate that the groove walls are poorly defined (100) facets. Surface mientations close to either 4001 or {ill).- show no extinctions on the polam'zid-light microscope. An explanation is offered for this orientation dependence. It has also been deduced that polarized-light extinctions on a grooved cubic-metal surface should not be used directly in crystallographic-orientation determinations. The nature of the etching solutions that produce these surfaces is considered. A cubic-metal surface may be made responsive to polarized light in two basic ways."' In one, an anodic film, believed anisotropic, is formed on the surface. A plane-polarized-light beam, at normal incidence, should be reflected from this type of film with an ellipticity that varies with grain orientation. Under crossed polarizers of a polarized-light microscope, each grain may be distinguished from its neighbors by a difference in reflected-light intensity. An alternate treatment,' more generally applicable to cubic metals and of principal concern here, involves etching of grain surfaces. The characteristic features of this surface were first deduced by Jones3 from light-microscope observations. She concluded that, in general, grain surfaces were furrowed so that light was reflected from two parallel sets of etched facets. A grooved surface produces elliptical polarization of a plane-polarized beam because the beam does not strike groove walls at normal incidence. Jones also observed that the furrows must have faces inclined to each other by approximately 90 deg, since the light returns along the incident path, and that a grooved surface should show four maxima and minima of reflected-light intensity during a 360-deg stage rotation of the polarizing microscope. Positions of maximum extinction were predicted to occur when groove axes were parallel to either polarizer or analyzer vibration directions. Because of the limited resolving power of Jones' optical microscope, her deductions were primarily indirect. Proof of the correctness of her conclu-sions, as demonstrated by the electron microscope, will be given as well as evidence concerning the crystallographic nature of the etch furrows and the types of etching solutions that produce them. EXPERIMENTAL PROCEDURE During a comprehensive study of hot plastic deformation in nickel and nickel alloys, an etch was evolved that produced a surface with an excellent polarized-light response on Nickel 200 ("A" Nickel). The etching solution and associated metal-lographic procedures are given in Table I. In evaluating this etch, a study was made of the topological features of the etched surface and their relation to the underlying crystalline structure. As part of this investigation, large crystals (2 mm average diameter) were grown in a 1-cm-sq Nickel 200 specimen. After the surface was etched, the crystallographic orientations of ten grains were determined by the standard back-reflection Laue technique of Gren-inger.4 Maximum extinction positions during a microscope stage rotation were also measured for the ten grains. Groove-wall positions on the surfaces of the ten grains were measured with a two-circle optical goniometer. The technique was essentially that of Barrett and Levenson.5 Several grain surfaces were photographed with a Philips Model 100A electron microscope. All specimens were replicated with collodion, or collodion backed with formvar and chromium shadowed at 18 to 20 deg. The basic material was Nickel 200. However, an electron-micrographic study was also made of surfaces developed by polarized-light etches on other fcc metals (90-10 a brass, Monel 400, and lead). All etching procedures are given in Tables I and 11. EXPERIMENTAL RESULTS Fig. 1 shows typical electron micrographs of three different fcc metal specimens and an optical micrograph of a fourth. All photographs show a grooved structure corresponding closely to Jones'3 predictions. Also, as noted by Jones, extinctions were always observed when groove axes were either parallel or perpendicular to the microscopes' vertical cross hair. The symmetry of the grooves, with respect to the twin boundaries in Fig. 1, implies that furrows have a crystallographic basis. The coarse-grained Nickel 200 specimen was used to study this basis. Facet Orientation. The poles of the ten Nickel 200

Jan 1, 1964

HAVING produced one ton of concentrate that contains the copper that can profitably be saved or recovered from anywhere between 3 and 60 tons of mine ore, the ore-dressing engineer passes the result of his handiwork over to the metallurgist for smelting. Essentially, the concentrate is a damp mass of finely ground material consisting of copper sulphide minerals; pyrite, the sulphide of iron; and gangue, usually silica and silicates of aluminum. The purpose of smelting is to produce metallic copper and a slag containing the iron and siliceous constituents by pyrometallurgy-the kind of metallurgy that employs fire and heat to produce the chemical reactions through which it attains its object. Though blast furnaces have been used to smelt Porphyry-mine concentrates, notably at Braden, more than 90 per cent of [ ]

Jan 1, 1933

By A. F. Nylander, J. H. Jensen

Magnesium, in its combined forms, is the sixth most abundant element and the third most abundant metal in the earth's crust, but it is so reactive that it is never found in nature in the elemental state. As part of the rock-forming minerals like magnesite, dolomite, olivine, and serpentine, it is combined in virtually insoluble forms. As part of soluble minerals like kainite (KC1 MgS04 - 3H20), leonite (K2S0, MgSO, 4H20), langbeinite (K,SO, 2MgS04), and carnallite (KC1 . MgCl? 6H20), it is found in evaporite deposits, generally of marine origin, deep within the earth's crust. Since these minerals are soluble, they are found only in deposits protected from the percolation and leaching action of ground waters by an insoluble and impermeable mantle. Usually this mantle is from several hundred to many thousands of feet thick. Finally, as a solute in marine-like brines, magnesium is common in surface and subterranean waters throughout the world. The oceans, which contain 0.13% Mg, illustrate the inexhaustible nature of the reserve. The recovery of magnesium from the rock-forming minerals, usually by thermal decomposition, and from dilute brines such as sea water by precipitation with lime, are frequent industrial practices. But the recovery of magnesium as magnesium chloride from evaporites or natural brines of concentration greater than sea water has been of little industrial significance for economic and technological reasons. The present US capacity is preponderantly based on the sea-water magnesia process with thermal reduction capacity in second place. No present magnesium capacity is dependent on recovery from the stronger natural brines. But projected capacity, although still weighted in favor of the sea-water magnesia process, is partly based on the recovery of magnesium chloride as a byproduct of potash operations.

Jan 11, 1964

By J. J. Calaman, D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast-holes in magnetic taconite at the preliminary taconite plant of .the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing machine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1. During three months of 1949 and continuously since February 1950, production piercing took place under all pit conditions. By the end of October 1950, a total of 15,000 linear ft of hole had been pierced in an open pit handling an average of 1200 to 1800 tons of crude a day in one 8-hr shift. While it is recognized that this output does not approach the millions of tons a year planned for the developing Minnesota taconite projects, the machine as a unit has been operating under conditions probably more adverse than those that eventually will be encountered in the large operations. This pilot operation has permitted evaluation of the piercing problem in the full-scale taconite plant. This paper describes jet-piercing process funda- mentals, important features of the latest jet-piercing burners and machine, actual piercing results obtained, and new developments that give promise of materially increasing overall process efficiency. To produce the blasthole, jet-piercing utilizes thermal energy, as contrasted with the application of mechanical energy in churn drills and jackham-mers. The heart of the process may be termed a tailored flame produced by a rocket-type burner, thermodynamically similar in every respect to that of the giant rockets being developed for military purposes. The heat release in the combustion chamber of the burner is about 50x10' Btu per cu ft per hr as compared with 5x10' for most modern steam generators.* Combustion of liquid petroleum fuels (kerosine, diesel oil, or No. 2 fuel oil) with gaseous oxygen in the burner chamber at pressures of 100 to 200 psi results in temperatures of about 4300°F. Expansion of the hot combustion gases through divergent nozzles produces high-temperature supersonic jets having measured velocities of about 6000 fps. Impinging the flame jets on rock causes a thin surface layer to expand and break away from the base as a result of the thermally induced stresses. This spalling action is aided further in chert and quartzite by the 0.82 pct volume change resulting from the 6 to p quartz inversion at 1066"F.t The dynamic action of the jets whisks the spalled rock

Jan 1, 1952

By Chas. A. Ashburner

THE Bradford Oil District lies in the northern part of McKean County, Pa., and the southern part of Cattaraugus County, N. Y. Although petroleum was first found in the producing sand in 1871, it was not until the early part of the year 1875 that a productive horizon was acknowledged to exist, even by those most largely interested in the production of the crude oil. It has been reported to me that the first well drilled in the valley of the Tuneangewant Creek (commonly called Tuna Creek) was drilled by F. E. Dean and brothers in 1865. This well was located on the Shepherd farm, near the present site of Custer City. One hundred and sixty feet of drive pipe was used, and the hole was drilled to the depth of 900 feet. The producing sand at Custer City is found about 1130 feet below the level of the railroad track. The Shepherd farm well was therefore abandoned over 200 feet above the top of the oil sand. The next well was drilled by the Dean brothers on the Clark farm at Tarport. Drilling was stopped at a depth of 605 feet, or over 400 feet above the top of the oil sand. In the year 1862 the old Bradford well, since known as the Barnsdall well, was drilled to a depth of 200 feet with a spring pole, and then abandoned. In the spring of 1866 the citizens of the village of Bradford concluded to club together and sink the Barnsdall well deeper. It was drilled to a total depth of 875 feet, or to within 150 feet of the Bradford producing sand. All of these wells were drilled with the expectation of finding the Venango County oil, and at

Jan 1, 1879