Search Documents

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,' the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson's investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.'s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By Edwin S. Sperry

Metals differ widely in their behavior under the cuttingtool. Some, like iron or steel, require a slow speed and light feed, a tool shaped differently from that used for other metals,

Jan 1, 1898

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing' for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing's correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine's multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

By H. M. Chance

STRETCHING from New York southwestwardly to Georgia is a great range of hills and mountains consisting of pre-Palaeozic schists, slates, and gneissic and granitoid rocks, known locally by many different names; in Pennsylvaniaa as the South mountains, the Berkshire or Durham and Reading hills, and in Virginia and farther south as the Blue ridge. To the northwest of this range lies the " Great Valley," underlain by Lower Silurian limestones, and known as the Lehigh valley, Cumberland valley, Shenandoah valley, valley of Eastern Tennessee and Georgia and by other local names, but all these are parts of one valley, geologically and geographically continuous from New Jersey to Georgia. Lying upon and along the northern flank of this range of mountains, and dipping northwestwardly under the limestone of the valley, is the Potsdam formation (Primal or No. 1 of the Pennsylvania Geological Survey), which consists of sandstone or conglomerate overlain by slates. The latter are sometimes arenaceous and occasionally are replaced in part by sandstone. This formation varies from a few feet to several hundred feet in thickness. At the outcrop the slates are completely decomposed, oxidized or disintegrated, forming a belt of clay several hundred feet wide occupying the interval between the outcroppings of the sandstone and limestone. This clay-belt includes a more or less continuous series of iron-ore (brown hematite) deposits, which have been, and still are, extensively worked. The belt is more or less continuously mineralized with iron throughout its length, and hundreds of large deposits of ore have been developed and worked, producing many millions of tons of ore.

Sep 1, 1908

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS. ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Fergusson, V. Bir¬mingham, Aldrich, T. H., Jr, Bowron, C. E, Bowron, J., Davis, F H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E, McCormack, G B., McCrery, Ramsay, E, Shook, A. M. Ensley, McDonald, S., Shook, J. W. Gadsden, Lee, R. H., Jr. Gannts Quarry, Hiller, E Helena, Squire, J. Huntsvalle, Moss Le¬high, Toulmin. Ozmoor, Greenamyer, A. G. Rock Run, Garvin, J M. Selma, Saylor, B. F. A. Sheffield, Miller, D, I. Tuscaloosa, Lodge, J. Woodward, Wood¬ward, A. H. ALASKA Coppermount, Wiswell, H. J. Douglas Island, Macdonald, J Ellamar, Stevens, B. Fairbanks, Hamilton, A L Haines, Le Wald, E A. Jualin, Hoggatt, W. B. Juneau, Denby, Hampton, W. H , Thane, B L , Whipple, J. R. Ketchikan, Bar¬ber, J C , Parker, J. L., Reid, G D Nome, Garfield, C D. Snettwham, Tisdale. Teller, Hirshberg, M. R. Treadwell Caty, Kinzie, Stow, H. P. Valdez, Esterly, G. M, Hazelet.

Jan 1, 1910

By H. H. Podgurski, F. N. Davis

In silver alloys containing less than 0.2 wt pet Cu. the reaction 9 + 1/2 0, = CuO(s) was found to proceed to equilibrium between 700o and 808oC. From measurements of the equilibrium dissociation pressures of the CuO at several temperatures, the differential heat of solution and the activity coeflicients for copper in silver were calculated. These values were found to be in reasonable agreement with those calculated from data appearing in the literature. A metastable "copper oxide" with an atom ratio of oxygen to copper as high as 1.7 was formed by internal oxidation at 300°C of these same dilute Ag-Cu alloys. No anomalous behavior was noted in the temperature dependence of oxygen solubility in silver. The solubility minima between 300" and 800°C reported several years ago can be accounted for, at least in part, by reactions with trace impurities, such as copper. Cold-worked siloer exhibits an enhanced permeability to oxygen. THIS investigation was undertaken because of our interest in interactions between solute and lattice defects in metals. The reason for the choice of the O-Ag system for study is the anomaly in the solubility of oxygen in silver reported by Steacie and Johnson1 in 1926, specifically that isobars between 100 and 800 Torr show solubility minima at 400°C. It was also claimed that the copper impurity in the silver was not responsible for the minima. Recently, Eichenauer and Müller2 proposed that surface adsorption might have been responsible for this solubility anomaly, but no adsorption isotherms are available to check the pressure and temperature dependence observed at the low temperatures. Surface-tension measurements on silver made by Buttner, Funk, and udin3 suggest that a considerable fraction of a monolayer of oxygen exists on silver at 922°C and at an oxygen pressure of 150 Torr. To account for the pressure sensitivity reported by Steacie and Johnson1 at 300°C, the oxygen bound to the surface at 922°C cannot be considered relevant; the existence of a surface layer at 300°C characterized by a lower energy of binding would be required to explain the effect. All of our attempts to detect an interaction of this type with surface sites have failed. In this investigation we have not been able to associate the dissolution of oxygen in silver with a dislocation interaction. Evidently, severely cold-worked silver does not contain a sufficient number of trapping -sites for oxygen. Indeed, our work shows that oxidation of trace impurities in the silver was probably responsible for Steacie and Johnson's results. In addition, we have been able to establish the nature of the reaction with copper impurity in silver by thermodynamic considerations. EXPERIMENTAL PROCEDURE Measurements of both the internal oxidation rates and the solubility were made volumetric ally in a system equipped with a gas burette, a mercury manometer, a McLeod Gage, and a mass spectrometer. The silver and the silver-alloy samples were protected from contamination by mercury vapor from our pressure gages by suitably placed refrigerated (-78°C) traps. Silica reaction vessels were employed for experiments performed above 500°C. Spectroscopically pure gases were used in this investigation. The highest-purity silver used in the solubility measurements was 99.999 pet. By chemical analysis 2 ppm of Cu were found in this silver. The two Ag-Cu alloys used in this research were made up to 0.14 and 0.15 wt pet Cu starting with 99.999 pet Ag. An unexpected source of error was discovered in the course of the work. At temperatures near 800°C silver distilled from the hot silica reaction tubes into cooler regions of our system. Although the weight loss of silver from the sample was not important in itself, oxygen was being consumed by the silver distilled into the cooler part of the system to form a stable oxide phase from which the oxygen was not recovered. In a separate experiment conducted to determine the necessary correction, losses between 0.2 and 0.3 cu cm (stp) of 0, in 24 hr were measured at 810°C. On the assumption that the flux of silver from the vessel to form Ag2O de-

Jan 1, 1964

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By E. F. Raffo

THE design of the Chuquicamata concentrator offered an unusual combination of problems, all of which had, in one way or another, a definite effect upon the final arrangement of all the equipment and necessary facilities. First of all, a remotely located project of this magnitude required careful selection of equipment with an adequate supply of replacement parts and in some cases necessitated stand-by spare equipment ready for immediate use. Fortunately, in the course of determining the proper flowsheet, in itself a prime factor in the concentrator design, it was possible to conduct numerous grinding and flotation tests at the Anaconda and Andes concentrators. As a result of these tests made under actual operating conditions, most of the major equipment best suited for treating the Chuquicamata ore efficiently was decided upon while preliminary design layouts were still being made. The design has been based primarily on the treatment of sulphide ore crushed to about 3/4 or 1 in. However, until the new sulphide crushing plant is completed it will be necessary to handle ore crushed to 3/8 in. in the existing oxide crushing plants and to some extent a mixed ore which has had its oxide copper content removed by leaching. This mixed ore, known as leached residue, will contain a certain amount of sulphuric acid from the leaching process which necessarily requires special protective measures. Several factors influenced the final location of the Concentrator. The only established fact known during preliminary design layout was the elevation of the dumping floor over the fine ore bin. This was predetermined by the desired level railroad grade across part of the existing tailing and leached residue dumps from the oxide plant to the bin. Next it was necessary that a site be chosen that would not require an excessively long haul from either the present oxide plant or the mine and in addition provide a fairly constant natural ground slope sufficiently wide to accommodate the length of the ultimate concentrator. The site as finally chosen to meet the foregoing restrictions provided a natural ground slope of 6 to 7 pct. This was excellent, especially in a region subject to earthquakes, as it assured that foundations of heavy equipment and footings for building and crane columns would rest on cut or undisturbed ground. However, this shallow slope, although having some definite advantages in the overall consideration of plant layout, resulted in the need for extensive studies in the general arrangement of equipment. Wasteful and excessive vertical drops had to be eliminated in the

Jan 1, 1952

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By G. T. Smith, R. C. Moyer

L. P. DAVIDSON*—In the analysis of the cadmium sponge how is the sample prepared ? M. M. NEALE*—The analysis of the cadmium sponge? L. P. DAVIDSON—You gave a very high percentage of metallic cadmium, 2 pet zinc, 2 pet lead and say 93 pet

Jan 1, 1950

By J. F. Emig

The Burns Harbor Plant was designed to produce and process large ingots into plate, hot rolled sheet, cold rolled sheet and tin plate. Rimmed ingots, in particular, are poured 96" to 106" high and weigh up to 85,000 lbs. During the latter part of 1970, a quality problem was encountered involving white line "sliver" defects on the surface of cold rolled, low carbon, rimmed steel sheet. Sheets containing these defects are not desirable for exposed automotive items because of the possibility of opening during forming or becoming more apparent after forming. Metallographic work located and identified two basic types of inclusions within the white line defects: (1) complex oxides consisting largely of iron and manganese oxides and (2) scale-type iron oxide. The presence of these oxides strongly suggested that the-white line defects were resulting from an unsound, unclean rim zone.

Jan 1, 1972

Major William R. Grunow, in a brief account off his military services, says: "I take pleasure in informing you that since my return from France I have been stationed at Camp A. A. Humphreys, Va., and am now on duty as a Senior Instructor at the Engineer Officers' Training School. While in France, I served as a company commander in the 305th Engineers and was later ordered to return to the United States for assignment to new troops. Upon arrival in the United States, I received my majority." P. F. Rodegerdts gives us the following account of his military service: "I enlisted in the Naval Reserve Flying Corps in San Francisco on Feb. 12, 1918. On February 10, I was ordered to Cambridge, Mass., where I was enrolled for the course in technical aircraft construction given at Massachusetts Institute of Technology. After successfully completing the course of instruction, I spent six weeks in practical construction of seaplanes at the Curtiss aeroplane factory in Buffalo. Following this, I was assigned to active service at Akron, Ohio, on June 22, 1918. At the same time I received my commission of ensign U.S.N. R.F. Unfortunately, I have been kept at Akron and although I have made

Jan 1, 1919

By R. E. Ogilvie, H. C. Gatos, R. E. Hanneman

The ejj-ect of high pressures on chemical inter-diffusion in the Fe-V system was determined by analyses of concentration vs distance profiles of atmospheric and high-pressure diffusion couples. Diffusion data were obtained as a function of tern -perature and composition. Activation energies, activation volumes, and frequency factors were determined at 1 atm, 20 kbars, and 40 kbars as a function concentration in the a and y phases. The A great deal of research has been carried out in the measurement and understanding of binary chemical inter diffusion in solids. Studies of the effects of high pressure on interdiffusion in binary systems, however, have been virtually nonexistent until the present work. This paper gives a detailed account of the effect of high pressure on interdiffusion and the Kirkendall effect in the Fe-V system. The present data are compared to existing theo- Kirkendall effects were measured at 1 atm and 40 kbars. At 1 atm Dy > DFe at the marker concentration; however, Dv approaches DFe under pressure, and at 40 kbars the values are approximately equal. The high-pressure and atmospheric diffusion data are evaluated on the basis of theoretical models. Chemical analyses of the diffusion -couple profiles were made using an electron microbeam probe. retical treatments of pressure dependence of diffusion which are based upon self-diffusion studies. THEORY The rates of atomic migration in metals and alloys are regulated by the repulsive forces exerted on an atom during its motion from one equilibrium lattice site to another and by the availability of a jump site. Application of high pressure is expected to decrease diffusion rates because it decreases interatomic distances as well as defect concentrations. A number of theoretical treatments have been focused on the problem of calculating self-diffusion coefficients in solids under atmospheric pressure. In general, the vacancy mechanism of diffusion appears to be dominant at high temperatures in most metallic systems. The migration of an atom by this

Jan 1, 1965

By John G. Hall

The unstable metal market during 1949, with resulting lower metal prices, has focused every mine operator's attention on the problem of reducing operating costs. Improvement in mining, methods, use of modern mechanical mining equipment, and increasing the efficiency of the labor force are the tools with which we will have to work. Careful planning is necessary to coordinate all phases so that no one phase is overdone. A mine may become over-mechanized if, for instance, capital charges against new equipment exceed the savings in labor costs, or where a large enough tonnage is not produced. The cooperation, of labor is essential to any mechanization program. There have been too many instances where mechanization and improvements have done nothing more than make up for a decrease in labor efficiency, thus bringing the production of labor back to its old standard. The operator has gained little and labor has gained only a "softer job." In any mechanization program there are gains to be had by both the operator and labor. By the efficient application of modern equipment and improved mining methods the operator should gain by decreased costs, and labor may profit by receiving a share of these decreased costs.

Jan 1, 1950

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By F. Valton

(Read at the Wilkes-Barre Meeting, May, 1877.) IN the number of the Engineering and Mining Journal for April 7th, 1877, Mr. W. P. Ward, of Cartersville, Georgia, explains in a very interesting manner, the results he obtained in the manufacture of ferromanganese in the blast furnace. These results may be summed tip as follows : Production in the blast furnace of an alloy containing 67.2 per cent. manganese and 3 per cent. of carbon at most, with a utilization of the manganese amounting to 58 per cent. With the exception of the indicated proportion of carbon, which should be almost doubled to express the true state of facts, we would have had no observations to make on Mr. Ward's paper had he taken into account the results obtained in the same line in other centres of production. Before 1870, spiegel with 8 or 10 per cent. manganese only was known among blast-furnace products. In a journey to Sweden, in 1871, I ascertained that the Schysshyttan works manufactured regularly a spiegel with 18 per cent. manganese. Later, at the Vienna Exhibition, in 1873, the Sava and Jauerburg works, in Carniola, presented to the jury a ferromanganese, obtained in the blast fur-

Jan 1, 1878

By N. B. Davis

I. Introduction. II. Definition of Plasticity. III. Theories of Plasticity. A. Structure of the clay particles. (1) Fineness of grain. (2) Plate structure. (3) Interlocking particles. (4) Sponge structure of particles. B. Presence of hydrous aluminum silicates. C. Molecular attraction between particles. D. Presence of colloidal gelatinous matter. (1) Review of theory of colloids. (a) Suspension colloids. (b) Emulsion colloids. (2) Experiments. IV. The Formation of Clays. A. Residual clays. B. Transported clays. V. Summary. VI. Conclusion. I. IntRodUction While working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity. This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 1, 1915

By G. L. Oldright, F. W. Schroeder

Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may he considered that the improvements made were due largely to increases in the size of the furnace used. Doubtless some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928