Search Documents

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss's original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By T. V. Subrahmanyam, A. P. Rao

The adsorption behavior of chalcopyrite has been studied at different xanthate concentrations and flow rates in a column apparatus with potassium ethyl xanthate as the collector. Based upon the experiment results an equation of the type: 1/F = K3 + m3C + k2/t.Cm2.fm1 is proposed to account for the experimental data. Among copper minerals an early study on chalcocite by Gaudin and Schuman (Taggart, 1951) is well known for its research on the kinetics of the reaction by conventional method of mass balance between the products of reaction and xanthate consumed. The results were interpreted by the concept of ion exchange adsorption. Szeglowski (1977) conducted measurements on the adsorption of potassium ethyl xanthate on copper polarized to various potentials, the adsorption being measured by radio-tracer techniques. The adsorption in the range -1800 to 700 mv was found to be a reversible physical adsorption. The potential range in which the primary electrode process could lead to surface coverage with a minimum number of product layers was evaluated. The adsorption density of xanthate on sulfide surface was found to be related to the concentration of xanthate in solution and concentration of depressants as: [ ]

Jan 1, 1983

By M. C. Lavine, H. C. Gatos, R. S. Mroczkowski

The structure of GaAs-Ge heterojunctions prepared by a back-melting process was studied by X-rav diffraction, melallographic, and electron-micro-analyzer techniques. The boundary region between the GaAs and the germanium was found to consist of a four-layered band. A discontinuity between the two inner bands was brought about by solidification occurring simultaneously from the GaAs and the germanium side. The junction material OH either side of the central discotinuity was found to have grown as a single Crystal with the orientation of the parent substrate. It was found essential to determine the GaAs-Ge phase diagram. This was accomplished by a series of alloys containing 0 to 40 wt pet GaAs. Over this range the diagram is a simple eutectic with the eutectic point at 74 wt pet Ge and 845 C. The limiting- solubility of Coils in germanium was found to bc less than 5 wt pet. The Kossel divergent-beam X-ray technique was used to study orientation relationships across the boundary lager. A great deal of effort has been recently expended on the electrical properties of heterojunctions. Little attention, however, has been given to the metallurgical variables which may be of importance in the formation of the junctions. The present work was undertaken to investigate some of the more pertinent metallurgical aspects of interface-alloyed GaAs-Ge heterojunctions. Such parameters as solidification processes, composition gradients, orientation effects, and the accommodation of crystal structures have been the objects of study in this program. EXPERIMENTAL PROCEDURES Phase Diagram. The phase diagram of the GaAs-Ge pseudobinary system was determined by means of cooling curves. A Bridgeman furnace was employed with the center section maintained at 1200°C and the upper section at 800°C. Melts varying from 0 to 40 at. pct in GaAs content were used. Each charge was incapsulated under a two-thirds atmosphere of argon in a carbon-coated quartz tube. Five min in the furnace hot zone provided rapid melting and homogenization. The capsule was then removed to the cooler portion of the furnace. Cooling times were of the order of 3 min. The resulting homogeneous microstructure indicated that equilibrium conditions were obtained by this procedure. Formation of Heterojunctions. Rectangular parallelepiped single-crystal samples were cut with the large faces of either the (l00), (110), or (111) orientation. The remaining four surfaces were also cut to specific orientations to permit accurate relative orientation of the GaAs-Ge pairs. The

Jan 1, 1965

By Paul M. Tyler, Carle R. Hayward

DOES it pay to do really good work? Quite likely the practical millman will answer that it does not. The preparation of ores for market is primarily a business enterprise, and by and large the individual operator does not bother his head about squandering our national resources or making easier the job of the smelterman. Having accepted such ore as he may get fro111 the mine, his job is to make the best possible showing with his mill fro111 the standpoint of financial return. His success is measured in dollars and cents, and he has no rightful reason to expect more than scant acknowledgment of any other achievements from the stock- holders of his company who in the last analysis are his employers.

Jan 1, 1936

By J. D. H. Strickland, K. J. Jackson

IN previous papers' ' details were given of the constructlon and use of an apparatus to study the rate of chlorine consumption and the rate of sul- fate and sulfur production when dilute aqueous chlorine solutions were allowed to react with pyrite and galena in acid solutions at or near room temperature. The reaction with pyrite was very rapid, and hence entirely transport-controlled in its kinetics, and produced only ferric and sulfate ions. The behavior of galena was much more complex and was studied in some detail. Sulfur monochloride could be detected as a reaction product and both

Jan 1, 1959

By J. Menashi, D. A. Douglas, A. S. Rappas

Aqueous solutions of Na2Cr04 are reduced with CO to produce hydrous Cr2O3 and NaHCO3/Na2CO3. CH3OH, HCOO- and HCHO in the presence of CO2 also reduce Cr(VI) and yield similar products. It is shown that the rate of Cr(VI) reduction can be represented by the expression -d [Cr(VI) ]/dt = k[Cr(VI)]0.5[R], where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mol (43,000 Btu per lb mol). Rapid reduction rates are attained at temperatures in excess of 220°C (428°F). With these three reductants, a green acid-insoluble readily filterable hydrous Cr203, is formed. With HCHO, significant reduction of Cr(VI) occurs at about 80° to 100° C (176° to 212° F). The product is an acid-soluble violet modification of hydrous Cr203. Solutions of Na2CrO4 contaminated with Mo(VI) and W(VI) can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels.

Jan 1, 1986

A New Microscopy and Its Pntentialities. By Charles S. Barrett. (Metals Technology, .April 1945) Physical Metallurgy Fundamental Principles Involved in Segregation in Alloy Castings. By R. M. Brick. (Metals Technology, Sept. 1944) A Stud) of Age-hardening Using the Electron Microscope and Formvar Replicas. By D. Harker and MI J. MurphyI (Metals Technology, June 1945) Standards for Identifying Complex Twin Relationships in Cubic Crystals. By C. G. Dunn. (Metals Technology, April 1945) Orientation Changes during Recrystallization in Silicon Ferrite. By C. G. Dunn (Metals Technology, April 1945) The Orientation Texture at the Surfacr of Cast RIetals. By Gerald Edmunds. (Metals Technology, Jan. 1945) (With discussion) Internal Friction of Single Crystals of Brass, Copper and Aluminum. By George H. Found. (Metals Technology, June 1945) (With discussion) Recrystallization of Aluminum in Terms of the Rate of Nucleation and the Kate of Growth. By W. A. Anderson and R. F. Mehl (Metals Technology, Feb. 1945) (With discussion) Copper and Copper-rich Alloys Textures, Anisotropy and Earing Behavior of Brass. By F. H. Wilson and R. ill. Brick. (Metals Technology, June 1945) (With discussion) Phantom Laminations in Brass. By Daniel R. Hull, H. F. Silliman and John R. Freeman, Jr. (Metals Technology, Jan. 19451 (With discussion) Corrosion of Yellow Brass Pipes in Domestic Hot-water Systems—a Metallographic Study. By E. P. Polushkin and Henry L. Shuldener. (Metals Technology, Oct. 1944) (With discussion) The .Alpha Solid Solution Field of the Copper-manganese-zinc system. By R. S. Dean, J. R. Long, T. R. Graham and .%. H. Robersori. (Metals Technology, June 1945) A White High-manganese Brass. Ry K. S. Dean, J. R. Long, T. R. Graham and C. W. Matthews. (Melds Technology, June 1945) Magnesium Alloys Oxidation Inhibitors in Core-sand Mixtures for Magnesium Castings. By O. Jay Myers. (Metals Technology, Feb. 1945) (With discussion) Grain Size and Properties of Sand-cast Magnesium Alloys. By R. S. Dusk and C. R. Phillips. (Metals Technology, Feb. 1945) (With discussion) Rater Quenching of 'Some Typical Magnesium Casting Alloys. By R. S. Busk and R. E. Anderson (With discussion)

Jan 1, 1945

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

IN a previous article' the authors outlined a study of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam .opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report' were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated. Data from the second series are recorded in Table I. Listed in the first three columns are the independent variables of feed rate (1000, 2000, 3000, 4000, and 5000 1b per hr), mill speed (50, 60, 70, 80, and 90 pct of critical), and pulp density (50, 60, 70, and 80 pct). The dependent variables, Pso, P100, reduction ratio, slope of the log-log sieve analysis curve, power demand, and Bond work index follow. Of these, only the reduction ratio and the Bond work index were analyzed for significance. Production of new surface as calculated from sieve analyses has not been included for this series because of the questionable assumptions that have to be made to satisfy the formulas involved. The large number of products obtained during the runs precluded the use of surface measurement techniques by the gas adsorption methods at this time; however, samples of all products have been stored for future reference. To test the consistency of the reporting of the sieved products, an averaged sieve analysis was calculated from the wet-dry plots obtained from the three product samples of each run. The resulting averaged analysis was plotted and the P80, selected. The relative deviations of the P80's from each of the three product samples with respect to the P80 of the averaged analysis were then calculated. In only two sets were the relative deviations (6.2 and 9.9 pct) considered excessive. In each of these two sets, one sieve analysis was obviously out of line; hence that analysis was ignored and new averages were computed. This reduced the relative deviations to 1.2 and 2.7 pct respectively. The relative deviations of the product analyses with respect to their averages ranged from 0.1 to 1.4 pct at 1000 lb per hr, 0.0 to 1.1 pct at 2000 lb per hr, 0.2 to 3.0 pct at 3000 lb per hr, 0.3 to 4.3 pct at 4000 lb per hr, and 0.5 to 5.2 pct at 5000 lb per hr. The relative deviation of the 80 pct passing point for 96 dry sieve analyses of the feed with respect to that of the averaged analysis was 7.6 pct. This slightly higher percentage can probably be attributed to a greater proportion of tramp oversize in a crusher product than is ordinarily found in a rod mill product. The last column on Table I lists the adjusted work index, which has been used as the measure of efficiency for the various combinations of operating conditions investigated. Efficiency increases as the index becomes lower. It was reported in the previous paper that the work indexes for the Waukesha limestone used in these experiments decreased as the product size decreased (as calculated from Bond grindabilities). That is, this limestone becomes easier to grind as the material becomes finer. This is unusual, because the work index for most materials as calculated from the Bond grindability has remained constant as the product size decreased or has increased slightly. Table II lists the results of Bond grindability tests at all mesh sizes from 3 to 200 and the work indexes calculated from them. To remove this variation of work index with product size from the data so that results would apply to any material of constant work index, the work index values shown in Table II were plotted against product size on log-log paper. From this curve (a straight line function in this case), the expected work index for the product size for each of the runs of the experiment was obtained. The work indexes as calculated from the reduction ratio and energy consumption were then divided by the corresponding expected work index. The results obtained are reported in percentages on Table I as adjusted work index and are actually percentages of the work index for the Waukesha limestone at the size in question. Multiplication of the work index value for a material of constant index by these percentages should allow the application of the adjusted work index curves to the material. Only the adjusted work index values, not the actual experimental values, were used for the variance analyses and for the graphs.

Jan 1, 1956

By W. S. Tower

STEEL is the basic metal, the main metallic prop of the modern industrial world, a good gage for measuring the state of our complex economy. Any who had doubts on that score should have had them dispelled by the many evidences of public concern over the affairs of the steel industry in recent months. I do not need to relate the various criticisms of the industry, nor the questions about its policies and performance which have come in a rising flood, especially from unthinking and irresponsible sources. But judged from the standpoint of production, or from plans to improve and expand facilities, or from technical progress, the facts about the steel industry are proof of

Jan 1, 1948

By Henry M. Howe

Jan 1, 1909

By George Fancher, R. L. Whitting

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By R. L. Whitting, George Fancher

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

Jan 1, 1969

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy' presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. 'References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,' and Carter et a1.' treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy's law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

By C. Hertzler

The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observi" a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich 11, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69% Cu vs other rock types with .70 + % Cu; 86% should be 98.6%. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness.

Jan 1, 1985

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By W. R. Ingalls

THE present administration has made sincere and effective efforts to reduce the expense of the Federal Government, but it has reached a point beyond which it seems impossible, or anyway extraordi-narily difficult, to go. This is ascribable to the large part of the budget that is represented as war expense. There is no doubt that this spells high taxation for many years to come. Nevertheless, although a large part of the taxation will be attributable to the war, the paying out of the proceeds of that taxation by the government will not be war expense, except in minor part, as will be hereinafter made clear. It will be useful to explain the economic meaning of this situation, for it has bear-ings upon several open questions, such as a bonus to the ex-soldiers, the foreign debt accounts, etc. The expense of the war on the part of the American people was in the main paid concurrently with its prose-cution. This was necessary. Warfare is not conducted with money, but with materials and labor. Except for such previous production as was represented by stocks of goods, the requirements had to be supplied by coincident production. With the end of 1918 our war expense ceased, save for such production, e.g., of ships, that was allowed to run on unchecked, and the indemnities that had to be paid for cancelled contracts. When those matters have been settled we shall be done, barring one important thing. Of course, our war expense began to contract right after the armistice and shrunk rapidly with the demobilization of the troops in 1919. If we had not been able to obtain all needful material from our own sources and had been constrained to borrow it from foreign countries, incurring a foreign debt, we should have been in the quite different posi-tion of having to repay that material, or its equivalent, during subsequent years. The European countries had to come to us for such supplies. This outlines the fundamental difference between their present situations and ours. We were therefore compelled not only to furnish materials and man-power for our own warfare but also much for the Allies.

Jan 3, 1923