Search Documents

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By A. L. Baxley

An Untapped Energy Resource As much as 20 billion cubic feet of natural gas per day are flared from remote oil fields for lack of a commercially viable means of capturing, transporting, and marketing such gas. The magnitude of these gas flares can be put into perspective from an early satellite photograph (Fig. 1) which shows lights from the major cities of Russia and Eastern Europe dwarfed by the natural gas being flared in the Persian Gulf. Together, these wasted resources contain the energy equivalent of about one-half of the gasoline consumption in the United States today (Fig. 2). Additional trillions of cubic feet of natural gas are "shut-in" because of no economically viable means of commercial recovery. Methanol and liquified natural gas (LNG) are the only two practical fuel products which can be produced economically from these gas supplies. Many of these gas supplies are less than 500 million cubic feet of gas per day, making an LNG facility uneconomic. In contrast, barge-mounted methanol plants can economically convert billions of cubic feet of gas per day into safe, clean-burning methanol. The methanol approach offers the only economical route to transform vast, known reserves of natural gas into a highly versatile primary liquid fuel. Methanol Barges: An Innovative Solution The barges will be towed to suitable offshore and upriver locations such as Alaska, South America, Africa, Southeast Asia, Australia, New Zealand, and the South Pacific Islands, as well as fields in the Persian Gulf and Mediterranean Sea. At the offshore production site, a barge will be anchored by a single point mooring buoy that will also serve as an entry point for natural gas feedstock and an offloading point for methanol (Fig. 3). At some sites the barge would be beached. Each barge will produce methanol and store it in internal tanks with a capacity of 18 million gallons. The methanol will be offloaded into conventional tankers and safely transported directly to market. Unlike LNG, methanol requires neither specially built carriers nor specially built receiving terminals. Once a particular gas field has been exhausted, the barge will be towed to another location to continue production. Each barge will measure 320 by 500 ft, approximately the size of four football fields, and will have the capacity to produce 1 million gallons or 2800 metric tons of methanol per day, from approximately 100 million cubic feet of natural gas per day (Fig. 4). The barges will use the highly successful "low- pressure" design developed by the Lurgi Company of Germany, a process proven in land-based methanol plants throughout the world during the last ten years. The decision to use Lurgi technology for "sea-trans- portable" methanol plants was based on the higher efficiency and greater operability of the technology compared to other commercially proven processes. The conversion plant will be designed to accept a wide variety of feed gas compositions, and will produce chemical-grade methanol for the broadest market base (Fig. 5). To minimize costs and construction time, the barge-mounted plants will be built in the high technology environment of a domestic or foreign shipyard. Selection of the construction site for each barge will be dictated by the location of the production site and by the relative construction costs. A number of shipyards have the capacity to build several barges per year. The detailed marine engineering to integrate the design of the processing plant with the floating platform can be performed by numerous major engineering companies around the world. Production Economics The barge-mounted plant concept not only assures large volumes of methanol, but it also keeps the overall production cost low by minimizing construction cost and providing access to low cost natural gas feedstock with no alternative or a negative value. Together, these advantages make the barge-mounted methanol plants economical today. The cost structure of a new barge-mounted methanol plant differs from that of existing methanol producers around the world (Fig. 6). For example, if a U.S. Gulf Coast producer is paying $4.70/MMBtu in 1985 for natural gas, the barge plant could afford to pay about $1.6O/MMBtu for gas and be able to deliver methanol to the Gulf Coast at the same price. At some future date such as 1990, a gas cost of $6.70/MMBtu for a domestic producer would have cost parity with about $3.60/MMBtu gas cost for the barge plant. In many foreign markets, feedstocks other than natural gas are used for methanol production (Fig. 7). For example, most of Japan's capacity is based on LNG while Western Europe uses residual oil or naptha. Because these feedstocks are substantially more ex- pensive than natural gas used by U.S. producers, the barge plants will compete even more favorably in these foreign markets. As crude oil prices rise, the value of methanol in each of these markets will increase. However, the hierarchy of methanol values in these markets should remain unchanged. Furthermore, the cost advantage for using methanol in these markets will improve as world energy costs increase since the value of remote gas should not escalate significantly.

Jan 1, 1982

By D. S. G. Hanson

The Flin Flon Mine has been in production for over fifty years, and current mining is dependent on pillar and remnant recovery. One of the last major blocks of ore, and an important economic entity to the Mine, is the North Main Shaft Pillar. A rock mechanics program was initiated through under' ground instrumentation and other subsequent analyses, to establish the degree of instability as min¬ing progressed. Several studies have been and will be undertaken to evaluate the general stability, and possibly improve the chances of stability during pillar recovery. The North Main Shaft Pillar is immediately bounded by cemented cut and fill supporting rib stopes which inturn are bounded by slag and waste filled stopes. The min¬ing method involves a modified longhole open stoping and slag fil¬ling sequence for each mining block in a general mining upwards scheme.

Jan 1, 1983

By George H. Anderson

A CHAPTER of appealing interest was added to the industrial history of the Southwest early in June, when the War Production Board gave final approval to the erection of a blast furnace, a battery of coke ovens, an ore-beneficiation plant, and other facilities for the production of pig iron in northeastern Texas, just north of the East Texas oil field. For many years the people of Texas and adjoining states have cherished the ambition and desire that eventually an iron and steel industry drawing upon local mineral resources would be established to serve Southwestern markets. The existence in this vicinity of valuable deposits of iron ore, limestone, and coking coal has been known in a general way for many years, and efforts have been made from time to time to use them in the production of iron. The present development promises to bring to realization the dreams of the men who have visualized what the establishment of this basic industry would mean to the region.

Jan 1, 1942

By H. Kenworthy, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2 with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite- type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore.

Jan 1, 1949

By William Waters Van Ness

The Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively reccnt date, were carried out in the neighborhood of the village of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E—W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposcd to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Jan 1, 1909

By Leonard Obert

The structural stability of any mine or under- ground opening in rock is dependent on the stress field, that is, the state of stress in rock before mining, the stress distribution in the rock created by the opening, and the in situ strength of the rock. In the past mine design problems have been considered by assuming that the stress field is due only to the weight of the overlying rock, the stress around the opening can be calculated from elastic theory using laboratory-determined elastic constants, and the in situ strength of the rock can be determined from laboratory tests on small specimens. Solutions to hypothetical problems using this procedure are given in a report by Obert, Duvall, and Merrill.' Because of the uncertainties of these assumptions, this method can give only a rough approximation to the solution of actual structural problems. Obviously, this approach to determining the stability of underground openings would be greatly improved if the rock stress could be measured in situ, and it is undoubtedly for this reason that in recent years many investigators have spent considerable effort on the development of procedures for measuring rock stress. In this report a method is described for determining in situ the absolute stress in rock. The method requires the measurement of the deformation of a borehole before and after the rock is stress-relieved. The magnitude and direction of the applied stresses are calculated from the borehole deformation and modulus of elasticity of the rock. Also, the results of absolute stress determination made in the walls and pillars of underground openings in five rock types are presented. From these results a number of conclusions are drawn regarding the accuracy and limitations of this method and the problem of stress measurements in general.

Jan 8, 1962

By Robert Glass Cleland

UPON the death of its founder, Phelps, Dodge & Co. entered upon a new chapter in its long and varied history. Thereafter, for nearly a decade, William E. Dodge largely determined and executed the policies of the company. The old firm, dissolved automatically by Phelps's death, was succeeded by a new partnership consisting of Anson G. Phelps, Jr., William E. Dodge, Daniel James, James Stokes, William E. Dodge, Jr., and D. Willis James, one of the three sons of Daniel James. Each of the first three partners owned a twenty-five-per-cent interest in the company, Stokes had a fifteen-per-cent interest, and the two younger partners each held five per cent. The new company bought Anson Phelps's holdings in the old firm from Olivia Phelps, his widow and executrix, for approximately seven hundred thousand dollars; but the new partnership, designed by agreement to last the usual five-year period, was brought to an end shortly before that time by the death of the younger Anson Phelps from small- pox. Perhaps because of poor health, the son had never been as deeply concerned with business as his father, but found

Jan 1, 1952

By Richard D. Hagni

Abstract-Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in mill Products. The mill dressing engineer should be more aware of the types of beneficiation problems that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations of the mineral constituents of an ore or mil1 product can be visually determined. This advantage provides solutions to many beneficiation problems. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in floculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 10, 1978

By Donald L. Colwell

THIS is a metallurgical war. More than ever before, the mechanized forces and the air-borne warfare are deciding campaigns. Both of these are primarily dependent upon metals. There are two ways of increasing the effective supply of these metals when the demand is greater than the total over-all supply. The American custom, when a shortage of anything develops, is to get more. In the case of some nonferrous metals this has been done. For example, our potential peak output of magnesium will be almost one hundred times the prewar production. Output of aluminun has also been tremendously increased, and production of other metals is being stimulated by every possible means. Our enemies, however, have another successful method of increasing the effective supply of a material, and that is, to eliminate entirely all nonessential uses, and also to use, in essential applications, alternate materials wherever possible. Sometimes, ersatz material is inferior to the original, and consequently does not do the job as well. Often, however, it has been found superior, and many substitute items are now being used both by industry and by the military which will continue even when the original material again becomes available.

Jan 1, 1943

By Charles E. Glass

A steadily growing body of evidence indicates that earthquake ground motions can cause failure of rock slopes that are otherwise stable under static loading conditions. As a result, the economic optimum working slope angle is reduced when earthquake shaking is considered in surface mine design, especially in regions of high seismicity. When designing surface mine slopes to withstand seismic motion it is as important to consider the probability of experiencing various levels of ground shaking as it is to consider the characteristics of the ground motion. For most slope designs, simple probabilistic techniques such as extreme value or maximum likelihood techniques are appropriate. These techniques, however, should be applied in such a way that a probability value is assigned to characteristic ground motion parameters at the mine rather than to nearby earthquake magnitudes. Several techniques have been developed to analyze rock slopes subjected to dynamic loads. Most of these techniques do not adequately account for the ground motion parameters of concern. The best technique appears to be one that utilizes actual earthquake time histories. A simple technique that calculates block displacement for any input accelerogram, using a linear acceleration approximation between time steps, has been developed that accurately accounts for rock block response. Results using this technique indicate that the following factors are important for assessing rock slope stability in earthquake regions:

Jan 1, 1983

By R. A. Marriot

The steam-generating plant at the Garfield smelter of The American Smelting and Refining Co. consists of two divisions in which the boilers are classed as direct-fired or waste-heat. The direct-fired boiler plant consists of eight 330-boiler hp. type K-19 and S-I 7 Stirling boilers located in the boiler room adjacent to the power house, and two 330-boiler hp. Stirling type K-19 boilers in the reverberatory building, which formerly were connected to a reverberatory furnace but now are arranged for direct firing. All direct-fired boilers are now fired with natural gas. The waste-heat boiler plant consists of all units connected to reverberatory furnaces, and receiving heat from the exit gases therefrom. In this classification there are two 490-boiler hp. Erie City vertical water-tube boilers, and six 330-boiler hp. type K-19 Stirling water-tube waste-heat boilers. Each furnace has boilers arranged in battery setting. The boilers are directly in front of the furnace and connection is made through a short uptake and flue (Fig. 1). The Stirling boiler settings rest on concrete foundations at ground level, with the furnace uptake and flue at a low elevation. The Erie boilers are carried on steelwork some 15 ft. above ground level, and stand against the face of the uptake with no connecting flue. The constructional requirements of a larger furnace dictated this type of setting.

Jan 1, 1934

By Leonard R. Weisberg

The general properties of diffusion in GaAs are reviewed. A total of .fourteen atoms have been studied to date, and activation energies for eleven reported are (in ev): Ga (5.6), As (lo), Zn (2.49), Cd (2.43), Sn (2.5). Mn (2.75). S (4.0). Se (4.2). Ag (0.33), Cu (0.52). and Li (1.0). The dijfusion of the first eight atoms, as measured by Goldstein using radiotracer techniques, established the principle of sub lattice diffusion for both host and impurity atoms, since atoms substituting for gallium have lower activation energies than those substituting for arsenic. The diffusion constant of interstitial copper has been determined for the first time by Hall and Racette using heavily doped p-type samples in which interstitial copper predominates. The anomalous behavior of zinc, which has an abrupt diffusion front and a strong dependence on zinc concentration, has recently been quantitatively explained in terms of an interstitial-substi-tutional equilibrium-diffusion mechanism. Lithium and silver diffuse mainly interstitially, while the diffusion of phosphorus is complicated by the continual formation ofGap. Junction-migration measurements indicate diiferent results than radiotracer techniques, and this is one problem that still remains, together with discrepancies in cadmium-diffusion results, and an unexplained dependence of impurity diffusion on arsenic pressure. BESIDES the usual insights into the behavior of atoms in solids, studies of diffusion in semiconductors have additional importance for device applications. In fact, the amount of diffusion studies performed on a semiconductor might serve as a simple barometer of its technological importance. Thus, the information accumulated for GaAs is not yet quite comparable to that for germanium or silicon, but considerable knowledge is available. The diffusion of at least fourteen atoms has been investigated for GaAs, and the diffusion constants have been determined for eleven of these. Interesting results were found for GaAs that elucidated problems not previously solved for germanium or silicon. For example, the interstitial-diffusion constant for the very fast diffusant, copper, was first measured in GaAs. Also, solutions for interstitial-substitu-tional equilibrium diffusion in extrinsic material were provided first for GaAs, although they are ap- plicable to germanium, silicon, and other semiconductors. Studies in GaAs firmly established the concept of sublattice diffusion, which should have application in many different compound systems. The purpose of this paper is to review briefly the general state of knowledge concerning diffusion in GaAs. First some general aspects of diffusion will be covered, and next attention will be given to the results mentioned above. Diffusion in GaAs has been measured both by radiotracer and junction-penetration techniques, and some discussion will be given of differences in the two sets of results. The comprehensive work of oldsteinl-' has served as the primary reference for the diffusion of well-behaved substitutional atoms in GaAs. Since a review has recently been presented of many of these reults, details of the diffusion data will not be repeated. Neither will any discussion be given of the experimental techniques of diffusion measurements, except to note here, in passing, the simplicity and effectiveness of the precision lapping device employed by Goldstein.' I) EXPERIMENTAL RESULTS AND DISCUSSION A) Summary of Experimental Results. Diffusion constants D = Do exp(E/kT) have been determined for eleven atoms in GaAs: a,' AS,' n,'" Cd,'" n,' n,8 s, e,' Ag,O CU," and i." These results are summarized in Table I. In addition, diffusion was investigated for phosphorus,4'12 germanium,I3 and ilicon,' but Do and E were not determined. Radiotracer techniques were used for most of the studies except for lithium, where a combination of chemical and electrical techniques was employed, and germanium and silicon, where junction-migration techniques were applied. The diffusion of zinc, manganese, sulfur, and tin was also measured using junction migration.13'14 Goldstein demon-

Jan 1, 1964

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART 1.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust.

Jan 1, 1929

By L. F. Mondolfo

An investigation of the relationship between properties of the elements and type of binary diagram formed was conducted. It was found that, for each type of equilibrium diagram, the factors for the size, valence, electronegativity, period, melting point, entropies of fusion, and sublimation calculated for each pair of elements cover a range of values. However, these factors show sufficient relationship to the equilibrium diagram so that the correlation of several of them can be used to predict the type of diagram formed, or at least limit the choice to only a few types. ThE goal of the metallurgist concerned with alloy development has always been to find a method that predicts the properties that can be obtained when a certain metal is added to another one. In most cases a qualitative predictiton of properties can be made if the equilibrium diagram is known. However, this means that for new metals the alloy development has to start with the experimental determination of the equilibrium diagrams. Because this determination is at least as complicated and time-consuming as the determination of the properties themselves, most alloy development has taken place by trial and error, and the study of the equilibrium diagrams has followed rather than preceded the creation of new alloys. Alloy structures and properties depend on the interaction between electrons and a complete knowledge of these interactions would permit prediction of structure and properties of alloys. Unfortunately direct measurement of these interactions is extremely difficult and somewhat doubtful and only properties that depend on them can be measured easily and with certainty. Study of the relationship between properties of the elements and equilibrium diagrams is not new. Besides the well known Hume-Rothery rule of the necessity of an atomic diameter fit within 15 pct for extensive miscibility in the solid, and the wide knowledge of the effect of such factors as size, electronegativity, electron-atom ratio on solid state features,"' work relating to liquid state and liquid-solid reactions can be found in the literature. Of particular interest is the work by Axon,3 who investigated the effect of size and melting point on a selected number of eutectic and monotectic dia-

Jan 1, 1962

By B. A. Rogers

ACCORDING to petrographic investigations, 1-4 cooled steel furnace slags contain a number of substances that have been shown to be ferro-magnetic5,6 and hence capable of undergoing appreciable changes of susceptibility with temperature. Since any alteration of the suscepti-bility of a constituent affects the average susceptibility of the sample, information concerning the nature of the substance should be deducible from its magnetic behavior. The possibility of obtaining information concerning slags in this way led to the construction of the apparatus to be described. FUNDAMENTAL PRINCIPLES OF APPARATUS The most convenient method of observing changes in mass suscepti-bility? with temperature is the one employed by Curie7 in his original investigation of the changes in magnetic properties of substances at elevated temperatures. As the method has been described frequently in the literature and in textbooks, only a brief review of the fundamental principles need be given here, but the particular arrangements used in the present work require a more detailed description.

Jan 1, 1939

By W. N. Lacey, B. H. Sage

THE results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of gravel screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. INTRODUCTION Gravel screens have been placed in water and oil wells for a number of years1,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. INFLUENCE OF GRAVEL SCREENS UPON PRODUCTIVITY The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the. average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized- spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1941

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By J. J. Jakosky

THE fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.1 One of the most impor-tant measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtain-ing bottom-hole data. The applications of bottom-hole pressure or fluid-level measure-ments are based on simple hydrodynamic principles. Under equilib-rium conditions, pbh = hd + pg + pch [ l] when pbh = bottom-hole pressure, lb. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, lb. per sq. in. per foot, pg = weight of section of gas column 1 in. square from fluid level to casing head, pch = casing-head pressure, lb. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casing head plus the casing-head pressure. At moderate rates of flow, the rate of production is approximately proportional to the difference between the reservoir, or static bottom-hole, pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939